Chemical Engineering Commons^™

Membrane-Based Removal Of Ammonia From A Waste Stream And Its Recovery, Philip A. Aligwe

Dissertations

At neutral pH levels, ammonia in aqueous streams exists in two forms: ammonium ion (NH₄⁺) and dissolved ammonia gas molecules (NH₃). Membrane separation serves as a viable option for treatment of ammonia containing effluents. This can be achieved via by stripping NH₃ from an ammonia feed solution at feed solution pH > 11 via hollow fiber supported gas membrane (SGM) or removing NH₄⁺ from an ammonia feed solution at feed solution pH < 7 via liquid or polymeric membranes.

The first study reported here examines the influence of feed volumetric flow rates on outlet NH₃ concentrations in parallel flow …

Graphene Based Barrier Membrane For Gas Separation Processes, Cheng Peng

Dissertations

Novel graphene oxide (GO) flake-based composite lamellar membrane structure is being developed as a potential component of a garment for protection against chemical warfare agents (CWAs) represented here by simulants, dimethyl methyl phosphonate (DMMP) (a sarin-simulant) and 2-chloroethyl ethyl sulfide (2-CEES) (a simulant for sulfur mustard), yet allowing a high moisture transmission rate. GO flakes of dimensions 300-800 nm, 0.7-1.2 nm thickness and dispersed in an aqueous suspension are formed into a membrane by vacuum filtration on a porous polyethersulfone (PES) or poly (ether-ether-ketone) (PEEK) support membrane for noncovalent π-π interactions with GO flakes. After physical compression of such a …

Moisture Permeable Barrier Membranes For Toxic Gases And Vapors, Yufeng Song

Dissertations

Defense against small molecule toxic gases is an important aspect of protection against chemical and biological threat as well as chemical releases from industrial accidents. Current protective respirators/garments cannot effectively block small molecule toxic gases and vapors and retain moisture transmission capability without a heavy burden.

Metal organic frameworks (MOFs) have been used as highly effective adsorbents and catalysts to remove ammonia, cyanogen chloride, and sulfur dioxide from air. A nanopacked bed of nanoparticles of MOF by synthesizing them in the pores of microporous membranes is developed in the study. The submicron scale size of membrane pores ensures a large …

Stress-State And Injection-Rate Dependent Damage Processes During The Hydraulic Fracturing Of Granite, Gayani Sasendrika Gunarathna

Dissertations

Hydraulic fracturing is a well-stimulation technique that is employed in field applications, such as enhanced geothermal systems (EGS) and shale oil/gas extraction. This research experimentally investigates the effect of the state of stress and injection rate on the hydraulic fracturing processes. In addition, a displacement discontinuity method (DDM) code, FROCK, is used to model the crack initiation and propagation in a granite specimen under hydraulic fracturing conditions. In order to conduct the experimental work, a test setup capable of applying a triaxial state of stress and water pressure inside pre-fabricated flaws cut in prismatic granite specimens is developed. Additionally, the …

Calculating Elastic Properties Of Confined Simple Fluids, Christopher D. Dobrzanski

Dissertations

Confinement in nanoporous materials is known to affect many properties of the fluids confined within their pores. The elastic properties are no exception. This dissertation begins with an overview of the relevant literature on ways of obtaining elastic properties of confined fluids. It outlines some fundamental gaps in our understanding. The chapters following address some of these gaps in understanding elastic properties of the confined fluid, in particular, how the shape of the confining pore matters, how supercriticality effects the properties, how an equation of state designed for confined fluids can be used to calculate elastic properties, and if an …

Particle Engineering Via Surface Modification: Model Based Analysis, Kai Zheng

Dissertations

Size reduction, an important step in particle engineering, leads to downstream processing problems because of fine powders are cohesive. This research aims to improve the fine particle properties through surface modification and develop better understanding of such processes by model-based analysis. Four case studies concerning surface modification are systematically investigated.

First, enhancement of dissolution behavior of griseofulvin is investigated via combination of amorphization and particle size reduction. The dissolution behavior is affected by the particle size and polymer loading. Finest size amorphous solid dispersions dissolve fast enough to negate the higher recrystallization rate and enhance drug loading by reducing the …

Che 472-Hm2: Process And Plant Design Honors, Nellone Reid

Chemical and Materials Engineering Syllabi

No abstract provided.

