Chemical Engineering Commons^™

The Effect Of Different Fracturing Fluids On The Productivity Of Multi-Staged Fractured Marcellus Shale Horizontal Wells, Vida Gyaubea Matey-Korley

Graduate Theses, Dissertations, and Problem Reports (ETD)

While hydraulic fracturing has undeniably improved the production from oil and gas reservoirs, this technology is not without limitations. The primary hurdles lie in the areas of proppant transport, fluid rheology, and stress management. Despite the extensive research conducted in this domain, there remains a considerable amount of work to be done for comprehensive solutions that account for the complex interactions among fracturing fluid, proppant distribution, and geomechanical conditions. Achieving this will then make room for a holistic and efficient hydraulic fracturing strategy.

This study addresses the above-mentioned problem by examining the impact of fluid type on proppant transport and …

Fugacity-Based Lattice Boltzmann Method For Multicomponent Multiphase Systems, Muzammil Soomro, Luis F. Ayala, Cheng Peng, Orlando M. Ayala

Engineering Technology Faculty Publications

The free-energy model can extend the lattice Boltzmann method to multiphase systems. However, there is a lack of models capable of simulating multicomponent multiphase fluids with partial miscibility. In addition, existing models cannot be generalized to honor thermodynamic information provided by any multicomponent equation of state of choice. In this paper, we introduce a free-energy lattice Boltzmann model where the forcing term is determined by the fugacity of the species, the thermodynamic property that connects species partial pressure to chemical potential calculations. By doing so, we are able to carry out multicomponent multiphase simulations of partially miscible fluids and generalize …

Mechanisms Of Emulsion Destabilization: An Investigation Of Surfactant, Stabilizer, And Detergent Based Formulations Using Diffusing Wave Spectroscopy, Jordan N. Nowaczyk

Theses and Dissertations

Conventional approaches for studying emulsions, such as microscopy and macroscopic phase tracking, present challenges when it comes to establishing detailed mechanistic descriptions of the impact of emulsifier and stabilizer additives. Additionally, while a combination of sizing methods and macroscopic phase tracking can provide insights into droplet size changes and concentration, the use of multiple measurements can be cumbersome and error-prone. It is the focus of this work, to present a new method for studying water in oil (W/O) emulsions that involves using diffusing wave spectroscopy (DWS) to examine the impact of three different surface stabilizing additives at varying concentrations. By …

Mechanical And Adhesive Properties Of Supramolecular, Mussel-Inspired Hydrogels, Daniel Darby

Theses and Dissertations--Chemical and Materials Engineering

The exceptional mechanical and adhesive properties of mussel byssal threads come from supramolecular interactions of ligands found in the proteins comprising them. Ligands can form hydrophobic interactions, π-π stacking interactions, and hydrogen bonds, but the strongest supramolecular interaction they demonstrate is metal-ligand coordination. Specifically, Histidine (His-) and nitrodopamine (nDOPA) ligands coordinate to metals in a bidentate fashion and take on tris-, bis-, and mono- modalities (3, 2, or 1 ligand per ion, respectively). The distribution of these modalities is controlled by equilibrium thermodynamics. These same ligands can be used as crosslinks in supramolecular hydrogel networks. Supramolecular hydrogel networks are dissipative, …

Effect Of Hydrogen Sulfide Content On The Combustion Characteristics Of Biogas Fuel In Homogenous Charge Compression Ignition Engines, Mohammad Alrbai, Adnan Darwish Ahmad, Sameer Al-Dahidi, Ahmad M. Abubaker, Loiy Al-Ghussain, Hassan S. Hayajneh, Nelson Akafuah

Institute of Research for Technology Development Faculty Publications

The use of biogas fuel in homogeneous charge compression ignition (HCCI) engines has been promoted recently due to the environmental advantages. However, hydrogen sulfide (H2 S) forms a non-environment friendly content and biogas impurity that its removal is associated with high costs. In this study, the effect of using biogas fuel in the HCCI engines under different operating conditions is investigated to shed light on the best scenarios of biogas combustion, even with the presence of H2S contents. A modified reaction mechanism is introduced by considering the re- actions of H2 S with other species in the air-fuel mixture. The …

Artificial Neural Network For Predicting Heat Transfer Rates In Supercritical Carbon Dioxide, Vinusha Dasarla Giri Babu

