Chemical Engineering Commons^™

Production Of Biofuel Intermediates From Woody Feedstocks Via Fast Pyrolysis And Torrefaction, Jordan Lee Klinger

Dissertations, Master's Theses and Master's Reports - Open

The main objective of this research was to investigate pyrolysis and torrefaction of forest biomass species using a micropyrolysis instrument. It was found that 30-45% of the original sample mass remained as bio-char in the pyrolysis temperature range of 500 - 700˚C for aspen, balsam, and switchgrass. The non-char mass was converted to gaseous and vapor products, of which 10-55% was water and syngas, 2-12% to acetic acid, 2-12% to hydroxypropanone, 1-3% to furaldehyde, and 5-15% to various phenolic compounds. In addition, several general trends in the evolution of gaseous species were indentified when woody feedstocks were pyrolyzed. With increasing …

Designing A Membrane Module For Determining The Permeance Of High Fluxing Membranes And The Testing Rtil-Membranes For Dehumidification., Sikyun Bae

Electronic Theses and Dissertations

Membrane-based gas dehumidification can have technical energy, and economical advantages over other dehumidification technologies. Because, it is simple to install, ease to operate, and take low process cost. Removal of water vapor from gases constitutes a significant expenditure of energy in our society. Dehydration via a membrane process would constitute wide spread energy savings. This thesis explores experimental issues involved with testing Room Temperature Ionic Liquid(RTIL)-membrane for dehumidifying gases. RTIL-membranes or Supported Ionic Liquid Membranes (SILMs) have advantageous performance for the separations of the gas pair CO2/CH4 and CO2/N2. Previous research did not separate the membrane mass transport resistance the …

The Bioactivity And Ion Release Of Titanium-Containing Glass Polyalkenoate Cements For Medical Applications, A. W. Wren, N. M. Cummins, F. R. Laffir, S. P. Hudson, Mark R. Towler

Chemical and Biochemical Engineering Faculty Research & Creative Works

The ion release profiles and bioactivity of a series of Ti containing glass polyalkenoate cements. Characterization revealed each material to be amorphous with a T_g in the region of 650-660°C. The network connectivity decreased (1.83-1.35) with the addition of TiO₂ which was also evident with analysis by X-ray photoelectron spectroscopy. Ion release from cements were determined using atomic absorption spectroscopy for zinc (Zn^₂₊), calcium (Ca^₂₊), strontium (Sr^₂₊), Silica (Si^₄₊) and titanium (Ti4+). Ions such as Zn^₂₊ (0.1-2.0 mg/l), Ca²⁺ (2.0-8.3 mg/l,) Sr²⁺ (0.1-3.9 mg/l), and S^{i4+ …}

The Response Of Pseudomonas Aeruginosa Biofilm To The Presence Of A Glass Polyalkenoate Cement Formulated From A Silver Containing Glass, A. Coughlan, M. P. Ryan, N. M. Cummins, Mark R. Towler

Chemical and Biochemical Engineering Faculty Research & Creative Works

No abstract provided.

Melting Point Depression Of Lead-Free Solder By Gold, Julie E. Thomas

Summer Community of Scholars Posters (RCEU and HCR Combined Programs)

No abstract provided.

Continuous Monitoring Of Bioactive Glass Conversion Using Optical Biosensors, Prajakta Bhagwat

Masters Theses

"The engineered regeneration of bone is a significant challenge being undertaken to treat conditions such as traumatic casualties, bone cancer, osteoporosis, etc. Advances in hard tissue regrowth may potentially lead to significantly improved lives for millions of people. Bioactive glasses as potential materials in the fabrication of scaffolds for hard tissue regeneration have been studied recently. Bone regrowth requires maintenance of optimal levels of oxygen, glucose, phosphate, calcium, and pH. Current work at Missouri S & T's Center for Bone and Tissue Repair and Restoration focuses on developing optical biosensors to monitor: conversion of bioactive glass to hydroxyapatite, ease of …

Effect Of Titanium Dioxide Supports On The Activity Of Pt-Ru Toward Electrochemical Oxidation Of Methanol, Roderick E. Fuentes, Brenda L. García, John W. Weidner

Faculty Publications

TiO₂and Nb-TiO₂ were investigated as stable supports for Pt-Ru electrocatalysts towards methanol oxidation. X-ray photo-electron spectroscopy (XPS) data for all these TiO₂-based supports show oxidation states of Ti⁴⁺, with no Ti³⁺, suggesting low electronic conductivity. However, the deposition of metal nanoparticles onto the supports at loadings of 60 wt% metal dramatically increased conductivity, making these electrodes (metal particles + support) suitable for electrochemistry even though the supports have low conductivity. For some of these TiO₂-based supports, the activity of Pt-Ru towards methanol oxidation was excellent, even surpassing the activity …

