Chemical Engineering Commons^™

Medium Density Fibreboard Made Of Acetylated Sludge From Paper Mill, Luthfi Hakim, Evalina Herawati, I Nyoman Jaya Wistara

Makara Journal of Technology

Medium Density Fibreboard Made of Acetylated Sludge from Paper Mill. Research of using sludge as raw material for making medium density fibreboard (MDF) was useful to create additional value of sludge. The objective of the research was to evaluate physical properties, mechanical properties, and durability of MDF from acetylated sludge in 4 levels of acetate anhydride (0%, 3%, 5%, and 7%) with 3 replicates. The MDF was made using dry process. After materials were mixed with adhesives, they were pressed using hotpress under 170 oC temperature and 45 Pa pressure for 25 minutes. The size of the MDF sample was …

Cassava Pulp As A Biofuel Feedstock Of An Enzymatic Hydrolysis Proces, Djuma’Ali Djuma’Ali, Nonot Soewarno, Sumarno Sumarno, Dyah Primarini, Wahono Sumaryono

Makara Journal of Technology

Cassava pulp, a low cost solid byproduct of cassava starch industry, has been proposed as a high potential ethanolic fermentation substrate due to its high residual starch level, low ash content and small particle size of the lignocellulosic fibers. As the economic feasibility depends on complete degradation of the polysaccharides to fermentable glucose, the comparative hydrolytic potential of cassava pulp by six commercial enzymes were studied. Raw cassava pulp (12% w/v, particle sizeμm) hydrolyzed by both commercial pectinolytic (1) and amylolytic (2) enzymes cocktail, yielded 70.06% DE. Hydrothermal treatment of cassava pulp enhanced its susceptibility to enzymatic cleavageas compared to …

Alos/Palsar Image Processing Using Dinsar And Log Ratio For Flood Early Detection In Jakarta Based On Land Subsidences, Dodi Sudiana, Mia Rizkinia

Makara Journal of Technology

Flood that occurred in Jakarta is not only influenced by rainfall, urban planning system and drainage alone, but also may be involved land subsidence (LS). LS is possible in because Jakarta stands on top of layers of sediments and the presence of ground water consumption in very large quantities. In this research, the Advanced Land Observing Satellite (ALOS)/Phased Array type L-band Synthetic Aperture Radar (PALSAR) data was processed to determine the level of LS in Jakarta area and its relation to flood potential area. Differential interferometry method (DInSAR) was performed on two PALSAR data with different acquisition years, i.e. 2007 …

Analytical And Computational Simulation Approaches To Design Low Energy Glass Block, Floriberta Binarti, Agustinus Djoko Istiadji, Prasasto Satwiko, Priyo Tri Iswanto

Makara Journal of Technology

Analytical and Computational Simulation Approaches to Design Low Energy Glass Block. An environmentally friendly process was developed to produce a low embodied energy glass block from waste glasses. The energy efficiency of the glass block is represented by its thermal conductance (U)

Improvement Of High Temperature Oxidation Of Low Carbon Steel Exposed To Ethanol Combustion Product At 700 °C By Hot-Dip Aluminizing Coating, Mohammad Badaruddin

Makara Journal of Technology

Low carbon steel (AISI 1005) was coated by hot-dipping into a molten Al-10% Si bath at 700 °C for 18s. After hotdipping treatment, the coating layers consisted of Al, Si, FeAl3, τ5-Fe2Al8Si, and Fe2Al5. The bare steel and the aluminized steel were isothermally oxidized at 700 °C in ethanol combustion product at atmospheric pressure for 49 h. The aluminized steel shows good performance in high temperature oxidation because the formation of Al2O3 layer on the coating surface. The growth of iron oxide nodules on the surface coating was accelerated by rapid outward diffusion of Fe-ions due to the presence of …

Establishment Code Hand Palm (Palm Code) 2d Gabor-Based Method, I Ketut Gede Darma Putra, Wira Bhuana, Erdiawan Erdiawan

