Chemical Engineering Commons^™

Hydrodynamic Investigation Of The Discharge Of Complex Fluids From Dispensing Bottles Using Experimental And Computational Approaches, Baran Teoman

Dissertations

The discharge of non-Newtonian, complex fluids through orifices of industrial tanks, pipes, dispensers, or packaging containers is a ubiquitous but often problematic process because of the complex rheology of such fluids and the geometry of the containers. This, in turn, reduces the discharge rate and results in residual fluid left in the container, often referred to as heel. Heel formation is undesired in general, since it causes loss of valuable material, container fouling, and cross-contamination between batches. Heel may be of significant concern not only in industrial vessels but also in consumer packaging. Despite its relevance, the research in this …

Microhydrodynamic, Kinetic And Thermal Modeling Of Wet Media Milling For Process Optimization And Intensification, Gulenay Guner

Dissertations

Nanoparticle production by wet stirred media milling (WSMM) is a common method for the formulation of poorly water-soluble drugs. While most of the studies in the WSMM literature focus on the formulation aspects to overcome the stability challenges, a thorough mechanistic understanding of the process is lacking, and the process is slow, costly, and energy-intensive. This dissertation presents experimental and modeling work with the ultimate goals of (i) gaining a deeper and more mechanistic understanding of the WSMM process and breakage kinetics of the particles using a microhydrodynamic model with various improvements and advancements, (ii) examining the heat dissipation during …

A Novel Biomaterial Platform For Cardiac Tissue Engineering, Andrew House

Dissertations

Heart disease is one of the leading causes of death in the world. With a growing demand for in vitro cardiac models that can recapitulate the complex physiology of the cardiac tissue, there is a desire to create novel therapies and treatments. However, due to a lack of fundamental understanding of the heart's inflammatory response to myocardial infarction, the development of new therapies is both time consuming and costly. In this work, a novel approach to fabricating a dynamic hydrogel cardiac platform is reported. This platform better mimics the dynamic changes occurring in the native cardiac tissue microenvironment during cardiac …

Effect Of Current Density Ramping On The Anodic Reaction And Morphology Of Aerospace Aluminum Alloys, Peter Totaro Jr.

Dissertations

Aluminum anodizing has been experimented with and studied over the last century because of its ability to form uniform, well ordered cellular coatings on aluminum alloys. Anodizing aerospace alloys has been problematic, due to the alloying elements used to add strength and resistance to stress cracking corrosion. These intermetallic compounds, i.e., copper and zinc, promote oxygen evolution and stress as they accumulate in and on the surface of the forming aluminum oxide. These inclusions lead to increased electrical resistance that forms porous and flawed coating, which can lead to industrial and field failures. The amount of voltage placed on the …

Effect Of Process Control Agents Used In Mechanochemical Synthesis On Properties Of The Prepared Composite Reactive Materials, Mehnaz Mursalat

Dissertations

The study explores synthesis and reactivity of new reactive materials prepared by ball milling. High-energy ball milling became a ubiquitous mechano-chemical tool to manufacture diverse powders, from pharmaceuticals or foods to alloys to new solid rocket propellants. It enabled a dramatic expansion of the range of chemical compositions obtainable; however, it did not so far, allowed one to fine-tune morphology or interfaces in the generated powders. It is shown in this work how different process control agents (PCAs) can serve to tune the powder morphology and reactivity. Commonly used as lubricants and cooling agents during milling, liquid PCAs can be …

Understanding The Interfacial Processes Of Reactive Nanobubbles Toward Agricultural Applications, Xiaonan Shi

Dissertations

There is a growing interest in nanobubble (NB) technology because of its diverse applications (e.g., detergent-free cleaning, water aeration, ultra-sound imaging and intracellular drug delivery, and mineral processing). NBs have a higher efficiency of mass transfer compared to bulk scale bubbles due to the high specific surface areas. The high specific surface also facilitates physical adsorption and chemical reactions in the gas liquid interface. Furthermore, the collapse of NBs creates shock waves and the formation of hydroxyl radicals (OH).

