Chemical Engineering Commons^™

Biodiesel Production From Castor Oil: Mixing Optimization During Transesterification, Yaser M. Asal Mr, Islam M. Al-Akraa, Ahmad M. Mohammad, Hassan E. Hisham

Chemical Engineering

With the growing warning for accrediting the traditional combustion of fossil fuels for energy production, not only for their limited supply but also for their environmental risks (air pollution, climate change, …. etc), it became necessary to realize alternative greener and abundant sources for energy. Instead, the interest to sustain biodiesel for the energy production has recently been renewed as a replacement for petroleum diesel in conventional diesel engines. This was due to its renewable nature, low toxicity, high degradability and unique physical properties (high flash points & lubrication). Castor oil, in particular, appeared promising for biodiesel production with extremely …

Castor Oil Conversion To Biodiesel: A Process Simulation Study, Yaser M. Asal Mr, Islam M. Al-Akraa, Ahmad M. Mohammad, Razan Aymen

Chemical Engineering

The aim of this study is to highlights the importance to shift from the use of traditional fossil fuels to biodiesel as a clean energy source. A simulation study has been conducted using ASPEN HYSIS software for the biodiesel production form castor oil. The simulation was run and the properties of the produced biodiesel were highlighted. The optimum conditions resulted in 88 % conversion.

Reverse Cationic Flotation Of Hematite, Natalia Parra Alvarez

Dissertations, Master's Theses and Master's Reports

The reverse cationic flotation of hematite is the most common method to process hematite ores. The goal of this research is to understand the impact of fundamental water and surface effects to enable the optimization of the flotation process. At present, reverse cationic flotation is performed using a single chemical as both collector and frother. Excessive amounts of frother or collector should lead to diminished performance. This research investigates this phenomenon by replacing some of the collector with frothers. It was found that flotation recovery can be improved up to 2.5wt% via 10% replacement with methyl isobutyl carbinol (MIBC). Since …

Application Of Sla 3d Printing For Polymers, Taylor Wilson

Williams Honors College, Honors Research Projects

Stereolithography is a type of 3D printing that allows liquid photopolymer resin to be cured into layers that make up a 3D object. Creation of such resins for these purposes can require a significant amount of time to test and develop, and commercial resins also require some amount of testing for printer settings before use. This paper reviews how stereolithography works, the materials used, and experimentation done to compare the resin properties to the determined curing times. Using several commercially available resins, varying base exposure and layer exposure times were used to determine the lowest possible curing time that gave …

Itraconazole Nanocomposites Prepared Via Rotary Evaporator Drying Of Nanomilled Suspensions, Alexander Santos Coelho

Theses

The aim of this study is to explore the feasibility of rotary evaporation for drying wetmilled drug suspensions as a novel approach to produce drug nanocomposites that exhibit fast redispersion and immediate drug release. To this end, the physical stability of the nanomilled itraconazole (drug) suspensions, a.k.a., nanosuspensions, during the milling and storage; the drying of the itraconazole nanosuspensions via the rotary evaporator; and the type/loading of various polymers/surfactants (dispersants) on aqueous redispersion and drug release from the nanocomposites were examined. Our results suggest that smaller drug particle size, owing to nanomilling, and smaller nanocomposite particle size, owing to optimized …

An Introductory Study Of Coal Fly Ash Enhancement For Heavy Metal Removal In Wastewater Treatment., Samuel T. Romes

Electronic Theses and Dissertations

Coal Combustion Products are the materials that remain after pulverized coal is burned to generate electricity. The fine portion, fly ash, has many re-use capabilities across various industries. Most recent data shows that approximately 60% of fly ash produced in the United States was used with the largest re-use being concrete additives. This work aims to enhance fly ash via hydrothermal treatment in order to expand the re-use capabilities of the material. These materials were tested as adsorbents for heavy metal removal from wastewater samples. The metals tested for removal were Copper (II) Acetate, Cadmium Chloride, Boric Acid, Sodium Selenite, …