Doctoral Dissertations and Master's Theses

Supercritical carbon dioxide as a working fluid in a closed Brayton cycle is proving to be more efficient than a conventional steam-based Rankine engine. Understanding the heat transfer properties of supercritical fluids is important for the design of a working engine cycle. The thermophysical properties of supercritical fluids tend to vary non-linearly near the pseudo-critical region. Traditionally, empirical correlations are used to calculate the heat transfer coefficient. It has been shown in the literature and within our own studies that these correlations provide inaccurate predictions near the pseudo-critical line, where heat transfer may be deteriorated or enhanced, resulting from strong …

Surface-Driven Instabilities At Oil-Water Interfaces, Anelisse Claros Mendieta

Graduate Theses and Dissertations

Fluid-fluid interactions are such a wide area and can be observed in different scenarios such as geothermal systems, waterflooding of reservoirs, oil recovery, and water treatment processes. This thesis aims to deepen the understanding of fluid-fluid interactions which include Marangoni flows, charge related instabilities, and surface activity. This thesis studied the interactions of micrometer-sized droplets of an oil (toluene) with surfactant Di-(2-ethylhexyl) phosphoric acid (DEHPA) in the aqueous phase. One of the main goals is to understand several surface-driven instabilities and how those can be manipulated for future applications.Furthermore, this thesis aims to use these oil-surfactant droplets as a medium …

Understanding Unsteady Corner Separation Within Wing-Body Junction Flows, Paul G. Winner

Doctoral Dissertations and Master's Theses

Wing-body junction flows, formed at the interface between a wing and fuselage surface, are a complex, coupled, three-dimensional, turbulent flow field. This thesis focused on the unsteady corner separation that develops at the trailing edge of this wing-body junction under certain conditions. A NACA 0015 wing mounted on a flat plate at an angle of attack of 13°was used as the model junction flow field. The wing had an aspect ratio of 8 with a linear washout twist of 15°. The Reynolds number based on the wing chord was Re_c = 4.5 × 10⁵. Time-dependent stereoscopic particle …

Studies Of Multiphase Distribution And Flow In Bubble/ Slurry Bubble Columns With /Without Internals And Advanced Sustainable Construction Materials Using Sophisticated Measurement Techniques, Omar Farid

Doctoral Dissertations

"Bubble/slurry bubble columns have been widely studied and employed as multiphase flow reactors with and without vertical heat-exchanging tubes. In order to understand more deeply the effect of the dense internals on the hydrodynamics of bubble/slurry bubble column, systematic experiments were performed to visualize and quantify using the radioactive particle tracking (RPT) technique. A new methodology for implementing the radioactive particle tracking (RPT) technique has been developed to investigate the effect of the dense internals on the hydrodynamics of the bubble/slurry column reactor. Monte Carlo N-Particle (MCNP) simulation has been implemented to simulate the system to generate a large number …

Matlab Model To Predict Liquid Hydrogen Spill Characteristics And Safety, Amy Gravenstein

Williams Honors College, Honors Research Projects

The potential of using liquid hydrogen for propulsion is often undermined due to its perilous nature. Hydrogen has a wide flammability range when mixed with air (4.0 - 75.0% hydrogen) and a low ignition energy (0.019 mJ). Liquid hydrogen adds to this high risk as a cryogenic fluid that is to be maintained below -22 K. A liquid hydrogen model has been created in MATLAB that can model various spill scenarios from cryogenic liquid hydrogen vessels. This model takes into consideration the spill rate, spill temperature, air temperature, duration of spill, and air flow conditions to calculate the mass accumulation, …

Fundamentals Of Microgel Flooding And Nanoparticles-Stabilized Foams In Enhanced Oil Recovery, Shuaijun Li

Dissertations and Theses

For centuries oil has remained a critical energy source for human civilization. After years of extraction, many oil fields have reached or are reaching a decline stage of production, even though up to a half of the total crude oil reserves in these fields has not been recovered yet. One reason is due to the structural heterogeneity of the oil reservoirs—reservoirs may consist of regions of higher permeability with larger pore size and regions of lower permeability with smaller pore size. Displacing fluids tend to flow through large permeability zones only without reaching the oil trapped in low permeability region; …

