Open Access. Powered by Scholars. Published by Universities.®
Articles 61 - 90 of 656
Full-Text Articles in Chemical Engineering
Repeatability Of Alkanolamines In Carbon Dioxide Capture After Mineralization, Titiwut Sirima
Repeatability Of Alkanolamines In Carbon Dioxide Capture After Mineralization, Titiwut Sirima
Chulalongkorn University Theses and Dissertations (Chula ETD)
The mineralization reaction between alkanolamines solution loaded with CO2 and calcium ions (Ca2+) produced calcium carbonate precipitate under an ambient condition, which reduced energy for thermal regeneration of alkanolamines solution. This work represented alkanolamines as monoethanolamine (MEA), diethanolamine (DEA), and triethanolamine (TEA). In addition, calcium chloride (CaCl2), calcium sulphate (CaSO4) and calcium hydroxide (Ca(OH)2) were used as calcium sources. Utilization of calcium hydroxide (Ca(OH)2) as a calcium source in the mineralization reaction resulted in the supernatant retaining its ability to capture carbon dioxide over 89%, which is similar to thermal regeneration. The mineral regeneration and the thermal regeneration can regenerate …
Utility Optimization Via Multi-Section Heat Integration Approach For Multi-Period Operations, Ariyachai Silprasert
Utility Optimization Via Multi-Section Heat Integration Approach For Multi-Period Operations, Ariyachai Silprasert
Chulalongkorn University Theses and Dissertations (Chula ETD)
Heat Exchanger Network (HEN) optimization is essential for achieving utility conservation and minimizing the Total Annual Cost (TAC) by maximizing heat recovery between process streams. This study investigates on single and multi-section heat integration within a caprolactam (CPL) plant, conducted in collaboration with a petrochemical company. The investigation comprehensively addresses multi-period operations, considering production rate variability at 60%, 80%, and 100% loads. This variability is due to fluctuating operating conditions influenced by economic factors, as well as start-up and shut-down schedules. This work utilizes process simulation namely Aspen Plus and establishes HEN solutions using Aspen Energy Analyzer (AEA) and conventional …
Techno-Economic Analysis Of Dimethyl Ether Production Via Direct Hydrogenation Of Co2, Boonyasit Farkham
Techno-Economic Analysis Of Dimethyl Ether Production Via Direct Hydrogenation Of Co2, Boonyasit Farkham
Chulalongkorn University Theses and Dissertations (Chula ETD)
To achieve carbon neutrality by 2050, alternative and sustainable fuels are receiving significant attention. One of the interesting options is dimethyl ether (DME), which can be synthesized from CO2. This research aimed to simulate DME production from CO2 by comparing indirect synthesis (two-step process) and direct synthesis (one-step process) methods. This study found that the one-step process had negative net CO2 emissions, with values of -1.16 tons CO2 per ton of DME. It also consumed less energy compared to that of the two-step process. This was because the amount of methanol generated in the two-step process was higher than in …
วัสดุผสมขั้นสูงของไบโอชาร์และโครงสร้างโลหะอินทรีย์ (Mofs) สำหรับการเก็บไฮโดรเจน, แซมสัน บามิเดเล อาคินโดเย
วัสดุผสมขั้นสูงของไบโอชาร์และโครงสร้างโลหะอินทรีย์ (Mofs) สำหรับการเก็บไฮโดรเจน, แซมสัน บามิเดเล อาคินโดเย
Chulalongkorn University Theses and Dissertations (Chula ETD)
การพึ่งพาเชื้อเพลิงฟอสซิลในยุคอุตสาหกรรม โดยเฉพาะอย่างยิ่งสำหรับการขนส่ง ส่งผลให้การปล่อยก๊าซเรือนกระจก (GHG) เพิ่มขึ้นอย่างมาก ซึ่งมีส่วนทำให้เกิดการเปลี่ยนแปลงสภาพภูมิอากาศ การจัดการกับปัญหาสิ่งแวดล้อมนี้จำเป็นต้องมีแนวทางแก้ไขที่เป็นนวัตกรรมเพื่อลดการพึ่งพาเชื้อเพลิงแบบเดิมๆ การศึกษานี้มุ่งเน้นไปที่การพัฒนาวัสดุคอมโพสิตขั้นสูงที่ประกอบด้วยถ่านชีวภาพและกรอบโลหะ-อินทรีย์ (MOF) เพื่อการจัดเก็บไฮโดรเจนอย่างมีประสิทธิภาพ เพื่อลดการใช้เชื้อเพลิงฟอสซิลและผลกระทบต่อสิ่งแวดล้อม เราประเมินวัสดุแต่ละชนิด (ถ่านชีวภาพและ MOF) และส่วนประกอบของวัสดุเหล่านี้เกี่ยวกับความสมบูรณ์ของโครงสร้าง สัณฐานวิทยาของพื้นผิว ความพรุน การกระจายขนาดรูพรุน กลุ่มฟังก์ชันของพื้นผิว และความสามารถในการกักเก็บไฮโดรเจน ผลการศึกษาครั้งนี้สามารถปูทางไปสู่ความก้าวหน้าใหม่ๆ ในด้านวัสดุคอมโพสิตและกระทรวงการคลังเฉพาะทางสำหรับการจัดเก็บไฮโดรเจน ซึ่งส่งผลกระทบอย่างมีนัยสำคัญต่อความยั่งยืนและผลกระทบต่อสิ่งแวดล้อมของการขนส่งในอนาคต