Scalable Synthesis Of Alumina Nanowires By Wet Chemical Method., Luis N Moreno

Electronic Theses and Dissertations

To satisfy an increasing demand for large-scale processes for producing alumina nanomaterials, a wet chemical method was evaluated. A potassium salt precursor was combined with aluminum to produce alumina – based nanowires. Compared with current methods such as thermal oxidation, sol-gel, and laser ablation, this method is highly scalable due to relatively low energy requirements and the ability to carry out the primary reaction under ambient conditions. The nanowire samples were evaluated using SEM, XRD, BET, and TEM to confirm morphology, phases present, and surface area. A porous nanowire structure was confirmed which has a BET surface area of 324.6 …

Entrepreneurially Minded Learning In The Unit Operations Laboratory Through Community Engagement In A Blended Teaching Environment, Erick S. Vasquez, Kelly Bohrer, Abraham Noe-Hays, Arthur Davis, Matthew Dewitt, Michael J. Elsass

Chemical and Materials Engineering Faculty Publications

Online and blended learning opportunities in Chemical Engineering curriculum emerged due to COVID-19. After eight weeks of in-person Unit Operations Laboratory sessions, a remote-learning open-ended final project was assigned to student teams. The assignment involved aspects related to entrepreneurial-minded learning (EML) and community-based learning (CBL). Results show correlations between self-directed learning and the EML framework. Continuous support and involvement of a community partner correlate to students' m

Anti-Corrosion Protection Of Metal Parts Of Transportation Equipment With A Polymer Coating Based On Epoxiurethane, Aida Barkhanadjyan, Ravshan Khakimov, Botir Ibragimov, Oybek Vafayev, Dmitriy Ayrapetov

CHEMISTRY AND CHEMICAL ENGINEERING

Automotive vehicles are constantly exposed to corrosion processes, and the durability of metal parts depends on the intensity of corrosion. The loss of metals from corrosion is 8-10% of the initial metal mass. In total, losses from corrosion are 4-6% of national income in many countries. This indicates the need for research and the importance of scientific and technical work in this area. This can be achieved by developing a technology for producing anticorrosive compounds and applying them as protective coatings. The anticorrosive protection of a coating synthesized on the basis of local raw materials - epoxyurethane with an additive …

Analytical Model For Electromagnetic Induction In Pulsating Ferrofluid Pipe Flows, Huiyu Wang, John G. Monroe, Swati Kumari, Serhiy O. Leontsev, Erick S. Vasquez, Scott M. Thompson, Matthew J. Berg, Dibbon Keith Walters, Keisha B. Walters

Chemical and Materials Engineering Faculty Publications

No abstract provided.

Wetting And Drying Dynamics For Tio2 With Pbs Quantum Dots., Kelly M. Lee

Electronic Theses and Dissertations

Initial solar cells utilized silicon and alloys for their economic viability. Photoelectrochemical photovoltaic cells were discovered with technological advancement which increased solar efficiency and further improved economic feasibility leading to quantum dot sensitized solar cells. Lead sulfide quantum dots and titanium dioxide were studied for wetting and drying effects. Zeta potential, pH values, SEM, and optical microscopes quantified or observed the colloidal suspension and dried sample behavior. Combined mixtures of lead sulfide and titania were dried at 3.6 pH and 12.56 pH values. This due to the observed zeta potential isoelectric point of titania, and behavior showed increased stability occurring …

The Study Of Copper Corrosion Mechanisms Using Electrochemical Experimental Techniques., Evan Grimm

Electronic Theses and Dissertations

The purpose of this study was to discover and thoroughly explain the corrosion mechanisms of copper in saltwater, tap water and deionized water, and to apply these methods and findings when testing the corrosion mechanisms of other materials. The experimental procedure consisted of measuring the open circuit potential, electrochemical impedance spectroscopy, linear sweep voltammetry, and Tafel analysis.