Customized Boron And Magnesium-Based Reactive Materials Prepared By High Energy Mechanical Milling, Xinhang Liu

Dissertations

New reactive materials need to be developed having biocidal combustion products. When ignited, such material can add chemical biocidal effects to the common effects of high temperature and pressure. Biocidal combustion products are capable of deactivating harmful spores or bacteria, which can be released by targets containing biological weapons of mass destruction. Research showed that halogens, especially iodine, are effective as biocidal components of reactive material formulations. Recently, magnesium combustion product MgO is also found to have a biocidal effect. Thus, advanced formulations containing both magnesium and iodine are of interest; such formulations are prepared and investigated here.

Reactive materials …

Impact Of Stirrer Speed And Media Type-Loading On The Breakage Kinetics During Wet Stirred Media Milling Of Griseofulvin, Nathaniel Parker

Theses

The aim of this study is to investigate the impact of stirrer speed (2000-4000 rpm) and bead loading (~20-60%) on the breakage kinetics-energy consumption during milling of griseofulvin, a poorly soluble drug, and compare the performance of crosslinked polystyrene (CPS) beads with that of yttrium-stabilized zirconia (YSZ) beads. Laser diffraction, SEM, viscometry, and XRPD were used for characterization. A microhydrodynamic model was used to interpret the breakage kinetics. An increase in stirrer speed led to faster breakage due to more frequent and forceful CPS bead-bead collisions. Despite causing slight decrease in maximum contact pressure, an increase in CPS bead loading …

Effect Of 3d Printed Tablet Shape On Drug Release Profile, Christina Gedeon

Theses

There is a growing interest in utilizing additive manufacturing (AM) as a manufacturing tool to develop oral tablets for personalized medicine. This ultimate goal in mind, this study explores the feasibility of extrusion-based fused deposition modeling (FDM) to 3D print oral tablets with tunable design to control drug release profile. Tablets are printed using poly(vinyl alcohol) (PVA) loaded with model drugs: acetaminophen and caffeine. Hot melt extrusion (HME) is used to fabricate PVA filaments loaded with acetaminophen and caffeine. These filaments are used to fabricate a range of tablets with varying designs to prepare immediate and delayed release tablets. Thermal …

Modelling In Vitro Dissolution And Release Of Sumatriptan Succinate From Polyvinylpyrrolidone-Based Microneedles Aided By Iontophoresis, James Paul Ronnander

Dissertations

A novel dissolving microneedle array system is developed to investigate permeation of a sumatriptan succinate formulations through the skin aided by iontophoresis. Three formulations consisting of hydrophilic, positively charged drug molecules encapsulated in a water-soluble biologically suitable polymer, polyvinylpyrrolidone (PVP), have been accepted by the U.S. Food and Drug Administration (FDA). The microneedle systems are fabricated with 600 pyramid-shaped needles, each 500 µm tall, on a 0.785-cm² circular array. In vitro transdermal studies with minipig skin and vertical Franz diffusion cells show > 68% permeation of sumatriptan over a 24-hour period. A combination of microneedle and electrical current density ranging …

Improving Boron For Combustion Applications, Kerri-Lee Annique Chintersingh

Dissertations

Boron has received much attention as a potential additive to explosives and propellants due to its high theoretical gravimetric and volumetric heating values. The challenge, however, is that boron particles tend to agglomerate, have lengthy ignition delays and very low combustion rates. Prior research indicates that boron’s long ignition delays are due to its inhibiting naturally occurring oxide layer, impeding the diffusion of reactants for oxidation. For combustion, current studies report that boron particles have two consecutive stages, but the actual reaction mechanism is poorly understood. Despite many years of relevant research, quantitative combustion data on micron-sized boron particles are …