Optical Cell For Combinatorial In Situ Raman Spectroscopic Measurements Of Hydrogen Storage Materials At High Pressures And Temperatures, Jason R. Hattrick-Simpers, Wilbur S. Hurst, Sesha S. Srinivasan, James E. Maslar

Faculty Publications

An optical cell is described for high-throughput backscattering Raman spectroscopic measurements of hydrogen storagematerials at pressures up to 10 MPa and temperatures up to 823 K. High throughput is obtained by employing a 60 mm diameter × 9 mm thick sapphire window, with a corresponding 50 mm diameter unobstructed optical aperture. To reproducibly seal this relatively large window to the cell body at elevated temperatures and pressures, a gold o-ring is employed. The sample holder-to-window distance is adjustable, making this cell design compatible with optical measurement systems incorporating lenses of significantly different focal lengths, e.g., microscope objectives and single element …

Single-Particle Model For A Lithium-Ion Cell: Thermal Behavior, Meng Guo, Godfrey Sikha, Ralph E. White

Faculty Publications

The single-particle model presented by Santhanagopalan et al. [ J. Power Sources , 156 , 620 (2006)] is extended to include an energy balance. The temperature dependence of the solid phase diffusion coefficient of the lithium in the intercalation particles, the electrochemical reaction rate constants, and the open circuit potentials (OCPs) of the positive and negative electrodes are included in the model. The solution phase polarization is approximated using a nonlinear resistance, which is a function of current and temperature. The model is used to predict the temperature and voltage profiles in a lithium-ion cell during galvanostatic operations. The single-particle …

A Study On The Use Of Inverse Opals Composed Of Zinc Oxide Aggregate Popcorn Particles To Improve The Efficiency Of Dye- Sensitized Solar Cells, Roger Chang

Dissertations and Theses

"In this work, modifications applicable to the working electrode of a dye--‐sensitized solar cell (DSSC) are explored in order to enhance efficiency. Certain compositional and structural changes to the architecture of the electrode are examined. First, the ZnO nanoparticles that are commonly utilized in DSSCs are replaced with ZnO nanoparticle aggregates, also known as ZnO popcorn particles. Subsequently, electrophoretic deposition (EPD) is used to assemble the popcorn particles into an inverse opal structure. This is a unique application of EPD, which has previously been used to infiltrate nanoparticles (d ≤20nm range) Into opal templates, demonstrating the applicability of the technique …

Characterizations Of Partially Reduced Polyoxometalate Catalysts Using Ammonia Adsorption Microcalorimetry And Methanol Oxidation Studies / By Suresh Babu Bommineni., Suresh Babu Bommineni

Dissertations, Master's Theses and Master's Reports - Open

Phosphomolybdic acid (H₃PMo₁₂O₄₀) along with niobium,pyridine and niobium exchanged phosphomolybdic acid catalysts were prepared. Ammonia adsorption microcalorimetry and methanol oxidation studies were carried out to investigate the acid sites strength acid/base/redox properties of each catalyst. The addition of niobium, pyridine or both increased the ammonia heat of adsorption and the total uptake. The catalyst with both niobium and pyridine demonstrated the largest number of strong sites. For the parent H₃PMo₁₂O₄₀ catalyst, methanol oxidation favors the redox product. Incorporation of niobium results in similar selectivity to redox products but also …

Development And Testing Of An Asymmetric Capacitor With A Nickel-Carbon Foam Positive Electrode, Wen Nee Yeo

Dissertations, Master's Theses and Master's Reports - Open

Electrochemical capacitors (ECs), also known as supercapacitors or ultracapacitors, are energy storage devices with properties between batteries and conventional capacitors. EC have evolved through several generations. The trend in EC is to combine a double-layer electrode with a battery-type electrode in an asymmetric capacitor configuration. The double-layer electrode is usually an activated carbon (AC) since it has high surface area, good conductivity, and relatively low cost. The battery-type electrode usually consists of PbO₂ or Ni(OH)₂.