However, it remains elusive why or how NBs are stabilized in water and particularly, the states of internal pressures of NBs …

Atmospheric Mercury Chemistry: Detection, Kinetics, And Mechanism, Na Mao

Dissertations

The presence of mercury in the environment is of global concern due to its toxicity. The atmosphere is an important transient reservoir for mercury released by human activities and natural sources. The knowledge of atmospheric mercury chemistry is critical for understanding the global biogeochemical cycle. In the atmosphere, mercury primarily exists in three forms: gaseous elemental mercury (GEM), gaseous oxidized mercury (GOM), and particulate-bound mercury (PBM). Over the last decade, the existing knowledge of mercury cycle has dramatically changed: (1) There has been increasing evidence that current detection methods do not accurately quantify gaseous oxidized mercury and a technique which …

A Detailed Parameter Study Into The Dermal Absorption Of Chemical Warfare Agents And The Effects Of Pharmacokinetics, Koko Lear

Theses

Chemical warfare agents (CWAs) are substances of varying toxicity profiles. These chemicals exhibit complex dynamics and pose a serious health risk when released into the environment. A mathematical model based on Fick’s second law of diffusion was developed to comprehend how these compounds were absorbed into the skin. The analysis applied to both small and large doses and, successfully, predicted experimental results. This work also includes the effects of CWA physicochemical properties on evaporation and dermal absorption through the stratum corneum. A sensitivity analysis was conducted to assess the impacts of small variations in the initial dose, environmental conditions, and …

A Vacuum-Driven Distillation Technology Of Aqueous Solutions And Mixtures, Guo Guangyu

Dissertations

Distillation of aqueous solutions and aqueous mixtures has vast industrial applications, including desalination, wastewater treatment, and fruit juice concentration. Currently, two major distillation technologies are adopted in the industry, membrane separation and thermal distillation. However, both of them face certain inevitable drawbacks. Membrane separation has disadvantages as relying on high-grade energy, requiring membrane, fouling problem, narrow treatment range, limited scalability, and vibrating and noisy operating conditions. Traditional thermal distillation technologies can avoid above concerns but has other shortcomings, such as relatively low energy efficiency and yield rate, complicated and bulky system structure, and scaling problem.

This project proposes an innovative …

Hydrodynamic Characterization Of Laboratory And Production Equipment For Pharmaceutical Testing And Manufacturing Using Experimental And Computational Approaches, Chadakarn Sirasitthichoke

Dissertations

The hydrodynamics of process units used in pharmaceutical industry, i.e., the distribution of velocity profiles and shear stresses within the vessel, often controls the process performance, significantly affecting product quality. The hydrodynamics is strongly influenced by several factors such as the vessel shape, stirrer type, presence of internals and baffles, agitation intensity, and liquid properties. Most of these parameters can be varied by the process designers and the operators to achieve the desired process outcomes. The impact of the hydrodynamics on the process outcome can be profound in both large vessels (e.g., reactors) and smaller vessels (e.g., dissolution vessels), involving …

Electric-Field-Driven Processes In Multiphase Fluid Systems, Qian Lei

Dissertations

Advantages of using electric fields in miniaturized apparatuses for a wide range of applications are revealed by numerous experimental and theoretical studies over the last several decades as it offers a simple and efficient method for manipulation of multiphase fluid systems. This approach is considered to be especially beneficial for control of boiling processes and colloidal suspensions considered in the presented work.

Boiling. Today's trends for enhancing boiling heat transfer in terrestrial and space applications focus on removal of bubbles to prevent formation of a vapor layer over the surface at a high overheat. In contrast, this dissertation presents a …

Bodipy Based Photodynamic Therapy And Potassium Probes, Xiangshan Liu

Dissertations

Boron dipyrromethene (BODIPY) has become more and more popular in photophysical and biological applications. BODIPY based fluorescence compounds have numerous advantage properties including low toxicity, high absorption extinction coefficients, high fluorescence quantum yields, sharp fluorescence emissions, and resistance to photobleaching. All the good properties lead to the wide applications of BODIPY based compounds. In this research, two different kinds of BODIPY are synthesized. Firstly, BDBrC containing carbazole and BODIPY core is synthesized. Cellular uptake research shows BDBrC can target on lysosome and singlet oxygen generation research result indicates that BDBrC can be used in photodynamic therapy. BDBrC also shows pH-sensitive …

Flexible Microfluidic Device With Nonplanar Interdigitated Microelectrodes, Saud Alssaidy

