Chemical Engineering Commons^™

Elucidating The Properties And Mechanism For Cellulose Dissolution In Tetrabutylphosphonium-Based Ionic Liquids Using High Concentrations Of Water, Brad Crawford

Graduate Theses, Dissertations, and Problem Reports (ETD)

The structural, transport, and thermodynamic properties related to cellulose dissolution by tetrabutylphosphonium chloride (TBPCl) and tetrabutylphosphonium hydroxide (TBPH)-water mixtures have been calculated via molecular dynamics simulations. For both ionic liquid (IL)-water solutions, water veins begin to form between the TBPs interlocking arms at 80 mol % water, opening a pathway for the diffusion of the anions, cations, and water. The water veins allow for a diffusion regime shift in the concentration region from 80 to 92.5 mol % water, providing a higher probability of solvent interaction with the dissolving cellulose strand. The hydrogen bonding was compared between small and large …

A Comparison Of Fiber Mat Thickness Measurement Techniques Using Laser Interferometry And Water Displacement, Ryan Seabeck

Williams Honors College, Honors Research Projects

Polymer fiber mats may often be very thin which leads to complications in measuring thickness. The thickness of fiber mats, however, is crucial in understanding their behavior. Thickness affects how well the mat works as a filter as well as the pressure drop across the mat, and herein lies the need for accurate measurement techniques. Currently two of the available techniques for measuring mat thickness are by laser interferometry[1] and by buoyancy force when submerged in water[2]. Instead of measuring the buoyancy force in this experiment, an enclosure intended to measure the thickness via water displacement was …

Design Of Pigments For Use In “Cool” Coatings, Tyler Laughorn

Williams Honors College, Honors Research Projects

This project was focused on the development and testing of several novel pigments that exhibit high NIR-reflectance and therefore show potential for use in “cool” coatings. A “cool” coating will reflect more solar radiation than other standard coatings, and so a coated structure would require less energy to keep cool. Four sets of pigments were synthesized: Co_1-xMg_xCr₂O₄ (teal), Co_0.25Mg_0.75Cr_2-yAl_yO₄ (blue), Ti_1-x-yNi_xSb_yO₂ (yellow), and Cr_2-xFe_xO₃ (black). NIR and TSR values were then measured …

Filtration Apparatus Design For Oil-Water Separation Using Membranes And Sponges, Alec Jerger

Williams Honors College, Honors Research Projects

It can be difficult to separate water and oil emulsions through traditional filtration. Therefore, investigations of filtering using thermo-responsive (TR) polymers, in this case poly(vinyl methyl ether) (PVME), was conducted. It’s hypothesized that below its lower critical solution temperature (LCST), PVME has an affinity for water while oil substances do not. Above the LCST the opposite will be true. To verify this hypothesis, iterations of filtration designs were created to provide optimum control over the parameters to measure flow. The final optimized experimental apparatus was a Chromaflex glass column which was air tight and controlled all parameters besides fluid flow. …

Zips Precious Plastics: Plastic Extruder, Patrick Cole

Williams Honors College, Honors Research Projects

This project's goal was to design and build an affordable desktop filament extruder that can precisely and consistently extrude filament to a certain tolerance acceptable for 3D printers using wasted printing material. The group is partnering with an on campus organization focusing on engineering applications for sustainable futures. Zips Precious Plastics is a student run design group that intends to bring an innovation space on campus to help educate students about the importance of a closed looped system within plastic manufacturing.

Controlled Crystallization Of Pet Filaments In Additive Manufacturing, Ryan Kordahi

Williams Honors College, Honors Research Projects

Polyethylene terephthalate (PET) appears in daily life in many forms, the most common being disposable soft drink bottling. To deal with the ever-growing quantitity of disposed PET (both in landfills and environment), a waste plan revolving around depolymerization should be implemented. Specifically, the potential of PET depolymerization through aminolysis into useful, low molecular weight monomers will be explored with the end goal of producing a 3D printing filament and analyzing economic feasibility.

