Chemical Engineering Commons^™

Effects Of Molecular Characteristics Of Polymers On Drag Reduction, Gin‐Chain ‐C Liaw, Jacques L. Zakin, Gary Kent Patterson

Chemical and Biochemical Engineering Faculty Research & Creative Works

Turbulent measurements in capillary tubes and in pipes were made on nonpolar solutions of seven polymer species, three at more than one molecular weight, over wide concentration ranges. A critical concentration, Cc, was taken as the minimum concentration for disappearance of the turbulence transition region. Above this concentration, friction factor‐generalized Reynolds number data show only a gradual deviation from extension of the laminar line. Cc increases with tube diameter and decreases with molecular weight. The critical dimensionless volume friction Cc [η] is less dependent on molecular weight. The levels of Cc [η] for different polymer species in a given tube …

Organic Desorption From Carbon-I. A Critical Look At Desorption Of Unknown Organic Materials From Carbon, S. C. Allen, R. H. Pahl, Kenneth G. Mayhan

Chemical and Biochemical Engineering Faculty Research & Creative Works

No abstract provided.

A Measurement Of Complex Viscosity With Large Amplitudes, Kuo-Shein Shen

Doctoral Dissertations

"In order to study the viscoelastic properties of polymer solutions and greases, a dynamic apparatus was built for making measurements of complex viscosity. Characteristic impedance was measured by a force transducer, an accelerometer and a phase meter. Large amplitudes to 0.5 inch can be obtained with this apparatus. The largest amplitude used was 1.27 x10⁻¹ cm. The frequency range was 30 Hz - 1500Hz. The lowest dynamic viscosity to be measured was 0.5 poise. In order to determine the capabilities of the instrument, complex viscosities of polymer solutions and greases were measured. The polymer solutions studied were polyisobutylene (PIB) L-80, …

The Effect Of A Knurled Heat Transfer Surface Upon Pool Nucleate Boiling Of Normal Pentane, Jerry James Carr

Doctoral Dissertations

"The effect of knurling a nucleate boiling heat transfer surface was studied. The knurling utilized produced regular, four-sided, adjacent pyramids with an apex angle of 90 degrees. Four knurling densities were used ranging from 416 to 2591 pyramids per square inch. The transfer surface was gold-plated copper and the heaters used were electrically heated, ten-inch long, horizontal cylinders of one-inch diameter. The liquid boiled was normal pentane at its saturation temperature and a pressure of 760 millimeters mercury.

For some of the knurled surfaces the temperature difference required to produce a given heat flux was found to be less than …

On-Line Economic Optimization Of A Chemical Reactor, Jesse Daniel Bennett

Doctoral Dissertations

"An economic optimizing control system for a continuous flow stirred tank chemical reactor is designed, simulated, and installed on a pilot scale reactor. The control scheme utilizes a reaction and reactor model to predict on-line the economic optimum of a reactant concentration. In this manner the control system manipulates the reactant flow rate to maintain the optimum concentration during changes in reaction-reactor parameters with time. Typical parameter changes include the decay of reaction catalyst activity. The optimizing controller will function in conjunction with various operating policies including control to maintain a specified production rate"--Abstract, page ii.

An Empirical Method Of Correlating Compressibility Factors Of Nitrogen - Helium - Hydrocarbon Systems, Terry Wayne Buck

Masters Theses

"Compressibility factors have been taken from previous works by Davis and Taneja for twelve different common oil-field hydrocarbon mixtures which contain at least 2 mole % nitrogen. An effort has been made to show that by using the Benedict-Webb-Rubin Equation of State it is possible to predict compressibility factors using a correlation of error in predicted compressibility factor versus reduced pressure, at different mole % of nitrogen with constant reduced temperatures, if the critical points of the mixtures are known or can be calculated. In the mixtures which contain helium, the only effect of helium seems to be the raising …

Binary Molecular Diffusivities In Liquids: Prediction And Comparison With Experimental Data, Ronald Dean Mitchell

Doctoral Dissertations

"The Eyring rate theory equation has been modified successfully to enable predictions of binary molecular diffusivities for a wide variety of liquid-liquid systems. The activation free energy for binary diffusion has been evaluated in terms of the activation free energies for self diffusion of the solvent and solute. This was accomplished through the use of regular solution theory by relating the bond breaking energy of the jump step to the bond breaking energy in evaporation. Diffusivities estimated by this equation and the equations developed by Olander, by Gainer and Metzner, and by Wilke and Chang were compared with experimental data. …

An Sem Surface Study Of Nucleate Pool Boiling Heat Transfer To Saturated Liquid Nitrogen Reduced Pressures From 0.1 To 0.9, David Virgil Porchey