Techno-Economic Analysis Of Pre-Treatment Methods For Monoethanolamine (Mea)Co2 Capture Process, Nida Isarapreeda
Techno-Economic Analysis Of Pre-Treatment Methods For Monoethanolamine (Mea)Co2 Capture Process, Nida Isarapreeda
Chulalongkorn University Theses and Dissertations (Chula ETD)
Global warming is the increase in the earth's overall temperature due to human activities, primarily the burning of fossil fuels, leading to the greenhouse effect. Greenhouse gases cause temperatures to rise, lead to climate change, which encompasses alterations in weather patterns. In Thailand, the industries with significant greenhouse gas emissions include electricity generation, cement production, and steel production. To remove CO2 emissions, the carbon capture process is focused on this research. The Monoethanolamide (MEA) process stands out for its lowest capital investment cost due to its simplicity and minimal equipment requirements. SO2 and NOX can react with amine-based solvents used …
The Production Of Encapsulated Holy Basil Oil Powder Via Different Scales Of Spray Drying Process., Chanakarn Chungmarisakul
The Production Of Encapsulated Holy Basil Oil Powder Via Different Scales Of Spray Drying Process., Chanakarn Chungmarisakul
Chulalongkorn University Theses and Dissertations (Chula ETD)
The spray drying process is widely utilized in food manufacturing and pharmaceuticals for products like seasoning powder, milk powder, and medicine. This research investigates the scale-up of the spray drying process from laboratory to commercial scale with maintaining the product characteristic. A key aspect of the study is the encapsulation technique applied to prolong the release of essential oils from holy basil, encapsulating the essential substances (liquid, suspension, or emulsion) in nanoparticle form with hot air flow. The study utilizes the Aspen program, incorporating mass and energy balance calculations for simulation. The results, assuming similar particle size, water evaporation per …
Process Design And Evaluation Of Value-Added Chemical Production From Crude Glycerol Obtained From Biodiesel Industry, Piyawan Thanahiranya
Process Design And Evaluation Of Value-Added Chemical Production From Crude Glycerol Obtained From Biodiesel Industry, Piyawan Thanahiranya
Chulalongkorn University Theses and Dissertations (Chula ETD)
Excessive glycerol, a major by-product of biodiesel industry, has been increasingly utilized as a platform chemical feedstock for production of value-added chemicals. Accordingly, this study aims to simulate the productions of propionic acid (PA), succinic acid (SA), and dihydroxyacetone (DHA) from glycerol via fermentation. For PA production, diluents and extractants as well as techniques in the back-extraction are investigated, whereas the techniques of reactive extraction and direct crystallization, as well as the use of dimethyl sulfoxide (DMSO) as an electron acceptor for SA production are investigated. Meanwhile, the effects of carbon source types and glycerol types on the DHA productivity …
Techno-Economic Analysis And Intensification Of Biosurfactant Production From Palm Fatty Acid For Oil Recovery Enhancement, Chanapol Charoentanaworakun
Techno-Economic Analysis And Intensification Of Biosurfactant Production From Palm Fatty Acid For Oil Recovery Enhancement, Chanapol Charoentanaworakun
Chulalongkorn University Theses and Dissertations (Chula ETD)
Currently, Biosurfactants are receiving the interest as a substitute for surfactants synthesized from petroleum products due to their biodegradability. Palm oil derivatives are one of the interesting candidates of biosurfactant production because of the superior properties of hydrocarbon structure in the range of C16-C18. Thus, this research studied the economic and environmental impact analysis of production processes, and adsorption and oil recovery performance for different anionic biosurfactants synthesized from palm oil derivatives, i.e. palm fatty acid distillate (PFAD). Moreover, the optimal design and essential operating condition of batch reactive distillation column were also studied to intensify the equilibrium limitation of …
Shape Memory Polymer Based On Copolybenzoxazines: Effects Of Chain Length Of Aliphatic Monoamines On Shape Memory Performance, Attachai Sriwattana