In this research, a graphitic carbon foam was impregnated with Co-substituted Ni(OH)₂ using electrochemical deposition to serve as the positive electrode …

Graphite Exfoliation By Supercritical Carbon Dioxide Extraction, Chaiyaporn Wattanaprayoon

Dissertations, Master's Theses and Master's Reports - Open

Supercritical carbon dioxide is used to exfoliate graphite, producing a small, several-layer graphitic flake. The supercritical conditions of 2000, 2500, and 3000 psi and temperatures of 40°, 50°, and 60°C, have been used to study the effect of critical density on the sizes and zeta potentials of the treated flakes. Photon Correlation Spectroscopy (PCS), Brunauer-Emmett-Teller (BET) surface area measurement, field emission scanning electron microscopy (FE-SEM), and atomic force microscopy (AFM) are used to observe the features of the flakes. N-methyl-2-pyrrolidinone (NMP), dimethylformamide (DMF), and isopropanol are used as co-solvents to enhance the supercritical carbon dioxide treatment. As a result, the …

Modeling Of Diesel Particulate Filter Filtration And Regeneration For Transient Driving Schedules, Di Huang

Dissertations, Master's Theses and Master's Reports - Open

Due to their high thermal efficiency, diesel engines have excellent fuel economy and have been widely used as a power source for many vehicles. Diesel engines emit less greenhouse gases (carbon dioxide) compared with gasoline engines. However, diesel engines emit large amounts of particulate matter (PM) which can imperil human health. The best way to reduce the particulate matter is by using the Diesel Particulate Filter (DPF) system which consists of a wall-flow monolith which can trap particulates, and the DPF can be periodically regenerated to remove the collected particulates.

The estimation of the PM mass accumulated in the DPF …

Scaling Properties At Freeze-Out In Relativistic Heavy-Ion Collisions, M. M. Aggarwal, Z. Ahammed, A. V. Alakhverdyants, I. Alekseev, J. Alford, B. D. Anderson, S. Bueltmann, I. Koralt, D. Plyku, Star Collaboration

Physics Faculty Publications

Identified charged pion, kaon, and proton spectra are used to explore the system size dependence of bulk freeze-out properties in Cu+Cu collisions at √sNN=200 and 62.4 GeV. The data are studied with hydrodynamically motivated blast-wave and statistical model frameworks in order to characterize the freeze-out properties of the system. The dependence of freeze-out parameters on beam energy and collision centrality is discussed. Using the existing results from Au + Au and pp collisions, the dependence of freeze-out parameters on the system size is also explored. This multidimensional systematic study furthers our understanding of the QCD phase diagram revealing the importance …

Experimental Study Of The Interaction Between Surfactants And Preformed Particle Gels, Farag Awadh Muhammed

Masters Theses

"Gel and surfactant treatment are two principle methods to reduce water production and enhance oil recovery (EOR). However, either method by itself has limitations that can be avoided by combining the two. Gel treatment can improve sweep efficiency but has little effect on micro-displacement efficiency. Surfactants are mainly used to improve displacement efficiency but have little effect on sweep efficiency. This research sought to investigate whether the combination of gel and surfactant treatments can be used to significantly enhance oil recovery while reducing water production for extremely heterogeneous mature reservoirs. A newer trend in gel treatments is preformed particle gels …

Shale Gas Rock Characterization And 3d Submicron Pore Network Reconstruction, Malek Elgmati

Masters Theses

"Determining shale gas petrophysical properties is the cornerstone to any reservoir-management practice. Hitherto, conventional core analyses are inadequate to attain the petrophysical properties of shale gas at submicron-scale. This study combines interdisciplinary techniques from material science, petrophysics, and geochemistry to characterize different shale gas samples from North America including Utica, Haynesville and Fayetteville shale gas plays. Submicron pore structure, clay mineralogy, wettability and organic matter maturation were investigated to evaluate the petrophysical properties of shale gas rocks and to determine the impact of organic and inorganic matters on wettability alteration for different fracturing fluids on shale gas rocks.

High pressure …

Mesh Optimization Of Finite Element Models Of Wellbore Stress Analysis, Ming-Yen Lee

Masters Theses

"Numerical modeling methods such as the widely used finite element method provide an excellent opportunity to analyze the wellbore state of stress for a variety of applications such as wellbore integrity, wellbore design or hydraulic fracturing. However, numerical modeling methods introduce errors by nature and may not precisely match the analytical solution if the meshing of the numerical model is not carefully taken care of. This study presents a parametric study of the meshing parameters mesh density, element type, and model size for 2-dimensional and 3-dimensional vertical wellbore models under three different types of boundary conditions, and a guideline for …

Effects Of A Nickel Reactor Liner And Other Reaction Variables During Supercritical Water Reformation Of Glycerin, Michael S. Stever