Theses

The lab-on-a-chip concept has improved significantly in recent years to meet global demand for various applications with the advent of new technologies. Much progress has been achieved, but many microfluidic devices still suffer from design limitations in terms of sensitivity and selectivity because they use rigid, fragile substrate materials and conventional electrodes, which do not provide high sensitivity or selectivity and suffer from signal-to-noise ratio issues. This work proposes a novel device architecture that uses flexible, transparent top and bottom layers integrated with (nonplanar interdigitated microelectrodes) to create a sandwich-like flexible substrate base. The top and bottom layers consist of …

Itraconazole Nanocomposites Prepared Via Rotary Evaporator Drying Of Nanomilled Suspensions, Alexander Santos Coelho

Theses

The aim of this study is to explore the feasibility of rotary evaporation for drying wetmilled drug suspensions as a novel approach to produce drug nanocomposites that exhibit fast redispersion and immediate drug release. To this end, the physical stability of the nanomilled itraconazole (drug) suspensions, a.k.a., nanosuspensions, during the milling and storage; the drying of the itraconazole nanosuspensions via the rotary evaporator; and the type/loading of various polymers/surfactants (dispersants) on aqueous redispersion and drug release from the nanocomposites were examined. Our results suggest that smaller drug particle size, owing to nanomilling, and smaller nanocomposite particle size, owing to optimized …

Advances In Modeling Gas Adsorption In Porous Materials For The Characterization Applications, Max A. Maximov

Dissertations

The dissertation studies methods for mesoporous materials characterization using adsorption at various levels of scale and complexity. It starts with the topic introduction, necessary notations and definitions, recognized standards, and a literature review.

Synthesis of novel materials requires tailoring of the characterization methods and their thorough testing. The second chapter presents a nitrogen adsorption characterization study for silica colloidal crystals (synthetic opals). These materials have cage-like pores in the range of tens of nanometers. The adsorption model can be described within a macroscopic approach, based on the Derjaguin-Broekhoff-de Boer (DBdB) theory of capillary condensation. A kernel of theoretical isotherms is …

Shale Softening Based On Pore Network And Laboratory Investigations, Di Zhang

Dissertations

This dissertation consists of two major parts: Firstly, experimental investigation of four major shale softening mechanisms and quantifications of structural parameters. Secondly, numerical simulations of nano-scale flow behaviors using the previous experiments determined parameters based on modified pore network modeling.

Hydraulic fracturing is widely applied to economical gas production from shale reservoirs. Still, the gradual swelling of the clay micro/nano-pores due to retained fluid from hydraulic fracturing causes a gradual reduction of gas production. Four different gas-bearing shale samples are investigated to quantify the expected shale swelling due to hydraulic fracturing. These shale samples are subject to heated deionized (DI) …

Feedstock Powders For Reactive Structural Materials, Daniel Hastings

Dissertations

Metals as fuels have higher energy density per unit mass or volume compared to any hydrocarbon. At the same time, metals are common structural materials. Exploring metals as reactive structural materials may combine their high energy density with attractive mechanical properties. Preparing such materials, however, is challenging. Requirements that need to be met for applications include density, strength, and stability enabling the component to sustain the structure during its desired operation; added requirements are the amount and rate of the energy release upon impact or shock. Powder technology and additive manufacturing are approaches considered for design of reactive structural materials. …

Towards Quality By Design (Qbd) Of Pharmaceutical Oral Films Loaded With Poorly Watersoluble Drugs, Eylul Cetindag

Dissertations

Oral films are an emerging drug delivery dosage form with numerous advantages such as ease of handling, the possibility to circumvent the first-pass metabolism, better patient compliance, capability for continuous manufacturing, and as a platform for personalized medicine. As films are different from other final dosages by their dimensions and their matrix form, further research is required to better understand the impact of excipient and drug on product performance to assure a consistent and good quality product. Therefore, this dissertation aims to contribute towards the processability and manufacturability of films by examining the impact of the materials and processes. First, …

Exploring Fused Deposition Modeling (Fdm) Three-Dimensional Printing Tablet Design Options For Pharmaceutical Dosage Forms, Guluzar Gorkem Buyukgoz