Makara Journal of Technology

Establishment Code Hand Palm (Palm Code) 2D Gabor-Based Method. Palmprint is relatively new in physiological biometrics. Palmprint ROI segmentation and feature extraction are two important issues in palm print recognition. This paper introduces two steps in the center of mass moment method for ROI segmentation that will be applied in the Gabor 2D filter to obtain palm code as palmprint feature vector. Normalized Hamming distance was used to measure the similarity degrees of two feature vectors of palmprint. The system was tested using database 1000 palmprint images generated from 5 samples from each of the 200 persons randomly selected with …

Flutter Analysis Of Rx-420 Balistic Rocket Fin Involving Rigid Body Modes Of Rocket Structures, Novi Andria

Makara Journal of Technology

Flutter Analysis of RX-420 Balistic Rocket Fin Involving Rigid Body Modes of Rocket Structures. Flutter is a phenomenon that has brought a catastrophic failure to the flight vehicle structure. In this experiment, flutter was analyzed for its symmetric and antisymmetric configuration to understand the effect of rocket rigid modes to the fin flutter characteristic. This research was also expected to find out the safety level of RX-420 structure design. The analysis was performed using half rocket model. Fin structure used in this research was a fin which has semispan 600 mm, thickness 12 mm, chord root 700 mm, chord tip …

Flexible Connection Elastomeric Rubber As A Pounding Resisting Element Between Two Adjacent Buildings, Yuskar Lase, James Jatmiko Oetomo

Makara Journal of Technology

Flexible Connection Elastomeric Rubber as a Pounding Resisting Element between Two Adjacent Buildings To solve pounding problem of two adjacent buildings, structural designer usually employs a dilatation between the structures or make the two structures as a monolith structure. Other alternative is by using an elastomeric rubber as a pounding resisting element between the two structures. Effectiveness in applying elastomeric rubber component as flexible connection of two adjacent structures is the main focus of this paper. Various simulations such as structure models, earthquake excitations and openings in gap element are studied. Observation of maximum structural responses will be performed for …

Optimation Of Nitrogen And Phosphorus In Azolla Growth As Biofertilizer, Hany Handajani

Makara Journal of Technology

Nitrogen is one of the most important minerals for living organisms. Azolla is known as a small water fern which can fix nitrogen through the symbiotic association with the blue green algae Anabaena. Experimental studies were carried out in the glass house, investigating the growth of Azolla using different levels of nitrogen and phosphorus in the media. The experiment used 12 treatments with 3 levels of nitrogen (0, 5, and 10 mg atom/L) and 4 levels of phosphorus (0, 10, 20, and 30 mg atom/l) in a factorial design with 3 replicates. The results show that the highest biomass for …

Application Of Principal Component Proximity Transform And Geostatistics Methods For Volume Shale Distribution As Reservoir Characreristic Imaging In Seismic 3d, Nur Islami

Makara Journal of Technology

Application of Principal Component Proximity Transform and Geostatistics Methods for Volume Shale Distribution as Reservoir Characreristic Imaging in Seismic 3D. Principal component proximity transform (PCPT) technique was used to predict the content of volume shale into seismic data in reservoir modeling framework. The goal in this research is to get the volume shale imaging in three dimensions and allow for reservoir modelling. The reservoir modelling requires an integrated quantitative and qualitative data sources collected separately, such as well and seismic data. Integrating PCPT and Geostatistic methods can generate the detail information for characterization of reservoir’s properties. Finally, it shows that …

Antibacterial Activity Of Papaya Leaf Extracts Against Pathogenic Bacteria, Elisa Friska Romasi, Jessica Karina, Adolf Jan Nexson Parhusip

Makara Journal of Technology

It was reported that the extracts of papaya leaves could inhibit the growth of Rhizopus stolonifer. Antibacterial activity of Carica papaya leaf extracts on pathogenic bacteria was observed in this study. Papaya leaves were extracted by using maceration method and three kinds of solvents: ethanol, ethyl acetate, and hexane. Papaya leaf extracts were tested against Bacillus stearothermophilus, Listeria monocytogenes, Pseudomonas sp., and Escherichia coli by agar diffusion method. The objectives of this study were to determine extract ability against pathogenic bacteria, to observe the influence of pH, NaCl, and heat on extracts ability, and to observe extract ability against B. …