Analyzing Evolution Of Rare Events Through Social Media Data, Xiaoyu Lu

Dissertations

Recently, some researchers have attempted to find a relationship between the evolution of rare events and temporal-spatial patterns of social media activities. Their studies verify that the relationship exists in both time and spatial domains. However, few of those studies can accurately deduce a time point when social media activities are most highly affected by a rare event because producing an accurate temporal pattern of social media during the evolution of a rare event is very difficult. This work expands the current studies along three directions. Firstly, we focus on the intensity of information volume and propose an innovative clustering …

Roles Of Surfactant And Binary Polymers On Dissolution Enhancement Of Bcs Ii Drugs From Nanocomposites And Amorphous Solid Dispersions, Md Mahbubur Rahman

Dissertations

Drug nanocomposites and amorphous solid dispersions (ASDs) are two major formulation platforms used for the bioavailability enhancement of BCS Class II drugs. The major drawback of nanocomposites is their inability to attain high drug supersaturation during in vitro (<50% relative supersaturation) and in vivo dissolution. On the other hand, formulating an amorphous solid dispersion (ASD) with high drug loading (>20%) that releases drug rapidly, while generating and maintaining high supersaturation over at least three hours is challenging. The goal of this thesis is to develop a fundamental understanding of the impact of anionic surfactants–polymers on in vitro drug release from nanocomposites and ASDs, while addressing the above challenges. To achieve this goal, the following objectives are set: (1) compare griseofulvin …

Enzymatic Biofuel Cells In A Sandwich Geometry With Compressed Carbon Nanotubes/Enzyme Electrodes & Hybrid Patch Applications, Biao Leng

Dissertations

Enzymatic biofuel cells (EBFCs) convert the chemical energy of biofuels, such as glucose and methanol, into electrical energy by employing enzymes as catalysts. In contrast to conventional fuel cells, EBFCs have a simple membrane-free fuel cell design due to the high catalytic specificity of the enzymes, but the power densities obtained are lower. Although the primary goal of research on EBFCs has been to develop a sustainable power source that can be directly implanted in the human body to power bio-devices, other applications such as the use of a flexible film or fuel cell patch as a wearable power source …

Electrochemically Reactive Membranes For Efficient Biomass Recovery, Pollutant Degradation And Commercialization, Likun Hua

Dissertations

Micropollution in natural waters such as rivers and groundwater aquifers is a widespread problem that prevents these potentially potable sources from being used as drinking water. In the United States, approximately two-thirds of the over 1,200 most serious hazardous waste sites in the nation are contaminated with trichloroethylene (TCE), a potentially carcinogenic compound. Other emerging and environmentally persistent organic micropollutants include polyromantic hydrocarbons (PAHs), organophosphate flame retardants, endocrine disrupting compounds (EDCs), pesticides, herbicides, pharmaceuticals and personal care products (PPCPs). Membrane filtration is one of the most efficient separation processes widely used for water treatment and pollutant removal. However, traditional membrane …

Speciation Of Gaseous Oxidized Mercury Molecules Relevant To Atmospheric And Combustion Environments, Francisco J. Guzman

Dissertations

Mercury is a pervasive and highly toxic environmental pollutant. Major anthropogenic sources of mercury emissions include artisanal gold mining, cement production, and combustion of coal. These sources release mostly gaseous elemental mercury (GEM), which upon entering the atmosphere can travel long distances before depositing to environmental waters and landforms. The deposition of GEM is relatively slow, but becomes greatly accelerated when GEM is converted to gaseous oxidized mercury (GOM) because the latter has significantly higher water solubility and lower volatility. Modeling GOM deposition requires the knowledge of its molecular identities, which are poorly known because ultra-trace (tens to hundreds part …

N8- Polynitrogen Stabilized On Carbon-Based Supports As Metal-Free Electrocatalyst For Oxygen Reduction Reaction In Fuel Cells, Zhenhua Yao

Dissertations

The sluggish oxygen reduction reaction (ORR) kinetics at the cathode is one of the key factors limiting the performance of polymer electrolyte membrane fuel cell (PEMFC). Platinum-based materials are the most widely studied catalysts for this ORR reaction while their large-scale practical application in fuel cells is hindered due to their scarcity and low stability. Therefore, highly active, low cost and robust non-Pt catalysts are being developed to overcome the drawbacks. Recently, a novel polynitrogen N8- (PN) stabilized on multiwall carbon nanotube (MWNT) was synthesized under ambient condition for the first time by our group and demonstrated high ORR activities. …