Evaluating Rubber Aging On Tire Durability: Quantitative Evaluation Of Rubber Aging, Brian Auffenberg

Williams Honors College, Honors Research Projects

Rubber is considered one of the most important polymers in the world due to its variety of uses. There are many different conditions that can affect the useful life of rubber. The purpose of this research was to determine how the mechanical loading on the rubber may affect the aging of the rubber. The scope of the project was to focus on the rubber used for tire production. The research was limited to focusing only on rubber supplied by industry mentors which was styrene-butadiene rubber. By varying the length of time for testing as well as the temperature of the …

A Foundational Approach To Extrusion And Compounding, David Frankart

Williams Honors College, Honors Research Projects

With a history of nearly 200 years, polymer processing and compounding is constantly changing to fit the material science needs of the era. Exposure of undergraduate students to the technology and practices used in industry today in a lab setting would create new opportunities for experiential learning and growth. The objective was to set up a 0.75”, 25 L/D Thermo Haake single screw extruder for lab use and run trials of material in a single screw extruder to set up a basis for experiments. Trials were run of co-polyester resin through a single screw extruder with carbon fiber additives varying …

Effects Of Crosslinking Conditions On Biofouling Of Polymer Substrates With A Hydrogel Layer, Laura Davila

Williams Honors College, Honors Research Projects

The introduction of a hydrogel coating to a surface has been looked at for different benefits. Certain hydrogels offer antifouling properties that are beneficial to different applications like medical components. Previous attempts (2) (3)have been done to introduce a hydrogel surface to plastic substrates. One of them is to use grafting brushes which works properly but it is not sufficient since the layer is too thin and therefore can be damaged. The second method have a bulkier coating without crosslinking. Opposite to grafting brushes this method has too thick of a layer. Additionally, there is no crosslink therefore the coating …

Formulation And Validation Of Nanoparticle Controlled Delivery For Chemotherapeutic Drug Products, Shani L. Levit

Theses and Dissertations

Taxol, a formulation of paclitaxel (PTX), is one of the most widely used anticancer drugs, particularly for treating recurring ovarian carcinomas following surgery. Clinically, PTX is used in combination with other drugs such as lapatinib (LAP) to increase treatment efficacy. Delivering drug combinations with nanoparticles has the potential to improve chemotherapy outcomes. In this study, we use Flash NanoPrecipitation, a rapid, scalable process to encapsulate weakly hydrophobic drugs (logP in vitro. Encapsulating either PTX or LAP into nanoparticles increases drug potency. When PTX and LAP are co-loaded in the same nanoparticle, they have a synergistic effect that is greater than …

Dendrimer-Based Therapeutic Delivery Vehicle For The Treatment Of Ocular Diseases, Remy C. Cooper

Theses and Dissertations

The treatment of ocular diseases poses a significant challenge to drug delivery design, due to the eye’s complex anatomy, with a semi-permeable blood-ocular barrier and associated immune privilege. To address some of the delivery challenges, polycationic dendrimers are explored as vehicle for the treatment of posterior chamber disease. Dendrimers are a class of polymeric nanoparticles that are highly branched, multivalent and monodisperse, whose three-dimensional globular architecture has given them the nickname of “synthetic proteins”. Dendrimers are synthesized by reacting monomers in a step-wise fashion to produce generationally and radially increasing structures, with core, interior and surface chains that are highly …

Enhanced Methane Hydrate Formation Using Promoters For Natural Gas Storage And Transportation Application, Katipot Inkong

Chulalongkorn University Theses and Dissertations (Chula ETD)

Solidified natural gas (SNG) is an alternative technology for natural gas storage and transportation in the clathrate hydrate formed. It has higher volumetric energy storage with the ease to handle not to mention its safety. Effects of different hydrate promoters, including methyl ester sulfonate (MES), tetrahydrofuran (THF), hollow silica (HS), and sodium dodecyl sulfate (SDS), on the methane hydrate formation was investigated. All experiments were performed in an unstirred tank reactor at desired experimental conditions. The results indicated that all promoters significant enhanced the hydrate formation both kinetics and methane uptake compared with pure water. The increase in the MES …

Bimetallic Nanoparticles Integrated Membranes For Groundwater Remediation: Synthesis, Characterization And Applications, Hongyi Wan