Giant Magnetostriction In Annealed Co1-XFeX Thin-Films, Dwight Hunter, Will Osborn, Ke Wang, Nataliya Kazantseva, Jason R. Hattrick-Simpers, Richard Suchoski, Ryota Takahashi, Marcus L. Young, Apurva Mehta, Leonid A. Bendersky, Same E. Lofland, Manfred Wuttig, Ichiro Takeuchi

Faculty Publications

Chemical and structural heterogeneity and the resulting interaction of coexisting phases can lead to extraordinary behaviours in oxides, as observed in piezoelectric materials at morphotropic phase boundaries and relaxor ferroelectrics. However, such phenomena are rare in metallic alloys. Here we show that, by tuning the presence of structural heterogeneity in textured Co_1−xFe_x thin films, effective magnetostriction λeff as large as 260 p.p.m. can be achieved at low-saturation field of ~10 mT. Assuming λ100 is the dominant component, this number translates to an upper limit of magnetostriction ofλ100≈5λeff >1,000 p.p.m. Microstructural analyses …

A Modified Surface On Titanium Deposited By A Blasting Process, Caroline O' Sullivan, Peter O'Hare, Greg Byrne, Liam O'Neill, Katie B. Ryan, Abina M. Crean

Publications

Abstract

: Hydroxyapatite (HA) coating of hard tissue implants is widely employed for its biocompatible and osteoconductive properties as well as its improved mechanical properties. Plasma technology is the principal deposition process for coating HA on bioactive metals for this application. However, thermal decomposition of HA can occur during the plasma deposition process, resulting in coating variability in terms of purity, uniformity and crystallinity, which can lead to implant failure caused by aseptic loosening. In this study, CoBlast™, a novel blasting process has been used to successfully modify a titanium (V) substrate with a HA treatment using a dopant/abrasive regime. …

Evaluation Of Cathode Materials For Low Temperature (500-700c) Solid Oxide Fuel Cells, Alexander M. Lassman

Master's Theses

Solid oxide fuel cells (SOFC) have gained a great deal of interest, due to their potential for high efficiency power generation and ability to utilize hydrogen fuel, as well as various hydrocarbon-based fuels. A recent trend in SOFC development has been towards lower operating temperatures (500-700°C), which can substantially reduce the cost and complexity of the system. This thesis presents an investigation into state of the art Ba- and La- based cathode materials for use in low temperature (500-700°C) solid oxide fuel cells.

Synthesis of A-site deficient [A=0.97] Ba_0.5Sr_0.5Co_0.8Fe_0.2O₃ (BSCF) was …

Electrochemical Performance Of Tin Dioxide/Carbon Xerogel Composites As Anode Materials For Lithium-Ion Batteries, Xiao-Jing Liu, Lin-Lin Qin, Yi-Ning Shi, Ming-Sen Zheng, Quan-Feng Dong

Journal of Electrochemistry

The tin dioxide/carbon xerogel composites were synthesized by using vacuum infiltration method. Structural characterization and morphology of the composites were investigated by using XRD, TEM and SEM techniques. BET test was performed to determine the pore size distributions of carbon xerogels and the composites. The results showed that the nano-sized SnO₂ particles (5~10 nm) were encapsulated in the pores of carbon xerogels. During the electrochemical tests the SnO₂ in the composites exhibited capacity retention of 61.9% after 100 cycles of charge-discharge tests at 100 mA/g.