Doctoral Dissertations

"This study constituted an examination of both nucleate boiling and maximum heat flux characteristics of liquid nitrogen boiling from characterized surfaces. Several textures of gold plated copper surfaces were studied in addition to silver and silver oxide surfaces. Data were taken over a wide range of reduced pressures. All surfaces were examined using a Scanning Electron Microscope (SEM). Data and micrograph comparison revealed that both surface chemistry and surface roughness affect the nucleate boiling characteristics of liquid nitrogen. These effects are separated from each other showing that nucleate boiling is a function of both surface chemistry and topography. Surface roughness …

A Three-Dimensional Mathematical Simulator Of Multiphase Systems In A Petroleum Reservoir, Leonard Koederitz

Doctoral Dissertations

"A generalized digital analysis for calculating three phase, three dimensional flow in reservoirs is developed. The computerized mathematical model is applicable to depletion drive, gas injection, water injection, and/or aquifer drive systems with modifications specific to the simulation criterion of that type of drive and includes fluid compressibility effects, gravity drainage and capillary pressure. The simulation allows arbitrary consideration of reservoir heterogeneity, geometry, well locations and rates of production. An innovation to the alternating direction technique for linear differential equations discussed by Brian is developed and employed in order to render the method of solution applicable to non-linear differential equations. …

Anodic Dissolution Of Zinc In Potassium Iodide-Potassium Iodate Solutions, Chi-Chiu Yao

Doctoral Dissertations

"The anodic dissolution of Zn was studied in KI-KIO₃ solutions at 25ºC. In I⁻ solutions, it was found that the apparent valence of Zn ions going into solution is approximately two. Smaller values are obtained in IO₃⁻ solutions, with the most pronounced changes occurring in the higher concentrations. An empirical equation is derived relating the apparent valence (or anode efficiency) to the current density and concentrations of IO₃⁻ and I⁻. An anodic dissolution mechanism is proposed"--Abstract, page 1.

Investigation Of Liquid Carryover In The Girdler-Sulfide Process For Production Of Heavy Water At The Aec Savannah River Plant, Samuel Clark Allen

Doctoral Dissertations

"An investigation of the causes of liquid carryover in the Girdler-Sulfide process for the production of heavy water was carried out using 12 samples of carbon collected over a one-year time period. Organic impurities from the feedwater were concentrated by adsorption on carbon. Studies of methods for the drying of carbon showed that freeze drying resulted in the minimum reproducible moisture retention without gross loss of the adsorbed organic materials. Rotary vacuum evaporation and air drying of beds of carbon were proven to be less efficient. A study was made of the variables which affect extraction efficiency by the Soxhlet …

The Cathodic Reduction Of Maleic Acid, Show Yih Hsieh

Doctoral Dissertations

"The electrochemical reduction of maleic acid (0.0003 to 0.3 M) was studied on Hg, 0.5% Bi(Hg) amalgam, 5.0% Bi(Hg) amalgam, and Bi cathodes in 1 n H₂SO₄-K₂SO₄-KOH electrolytes (pH 0.3 to 4.0) at 60°C. The maleic acid was converted to succinic acid with high efficiencies (86 to 100%) on all cathodes. Polarization curves with linear Tafel sections were found. All the cathodes had similar kinetic parameters...A reaction mechanism consistent with the experimental observations is proposed..."--Abstract, pages ii-iii.

Effect Of Axial Dispersion On Interphase Mass Transfer In Packed Absorption Columns, Virendra Kumar Mathur

Doctoral Dissertations

"A steady state approach was followed in this investigation to determine the effects of liquid and gas flow rates, packing size and packing height on the interphase mass transfer coefficient and gas phase axial mixing Peclet numbers. Experiments were performed on the absorption of carbon dioxide from a mixture of carbon dioxide and nitrogen in a packed column. Absorption was performed using 1/4, 3/8 and l/2 inch Raschig rings, with a packing height of 3 feet and also using 3/8 inch Raschig rings with a packing height of 5 feet. The liquid and gas flow ranges used were 2865 to …

The Anodic Dissolution Of Tungsten, Ching-Lun Wu

Masters Theses

"The anodic dissolution of tungsten was studied in H₂SO₄-K₂SO₄ solutions (pH= -2 to 2.5) andK₂SO₄-K₂CO₃-KOH solutions (pH = 11.5 to 14.5) at 25ºC. Faradaic efficiency studies in basic solutions showed that the metal was oxidized to the +6 state. In acid solutions, a thick protective film of yellow WO₃ was formed. Polarization measurements showed linear Tafel behavior (slope ~ 2.3RT/F) in the potential region slightly more positive than the rest potentials. An anodic dissolution mechanism is proposed which involves a surface film of W₂O₅ that is further oxidized to WO₃ and dissolves by hydrolyzation"--Abstract, page 1.