Masters Theses

"The non-catalytic reformation of glycerin using supercritical water was conducted in a 400-mL tubular reactor constructed of Haynesʼ Alloy 230. The evaluated parameters for this thesis include water-to-glycerin molar ratios ranging from 3 to 24 and reactor temperatures ranging from 500⁰C to 700⁰C. In addition, experiments were performed using the Haynes' Alloy 230 reactor both without a liner and with a Nickel 201 liner. Space time was maintained at approximately 100 seconds and the reactor pressure was kept constant at 24.1 MPa. The resultant effect on product gas composition and carbon gasification was determined. The product gases consisted of a …

Synthesis And Characterization Of Polymeric Antioxidant Delivery Systems, Paritosh P. Wattamwar

Theses and Dissertations--Chemical and Materials Engineering

Even though the role of oxidative stress in a variety of disease states is known, strategies to alleviate this oxidative stress by antioxidants have not been able to achieve clinical success. Particularly, treatment of oxidative stress by small molecule antioxidants has not received due attention because of the challenges associated with its delivery. Antioxidant polymers, where small molecule antioxidants are incorporated into the polymer backbone, are an emerging class of materials that can address some of these challenges.

In this work, biodegradable polymers incorporating phenolic antioxidants in the polymer backbone were synthesized. Antioxidant polymers were then characterized for their in …

Stability Of Affinity Based Layer-By-Layer Polymeric Self-Assemblies For Oral Wound Applications, Sundar Prasanth Authimoolam

Theses and Dissertations--Chemical and Materials Engineering

Oral mucositis is a painful and debilitating chronic inflammatory condition that can result from chemo and/or radiotherapy. While current treatment strategies which provide temporary relief exist, there is still an unmet clinical need for a robust long active barrier strategy which can simultaneously provide protection and release drug to enhance the wound healing response. It is proposed that an affinity based layer-by-layer self-assembled barrier administered as a series of mouth rinses can allow for wound specific drug delivery, providing an effective regenerative therapy.

In this work, biotinylated poly(acrylic acid) is used to develop LBL assemblies based upon biotin-streptavidin affinity interactions. …

Dynamic Relaxation Properties Of Aromatic Polyimides And Polymer Nanocomposites, Anthony C. Comer

Theses and Dissertations--Chemical and Materials Engineering

The dynamic relaxation characteristics of Matrimid^® (BTDA-DAPI) polyimide and several functionalized aromatic polyimides have been investigated using dynamic mechanical and dielectric methods. The functionalized polyimides were thermally rearranged to generate polybenzoxazole membranes with controlled free volume characteristics. All polyimides have application in membrane separations and exhibit three motional processes with increasing temperature: two sub-glass relaxations (ƴ and β transitions), and the glass-rubber (α) transition. For Matrimid, the low-temperature ƴ transition is purely non-cooperative, while the β sub-glass transition shows a more cooperative character as assessed via the Starkweather method. For the thermally rearranged polyimides, the ƴ transition is a …

Photocatalytic Destruction Of Halogenated Organic Compounds In Water With A New Photocatalyst, Mabruka Hadidan

Open Access Theses & Dissertations

In this research, a newly developed high surface area semiconductor porous material was synthesized from potassium titanium niobium mixed oxide (KTiNbO5) to be used as a photo catalyst in the presence of UV light to degrade halogenated organic compounds in water. The goal of the project was to investigate the catalytic activity of the material for its effectiveness in the degradation of the halogenated organic compounds, and it is the first investigation of this new photocatalyst with halogenated compounds. Model compounds dichloromethane, 1-chlorobutane, chlorobenzene, and trifluoroacetic acid in aqueous solutions were tested with the photocatalyst under ultraviolet light irradiation, using …

Cactus Mucilage-Assisted Heavy Metal Separation: Design And Implementation, Dawn Iona Fox

USF Tampa Graduate Theses and Dissertations

Natural contamination of groundwater by arsenic (As) has become a critical public health threat in many parts of the world. The well-known regions associated with As contamination of groundwater are Bangladesh and West Bengal, India where approximately 100 million people are exposed to high levels of arsenic by drinking arsenic-contaminated groundwater and about 35 million are already affected. Long-term drinking of arsenic-contaminated water leads to arsenicosis, which is characterized by cancers of the skin, organ disease and certain other types of cancer. Affected developing communities are at higher risk because they may not have access to conventional water treatment facilities. …