Synthesis And Electrochemical Behaviors Of Li2Coxmn1-XSio4 As A Cathode Material For Lithium-Ion Batteries, Lin Wang, Dong-Ping Lv, Yong Yang

Journal of Electrochemistry

We have successfully synthesized Li₂Co_xMn_1-xSiO₄/C (x=0, 0.1, 0.3, 0.5, 1)/C composites using hydrothermal assisted sol-gel process and ball-milling method. The results of X-ray diffraction show that the solid solutions of Li₂Co_xMn_1-xSiO₄ can be achieved when x≤0.3. The initial capacities increase from 70 mAh·g^-1 of Li₂MnSiO₄/C to 105 mAh·g^-1 of Li₂Co_0.3Mn_0.7SiO₄/C. Cyclic Voltammetry (CV) curves show that the replacement of Mn with Co can reduce the electrochemical polarization, making the insertion-extraction reaction …

Synthesis Of Limnpo4/C Used As Cathode Material For Lithium Ion Batteries, Xin Yang, Xue-Wu Liu, Gui-Chang Liu, Zhi-Cong Shi, Xin Li, Guo-Hua Chen

Journal of Electrochemistry

The LiMnPO₄/C composites were prepared using a solid-state reaction with addition of the resorcinol formaldehyde resin as the carbon source. The effects of reaction temperature and time on the crystal structure, morphology and electrochemical properties of the LiMnPO₄/C composites were investigated. The results show that the best performance was achieved with the LiMnPO₄/C composites synthesized at 600 ^oC for 12 h which had the particle sizes about 100~200 nm. The initial discharge capacities were 121.6 mAh·g^-1 at 0.02C, 110 mAh·g^-1 at 0.1C and more than 60 mAh·g^-1 at 1C. An …

Determining A Method For Rendering Low Cost Cdse(Zns) Core(Shell) Quantum Dots Aqueous Soluble Via Amphiphilic Polymer Wrapping, Patrick Mcbride

Materials Engineering

Herein is described the procedure of two amphiphilic polymer wrapping techniques that may be employed for obtaining aqueous soluble quantum dots (QDs) for use in biological fluorescent imaging applications. The advent of QDs has led to new nanoscale fluorescent materials that exhibit unparalleled quantum yields (QYs), high resistance to photobleaching, tunable emissions, and
absorption over a large optical range. However, the QD synthesis employed here at Cal Poly to obtain bright, photostable CdSe(ZnS) core(shell) QDs involves the use of organic solvents and surfactants, leading to hydrophobic QDs. Since all of biology relies on aqueous solubility, this hydrophobicity creates a major …

The Design And Manufacture Of A Microfluidic Reactor For Synthesis Of Cadmium Selenide Quantum Dots Using Silicon And Glass Substrates, Peter Gonsalves

Materials Engineering

A microfluidic reactor for synthesizing cadmium selenide (CdSe) quantum dots (QDs) was synthesized out of silicon and Pyrex glass. Microfabrication techniques were used to etch the channels into the silicon wafer. Holes were wet-drilled into Pyrex glass using a diamond-tip drill bit. The Pyrex wafer was aligned to the etched silicon wafer and both were anodically bonded to complete the microfluidic reactor. Conditions for anodic bonding were created by exposing the stacked substrates to 300V at ~350^oC under 5.46N of force.  Bulk CdSe solution was mixed at room temperature and treated as a single injection. The syringe containing …

Preparation And Electrocatalytic Activity Of The Pt/Wc/Tio2 Composites, Chun-An Ma, Bin Yu, Mei-Qin Shi, Xiao-Ling Lang

Journal of Electrochemistry

TiO₂ was used as the support for preparation of Pt/WC/TiO₂ composite catalyst. The composites were characterized by XRD, SEM and TEM methods. The electrocatalytical activity of Pt/WC/TiO₂ composite for oxidation of methanol was investigated by cyclic voltammetry. Pt/WC/TiO₂ exhibited higher activity compared with that of Pt/TiO₂ and Pt/WC composite catalysts. Based on this we discussed the effects of crystal phases of TiO₂ on the electrocatalytical activity of Pt/WC/TiO₂ composite catalyst.