Dissertations

This dissertation examines the use of Fused Deposition Modeling (FDM) based three-dimensional (3D) printing approach for developing patient-specific dosage forms and addressing related technical challenges in such drug delivery systems. The first main objective is to explore pharmaceutical tablet design options using novel FDM 3D printing technology as the drug delivery platform such that drug form and tablet properties are tailored by considering patient age-specific formulations and dissolution control. Of the five different design options, two proposed options meet the main objective of providing similar drug release, whereas the popular option of fixed drug concentration but differing tablet size could …

Fluorine-Based Inorganic Oxidizers For Use In Metal-Based Reactive Materials, Siva Kumar Valluri

Dissertations

This work explores inorganic fluorides as oxidizers for fuel-rich reactive materials. A preliminary assessment of metal fluorides accounting for their enthalpy of formation points to bismuth (III) fluoride, BiF3 and cobalt (II) fluoride, CoF2 as oxidizers of interest. Initially, composite powders of aluminum with chosen fluorides at 50-50 wt. % are prepared by arrested reactive milling. Despite an increase in reactivity and lowtemperature ignition, the prepared composite powders are insensitive to initiation by electro-static discharge (ESD), making them attractive alternative to analogous thermites having very high ESD sensitivity. In air, the composite powder particles burn faster than reference aluminum particles …

Development Of Novel Inks And Approaches For Printing Tissues And Organs, Shen Ji

Dissertations

Tissue engineering is a multidisciplinary field that investigates and develops new methods to repair, regenerate and replace damaged tissues and organs, or to develop biomaterial platforms as in vitro models. Tissue engineering approaches require the fabrication of scaffolds using biomaterials or fabrication of living tissues using cells. As the demands of customized, implantable tissue/organs are increasing and becoming more urgent, conventional scaffold fabrication approaches are difficult to meet the requirements, especially for complex large-scale tissue fabrication. In this regard, three-dimensional (3D) printing attracted more interest over the past decades due to its unrivaled ability to fabricate highly customized tissues or …

The Aging And Impacts Of Atmospheric Soot: Closing The Gap Between Experiments And Models, Ogochukwu Yvonne Enekwizu

Dissertations

The main goal of this dissertation is to generate data and parameterizations to accurately represent soot aerosols in atmospheric models. Soot from incomplete combustion of fossil fuels and biomass burning is a major air pollutant and a significant contributor to climate warming. The environmental impacts of soot are strongly dependent on the particle morphology and mixing state, which evolve continuously during atmospheric transport via a process known as aging. To make predictions of soot impacts on the environment, most atmospheric models adopt simplifications of particle structure and mixing state, which lead to substantial uncertainties. Using an experimentally constrained modeling approach, …

Modeling Mass Transfer And Chemical Reaction In Industrial Nitrocellulose Manufacturing Processes, Francis Patrick Sullivan

Dissertations

A series of models are proposed to describe the production of military grade nitrocellulose from dense cellulose materials in mixtures of nitric acid, sulfuric acid, and water. This effort is conducted to provide a predictive capability for analyzing the rate and extent of reaction achieved under a range of reaction conditions used in the industrial nitrocellulose manufacturing process for sheeted cellulose materials. Because this capability does not presently exist, nitrocellulose producers have historically relied on a very narrow range of cellulose raw materials and resorted to trial and error methods to develop processing conditions for new materials. This tool enables …

Development Of Novel Membranes For Nanocarbon Enhanced Separation With Application In Biofuels And Solvent Recover, Oindrila Gupta

Dissertations

Pharmaceutical industries historically have had one of the highest amounts of solvent waste generated per unit of drug manufactured. Energy requirements and carbon footprint of current solvent recycling processes tend to be quite high, and the incineration of the solvents for waste disposal produces toxic air emissions. Also, rapidly increasing demand for energy and strict regulation on engine pollutant emissions have necessitated the use of alcohol as carbon-neutral fuels. Thermal distillation is one of the most common methods for the separation of alcohol-water mixtures. However, its application is limited due to energy requirements and high operating costs, and heating to …

Predicting Bulk-Scale Properties Of Pharmaceutical Powders From Their Particle-Scale Dimensionless Measures, Kuriakose T. Kunnath