Engineered Excipients Via Dry Particle Coating, Liang Chen

Dissertations

Excipients with good flowability, bulk density as well as compaction properties are desired for use in tableting since they play important roles in formulation development and processing, including, handling, mixing, feeding and compaction. However, it is often difficult to manufacture excipients that simultaneously possess all three desirable properties, particularly if their size is fine. In addition, it is desirable that the excipients promote direct compression of poorly compactable fine cohesive drug powders at sufficiently high drug loading, and not just achieve the desired high functional properties in placebo formulations. This dissertation aims to developed engineered excipients towards this unmet industry …

Enzyme-Assisted Development Of Hydrogels As Medical Materials With Injectable, Biodegradable And Biocompatible Properties, Yung-Hao Tsou

Dissertations

Hydrogels were first discovered in the year 1960 by Wichterle and Lim [1], and in the following decades, they have been widely studied because of their unique characteristics including their hydrophilic nature, biocompatibility, and capacity to mimic the extracellular matrix (ECM). Hydrogels based on natural or synthetic polymers have continued to be of interest for tissue engineering and drug delivery due to their ability to encapsulate living cells and control the release rate of drugs or other bioactive molecules such as pharmaceutical proteins.

In the first part of this dissertation, dopant-free photoluminescent hydrogels formed in situ by crosslinking of biocompatible …

The Use Of Electrical Resistance Tomography To Determine The Minimum Agitation Speed For Solids Suspension In Stirred Tank Reactors, Baran Teoman

Theses

Njs, the minimum agitation speed needed to just suspend all the solid particles in a solid-liquid mixture stirred in an agitated vessel, is a critical parameter to properly operate industrial tanks in a large number of industrial operations. As a result, a significant literature on Njs is available. The oldest and the most common method to measure Njs experimentally is that of Zwietering’s (Chem. Eng. Sci., 1958, 8, 244-253), where Njs can be visually obtained by determining when the solids stay at the bottom of the tank for no more than 1-2 seconds before being swept away. Although this has …

Glass Transition Temperature Of Particles For Drug Delivery, Yiqing Yang

Theses

Drug delivery plays an important role in targeted therapies and nanoparticles which can be used as drug carriers and it’s a frequently researched topic. Poly(lactic-co-glycolic acid) (PLGA), a highly biocompatible polymer, has been used as a drug delivery vehicle in many studies. One of the challenges facing drug delivery particles is the problem of burst release which is when a large amount of the drug is suddenly released from the particle once it is placed in the body. This is generally undesirable as usually a slow and controlled release is preferred. The glass transition temperature has an effect on drug …

The Cooperative Effects Of Channel Length-Bias, Width Asymmetry, Gradient Steepness, And Contact-Guidance On Fibroblasts’ Directional Decision Making, Quang Long Pham

Dissertations

Cell migration in complex micro-environments, that are similar to tissue pores, is important for predicting locations of tissue nucleation and optimizing scaffold architectures. Firstly, how fibroblast cells - relevant to tissue engineering, affect each other’s directional decisions when encountered with a bifurcation of different channel lengths was investigated. It was found that cell sequence and cell mitosis influence the directional choices that the cells made while chemotaxing. Specifically, the fibroblasts chose to alternate between two possible paths - one longer and the other shorter - at a bifurcation. This finding was counter-intuitive given that the shorter path had a steeper …

Experimental And Numerical Characterization Of Multiphase Subsurface Oil Release, Feng Gao

Dissertations

Subsurface oil release is commonly encountered in the natural environment and engineering applications and has received the substantial attention of researchers after the disastrous Deepwater Horizon Blowout oil spill in 2009. The main focus on the present research is to systematically study the hydrodynamics of underwater oil jet under a variety of conditions, including the effect of dispersant and different gas to oil ratios (GOR) by using experimental measurement as well as a Computational Fluid Dynamics (CFD) approach, from which the measured turbulent characteristics (e.g., velocity, turbulent kinetic energy, turbulence dissipation rate, etc.) of underwater oil jet are thoroughly examined …

Overcoming Conventional Modeling Limitations Using Image- Driven Lattice-Boltzmann Method Simulations For Biophysical Applications, Olufemi E. Kadri

Dissertations

The challenges involved in modeling biological systems are significant and push the boundaries of conventional modeling. This is because biological systems are distinctly complex, and their emergent properties are results of the interplay of numerous components/processes. Unfortunately, conventional modeling approaches are often limited by their inability to capture all these complexities. By using in vivo data derived from biomedical imaging, image-based modeling is able to overcome this limitation.