Shape Memory Polymer Based On Copolybenzoxazines: Effects Of Chain Length Of Aliphatic Monoamines On Shape Memory Performance, Attachai Sriwattana
Chulalongkorn University Theses and Dissertations (Chula ETD)
This research was successful in completely synthesizing benzoxazine copolymers for shape memory polymers (SMPs) by mixing bisphenol A-aniline (BA-a) and bisphenol A-aliphatic monoamines of various chain lengths (BA-aMAs). Our studies have shown that shorter chain lengths will provide higher crosslinking densities, which play an important role in promoting the stiffness of the polymer, resulting in a higher shape-fixity ratio (Rf). While longer chains result in a lower crosslinking density and a larger free volume, thus promoting a higher shape-recovery ratio (Rr), Therefore, selecting the appropriate aliphatic monoamine chain length is crucial. From the study of this work, it was found …
Sustainable Toughening Of Polylactic Acid With Ultra-Fine Fully Vulcanized Powdered Natural Rubber, Reza Gholami
Sustainable Toughening Of Polylactic Acid With Ultra-Fine Fully Vulcanized Powdered Natural Rubber, Reza Gholami
Chulalongkorn University Theses and Dissertations (Chula ETD)
This study investigated the sustainable toughening of polylactic acid (PLA) by incorporating ultra-fine fully vulcanized powdered natural rubber graft-copolymerized with poly-styrene-co-acrylonitrile (UFPNR-SAN). We investigated the effect of the styrene-to-acrylonitrile ratio (ST:AN) used during the grafting process on the final UFPNR-SAN compatibility with PLA. The ST:AN ratio was systematically varied during the grafting reaction to prepare UFPNR-SAN with a range of different surface energies. The ST:AN ratio of 4:1 resulted in higher compatibility of UFPNR-SAN with the PLA matrix among other ratios. This could be explained by the desirable interfacial interactions and better dispersion shown by the contact angle measurements and …
Green Synthesis For Silver Nanoparticle /Natural Rubber/ Nanocellulose Bio-Polymeric Composites, Puttakhun Meemai
Green Synthesis For Silver Nanoparticle /Natural Rubber/ Nanocellulose Bio-Polymeric Composites, Puttakhun Meemai
Chulalongkorn University Theses and Dissertations (Chula ETD)
A green synthesis method was developed to produce biobased semiconducting composites of silver nanoparticles (AgNPs), skim natural rubber (SNR), and bacteria cellulose. A solution of silver nitrate (AgNO3) ranging from 40 to 160 mM was added to skim natural rubber latex (SNRL) to facilitate the reduction of silver ions to AgNPs at temperatures between 50 and 80 °C. Subsequently, BC pellicle was immersed in the prepared AgNPs-SNRL suspension for 48 hours, followed by washing and drying. The resulting AgNPs/SNR/BC films were then analyzed for their chemical, mechanical, antibacterial, and electrical properties. The strain at break of the films was significantly …
Methyl Isobutyrate Production Via Hydrogenation Of Methyl Methacrylate Derived From Pyrolysis Of Acrylic Plastic Waste, Ramzi Nasser Ahmed Saif
Methyl Isobutyrate Production Via Hydrogenation Of Methyl Methacrylate Derived From Pyrolysis Of Acrylic Plastic Waste, Ramzi Nasser Ahmed Saif
Chulalongkorn University Theses and Dissertations (Chula ETD)
According to zero waste and upcycling policy, this work aims to utilize waste polymethyl methacrylate (PMMA) to methyl isobutyrate (MIB) via hydrogenation over nickel (Ni) based catalysts supported on commercial zeolites: HY, H-Beta-27 (SiO2/Al2O3 = 27 by mole), H-Beta-40 (SiO2/Al2O3 = 40 by mole) and H-ZSM-5. The appropriate catalyst support was first screen by using MMA monomer as the substrate for hydrogenation. Under 30 bar initial H2 pressure (PH2) at 250 °C for 3 h, Ni/H-Beta-27 catalyst effectively promoted hydrogenation to achieve 85% MMA conversion with 56.2 wt% MIB yield because of its larger external surface area and pore size. …
Batch And Fixed-Bed Adsorption Of Ciprofloxacin Using Magnetic Biochar From Macadamia Nutshell, Sakonsupa Damdib
Batch And Fixed-Bed Adsorption Of Ciprofloxacin Using Magnetic Biochar From Macadamia Nutshell, Sakonsupa Damdib
Chulalongkorn University Theses and Dissertations (Chula ETD)