Theses and Dissertations--Chemical and Materials Engineering

The detoxification of chlorinated organics from groundwater, such as trichloroethylene (TCE), tetrachloroethylene (PCE), polychlorinated biphenyl (PCB) and carbon tetrachloride (CTC), is a challenging area. Reductive dechlorination has been investigated using iron and iron-based nanoparticles, such as bare Fe, sulfidized Fe (S-Fe) and palladized Fe (Pd-Fe). However, issues including particle agglomeration, difficulties in recycling and particle leaching have been reported to hinder the application and wide usage of these techniques. The integration of nanoparticles and membranes can address these issues because of the large surface area, stability, and the potential for versatile functionalities. In this study, commercial polyvinylidene difluoride (PVDF) microfiltration …

A Thermodynamic And Feasibility Study Of Green Solvents For The Fabrication Of Water Treatment Membranes, Xiaobo Dong

Theses and Dissertations--Chemical and Materials Engineering

Nonsolvent induced phase separation (NIPS) has been widely used to fabricate polymeric membranes. In NIPS, a polymer is dissolved in a solvent to form a dope solution, which is then cast on a substrate and immersed in a nonsolvent bath, where phase inversion occurs. Petroleum-derived organic solvents, such as N-Methyl-2-Pyrrolidone (NMP) and Dimethylacetamide (DMAc), have been traditionally used to fabricate polymeric membranes via NIPS. However, these solvents may have negative impacts on environmental and human health; therefore, using greener and less toxic solvents, preferably derived from biomass, is of great interest to make membrane fabrication sustainable. In this dissertation, two …

Polymeric Nanocomposite Membranes With Phosphorene Based Pore Fillers For Fouling Control, Joyner Eke

Theses and Dissertations--Chemical and Materials Engineering

Phosphorene is a two-dimensional material exfoliated from bulk phosphorus. Specifically, relevant to the field of membrane science, the band gap of phosphorene provides it with potential photocatalytic properties, which could be explored in making reactive membranes able to control the accumulation of compounds on the surface during filtration, or fouling. Another reason phosphorene is a promising candidate as a membrane material additive is due to its catalytic properties which can potentially destroy foulants on the membrane surface.

The first goal of this study was to develop an innovative and robust membrane able to control and reverse fouling with minimal changes …

Methods For Film Coating Electrospun Fibers, Kristopher Dejean

Williams Honors College, Honors Research Projects

Electrospinning uses high voltages to form polymer nanofiber membranes. These membranes have potential for use in filtration, tissue engineering, drug delivery, and catalysis. The nonwoven fiber mat is malleable but has a low tensile strength compared to a solid film of the same polymer. Joining the fibers with a thin film is desired to balance the strength and flexibility. Three methods of producing a film on fiber membrane were tested. The techniques are spraying then melting, spin coating, and dip coating. Electrospinning setup conditions, solvent ratios, damage to fibers, and spin coating speeds were determined. Research was abruptly stopped and …

Exploring Shape-Memory Polymers From Silicone I And 1,10-Decanediol Blends, Kristina Nguyen

Williams Honors College, Honors Research Projects

Shape-memory polymers (SMPs) are polymeric materials that have dual-shape capabilities. These materials can deform to a temporary shape and will recover to their permanent original shape when induced by an external stimulus such as heat. The purpose of this project was to investigate the thermo-mechanical properties and shape-memory behavior of various blends of Silicone I and 1,10-decanediol to determine if a unique blend of these components can be utilized to develop shape memory surface relief patterns.

Careful iterative experiments were used to develop a robust procedure for the fabrication of crosslinked sheets of blends of Silicone I and 1,10-decanediol over …

Effects Of Hofmeister Ions On Solubility And Swelling On Gelatin Hydrogels, Hannah Eldridge

Williams Honors College, Honors Research Projects

Hydrogels are known to be weak and brittle, due to the amounts of water that they hold. Gelatin-based hydrogels specifically are inexpensive and easily accessible, but often have poor physical properties. The goal of my project was to strengthen gelatin-based hydrogels and improve their mechanical properties by forming these hydrogels in different aqueous solutions containing kosmotropic Hofmeister's ions. Prior research has shown that these ions are able to take water away from gelatin-based gels, which forms a tougher hydrogel. The success of this project will be measured by studying the solubility and swelling effects that different Hofmeister ions have on …