A Comparative Study Of Experimental And Computed Compressibility Factors Of Ethane-Carbon Dioxide-Nitrogen System, Brij Raj Misra

Masters Theses

"The purpose of this study was to provide compressibility factor data on the ethane - carbon dioxide - nitrogen system. Compressibility factors were experimentally determined for 5 mixtures at room temperature, 100ºF, 125ºF , 150ºF and pressures ranging between 1000 psig to 4000 psig. An attempt was also made to compare the experimental data with the compressibility factors obtained by the additive volume method. The deviation of the computed compressibility factor from the experimental data was found to be in accordance with the general view of previous workers. However, the deviation was found to be a maximum in the pressure …

Shear Degradation Of Polystyrene In Toluene, Ali Asghar Sarmasti

Masters Theses

"The purpose of this study was to investigate the extent of flow degradation of narrow molecular weight distribution polystyrene samples under the conditions of laminar flow in capillary tubes. In all cases the solvent was toluene at 25ºC, the polymer concentration was 0.1 weight percentage, and the calculated shear rate at the wall was in the range of 10⁵ - 10⁶ sec⁻¹. The extent of degradation was obtained by measuring the intrinsic viscosity [eta] of the polystyrene samples before and after flow through capillary tubes having a wide range of length/diameter (L/D) ratios. The polystyrene samples here had molecular weight …

Effect Of Third Components On Drag Reduction In Aluminum Soap-Hydrocarbon Systems, Kun-Chieh Lee

Masters Theses

"The effect of additives, aging, shear and peptizing agents on the drag reducing abilities of aluminum disoaptoluene solutions prepared at room temperature were studied. Viscosity measurements were used as a primary test to select effective additives. Medium strong organic bases were found to be useful as they speed up the dissolution of slow dissolving aluminum dioctoate soap and form large micelle structures. These peptizers are not effective with aluminum distearate which is very hard to dissolve in toluene at room temperature. Turbulent flow pressure drop measurements at various aging times were made for solutions of 0.1 per cent aluminum dioleate …

Chromatographic Determination Of Hydrocarbons Based On Retention Time Data For Squalene And Tetracyanoethylated Pentaerythritol Columns, Mehdi Honarpour

Masters Theses

"The purpose of this thesis is to investigate the theory that when several members of a homologous series are injected into a gas chromatograph, at a given flow rate and column temperature, the lograrithm of their retention time as a function of some increasing property of the homologous series may be presented as a straight line and to develop their equations. Experimental procedure was accomplished for the normal paraffin series with 7 1/2% squalene and 10% Tetracyanoethylated Pentaerythritol (T.C.E.pageE.) columns and the relation between retention time and carbon number was determined. The same type of development was employed for aromatic …

A Permeability Scaling Technique In The Numerical Simulation Of Water Coning, Virendra Kumar Dutta

Masters Theses

"A two-dimensional, two-phase, radial, horizontally layered water coning simulator was programmed for large memory digital computers. A permeability sealing technique is developed which allows the use of large size blocks as production blocks. As a result of this technique large time steps have been used without causing saturation instabilities around the well bore and the permeability scaling technique allows a more realistic simulation of a water cone. The IMPES method is used to calculate pressure and saturation in the system for each finite time step. The behaviour of the simulator is studied for various factors affecting the advance of a …

Simulation Of A Gas Storage Reservoir With Leakage By A Two-Dimensional Layered Mathematical Model, Steven William Ohnimus

Doctoral Dissertations

"A generalized mathematical model was developed for two-dimensional compressible fluid flow accounting for the effects of relative permeability capillary pressure, and gravity drainage in addition to the reservoir properties of rock heterogenity and reservoir geometry. The generalized model developed was applied to an aquifer gas storage reservoir in which vertical leakage occurred from the main reservoir to two adjacent overlaying zones. The experimental results of Thomas, et al. were utilized in applying the model to gas storage injection/withdrawal periods yielding reasonable results for the three layers"--Abstract, page ii.

Drag Reduction Correlations, Gary Kent Patterson, J. L. Zakin, J. M. Rodriguez

Chemical and Biochemical Engineering Faculty Research & Creative Works

No abstract provided.

A Case For University Credits For Industry's In-House Continuing Education Programs, Robert E. Carlile

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

The minerals industries have long recognized the tangible and intangible returns from continuing education programs for their technical scientific and administrative personnel. These programs originate from the mutual desires of the employer to upgrade the professional competence of the employee and the employee's concurrent desires to keep abreast of new developments to review the state of the art of specialized subjects and to better qualify himself to compete in an every changing technology. In-house training and continuing education programs to provide such review and education for the employee are becoming a recognized function of companies comprising this industry. These company-sponsored …

Determination Of Reservoir Characteristics From Capillary Pressure Curves And Electrical Properties Of Rocks, Prasanta Kumar Guharoy