The copper was found to corrode at a greater rate in saltwater, followed by tap water then deionized water, with a larger difference between saltwater and tap water than between tap water and deionized water. Each reaction was found to be both kinetically …

Mixed Metal Oxide Nanowires Via Solid State Alloying., Veerendra Atla

Electronic Theses and Dissertations

Mixed metal oxide materials with composition control find applications in energy conversion and storage processes such as heterogenous catalysis, photoelectrochemical catalysis, electrocatalysis, thermal catalysis, and lithium-ion batteries. Mixed metal oxides and/or complex oxides with composition control and in one-dimensional form as nanowires could be interesting to various catalysis applications due to control on single crystal surfaces, active sites, acidity versus basicity site density, and oxygen vacancies. The major challenge is to synthesize mixed metal oxide nanowires beyond binary oxides with composition control. In this dissertation, solid state alloying of binary oxide nanowires with solid and liquid precursors is studied to …

Room Temperature Alkali Treatment Of Rice Straw For Enhanced Enzymatic Hydrolysis., Seth Mains

Electronic Theses and Dissertations

Due to the pollution of fossil fuels due to greenhouse emissions, researchers continue to search for alternative methods that allow for the clean production of energy, fuels, and polymer fibers. A method currently under investigation is the use of lignocellulosic biomass as a solution to current problems with energy and polymer fiber production. Through the process of pretreatment, possibilities for lignocellulosic biomass expand due to improved accessibility of the cellulose and hemicellulose which can be broken down via enzymatic hydrolysis into C5 and C6 sugars such as xylose and glucose. This study investigated the fermentation of the rice straw into …

Facile Fabrication And Characterization Of Kraft Lignin@Fe3o4 Nanocomposites Using Ph Driven Precipitation: Effects On Increasing Lignin Content, Frankie A. Petrie, Justin M. Gorham, Robert T. Busch, Serhiy O. Leontsev, Esteban E. Ureña-Benavides, Erick S. Vasquez

Chemical and Materials Engineering Faculty Publications

This work offers a facile fabrication method for lignin nanocomposites through the assembly of kraft lignin onto magnetic nanoparticles (Fe3O4) based on pH-driven precipitation, without needing organic solvents or lignin functionalization. Kraft lignin@Fe3O4 multicore nanocomposites fabrication proceeded using a simple, pH-driven precipitation technique. An alkaline solution for kraft lignin (pH 12) was rapidly injected into an aqueous-based Fe3O4 nanoparticle colloidal suspension (pH 7) under constant mixing conditions, allowing the fabrication of lignin magnetic nanocomposites. The effects of increasing lignin to initial Fe3O4 mass content (g/g), increasing in ratio from 1:1 to 20:1, are discussed with a complete chemical, structural, and …

A Study Of Hygrometer Based On The Method Of Intracavity Laser Absorption, Abdulaziz Muminovich Nazarov Prof, Mirkomil Mirhidoyat Ogli Xasanov

Chemical Technology, Control and Management

The article presents the results of experimental studies of a fiber-optic humidity sensor, the principle of operation of which is based on the method of intracavity laser absorption. A method of intracavity laser absorption is described, which makes it possible to dramatically increase the sensitivity of the fiber humidity sensor by switching to it. A schematic diagram of a fiber optical humidity sensor using a differential detection scheme and a design of an active ring laser fiber consisting of a diode pump laser, a fiber pump beam splitter, two directional couplers, a measuring ring laser, a ring comparison laser, two …

Bimetallic Catalyst For Lignin Depolymerization, Qishen Lyu

McKelvey School of Engineering Graduate Student Theses & Dissertations

This thesis is motivated by concerns regarding the need to develop more sustainable and economic technologies to meet rising global manufacturing and energy demands. These concerns have renewed governmental, industrial, and societal determination to reduce the world’s dependence on conventional natural resources and has led to considerable research on producing fuels and chemicals from feedstocks other than petroleum. Lignocellulosic biomass represents an abundant and renewable resource that could displace petroleum feedstock producing biofuels and multiple valuable chemical products with reduced greenhouse gas emissions. Lignin is the second abundant biopolymer source in nature and is found almost everywhere. Since the 1950’s, …

Exploration Of The Sludge Biodiesel Pathway, Zachary Christman

Department of Agronomy and Horticulture: Dissertations, Theses, and Student Research

Wastewater sludge is an overlooked source of fat, oil, and grease (FOG) that could be converted into biodiesel. The United States produces about 8 million tons of sludge per year. The disposal cost for this amount of sludge is about 2 billion US dollars. The widespread availability and low cost of sludge compared to other biodiesel raw materials make it an economical choice for a renewable fuel. Using sludge as a raw material can produce 25 to 30 mg per gram of fatty acid methyl ester (FAME); the main component of biodiesel. Sludge biodiesel has the potential of transforming a …

2020-21 Aiche Student Design Competition: Naphtha Processing, Brenna Kathleen Flynn, Hannah Orebaugh, Paul Deaton

Honors Capstone Projects and Theses

No abstract provided.