Electrochemical Capacitive Performance Of Mesoporous Carbon Based Co-Ni Oxides, Zhen-Sheng Yang, Ling-Bin Kong, Li Deng, Yong-Chun Luo, Long Kang

Journal of Electrochemistry

By using defects on the surface of CMK-3 served as nucleation center, Co_0.25Ni_0.75 oxide/C composite was successfully prepared through a simple chemical co-precipitation method. Characterization was carried by using X-ray diffraction, BET and scanning electron microscopy. Results showed that a perfect mesoporous network of interconnected nanoflakes was obtained for Co_0.25Ni_0.75 oxide/C composite and, this material has a less crystallization, interconnected nanoflakes network structure and a narrow mesoporous distribution at about 3~4 nm. The highly dispersed and loosely packed Co_0.25Ni_0.75 oxide/C composite possessed good electrochemical accessibility and fast diffusion rate of OH …

Study On Direct Electro-Oxidation Of Anisaldehyde, Lin-Lin Wu, Ying-Hong Zhu, Shan-Shan Li, Hong-Yan Zeng, Chun-An Ma

Journal of Electrochemistry

The oxidation of anisole on Pt electrode was investigated by cyclic voltammery and constant potential electrolysis. The influence of scan rates, substrate concentration, supporting electrolytes and solvent were considered . The results show that the electro-oxidation process of anisole was irreversible. In this research the sulfuric acid was the best supporting electrolytes and acetone was the best solvent, and the process was controlled by diffusion . The product of constant potential electrolysis was charactered by GC-MS .The results show that the main products was anisaldehyde, and the selectivity was up to 66.5% when using acetone as solvent.

Comparison Of Catalytic Performance On Different Materials Supported Pd Catalysts For Formic Acid Oxidation, Su-Dong Yang, Yan-Yu Liang, Zhu-Liang Wen, Qi-Jun Song, Xiao-Gang Zhang

Journal of Electrochemistry

Graphite oxide (GO) was prepared from by Hummers method. Then the graphene nanosheets supporting Pd catalysts were prepared by a single-step chemical reduction method. The electrocatalytic performance for formic acid oxidation of the prepared Pd/graphene composite was studied as an electrode material in comparison with the composite catalysts based on the other carbons (MWCNTs, SWCNTs, and Vulcan XC-72 carbon black). X-ray diffraction (XRD) and transmission electron microscopy (TEM) measurements indicated that the Pd nanoparticles were well dispersed on the surface of the graphene nanosheets with a small particle size. The electrocatalytic oxidation of formic acid was studied by electrochemically active …

Synthesis And Catalytic Property Of Flaked Spindle-Like Cuo Nanocrystals, Jian-Feng Fan, Li-Qing Li, Yu-Feng Huang, Lou-Zhen Fan

Journal of Electrochemistry

A simple and efficient electrochemical route was developed for the synthesis of flaked spindle-like CuO nanocrystals using aqueous electrolyte and Cu sacrificial anode (graphite as the cathode) in an undivided cell at a constant potential mode under room temperature. The morphologies, structure and component of CuO nanocrystals obtained were characterized by SEM, XRD, respectively. Flaked spindle-like CuO nanocrystals were successfully used to modify a GC electrode to detect H₂O₂ with cyclic voltammetry (CV) and amperometric (AC).The results showed that products were pure monoclinic CuO nanocrystals. The linear range for the determination of hydrogen peroxide is from 1.0 …

Dft Study Of Co2 Reduction To Hydrocarbons On Cu Surfaces, Li-Hui Ou, Sheng-Li Chen

Journal of Electrochemistry

CO₂ reduction on Cu(111) single crystal surfaces was studied using DFT calculations on the reaction energies and the minimum energy paths. The results indicated that the possible reaction paths for CO₂ reduction on Cu(111) surface are CO₂(g) + H* → COOH* → (CO +OH)*, (CO + H)* → CHO*, CHO + H → CH₂O* → (CH_2⁺O)*, CH₂* + 2H* → CH₄ or 2CH₂* → C₂H₄. On Cu(111) surface, the reaction rate is controlled by steps of CH₂O* → (CH_{2 …}