Studies On Silicon Nmr Characterization And Kinetic Modeling Of The Structural Evolution Of Siloxane-Based Materials And Their Applications In Drug Delivery And Adsorption, Jyotrhirmai Ambati

University of Kentucky Doctoral Dissertations

This dissertation presents studies of the synthetic processes and applications of siloxane-based materials. Kinetic investigations of bridged organoalkoxysilanes that are precursors to organic-inorganic hybrid polysilsesquioxanes are a primary focus. Quick gelation despite extensive cyclization is found during the polymerization of bridged silane precursors except for silanes with certain short bridges. This work is an attempt to characterize and understand some of the distinct features of bridged silanes using experimental characterization, kinetic modeling and simulation. In addition to this, the dissertation shows how the properties of siloxane- materials can be engineered for drug delivery and adsorption.

The phase behavior of polymerizing …

Solution Phase And Membrane Immobilized Iron-Based Free Radical Reactions: Fundamentals And Applications For Water Treatment, Scott Romak Lewis

University of Kentucky Doctoral Dissertations

Membrane-based separation processes have been used extensively for drinking water purification, wastewater treatment, and numerous other applications. Reactive membranes synthesized through functionalization of the membrane pores offer enhanced reactivity due to increased surface area at the polymer-solution interface and low diffusion limitations. Oxidative techniques utilizing free radicals have proven effective for both the destruction of toxic organics and non-environmental applications. Most previous work focuses on reactions in the homogeneous phase; however, the immobilization of reactants in membrane pores offers several advantages. The use of polyanions immobilized in a membrane or chelates in solution prevents ferric hydroxide precipitation at near-neutral pH, …

Investigation On Water-Borne Intumescent Fire Protective Coatings For Steel., Yew Ming Chian

Student Works (2010-2019)

This research studies the efficiency of different water-borne intumescent formulations which incorporate chicken eggshell (CES) as a novel bio-filler, designed to protect steel in the event of a fire. The coating is based on these three flame-retardant additives: ammonium polyphosphate phase II, melamine and pentaerythritol (combination referred to as AMP). CES, silica fume (SF) and epoxy emulsion were incorporated either individually or in combination into the flame-retardant additives. The first part of the study develops and evaluates AMP, AMP+SF and AMP+SF+CES intumescent formulation systems, respectively. The best formulation produced was the AMP+SF+CES system which was subsequently selected for the next …

Analytical Design Method For Cold Production Of Heavy Oil With Bottom Water Using Bilateral Sink Wells, Wenting Qin

LSU Doctoral Dissertations

Few heavy oil reservoirs with strong bottom water drives have been developed successfully because of severe water coning. Water coning tends to cause low ultimate recovery, low well productivity, and high water production. Although thermal and gravity-assisted methods might improve recovery in oil reservoirs, such methods are widely perceived as either economically unfavorable or technologically infeasible. This study proposes a new, cold production technique, called Bilateral Water Sink (BWS), to meet those challenges. The BWS method suppresses water cresting by producing oil and water simultaneously from separate, horizontal wells completed in the oil and water zones; the oil and water …

Silicon Nanowire Anode For Lithium-Ion Batteries: Fabrication, Characterization And Solid Electrolyte Interphase, Wanli Xu

LSU Doctoral Dissertations

Depletion of fossil fuels and concerns over CO2 emission have driven the development of electric vehicles (EVs) with high-energy efficiencies and low emissions. Lithium-ion rechargeable batteries, compared to lead acid, nickel cadmium, nickel metal hydroxide, and other popular rechargeable batteries, are considered as the most promising candidates for EVs for their high operating voltage and high energy density. Silicon nanowires are considered as lithium-ion battery anodes for their ultra high capacity at 4200 mAh·g-1 (10× higher than conventional graphite anode), as well as stress accommodation for reversible lithiation and delithiation. Silicon nanowires were fabricated via metal assisted electroless etching, and …

Catalytic Hydrogenation Of Co To Higher Alcohols, Nachal Devi Subramanian

LSU Doctoral Dissertations

The interest in converting synthesis gas to alcohols and oxygenated fuel additives via CO hydrogenation is growing rapidly due to the increasing rise in oil prices. Among the potential end products, ethanol is desirable since it serves as a clean alternative fuel, a gasoline blend, and a hydrogen carrier to supply fuel cells. The high cost and limited availability of the most active/selective Rh-based catalysts has led to the development of base metal catalysts such as modified Cu-based catalysts. Literature suggests that a combination of Co (or Mn) with Cu can facilitate higher alcohol formation by a non-dissociative adsorption of …