In this research, the utilization of macadamia nutshell as a potential adsorbent for ciprofloxacin (CIP) removal was investigated. The distinctive features of macadamia nutshell, characterized by its lignocellulosic composition and hardness, make it suitable as a precursor for synthesizing magnetic biochar, aimed at CIP adsorption in both batch and fixed-bed column processes. The influence of temperature activation and carbonization temperature on the properties of the resulting biochar was examined. Macadamia nutshell impregnated with a 0.10 M iron nitrate solution and carbonized under a nitrogen atmosphere at 800°C (MB-BI-800) exhibited the highest micropore and mesopore volumes, with values of 0.14 and …
Verification Of Oil Recovery Mechanism Through Alteration Of Relative Permeability Curve And Analytical Measurements, Tina Tharn
Chulalongkorn University Theses and Dissertations (Chula ETD)
In the petroleum production industry, there are several methods that can be utilized to increase oil recovery. These methods are so-called Enhanced Oil Recovery (EOR). Nowadays, Low Salinity Water Flooding (LSWF) is one of the considerable of those techniques due to its cost and simplicity. However, understanding its main oil recovery mechanism is still limited. Therefore, the investigation of oil mechanism provided by LSWF would help refine its application to oilfields. In this study, the Johnson–Bossler–Naumann (JBN) approach is employed to examine relative permeability curves during LSWF in different rock formations including clean sandstone (SS), shaly-sandstone (SHS), and dolostone (DL). …
ผลของแกรฟีนควอนตัมดอทต่อการเจริญเติบโตและฤทธิ์ต้านอนุมูลอิสระของต้นถั่วเขียวและต้นอ่อนทานตะวัน, วราวุธ คงแสงชัย
ผลของแกรฟีนควอนตัมดอทต่อการเจริญเติบโตและฤทธิ์ต้านอนุมูลอิสระของต้นถั่วเขียวและต้นอ่อนทานตะวัน, วราวุธ คงแสงชัย
Chulalongkorn University Theses and Dissertations (Chula ETD)
แกรฟีนควอนตัมดอท (Graphene Quantum Dots) จัดเป็นวัสดุนาโนที่มีคุณสมบัติเชิงแสงที่เป็นเอกลักษณ์จากผลของการกักกันเชิงควอนตัม อีกทั้งยังมีความเข้ากันได้กับเซลล์ของสิ่งมีชีวิตค่อนข้างสูง รวมทั้งความเป็นพิษต่อเซลล์ของสิ่งมีชีวิตที่ต่ำ สำหรับงานวิจัยนี้เป็นการศึกษาผลของการเติม GQDs ที่มีต่อการเจริญเติบโตและฤทธิ์ต้านอนุมูลอิสระ ซึ่งเมล็ดต้นกล้าที่ใช้ในการศึกษา คือ เมล็ดถั่วเขียวและเมล็ดต้นอ่อนทานตะวัน โดยจะติดตามการเจริญเติบโตในลักษณะเทคนิคต่างๆของการเติม GQDs 3 เทคนิควิธีการ ได้แก่ 1.) การแช่เมล็ดด้วย GQDs ที่ความเข้มข้นต่างๆ 2.) การเติม GQDs ให้กับต้นกล้าในลักษณะการใส่ปุ๋ยที่ความเข้มข้นต่างๆ และ 3.) การกระทำทั้งเทคนิควิธีการที่ 1 และ 2 ร่วมกันในช่วงความเข้มข้น 0 - 0.3 mg/mL ของ GQDs พบว่าต้นกล้าถั่วเขียวที่ความเข้มข้น 0.3 mg/mL ด้วยเทคนิควิธีการเติม GQDs ให้กับต้นกล้าในลักษณะการใส่ปุ๋ยมีฤทธิ์ต้านอนุมูลอิสระมากที่สุดถึง 33.67% เมื่อเทียบกับต้นกล้า control แต่สำหรับต้นกล้าต้นอ่อนทานตะวันนั้นจะพบว่าที่ความเข้มข้น 0.3 mg/mL เทคนิควิธีร่วมกันทั้ง 2 วิธีการจะให้ฤทธิ์ต้านอนุมูลอิสระมากที่สุด 38.24% เมื่อเทียบกับต้นกล้า control
Effects Of Sio2 Coating On Activity Of Ru/Tio2 Catalyst For Co2 Methanation, Fasai Chaisalee
Effects Of Sio2 Coating On Activity Of Ru/Tio2 Catalyst For Co2 Methanation, Fasai Chaisalee
Chulalongkorn University Theses and Dissertations (Chula ETD)
Hydrogenation of carbondioxide to methane has the potential to effectively decrease the release of excessive CO2 emissions. The Ru/TiO2-rutile catalyst has been previously reported as the best catalytic activity for methane generation under mild operating conditions. However, no catalyst has been developed that approaches the efficiency of this Ru/rutile. This study aims to develop a catalyst that can overcome the performance of the Ru/rutile catalyst. This work investigates Ru catalysts supported on TiO2 and core-shell TiO2@SiO2 catalysts with various phase structures and SiO2 thicknesses were prepared using incipient wetness impregnation of Ru precursor on TiO2 and core-shell TiO2@SiO2 supports. The …
Microencapsulation Of Holy Basil Oil Using Modified Starch By Spray Drying Method, Artima Lairattanakul
Microencapsulation Of Holy Basil Oil Using Modified Starch By Spray Drying Method, Artima Lairattanakul
Chulalongkorn University Theses and Dissertations (Chula ETD)