Methods For Film Coating Electrospun Fibers, Kristopher Dejean

Williams Honors College, Honors Research Projects

Electrospinning uses high voltages to form polymer nanofiber membranes. These membranes have potential for use in filtration, tissue engineering, drug delivery, and catalysis. The nonwoven fiber mat is malleable but has a low tensile strength compared to a solid film of the same polymer. Joining the fibers with a thin film is desired to balance the strength and flexibility. Three methods of producing a film on fiber membrane were tested. The techniques are spraying then melting, spin coating, and dip coating. Electrospinning setup conditions, solvent ratios, damage to fibers, and spin coating speeds were determined. Research was abruptly stopped and …

Self-Assembled Metal Nanoparticle/Polymer Nanocomposites As Nanoreactors For One-Pot Reactions, Andrew Harrison

Theses and Dissertations

Polymer nanoreactors incorporating gold nanoparticle catalysts were self-assembled via Flash Nanoprecipitation. The incorporated gold nanoparticles maintained catalytic activity, which was evaluated using reduction of 4-nitrophenol with sodium borohydride as a model reaction. The diffusion coefficient for 4-nitrophenol was determined by NMR and used to calculate the second Damköhler number, which indicated that the systems were not diffusion limited. Despite similar diffusion coefficients, catalytic performance was strongly affected by the co-precipitant. For example, the apparent reaction rate per surface area using castor oil was over 8-fold greater than polystyrene. Thus, we measured the partition coefficient of 4-nitrophenol between water and castor …

Time-Dependent Reliability Framework For Durability Design Of Frp Composites, Rajneesh Kumar Bharil

Graduate Theses, Dissertations, and Problem Reports (ETD)

The life-cycle performance, durability, and aging characteristics of Fiber Reinforced Polymer (FRP or Structural Composites) have been of keen interest to the engineers engaged in the FRP design, construction, and manufacturing. Unlike conventional construction materials such as steel and concrete, the design guidelines to account for the aging of FRP are somewhat scattered or not available in an approved or consistent format. Loss of strength over time or aging of any structural material should be of concern to engineers as the in-service lifespan of many engineering structures is expected to exceed 100 years. Use of durability strength-reduction factors or factors …

Innovative Sustainable Wood Preservatives From Pulp And Paper Industry Byproduct, Raisa Carmen Andeme Ela

Dissertations, Master's Theses and Master's Reports

In the modern forest industry, the need for bio-based, renewable, and environmentally-benign wood preservatives is increasing. Preservatives are used to prevent or limit decay and there has been an increasing interest in developing wood preservatives from renewable materials. To support the need for bio-based, environmentally-friendly preservatives, this work employed kraft lignin as a raw material to produce a novel bio-based wood preservative.

For the first project, a statistical design of experiments approach in Minitab® was used to study how fractionation process variables during acid precipitation of lignin influence the lignin mass yield and characteristics. After precipitating lignin from black liquor, …

Ph-Sensitive Oxygen Release Microspheres To Enhance Cell Survival In Ischemic Condition, Zhongting Liu

McKelvey School of Engineering Graduate Student Theses & Dissertations

Ischemic diseases such as myocardial infarction, stroke and limb ischemia are severe cardiovascular diseases with high rate of death and millions of people suffered from these diseases. Under ischemic environment, cells die due to deficient supply of nutrient and oxygen. To regenerate ischemic tissues, stem cell therapy is a promising approach because stem cells can differentiate into cells necessary for the regeneration. However, stem cell therapy has limitations. For example, few cells can survive under harsh ischemic environment. To enhance stem cells survival, implantation of oxygen release microspheres to sustained supply cells with oxygen represents an effective strategy. Previously, our …

Formulation Optimization Effects On Mechanical And Rheological Properties Of Filled Polysiloxanes, Kevin Mcnay

Electronic Theses & Dissertations

Polysiloxanes are a class of high-performance polymeric materials that are used in a wide variety of applications, including O-rings, gaskets, sealants, coatings, and adhesives. These materials have high temperature resistances as well as flexibility at low temperatures. This is due to the bond between the oxygen and silicon atom, a bond that requires a high dissociation energy to break. However, their elastomers, which can be obtained by crosslinking linear precursors using various crosslinkers, generally exhibit low strength and have poor mechanical properties unless reinforced. Therefore, fillers, additives, UV-stabilizers, and anti-oxidants are often incorporated in order to improve the resulting properties. …

The Effect Of Precursor Design And Processing On The Semi-Crystalline Morphologies Of Polyacrylonitrile-Based Carbon Fiber, Katelyn Cordell