Masters Theses

"Based upon the assumptions that a porous medium is analogous to a bundle of capillary tubes and that there is equivalence of electrical and hydraulic tortuosity in a porous medium, empirical expressions are presented which relate capillary pressure data and electrical properties of the rock to the porosity, permeability and relative-water permeability, respectively, of completely water-wet rocks. Experimental data are presented for comparison in order to verify their validity. Three principal models are presented, each of which is characterized by a particular expression for estimating tortuosity. The method of determining this parameter was varied in order to find the form …

The Anodic Dissolution Of Zinc In Potassium Chloride-Potassium Chlorate Solutions, Kuei Chun Chen

Masters Theses

"The anodic dissolution of Zn was studied in Cl⁻-Clo⁻₃; solutions at a temperature of 25ºC. It was found that the apparent valence of Zn ions going into solution was approximately the normal value of two at low current densities. An empirical equation was derived relating the apparent valence to the current density and both concentrations of Cl⁻ and Clo⁻₃. An anodic dissolution mechanism was proposed"--Abstract, page 1.

Degradation Of Polystyrene Solutions By Capillary Shear, Tyan-Faung Niu

Masters Theses

"An apparatus has been constructed to investigate the capillary shear degradation of polymer solutions. Maximum shear rates obtainable under flow conditions which could be characterized as nonturbulent were on the order of 10₅ sec⁻¹. The effect of calculated shear rate, initial molecular weight, and number of passes through the capillary tube on the degradation of polystyrene (with M̄_v from 22,000 to 1,770,000) solutions in toluene (0.1 wt.%) were studied. The tests in the 0.0105 in. ID stainless steel tube at a calculated shear rate of 1.36 x 10₅ sec⁻¹ show that, for equal number of passes, the lower the …

The Electrochemical Behavior Of Molybdenum In Acidic Chloride Solutions, Mun-Shan Lee

Masters Theses

"The anodic dissolution of Mo was studied in HC1-KC1 solutions at 25ºC. The apparent valences of Mo ions going into solution were approximately six. Lower values were obtained in HC1 solutions, with the most pronounced changes occurring with the higher concentrations. The resultant ions in solution were Mo-VI. The Mo surface in aqueous solutions appears to be covered with an oxide whose approximate composition is Mo₂O₅. The anodic dissolution is controlled by the oxidation of the surface oxide (Mo₂O₅) to MoO₃"--Abstract, page 1.

Comparison Of The Buckley-Leverett Technique With A Numerical Simulation Model Containing Heterogeneity And Capillary Pressure, Krishna Kumar Singh

Masters Theses

"A numerical model for a linear, two-phase fluid flow system has been developed with the capabilities of accounting for heterogeneity and capillarity. The model developed is general enough to analyze either water-oil or gas-oil systems. A hypothetical petroleum reservoir (containing only water and oil) under water flood was studied. The results for the homogeneous, no capillary pressure case were found to be similar to those obtained by the Buckley-Leverett technique. The study shows that the Buckley-Leverett is accurate even for a certain degree of heterogeneity. Also, capillarity does not substantially alter the results for the system studied. The results obtained …

A Comparative Study Of Experimental And Computed Compressibility Factors Of Methane-Nitrogen-Carbon Dioxide System, Piloo Eruchshaw Ilavia

Masters Theses

"Experimentally determined compressibility factors of a natural gas with impurities like carbon dioxide and nitrogen are found to differ with the values computed by various methods making use of compositional breakup of the gas. Compressibility factors for five mixtures of known composition were experimentally determined at room temperature, 100ºF, 125ºF, and 150ºF, and at pressure ranging between 1000 psi to 4000 psi. Using the known composition of the mixtures, compressibility factors were calculated by additive volume method and by Eilerts method. The deviation between computed and experimentally determined compressibility factors are at a maximum in the lower and higher pressure …

The Anodic Dissolution Of Tin In Acidic Chloride Solutions, Edward Chung-Hong Liu

Masters Theses

"The anodic dissolution of Sn in acidic chloride solutions (pH = -2.0 to 2.9) was studied at 25ºC. The apparent valence of the dissolving ions varied from about 0.4 to 2.4, a function of both electrolyte and c.d. The complexing of Sn⁺² by Cl⁻ had an important influence with SnCl₃⁻ apparently being the dominant products. A reaction sequence is proposed involving the step-wide oxidation of Sn accompanied by reaction with Cl⁻"--Abstract, page 1.

The Cathodic Reduction Of Bromate Ions On Mercury In Neutral And Basic Solutions, Jaw-Shin Chang

Masters Theses

"The reduction of BrO⁻₃ was studied in neutral and basic solutions on a stationary Hg surface under activation controlled conditions. Coulombic efficiency studies showed that BrO⁻₃; was reduced to Br⁻ with high efficiencies. The polarization measurements lead to a proposed reaction scheme which is consistent with the experimental observations"--Abstract, page 1.