Droplets In An Electric Field: Surface Rheology, Coalescence And Rebound, Yu Han

Dissertations and Theses

Electrocoalescence is the process in which pairs of conducting droplets suspended in a continuous dielectric (nonconducting) liquid phase are drawn together and merge upon the application of an electric field. The electric field polarizes each of the droplets in the field direction. The polarization causes the drops to deform and drives a dipolar attraction which forces them to approach each other and coalesce. Many technologies use electric fields to manipulate fluid dispersions. Electrocoalescence is an essential unit operation for separating water droplets in a crude oil. This water in oil emulsion is stabilized by surfactants, such as asphaltenes, resins and …

Shear Thickening In Dense Bidisperse Suspensions By Dynamic Simulation, Nelya Malbranche

Dissertations and Theses

Shear thickening, which corresponds to an increase of viscosity with shear rate, is ubiquitously observed in many concentrated suspensions and, as such, has implications for many industrial materials and geological phenomena. Controlling shear thickening is of significant importance, and many studies have been devoted to it. Recent works link shear thickening to the shear-induced transition from a lubricated particle interaction at low shear stress to a predominantly frictional interaction at high stress. In this dissertation, we investigate bidispersity and focus on mechanisms contributing to the viscosity evolution in rate-dependent suspensions, something that has not been addressed before. We perform detailed …

Scale Model Equations And Optimization For Annular Flow Of Non-Newtonian Fluids Between Eccentric And Rotating Cylinders, Wei Zhang, Pooya Khodaparast, Amin Mehrabian Dr., Amir Shojaei

Progress in Scale Modeling, an International Journal

A broad range of engineering applications involves helical flow of non-Newtonian fluids between two eccentric cylinders. These applications often require estimation of the frictional pressure losses along the axes of the cylinders. Laboratory flow loops are commonly used to study the flow characteristics at smaller scales of investigation. This study uses the laws of similarity and dimensional analysis to obtain a set of scaling equations between the laboratory and prototype scales of the described annular flow. These equations are derived for four types of fluid rheology including Newtonian, power-law, Bingham-plastic, and yield power-law.

Results are expressed through a set of …

Uncertainty Of The Ultrasonic Method For Determining The Strength Of Concrete, Ortagoli Sharipovich Hakimov, Zamira Khudoyberdiyevna Ernazarova

Chemical Technology, Control and Management

The issues of measuring the strength of concrete by the method of surface sounding by ultrasound are considered. A measurement model and formulas for estimating the total standard measurement uncertainty, information about the standards used, measurement tools and methods, and environmental parameters are given. Information about the estimation of uncertainty in the form of "eight steps", such as: measurement task; mathematical model of measurement; analysis of input values; observation results; correlations; uncertainty budget; expanded uncertainty; measurement result. It has been established that the uncertainty of type B of the ultrasonic method for determining the strength of concrete is much less …

Mathematical Modeling Of Processes Of Diagnostics Of Technical And Technological Objects, Azizbek Nodirbekovich Yusupbekov, Khurshid Salim Ugli Turayev

Chemical Technology, Control and Management

The work is an introduction to the technical diagnostics of technical (or technological) objects. It discloses the basic concepts and definitions of the reliability of dynamic systems as objects of diagnostic reference knowledge and their diagnosis. Structural schemes of diagnosing objects with individual and combined channels of influence are analyzed. Questions of rational construction of base of reference knowledge are stated.

Developing Advanced Process Control System For Manufacturing Processes Using Virtual Analyzer, Elyor Erkinovich Samadov

Chemical Technology, Control and Management

This research reflects outlines the main potential features of Advanced Process Control (APC) systems for improved control of technological processes and production. It is shown developing APC systems using a virtualized analyzer (VA) is a very effective technique to increase the efficiency of industrial production. This research reflects the main steps of generating VA as part of the APC system and also describes the key features of each step-in terms of analyzer synthesis.