Economic Feasibility Of Mixed Plastic Waste Pyrolysis Using Twin Reactor System In Northwest Arkansas, Carol Rogers, Patricia Means, Renato Gonzalez, Kaida Sheets, Hayden Townsend

Chemical Engineering Undergraduate Honors Theses

Plastic waste generation is increasing at an unsustainable rate while recycling solutions remain stagnant. As a chemical means of recycling, mixed plastic waste pyrolysis can generate synthetic oil appropriate for use as fuel in power generation from plastic waste that otherwise accumulates in landfills. With the scaling of a commercial plastic pyrolysis process in Northwest Arkansas (NWA) modeled after an operational sawdust pyrolysis unit in Huntsville, Arkansas, economic analysis resulted in 26.3% internal rate of return. Therefore, construction of a commercial mixed plastic-to-fuel pyrolysis plant is economically justified and should be pursued. To effectively implement the proposed design, NWA must …

Household Income And Air Pollution At Public Schools In The United States, Katyland Facas, Kristina Wagstrom

Honors Scholar Theses

Poor air quality at schools may negatively impact students’ academic performance.1 2 3 In this study we look at the relationship between ambient, outdoor air quality and student socioeconomic status at United States public schools. We used free and reduced lunch eligibility, as part of the USDA’s National School Lunch Program, as an indicator of household income. We focus on nitrogen dioxide (NO2), ozone (O3), and particulate matter smaller than 2.5 microns (PM2.5). We used ambient pollutant concentration estimates at census block group resolution (Kim et al.) as the outdoor air pollution concentration at each school.4 We found a positive …

Comparison Of Tensile Properties Of Triaxial Braided Carbon Fiber Composites Made From Vacuum Assisted Resin Transfer Molding (Vartm) And Autoclave Molding, Donald A. Klosterman, Charles Browning

Chemical and Materials Engineering Faculty Publications

Triaxially braided fiber composites are increasingly being used in aerospace, ballistic, and sporting good applications due to their inherent damage tolerance, torsional stability, and cost compared to woven fabrics and unidirectional preforms. There have been numerous publications over the past 15-20 years on the mechanical properties and failure mechanisms of triaxial braided composites. However, most of these have involved panels made with autoclave curing. In the present study, braided carbon fiber composites were made using autoclave curing and vacuum assisted resin transfer molding (VARTM). The goal of the study was to compare the physical and tensile properties of quasi-isotropic panels …

Ethylbenzene Production Case Study And Optimization, Brandon Borek

Honors Theses

The objective of this project was to investigate the process of producing ethylbenzene from the liquid-phase reaction of ethylene and benzene and perform parametric and topological optimizations to increase the net present value of the production facility. To do so, the base case conditions of the process were modeled and quantified economically followed by an investigation into the existing process to determine conditions that could be altered to improve the economic viability of the project. After optimizing the parametric conditions and topology of the process, the net present value of the project was increased by 305 million dollars to 191 …

Aveva Competition 2021: Dimethyl Ether Production Process, Nicholas Gaouette

Honors Theses

The following study was conducted to assess the economic and process feasibility of a dimethyl ether (DME) production process. A portion of the methanol produced by an existing facility would be used to produce DME through a dehydration reaction. DME production is being considered as a means to compensate for lost methanol revenue, as methanol prices have recently decreased and an excess supply is present on the open market.