Dissertations

Basic research to control the morphology of polyacrylonitrile (PAN)-based carbon fiber is crucial for next generation composites as it determines their mechanical properties and final use. Poor molecular design of PAN-based precursors and fiber processing causes morphological defects and mechanical limitations.^1,2 This research focused on utilizing the controlled polymerization technique, reversible addition-fragmentation chain transfer (RAFT), of novel acrylamide comonomers to afford well-defined precursors with precisely controlled molecular design. This controlled RAFT technique improved the overall precursor graphitic structure as evident by the increased extent of stabilization and reduced activation energy as compared to precursors prepared by traditional free radical …

Development Of Forward Osmosis Based Separations: A Novel Approach In Membrane Technology, Yu-Hsuan Chiao

Graduate Theses and Dissertations

Tackling the worldwide severe water shortage, the membrane technology is considered to be the most efficient approach and hence, used widely as a cost-effective sustainable solution. “Forward osmosis (FO)” has been the major attention in recent time. FO uses osmotic pressure as the driving force to draw the water passing the membrane and achieve the desired separation performance. In general, it is considered to be a process with tremendous potential to resolve the present-day water shortage with extremely low energy consumption. However, the challenges of membrane and draw solution regeneration associated with FO processes must be conquered prior to their …

Decorative Articles Based On Polymeric Materials, Yaser M. Asal Mr., M. A. Radwan, Hany A. Elazab Dr, Bassant Hussein, Mohamed A. Sadek

Chemical Engineering

The aim of the research is to create decorative articles based on polymeric materials, study the effects of fillers and the type of moulds that it can cope with the exothermic reaction nature of resin to create a scientific background on the usage of the resins in daily life products. The polymeric materials that will be concentrated on are the unsaturated polyester resins and epoxy resins. The unsaturated polyester is of many types and chemical constituents, the used experimentally is a general-purpose type and the epoxy also have different types and the used is a commercially 3D floor coating type. …

Primary Homogeneous Pathways Of Lignin Depolymerization In Gas Phase, Mohamad Barekati-Goudarzi

LSU Doctoral Dissertations

The unique decomposition pathways of hydrolytic lignin (HL) dissolved in acetone/water mixture and dispersed into gas phase has been investigated using two unique reactors. The first one is a non-isothermal continuous wave-IR CO₂ Laser Powered Homogeneous Pyrolysis (LPHP) and the second one is an isothermal Continuous Droplet Evaporation (CDE) reactor. Both of these reactors operated using atmospheric N₂ carrier gas. A temperature region of 400 – 550°C, and various residence time of 0.12-2 sec were chosen for CDE reactor. The temperature distribution in the LPHP reactor was evaluated via thermocouple measurements and validated by the method of “chemical …

Hydrothermal Preparation Of Palladium Supported On Magnetite For Catalysis Applications, Saddam Alaskary

Chemical Engineering

Herein, versatile, and reproducible method to prepare Pd/Fe3O4 via hydrothermal synthesis. The vital role of this catalyst is in its potential use in CO oxidation catalysis. The Pd/Fe3O4 shows a distinctive activity. TEM images confirmed that Pd nanoparticles of 8-12 nm have a well dispersion on the surface of magnetite (Fe3O4). Moreover, the prepared catalyst is recycled with remarkable catalytic activity. This outstanding activity is mainly a direct result of the strong metal-support interaction. The defect sites in the reduced iron oxide act as nucleation centers that enable anchoring of Pd nanoparticles leading to prevention of agglomeration.

Evaluation Of Biodegradability Characteristics Of Cellulose-Based Film As Per Is/Iso 14855-1, Narayan C. Saha Dr, Gaurav Madhu Dr, Diksha B. Kadu Ms

Journal of Applied Packaging Research

Biodegradable polymers (especially those derived from plant sources) begin their lifecycle as renewable resources, usually in the form of starch or cellulose. In this paper, the evaluation of biodegradability of cellulose-based polymer film under controlled composting conditions as per the guidelines of IS/ISO 14855 (Part-1) standard has been described. Microcrystalline cellulose (MCC) powder was taken as positive-control polymer. The apparatus used to analyse the degree and rate of biodegradation was developed indigenously. The validation of the biodegradability testing apparatus was also performed as per the prescribed test method given in IS/ISO 14855-1.