Design Lifecycle Management Of Technological Processes, Yusuf Shodiyevich Avazov

Chemical Technology, Control and Management

The issues of life cycle management of design processes of complex technological processes are considered. An analysis of works devoted to the automated design of technological processes and industries, product life cycle management, and the use of predominant modeling in design is presented. A structure for the implementation of the design of technological processes is proposed and it’s components are described. An algorithm is proposed to reduce the life cycle of the design of a technological process. The sequence of selection of the most optimal project options with the help of the proposed algorithm is described. It is shown that …

Predictive Analysis And Synthesis, Modeling And Control Of Complex Technological Processes And Systems, Zhahongir Sherboyevich Bekqulov

Chemical Technology, Control and Management

Consider the theoretical underpinnings of practically predictive analysis and synthesis, modeling and automatic control of complex chemical technological processes and systems, and the evolution of advanced (or advanced) APC (Advanced Process Control) control of technological processes and industries. The current state of industrial automation systems and the characteristics of their deployment are highlighted. The features of each stage of the analysis and synthesis of APC - advanced process control for complex dynamic objects are disclosed. The real situation and features of the implementation of industrial automation systems of industrial enterprises are reflected.

New Transformer Changer Static Characteristics Measuring Angle Silences Difference, Sultan Faizullayevich Аmirov, Nurulla Raxmatullayevich Yuldashev

Chemical Technology, Control and Management

Presented the specific features of the new transformer converter, which measures the difference in angular displacement, and examines the nonlinearity levels of static characteristics, sensitivity and static characteristics. Studies have shown that in a new measuring device, where one of the two moving parts consists of a magnetic conductor made in the form of an Archimedean spiral made of ferromagnetic material, the balance of the magnetic bridge changes not only depending on the angle of rotation of it’s shoulder resistances. the current is disturbed by the change in the magnitude of the combined air gap depending on the angle of …

Quality Control Of Combustion Of Gaseous Fuel In Furnaces, Azamat Toirovich Rajabov

Chemical Technology, Control and Management

The issues of research and development of systems for monitoring the availability and quality of the process of fuel combustion in industrial furnaces are interpreted. The perspective of using new elements in control systems - communication sensors for the presence and quality in gas-burning installations and furnaces are shown. A method has been developed to control the optimal aeration coefficient based on the extreme of the total integral amplitude-frequency characteristic of the flame conductivity pulsations, which makes it possible to control the quality characteristics of gas-burner devices and control the ratio of the components of the combustible mixture with high …

Algorithm For Calculating The Parameters Of A Multi-Position Electromagnetic Linear Mechatronic Module, Nazarov Khayriddin Nuritdinovich, Matyokubov Nurbek Rustamovich, Temurbek Omonboyevich Rakhimov

Chemical Technology, Control and Management

Currently, in the world in the field of science, engineering and technology, including in mechatronics and robotics, the creation of multi-coordinate mechatronic systems that perform power and control functions is becoming of paramount importance, this is due to a number of important positive qualities of the systems, such as simplicity and compactness of the design, the possibility of obtaining significant efforts, high accuracy and stability of the establishment of fixed positions, ease of control and high reliability. This article presents the calculation of the parameters of multi-position mechatronic modules based on linear execution elements. In the construction of this model, …

Regular Algorithms For Adaptive Identification Of Linear Non-Stationary Systems, H.Z. Igamberdiyev, H.I. Sotvoldiev, U.F Mamirov

Chemical Technology, Control and Management

The article deals with the formation of regular algorithms for adaptive parametric spline identification of linear non-stationary systems. Analyzed the issues of constructing adaptive identification of continuous linear non-stationary systems with monotonic and sign-constant parameters. In this case, in a non-stationary system, the entire observation interval is in some way divided into sub-intervals. Identification is carried out at each of the parameter constancy intervals, while the parameter matrix is re-evaluated for the next interval. The input data of the system are determined with an error depending on the error of approximating the state of the system by splines and approximating …

Water Recovery From Bioreactor Mixed Liquors Using Forward Osmosis With Polyelectrolyte Draw Solutions, Calen Raulerson

All Theses

The objective of this research was to test the feasibility of using forward osmosis (FO) with polyelectrolyte draw solutions to recover water from bioreactor mixed liquors. When combined with an Anaerobic Osmotic Membrane Bioreactor (AnOMBR), such a system could process fecal and food waste from astronauts aboard the International Space Station (ISS) and reclaim important nutrients and water. This project focused on measuring the obtainable water recovery rates from bioreactor effluent, and the identifying challenges associated with the operation.