Holy basil is a local herb that can planted all over Thailand. It is the significant ingredient in Thai famous dish named “Pad ga prao” because of its unique scent which is released when cooked. Apart from the cuisine, its essential oil has been used in various industries including cosmetics, perfumery, and pharmaceuticals. However, their degradation under light, moisture, and high temperature during storage is the main problem of their utility. In this research, the encapsulation process is selected to prevent the problem. The modified starch was used as wall materials. Holy basil oil (HBO) has three main components: Eugenol, …
Effect Of Rice Straw Loading On Morphological, Thermal, Gas Barrier, And Mechanical Properties Of Poly(Lactic Acid)/Poly(3-Hydroxybutyrate-Co-4-Hydroxybutyrate) Blend Films, Danaipat Tuangwattanasin
Effect Of Rice Straw Loading On Morphological, Thermal, Gas Barrier, And Mechanical Properties Of Poly(Lactic Acid)/Poly(3-Hydroxybutyrate-Co-4-Hydroxybutyrate) Blend Films, Danaipat Tuangwattanasin
Chulalongkorn University Theses and Dissertations (Chula ETD)
This research focuses on enhancing the properties of polylactic acid (PLA), a biodegradable polymer known for its potential in mitigating waste accumulation issues. The inherent brittleness of PLA poses a significant challenge. To overcome this limitation, the study explores the incorporation of the biodegradable polymer poly(3-hydroxybutyrate-co-4-hydroxybutyrate) (P3HB4HB) into PLA. The PLA/P3HB4HB blend films were prepared by varying compositions from 100/0 to 60/40 wt/wt and using compression molding. The investigations indicated that the PLA/P3HB4HB 90/10 blend film exhibits superior properties, such as synergistic toughness and increased %strain. Rice straw (RS) fiber is introduced as a reinforcing fiber in the blends, expanding …
Tarnish Resistance Of Silver Reinforced With Carbon Material To Artificial Sweat And Hydrogen Sulfide, Kunthida Chanthaban
Tarnish Resistance Of Silver Reinforced With Carbon Material To Artificial Sweat And Hydrogen Sulfide, Kunthida Chanthaban
Chulalongkorn University Theses and Dissertations (Chula ETD)
Due to its immense popularity, silver jewelry has undergone continual development, it an intriguing product. The most significant issue with silver jewelry is the tarnish of the silver metal's surface. Therefore, using a coin making technique, the study team evaluated the properties of silver metal reinforced by carbon materials. To evaluate the silver's to sweat and hydrogen sulfide tarnishing. Effects of adding carbon to samples after performing an artificial sweat test. It was discovered that the use of highly scattered carbon improved the ability to remove tarnish from fake sweat because it reduced the surface area of the silver (Ag) …
Activity And Stability Of Tio2-Encapsulated Cspbbr3/Cs4pbbr6 For Photocatalytic Degradation Of Rhodamine B, Nutzeya Plainoen
Activity And Stability Of Tio2-Encapsulated Cspbbr3/Cs4pbbr6 For Photocatalytic Degradation Of Rhodamine B, Nutzeya Plainoen
Chulalongkorn University Theses and Dissertations (Chula ETD)
Due to the excellent optoelectronic performance of cesium lead bromide(CsPbBr3), it has shown promising potential as a photocatalyst for the degradation of organic compounds under sunlight. During the synthesis of CsPbBr3, Cs4PbBr6, another formation of CsPbBr3, is also produced, which exhibits desirable properties such as strong and narrow photoluminescence (PL) and enhanced thermal stability. In this study, we successfully synthesized a mixture of CsPbBr3/Cs4PbBr6 nanoparticles using a simple precipitation method. However, the stability of CsPbBr3/Cs4PbBr6 was found to be sensitive to high temperatures, moisture, and oxygen, which could affect its photocatalytic degradation performance. To enhance both stability and activity, we …
Effect Of Type And Concentration Of Acid On Characteristics Of Functionalized Biochar And Its Performance In Converting Fructose To 5-Hmf, Pimlapas Bunwichian
Effect Of Type And Concentration Of Acid On Characteristics Of Functionalized Biochar And Its Performance In Converting Fructose To 5-Hmf, Pimlapas Bunwichian
Chulalongkorn University Theses and Dissertations (Chula ETD)