Dissertations

Loose powder packing and flowability are both important bulk properties to consider in relation to pharmaceutical tablet and capsule manufacturing. These properties as well as cohesive powder agglomeration tendency impact the efficiency of various processes such as feeding, blending, conveying, and compaction, and could have an adverse effect on final drug product. Pharmaceutical powders are often milled to fine sizes (<100 gm) for dissolution improvements via increased available surface area. However, such particle size reductions lead to inadequate bulk powder properties due to high cohesion among the individual particles. Recent work has demonstrated the ability of nano-silica dry coating techniques to significantly decrease interparticle forces without changes in particle size. In this work, the ability to predict properties such as powder bed porosity, flowability, and particle agglomeration both before and after nano-silica dry coating is examined, along with assessment of the extent of property enhancements after dry coating. Previous studies have utilized empirical approaches to build property prediction models. However, such approaches lack physical fundamentals which dictate bulk powder behavior and would be unable to account for the effects of dry powder coating. Incorporation of physics can be done via computation of the granular Bond number, as is done in this study for a large dataset of commonly used pharmaceutical powders, with wide variations in particle size, shape, density, and surface roughness. Predictive capability of current Bond number models is investigated, reasons for outliers are elucidated, and amendments to improve prediction is attempted. Overall, the aim of this work is to expand generalizability of Bond number models to a wider variety of particles, and extend its use from single powders to multi-component mixtures. The major outcome of this work is the development of a predictive framework that is expected to simplify pharmaceutical dry powder formulation development, reduce required experimental testing, and provide quantifiable estimates to aid processing route decision making.

Preparation And Characterization Of Reactive Composites Combining Boron With Mixed Oxides, Purvam Mehulkumar Gandhi

Theses

Thirteen liquids have been explored as Process Control Agents (PCAs) for high-energy mechanical milling of two metal oxide powders, CuO and Bi₂O₃, with the practical purpose to reduce the sizes of powder particles and refine their crystal structure. Multiple liquid properties have been considered to analyze their effect on evolution of both particle and crystallite sizes during milling for each oxide. Experimental data were analyzed using the δ-AICc (Akaike Information criterion) correlation function applied to linear relations between liquid properties and powder characteristics. Multiple linear correlation models were ranked based on the highest log-likelihood and the …

Stress-State And Injection-Rate Dependent Damage Processes During The Hydraulic Fracturing Of Granite, Gayani Sasendrika Gunarathna

Dissertations

Hydraulic fracturing is a well-stimulation technique that is employed in field applications, such as enhanced geothermal systems (EGS) and shale oil/gas extraction. This research experimentally investigates the effect of the state of stress and injection rate on the hydraulic fracturing processes. In addition, a displacement discontinuity method (DDM) code, FROCK, is used to model the crack initiation and propagation in a granite specimen under hydraulic fracturing conditions. In order to conduct the experimental work, a test setup capable of applying a triaxial state of stress and water pressure inside pre-fabricated flaws cut in prismatic granite specimens is developed. Additionally, the …

Calculating Elastic Properties Of Confined Simple Fluids, Christopher D. Dobrzanski

Dissertations

Confinement in nanoporous materials is known to affect many properties of the fluids confined within their pores. The elastic properties are no exception. This dissertation begins with an overview of the relevant literature on ways of obtaining elastic properties of confined fluids. It outlines some fundamental gaps in our understanding. The chapters following address some of these gaps in understanding elastic properties of the confined fluid, in particular, how the shape of the confining pore matters, how supercriticality effects the properties, how an equation of state designed for confined fluids can be used to calculate elastic properties, and if an …

Che 472-Hm2: Process And Plant Design Honors, Nellone Reid

Chemical and Materials Engineering Syllabi

No abstract provided.

Customized Boron And Magnesium-Based Reactive Materials Prepared By High Energy Mechanical Milling, Xinhang Liu

Dissertations

New reactive materials need to be developed having biocidal combustion products. When ignited, such material can add chemical biocidal effects to the common effects of high temperature and pressure. Biocidal combustion products are capable of deactivating harmful spores or bacteria, which can be released by targets containing biological weapons of mass destruction. Research showed that halogens, especially iodine, are effective as biocidal components of reactive material formulations. Recently, magnesium combustion product MgO is also found to have a biocidal effect. Thus, advanced formulations containing both magnesium and iodine are of interest; such formulations are prepared and investigated here.

Reactive materials …