AnOMBRs feature several advantages over aerobic bioreactors, and non-osmotic anaerobic membrane bioreactors (AnMBR). Anaerobic bioreactors avoid the significant energy costs of …

Towards Long Term Colloid Suspension In A Vertically Rotated System., Md Mahmudur Rahman

Electronic Theses and Dissertations

Within a colloidal suspension gravity may compromise the observation of governing physical interactions, especially those that are weak and/or take significant time to develop. Conducting the experiment in a long-term microgravity environment is a viable option to negate gravitational effects, though significant resources are required to do so. While it may not be possible to simulate long-term microgravity terrestrially, particles can resist quick sedimentation in a confined suspension system rotating vertically with appropriate rotation speed. The goal of the investigation is to demonstrate the existence of long-term particle suspension regime for a certain colloidal suspension while characterizing colloidal behavior due …

Information Software And Devices For Energy Efficiency Management And Control, Narzullo Nuriddinovich Mirzoyev

Chemical Technology, Control and Management

The article provides information on modern methods of management and control of energy efficiency at industrial enterprises. This includes the software needed to manage and monitor energy efficiency, as well as the formation of a database. In addition, a structural diagram of an intelligent power monitoring system has been developed and its elements have been selected. Describes the principle of operation of an intelligent measuring device, its connection to the network, conversion of analog signals to digital, channels and ranges of signal transmission, metrological characteristics. The article details the capabilities and benefits of smart meters.

Analysis Of Water Treatment Methods For Circulating Water Supply In Industrial Plants, Djalolitdin Paxritdinovich Mukhitdinov, Nilufar Abdusomi Kizi Yunusova

Chemical Technology, Control and Management

This scientific paper deals with the problem of extracting Ca2+ and Md2+ salts from water in order to prevent the formation of scale on the heating surfaces of heat exchange equipment. The features, advantages and disadvantages of chemical, membrane and ion exchange methods of water treatment have been evaluated. It has been shown that the chemical method of water purification can be used only for the preparation of industrial water at large stations (at the same time, high residual hardness prevails in the water, the equipment has low productivity), and the membrane method requires pretreatment of water, creation of overpressure …

Ultrasonic Extraction Of Instant Forms Of Plant Substrates In Industrial Production, Shakhnoza Abduvaxitovna Sultanova, Jasur Safarov, Azamat Bakir O'G'Li Usenov, Doston Ishmuhammat Ogli Samandarov, Qobil Akmal Ogli Mukhiddinov

Chemical Technology, Control and Management

In recent years, both in our country and abroad, ultrasonic extraction methods have been increasingly used in industrial production, which is associated with the extraction of various substances and compounds from natural plant substrates. Domestic and foreign experience shows that this method has significant advantages over traditional methods and can significantly increase the efficiency and profitability of industrial enterprises, producing complete and functional food products.

This article discusses a brief theory of ultrasonic cavitation and the experience of extracting substrates from plants. Different results have been compared and analyzed.

Analysis Of Grain Product Drying Methods, Azizbek Nodirbekovich Yusupbekov, Dilmurod Egamberganov

Chemical Technology, Control and Management

Various drying methods and grain characteristics have been studied. The advantages and disadvantages of various grain drying methods were obtained. The use of the following methods of drying grain products is very useful for speeding up the drying process, reducing waste, achieving more flexible process management and delivering all the nutrients of dried grain and grain products to the subsequent production process. The technological approaches that increase the efficiency of high-quality production after drying grain products, the requirements for modern grain dryers have analyzed. The ways of overcoming the problem of high energy consumption in the process of drying grain …

Implementation Of Distance Learning At Universities Using The Experience Of The Honeywell Process Control Laboratory At Tashkent State Technical University, Nodirbek Rustambekovich Yusupbekov, Adilov Tulkunovich Farukh, Isakova Ismailovna Sitora

Chemical Technology, Control and Management

The experience of modernization of the Honeywell Process Control Laboratory at Tashkent State Technical University has been considered (which is equipped with upgraded equipment (simulators for simulating various technological processes, distance learning tools). As a result, the quality of the demonstration of process control mechanisms increased the availability of theoretical and practical knowledge in the field of automated control systems. They also considered the teaching methods necessary for a modern student – remote access in real time, when students pass a knowledge test, consult with teachers, etc.