Biomass, with its high cellulosic content, represented renewable source capable of being converted into essential platform chemicals like 5-hydroxymethylfurfural, levulinic acid, formic acid, and furfural. Currently, conversion of fructose to 5-HMF was achievable through various acid homogeneous catalysts. Although these catalysts yield higher outputs, they might pose challenges in recycling and corrosion issues. This thesis's novel approach involved preparing heterogeneous catalysts through pyrolysis and hydrothermal treatment of watermelon rind to create watermelon rind biochar (WB). Subsequently, WB underwent functionalization using HCl, H2SO4, and H3PO4 at concentrations of 1.6, 3.2, and 4.8N, respectively, at temperatures of 150 °C. These treated WB …
Carboxymethyl Cellulose As Artificial Solid/Electrolyte Interphases And Separator For Zn-Based Battery, Phonnapha Tangthuam
Carboxymethyl Cellulose As Artificial Solid/Electrolyte Interphases And Separator For Zn-Based Battery, Phonnapha Tangthuam
Chulalongkorn University Theses and Dissertations (Chula ETD)
As the quest for robust large-scale energy storage systems (EESs) intensifies, aqueous rechargeable zinc-based batteries are gaining traction for grid-scale applications due to their high theoretical capacity and safety. Despite this, their practical application is compromised by several zinc anode issues, including hydrogen evolution, corrosion, dendritic growth, and passivation. An artificial solid electrolyte interphase (ASEI) using polyelectrolytes, such as carboxymethyl cellulose (CMC), is emerging as a solution, offering economic and environmental advantages. CMC's structure, enriched with carboxyl groups, allows for the refined management of zinc ion distribution at the electrode surface, promising enhanced surface stability. This study delves into CMC's …
A Comparative Study Of Sustainable Aviation Fuel Production From Hydroprocessing Process Between Hydrogen Recovery Unit From Steam Reforming And Hydrogen Generation Unit From Biomass Gasification, Praeva Pongsripipat
Chulalongkorn University Theses and Dissertations (Chula ETD)
Sustainable aviation fuel (SAF) can be generated using various processes. Among the well-established approaches, one that stands out is the hydrotreating of esters and fatty acids (HEFA). However, the HEFA process requires a source of hydrogen for the hydroprocessing reactions. Hydrogen is often considered as an expensive component, and its cost can have a significant impact on the overall economic viability of renewable aviation fuel production. In this work, the SAF process is developed using Aspen Plus simulation. There are 2 scenarios to be considered. Scenario 1 involves a plant in which the hydrotreating of palm oil is performed to …
Effect Of Dispersion Of Carbon Nanotubes On Electrical Conductivity And Compressive Strength Of Cnt/Cement Composite, Rittikiat Wandaw
Effect Of Dispersion Of Carbon Nanotubes On Electrical Conductivity And Compressive Strength Of Cnt/Cement Composite, Rittikiat Wandaw
Chulalongkorn University Theses and Dissertations (Chula ETD)
Carbon nanotubes (CNTs) are promising nanomaterials due to their exceptional properties, including high electrical, mechanical, and stability characteristics. These advantageous features position CNTs as suitable candidates for diverse applications, particularly in additive formulations designed to enhance overall performance. One notable application is their use in cement composites to improve mechanical and electrical properties. However, the hydrophobic property of CNTs presents challenges for dispersion within the hydrophilic cement matrix. Consequently, methods have been developed to aid CNT dispersion in both water and cement matrices. In this thesis, Triton X-100 employed as a surfactant, was used to disperse CNTs in water using …
Photoelectrochemical Oxidation Of Benzyl Alcohol In A Continuous-Flow Microchannel Reactor Using Titanium Dioxide Photoanode, Sirachat Sattayarak
Photoelectrochemical Oxidation Of Benzyl Alcohol In A Continuous-Flow Microchannel Reactor Using Titanium Dioxide Photoanode, Sirachat Sattayarak
Chulalongkorn University Theses and Dissertations (Chula ETD)