The first milestone in the study was the construction of a working process model within AVEVA Process Simulation. This steady-state process model would provide information essential to further design and optimization …

Design And Analysis Of A Process To Convert Methanol Into Dimethyl Ether, Elisa M. White

Honors Theses

A recent economic downturn led to the loss of a contract for a company that sells methanol. The company has two options to recover some of the profit lost from the contract termination. One option is to sell the excess methanol at the spot market price, and the second option is to implement a process to convert the excess methanol into dimethyl ether. This project investigated the implementation of a process to convert the methanol from the lost contract into dimethyl ether. The process was simulated in AVEVA Process Simulation to estimate the size of equipment needed. A toller provided …

Peptoid-Functionalized Gold Nanoparticles For Zika Virus Envelope Protein Detection, Meagan Olsen

Chemical Engineering Undergraduate Honors Theses

Detection and identification of viral pathogens is essential in providing effective and rapid medical treatment. Well-established detection methods can be expensive, slow, and sometimes unable to provide the needed sensitivity and specificity. The Zika virus is one clinically relevant pathogen that cannot be easily identified due to cross-reactivity with other viruses from the same family. Electrochemical sensors enhanced with peptoid-functionalized gold nanoparticles (AuNPs) are an alternative to traditional techniques that offers rapid, accurate, label-free pathogen detection for point-of-care diagnostics. To this end, a peptoid capable of binding to the Zika virus envelope protein was developed and its binding affinity for …

Garver Industrial Design Project: Designing A Full-Scale Reverse Osmosis Water Treatment Facility For The City Of Lawton, Oklahoma, Kayliana Warden, Marlando Collins, Sandrina Depaz, Reid Eakin, Reed Leasure, Vera Rodriguez

Chemical Engineering Undergraduate Honors Theses

A groundwater treatment facility was designed for Lawton, Oklahoma to address potential water scarcity due to drought conditions in southwest Oklahoma. The facility will produce five million gallons per day (MGD) of treated water. The plant will have the capacity of treating 4,085 gallons per minute of influent water at an 86% recovery. The water to be treated will come from the Arbuckle-Timbered Hills Aquifer. Studies have been conducted around the aquifer to identify the best well site locations.

A centralized treatment facility using reverse osmosis filtration as the main treatment technology has been designed. To prevent reverse osmosis membrane …

Ceramic Tiles Production From Cullet And Agricultural Wastes Obtained From Wheat And Sugarcane Cultivation, Mai H. Roushdy

Chemical Engineering

Agricultural wastes are a big source for environmental pollution so it’s a good choice to recycle them so as to get an environmental and economic benefit. The purpose of this research is to determine the possibility of recycling two types of agriculture wastes obtained from wheat and sugarcane cultivation in addition to broken glass (cullet) as raw materials for ceramic wall tiles production. The used agriculture wastes are the agricultural residue obtained from wheat and sugarcane cultivation. The experimental work starts with performing XRF and sieve analysis for all raw materials. Ceramic wall tiles specimens were made with dimensions 110.4 …

Design, Analysis, And Optimization Of A Process To Produce Dimethyl Ether From Methanol, Thomas Mathwig

Honors Theses

The company that the engineering team works for is facing a contract loss with one of its customers of methanol. To avoid economic losses, a process has been proposed for converting the unused methanol to dimethyl ether (DME) through a dehydration reaction. After a preliminary simulation of the base case and optimization of the distillation column, an Equivalent Annual Operating Cost (EAOC) of $140,000 was calculated for the column. The EAOC was the sum of the annualized capital investment and the annual operating cost. Determining the process to be worth pursuing, a Toller was brought in to provide rental equipment …

Detection And Aggregation Of Listeria Monocytogenes Using Polyclonal Antibody Gold-Coated Magnetic Nanoshells Surface-Enhanced Raman Spectroscopy Substrates, Robert T. Busch, Farzia Karim, Yvonne Sun, H. Christopher Fry, Yuzi Liu, Chenglong Zhao, Erick S. Vasquez

Chemical and Materials Engineering Faculty Publications

Magnetic nanoshells with tailored surface chemistry can enhance bacterial detection and separation technologies. This work demonstrated a simple technique to detect, capture, and aggregate bacteria with the aid of end-functionalized polyclonal antibody gold-coated magnetic nanoshells (pAb-Lis-AuMNs) as surface-enhanced Raman spectroscopy (SERS) probes. Listeria monocytogenes were used as the pathogenic bacteria and the pAb-Lis-AuMNs, 300 nm diameter, were used as probes allowing facile magnetic separation and aggregation. An optimized covalent bioconjugation procedure between the magnetic nanoshells and the polyclonal antibody was performed at pH six via a carbodiimide crosslinking reaction. Spectroscopic and morphological characterization techniques confirmed the fabrication of stable pAb-Lis-AuMNs. …