Anode Electrodeposition Of Ti/Mno2 Electrode And Electrocatalytic Oxidization Properties Of Phenol Degradation, Ye Chen, Wen-Li Zhao, Qing Wen

Journal of Electrochemistry

Ti-base manganese dioxide (Ti/MnO₂) electrode was prepared by anodically electrodeposition technology in this paper. The structure of the electrode, the microstructure of the electrode surface and the element composition of the electrode were analyzed by XRD, SEM and EDS. The preparation process parameters of the electrode were studied in detail with the help of the V~logi curve and phenol degradation curve. The Ti/MnO₂ electrode was anodically electrodeposited at current density 4mA•cm^-2, the Mn^{2 +} ions concentration 0.5mol•L^-1 and temperature70℃. The V~logi curve and phenol degradation curve were used to evaluate electrocatalytic oxidization properties …

The Solvent Effectiveness On Extraction Process Of Seaweed Pigment, Warkoyo Warkoyo, Elfi Anis Saati

Makara Journal of Technology

Eucheuma cottonii seaweed is a species of seaweed cultured in Indonesian waters, because its cultivation is relatively easy and inexpensive. It has a wide variety of colors from green to yellow green, gray, red and brown, indicating photosynthetic pigments, such as chlorophyll and carotenoids. An important factor in the effectiveness of pigment extraction is the choice of solvent. The correct type of solvent in the extraction method of specific natural materials is important so that a pigment with optimum quality that is also benefical to the society can be produced. The target of this research is to obtain a high …

The Synergy Of Recombinant Xylanolytic Enzyme On Xylan Hydrolysis, One Asmarani, Bambang Prajogo Eko Wardojo, Ni Nyoman Tri Puspaningsih

Makara Journal of Technology

Microbial xylanases or xylanolytic enzyme have received considerable attention over the last years owing to a multitude of possible applications. These enzymes have potential in the biodegradation of lignocellulosic biomass to fuels, chemicals, fruit juice, animal feed and in improving rumen digestion. More recently, the use of xylanases as bleaching agent in the pulp and paper industry has been suggested to replace of some of the chemicals presently used for this purpose. Such applications could have an important positive impact on the environment. The purpose of this research was determining the synergy of 3 recombinant xylanolytic enzymes (β-xylosidase, exo-xylanase and …

Cradle To Gate Simple Life Cycle Assessment Of Biodiesel Production In Indonesi, Akhmad Hidayatno, Teuku Yuri M. Zagloel, Widodo Wahyu Purwanto, Carissa Carissa, Lindi Anggraini

Makara Journal of Technology

The focus of this research is to analyze potential environmental impact in the supply chain of palm oil biodiesel industries. Simple Life Cycle Assessment (LCA) is applied to analyze impacts, produced by the three main units in the supply chain of Palm-Oil-based Biodiesel, which are Palm Plantation, CPO mill, and Biodiesel Plant. We developed LCA calculation model using spreadsheet software, used to assess a number of input scenarios to evaluate the best scenario, in variation of: land quality, land area and the rate of clearing, land clearing technique and type of the original land. The biggest potential environmental impact is …

Characterization Of Surface Active Shell Charcoal Nyamplung Seeds (Calophyllum Inophyllum Linn), Santiyo Wibowo, Wasrin Syafi, Gustan Pari

Makara Journal of Technology

Characterization of Surface Active Shell Charcoal Nyamplung Seeds (Calophyllum inophyllum Linn). Chemical and physical activation of nyamplung shell with 0%, 5%, and 10% H3PO4 for 60 and 120 minutes has been carried out to prepare activated charcoal. The purpose of this experiment was to look into the characteristic of nyamplung shell activated charcoal surface. Nyamplung shell was carbonized into charcoal, then activated by immersion in H3PO4 solution using 0%, 5% and 10%, for 24 hours, and heated in retort at two temperatures (700 and 800 oC) and two duration (60 and 120 minutes). The material were characterized by fourier transform …