Fossil fuel, a primary energy source of humans, emits carbon dioxide and other greenhouse gases which have a high impact on the environment. Renewable energy development has been promised to solve the problem. Solar light, a renewable energy with an unlimited energy source, has gained attention to develop in various applications including energy production and catalytic chemical reactions. The photoelectrochemical process is a chemical catalysis technique that combines electrochemical and photocatalysis and has an advantage of low energy consumption due to solar energy support. In this work, the continuous-flow photoelectrochemical reactor was fabricated to undergo the oxidation reaction of benzyl …
Transformation Graphene Quantum Dot Structure On Ag Electrodes Under Electrochemical Reduction, Sivakorn Bovornsintuchon
Transformation Graphene Quantum Dot Structure On Ag Electrodes Under Electrochemical Reduction, Sivakorn Bovornsintuchon
Chulalongkorn University Theses and Dissertations (Chula ETD)
In this study, we investigated the effect of electrochemical reduction time on the characteristicsstructural changes of various GQDs on Ag/Cu electrode was investigated. The GQDs were derived from three precursors including materials: Acetic, Glycine, and Bicarbonate were treated under electrochemical reduction conditions for , with reaction times of 15, 30, 45, and 60 minutes respectively. The obtained sSamples from each time period were then tested for their applicability in graphene screen-printed carbon electrodes using cyclic voltammetry techniques. The cyclic voltammetry test results revealed that among all the samples, those derived from Blue CL-GQDs #Acetic at 15 minutes and 60 minutes …
Techno-Economic Analysis Of Acetone And Ethylene Production From Bioethanol, Thanyarath Nueangchamnong
Techno-Economic Analysis Of Acetone And Ethylene Production From Bioethanol, Thanyarath Nueangchamnong
Chulalongkorn University Theses and Dissertations (Chula ETD)
Bioethanol is primarily blended with gasoline to produce "gasohol." This blend not only reduces dependence on fossil fuels but also cuts down on crude oil imports and bolsters the agricultural sector by creating a market for crops and their residues. Currently, Thailand is witnessing a growing trend towards electric vehicles (EVs). This trend is largely driven by government subsidies for domestic EV manufacturing and plans by overseas companies to establish manufacturing bases within the country. As a result, the bioethanol industry in Thailand is grappling with challenges, chief among them being the decreasing demand for its product. Nonetheless, any bioethanol …
ผลกระทบของวิธีการสร้างภาพเอกซเรย์ต่อความถูกต้องของ ค่าความหนาแน่นอิเล็กตรอนและเลขอะตอมยังผลจาก เครื่องเอกซเรย์คอมพิวเตอร์จำลองการรักษาแบบสองพลังงาน, เกตุนภาพร เกตุประดิษฐ์
ผลกระทบของวิธีการสร้างภาพเอกซเรย์ต่อความถูกต้องของ ค่าความหนาแน่นอิเล็กตรอนและเลขอะตอมยังผลจาก เครื่องเอกซเรย์คอมพิวเตอร์จำลองการรักษาแบบสองพลังงาน, เกตุนภาพร เกตุประดิษฐ์
Chulalongkorn University Theses and Dissertations (Chula ETD)
ในระยะไม่กี่ปีที่ผ่านมา มีการพัฒนาเครื่องเอกซเรย์คอมพิวเตอร์ในหลายรูปแบบ หนึ่งในนั้นได้แก่เครื่องเอกซเรย์คอมพิวเตอร์แบบสองพลังงาน (Dual-Energy Computed Tomography) ซึ่งมีความแม่นยำในการประมาณค่าความหนาแน่นอิเล็กตรอนและค่าเลขอะตอมยังผล ทั้งสองค่านี้มีความสำคัญในด้านรังสีรักษาเป็นส่วนบ่งบอกคุณลักษณะของเนื้อเยื่อ งานวิจัยนี้มีจุดประสงค์เพื่อศึกษาความถูกต้องของการคำนวณค่าความหนาแน่นอิเล็กตรอนและค่าเลขอะตอมยังผลจากภาพที่ประมวลผลด้วย Iterative reconstruction algorithm วิธีการทดลอง ขั้นตอนแรกจะสร้างหุ่นจำลองดิจิตอลโดยใช้โปรแกรม MATLAB R2021a อ้างอิงลักษณะเนื้อเยื่อจากหุ่นจำลอง GAMMEX 467 โดยมีประเภทเนื้อเยื่อดังต่อไปนี้ เนื้อเยื่อกระดูกชนิดเนื้อแน่น (Cortical bone) เนื้อเยื่อสมอง (Brain) เนื้อเยื่อไขมัน (Adipose) และเนื้อเยื่อเต้านม (Breast) ขั้นตอนที่สองสร้างซิโนแกรม (sinogram) โดยจำลองพลังงานของรังสีเอกซ์จากเครื่องเอกซเรย์คอมพิวเตอร์แบบสองพลังงานที่พลังงาน 80 และ 140 kVp โดยใช้ SPEKTR 3.0 MATLAB Toolbox ให้พลังงานทั้งสองผ่านหุ่นจำลองดิจิตอลที่สร้างขึ้นมา เก็บมุมของภาพทั้งหมด 180 มุม ขั้นตอนที่สามเพิ่มสัญญาณรบกวนลงในภาพซิโนแกรมโดยตั้งค่าการกระจายสัญญาณรบกวน 3 ระดับได้แก่ 2, 5 และ 10 ขั้นตอนที่สี่ทำการประมวลผลสร้างภาพตัดขวางจากภาพซิโนแกรมที่ไม่มีสัญญาณรบกวนและมีสัญญาณรบกวนในระดับต่างๆ ด้วยวิธีการฉายภาพย้อนกลับแบบกรอง (Filtered back projection) และวิธีการวนซํ้า (iterative algorithm) โดยใช้ TIGRE Toolbox แล้วคำนวณหาค่าความหนาแน่นอิเล็กตรอนและค่าเลขอะตอมยังผลจากภาพที่ประมวลผลได้โดยใช้สมการ DEEDZ ผลการวิจัยพบว่าวิธีการประมวลผลแบบวิธีการวนซํ้า ให้ค่าความหนาแน่นอิเล็กตรอนจากภาพซิโนแกรมที่ไม่มีสัญญาณรบกวนและที่มีสัญญาณรบกวนในระดับต่างๆในเนื้อเยื่อทุกประเภทดีกว่าวิธีการฉายภาพย้อนกลับแบบกรอง ยกเว้น ภาพซิโนแกรมที่ไม่มีสัญญาณรบกวนในเนื้อเยื่อกระดูกชนิดเนื้อแน่นเมื่อเปรียบเทียบกับค่าความหนาแน่นอิเล็กตรอนมาตรฐาน ผลการวิจัยในส่วนค่าเลขอะตอมยังผลพบว่าวิธีการประมวลผลแบบวิธีการวนซํ้าให้ค่าเลขอะตอมยังผลจากภาพซิโนแกรมที่ไม่มีสัญญาณรบกวนและที่มีสัญญาณรบกวนในระดับต่างๆในเนื้อเยื่อทุกประเภทดีกว่าวิธีการฉายภาพย้อนกลับแบบกรองเมื่อเปรียบเทียบกับค่าเลขอะตอมยังผลมาตรฐาน