In this work, a combination of imaging data with the Lattice-Boltzmann Method for computational fluid dynamics (CFD) is applied to tissue engineering and thrombogenesis. Using this approach, some of the unanswered questions …

Interactions Between Polymer Nanoparticles And Blood Plasma Applied To Drug Delivery Systems, Mark Bannon

Theses

Targeted nanoparticle drug delivery has the potential to replace current forms of cancer therapy with previously unparalleled efficiency. Upon introduction into the human body, nanoparticles exhibit a substantial increase in diameter due to a biomolecular corona formation caused by interactions between blood plasma proteins and the nanoparticles. These interactions must be analyzed and understood for targeted delivery to reach its potential in both feasibility and efficiency.

To study the formation of the protein corona, polystyrene nanoparticles were incubated in vitro in goat blood plasma for 10-minute intervals, diluted to different degrees and then measured to obtain the hydrodynamic diameter of …

Mechanochemical Nitration Of Aromatic Compounds, Oleg Shlomo Lagoviyer

Theses

Aromatic compounds such as toluene are commercially nitrated using a combination of nitric acid with other strong acids. This process relies on the use of highly corrosive chemicals and generates environmentally harmful waste, which is difficult to handle and dispose of. In this study aromatic nitration using solvent-free mechanochemical processing of environmentally benign precursors has been achieved and investigated. Mononitrotoluene was synthesized by milling toluene with sodium nitrate and molybdenum trioxide as a catalyst. Several parameters affecting the desired product yield and selectivity were identified and varied. MNT yields in excess of 60% have been achieved in different tests. The …

Micronized Dry Drug Powder-Loaded Polymer Films For Delivery Of Poorly Water Soluble Drugs, Lu Zhang

Dissertations

Polymer strip films have been recently established as a robust platform for delivery of poorly water-soluble drugs via slurry casting, in particular using stable drug nanosuspensions. In this dissertation, a simpler, economically feasible, and robust method to directly incorporate dry micronized poorly water-soluble drug is introduced. As a major novelty, simultaneous surface modification using hydrophilic silica along with micronization is done using fluid energy mill (FEM) in order to reduce the hydrophobicity and agglomeration of poorly water-solube drug powder. When micronized coated drug powders are used, films exhibit improved appearance (thickness uniformity, visible lumps), better drug content uniformity (relative standard …

Combustion Of Nanocomposite Thermite Powders, Ian Monk

Dissertations

This work investigates combustion of nanocomposite thermite powders prepared by arrested reactive milling (ARM). The focus is on how ARM as a top-down approach to nano-thermite building generating fully-dense nanocomposite particles with dimensions of 1-100 µm affects the rates and mechanism of their combustion. A variety of thermites are milled using both aluminum and zirconium as fuels combined with several oxidizers (WoO₃, MoO₃, CuO, Fe₂O₃, and Bi₂O₃). The powders are ignited using both an electrostatic discharge (ESD) and a CO₂ laser beam.

A range of parameters vary …

Computational And Experimental Determination Of The Mixing Efficiency Of A Microfluidic Serpentine Micromixer, Siril Arockiam

Theses

In microfluidics, efficiency and mixing time are the greatest disadvantages. These parameters hinder the application of microfluidic devices for biochemical and immunological assays. However, once these disadvantages have been overcome by optimizing the parameters of the microfluidic device, it becomes the important analytical tool. In this experiment, various designs of microfluidic devices have been both simulated using COMSOL software, and experimentally verified to obtain the optimized parameter such as depth and velocity for better mixing efficiency. The COMSOL model has been validated by comparing the results with fluorescent images data of the experiment. The microfluidic device is built with Adhesive …