การศึกษาเปรียบเทียบตัวเร่งปฏิกิริยาโมลิบดีนัมบนแร่ดินขาวที่ต่างกันเพื่อใช้ในปฏิกิริยาการขจัดน้ำของเอทานอลไปเป็นเอทิลีน, ณัฐธิดา ห่างภัย
การศึกษาเปรียบเทียบตัวเร่งปฏิกิริยาโมลิบดีนัมบนแร่ดินขาวที่ต่างกันเพื่อใช้ในปฏิกิริยาการขจัดน้ำของเอทานอลไปเป็นเอทิลีน, ณัฐธิดา ห่างภัย
Chulalongkorn University Theses and Dissertations (Chula ETD)
งานวิจัยนี้เป็นการศึกษาเปรียบเทียบตัวเร่งปฏิกิริยาโมลิบดีนัมบนแร่ดินขาวที่ต่างกันเพื่อใช้ในปฏิกิริยาการขจัดน้ำของเอทานอลไปเป็นเอทิลีนทั้งหมด 3 ชนิด ได้แก่ เคโอลิไนต์ มอนต์มอริลโลไนต์และอะลูมินัม พิลลาร์ มอนต์มอริลโลไนต์ โดยมีการใส่โมลิบดีนัมลงไปในตัวเร่งปฏิกิริยาให้มีความปริมาณของโมลิบดีนัมเปอร์เซ็นต์โดยน้ำหนักที่ต่าง คือ 2 5 และ 10 ซึ่งสามารถอภิปรายผลจากการวิเคราะห์ได้ว่า ปฏิกิริยาการขจัดน้ำด้วยเอทานอลไปเป็นเอทิลีน ที่อุณหภูมิประมาณ 200 ถึง 250 องศาเซลเซียส ได้ผลิตภัณฑ์หลักเป็นไดเอทิลอีเทอร์ และ อะซีตัลดีไฮด์ และที่อุณหภูมิประมาณ 300 ถึง 400 องศาเซลเซียสได้ผลิตภัณฑ์หลักเป็นเอทิลีน กลุ่มของตัวเร่งปฏิกิริยาในกลุ่มตัวรองรับเคโอลิไนต์ เมื่อมีการปรับปรุงด้วยโมลิบดีนัมทำให้พื้นที่ผิวนั้นมีค่าลดลง แต่ความเป็นกรดนั้นสูงขึ้น ส่งผลให้ร้อยละการใช้ของเอทานอลและร้อยละผลได้ของผลิตภัณฑ์เอทิลีนเพิ่มขึ้นขาก 42.9 และ 10.0 เป็น 57.4 และ 44.2 ตามลำดับ ที่ปริมาณโมลิบดีนัม 10 เปอร์เซ็นต์โดยน้ำหนัก ส่วนของกลุ่มตัวเร่งปฏิกิริยากลุ่มรองรับมอนต์มอริลโลไนต์ซึ่งมีพื้นผิวที่สูง และความเป็นกรดที่สูง เมื่อมีการปรับปรุงด้วยโมลิบดีนัมแล้วทำให้ค่าความเป็นกรดเพิ่ม ทำให้ร้อยละการใช้ของเอทานอลและร้อยละผลได้ของผลิตภัณฑ์เอทิลีนปริมาณสูงสุดอยู่ที่ปริมาณโมลิบดีนัมที่ 10 เปอร์เซ็นต์โดยน้ำหนักอยู่ที่ 96.8 และ 89.1 เพิ่มขึ้นเป็น 99.4 และ 86.8 ตามลำดับ และในกลุ่มตัวเร่งปฏิกิริยาตัวรองรับอะลูมินัม พิลลาร์ มอนต์มอริลโลไนต์เดิมทีตัวเร่งปฎิกิริยารองรับอะลูมินัม พิลลาร์ มอนต์มอริลโลไนต์มีค่าความเป็นกรดที่อยู่ระดับที่ดีอยู่แล้ว เมื่อมีการปรับปรุงด้วยโมลิบดีนัมแล้วไม่เป็นผลดีต่อการเพิ่มค่าคอนเวอร์ชันของเอทานอลและค่าการเลือกเกิดของเอทิลีน และจากการศึกษาการเปรียบเทียบการเสื่อมสภาพของตัวเร่งปฏิกิริยาพบว่าตัวเร่งปฏิกิริยาที่ถูกปรับปรุงด้วยโมลิบดีนัมเกิดการเสื่อมภาพของตัวเร่งปฏิกิริยามากกว่าตัวเร่งปฏิกิริยาที่ยังไม่ถูกปรับปรุงด้วยโมลิบดีนัม
การดูดซับสีย้อมรีแอคทีฟแบล็ค 5 โดยถ่านกัมมันต์จาก กากกาแฟ, ธวัชชัย คุลบุตร
การดูดซับสีย้อมรีแอคทีฟแบล็ค 5 โดยถ่านกัมมันต์จาก กากกาแฟ, ธวัชชัย คุลบุตร
Chulalongkorn University Theses and Dissertations (Chula ETD)
ในงานวิจัยนี้ศึกษาการนำกากกาแฟมาใช้เป็นวัสดุตั้งต้นในการสังเคราะห์เป็นถ่านกัมมันต์ เพื่อใช้สำหรับการกำจัดสีย้อมรีแอคทีฟแบล็ค 5 ผ่านกระบวนการดูดซับทั้งแบบกะและแบบคอลัมน์ ถ่านกัมมันต์สังเคราะห์โดยนำสารละลายซิงค์คลอไรด์มาตรึงรูปบนกากกาแฟจากนั้นนำไปผ่านกระบวนการคาร์บอไนเซชันภายใต้บรรยากาศไนโตรเจน พบว่าถ่านกัมมันต์ที่ได้จากกากกาแฟโรงงานอุตสาหกรรมผลิตกาแฟสำเร็จรูปซึ่งผ่านการคาร์บอไนเซชันที่อุณหภูมิ 600°C และกระตุ้นในอัตราส่วนมวลของกากกาแฟต่อซิงค์คลอไรด์เกรดงานวิเคราะห์ 1:3 (Z3-IC600) ให้พื้นที่ผิวจำเพาะ (SBET = 1260.39 m2/g) และปริมาตรรูพรุนมีโซพอร์ (Vmeso= 1.03 cm3/g) จำนวนมาก เมื่อเทียบกับถ่านที่ได้จากกากกาแฟที่ไม่กระตุ้นด้วยซิงค์คลอไรด์ ซึ่งมีพื้นที่ผิวจำเพาะ 31.82 m2/g และปริมาตรรูพรุนรวมเท่ากับ 0.04 cm3/g โดยการมีอยู่ของรูพรุนชนิดมีโซพอร์ของตัวอย่าง (Z3-IC600) ส่งผลให้มีค่าการดูดซับสีย้อมรีแอคทีฟแบล็ค 5 แบบกะสูงสุดตามแบบจำลองแลงเมียร์ (qm) เท่ากับ 120.39 mg/g และสำหรับการดูดซับแบบคอลัมน์ ถ่านกัมมันต์ที่กระตุ้นในอัตราส่วนมวลของกากกาแฟต่อซิงค์คลอไรด์เกรดอุตสาหกรรม 1:3 และอุณหภูมิคาร์บอไนเซชัน 600°C ถูกเลือกใช้เป็นวัสดุดูดซับ เพราะสารเคมีซิงค์คลอไรด์เกรดอุตสาหกรรมมีราคาถูกกว่าเกรดงานวิเคราะห์อย่างมาก และให้สมบัติความเป็นรูพรุนของถ่านกัมมันต์และค่าการดูดซับสีย้อมรีแอคทีฟแบล็ค 5 แบบกะ ใกล้เคียงกับการกระตุ้นด้วยซิงค์คลอไรด์เกรดงานวิเคราะห์ (SBET = 1225.39 m2/g, Vmeso= 0.92 cm3/g และ qm = 113.01 mg/g) ซึ่งวัสดุดูดซับดังกล่าวมีค่าการดูดซับสีย้อมรีแอคทีฟแบล็ค 5 แบบคอลัมน์ ณ จุดอิ่มตัว (qe) เท่ากับ 60.40 mg/g ที่ความเข้มข้นเริ่มต้น 100 mg/L อัตราการไหล 10 mL/min และความสูงของเบดนิ่ง 5 cm โดยทั้งหมดทดลองภายใต้ pH ที่เป็นกลาง