Chemical Engineering Commons^™

Advanced Nanomaterials And Module Designs For Efficient Photothermal Water Treatment, Deoukchen Ghim

McKelvey School of Engineering Graduate Student Theses & Dissertations

Water scarcity is one of the most serious challenges that human beings face, and the demand for clean water will continuously increase as populations grow. Creating potable water from saline water is an important way to meet global freshwater demands. However, current desalination techniques require high energy consumption and a large scale to be efficient, restricting their utilization in remote and underdeveloped areas. These constraints motivate the development of sustainable water treatment methods that can be used with less energy input, in small modular configurations, and in off-grid water treatment systems. As an abundant and renewable energy source, sunlight has …

Quantifying The Workability Of Calcium Sulfoaluminate Cement Paste Using Time-Dependent Rheology, Sukanta K. Mondal, Adam Welz, Carrie Clinton, Kamal Khayat, Aditya Kumar, Monday Uchenna Okoronkwo

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Poor workability is a common feature of calcium sulfoaluminate (CSA) cement paste. Multiple chemical admixtures, such as set retarders and dispersants, are frequently employed to improve the workability and delay the setting of CSA cement paste. A quantitative assessment of the compatibility, efficiency, and the effects of the admixtures on cement paste workability is critical for the design of an appropriate paste formulation and admixture proportioning. Very limited studies are available on the quantitative rheology-based method for evaluating the workability of calcium sulfoaluminate cement pastes. This study presents a novel and robust time-dependent rheological method for quantifying the workability of …

Wind Tunnel Modeling Of Jack Rabbit Ii Mock Urban Environment Gas Concentration Measurements, Sami S. Fares

Graduate Theses and Dissertations

The 2015 Jack Rabbit (JR) II field trials were conducted to improve understanding of the denser-than-air dispersion of chlorine in an urban environment. The field study involved five large-scale, outdoor release trials of chlorine in a mock urban environment (MUE) at Dugway Proving Ground (DPG). Various instrumentation was deployed, including JazTM Ultraviolet-Visible (UV-Vis) point sensors capable of measuring gas-phase chlorine concentration throughout the mock urban array.

The Chemical Hazards Research Center (CHRC) was tasked by the Chemical Security Analysis Center (CSAC) with the Mock Urban Wind Tunnel (MUWT) program to study the 2015 JR II Trials at wind tunnel scale. …

The Effective Strategies For Mitigation The Impact Of Covid-19 On Construction Projects In Egypt, Nora Magdy Essa, Ibrahim Mahdi, Hassan Mohamed Ibrahim

Future Engineering Journal

From the time when the first narrated infections in Wuhan China, in late 2019, COVID-19 has had a substantial peal on human life and health. By the early of 2020, the World Health Organization (WHO) announced the eruption of COVID-19, a public health crisis of international concern. On 11 March 2020, the World Health Organization officially announced COVID-19 a pandemic. The first case was infected in Egypt of covid-19 on Feb 14, 2020 (Gilbert et al., 2020). On 16 March 2020, the Egyptian Government began issuing decisions as preventative courses as part of the country's inclusive plan to cope with …

Estimating The Weights Of Latticed Power Transmission Towers Using Genetic Programming, Ahmed M. Ebid Dr.

Future Engineering Journal

The recent booming in the power network industry inspired a lot of researchers to develop models to estimate the optimum cost of transmission towers. Unlike previous researches which depended on design the tower from scratch, this research depends on collecting actual database from several projects around the globe and applying the well-known (GP) technique to develop a model to predict the tower weight. The accuracy of the developed formula was about 84%. The developed model could be used in early tender stage or to check design economy.

Evaluation Of Aluminum Dissolution, Current Density, And Pitting Patterns During Electrocoagulation, Monica Castro Carias

USF Tampa Graduate Theses and Dissertations

Electrocoagulation (EC) is a sustainable water treatment process involving the generation of coagulants on-site through the application of a voltage on metal (usually aluminum or iron alloys). The factors that impact EC system performance have been well researched, however further research is needed on the factors that impact anodic dissolution of aluminum electrodes, especially when the technology is transferred to full-scale applications. Electrode fouling is one of the factors that can impact dissolution of the anode during EC due to the formation of a protective oxide/hydroxide layer on the electrode surface. Previous studies have addressed electrode fouling by reversing polarity, …

Understanding The Interfacial Processes Of Reactive Nanobubbles Toward Agricultural Applications, Xiaonan Shi

Dissertations

There is a growing interest in nanobubble (NB) technology because of its diverse applications (e.g., detergent-free cleaning, water aeration, ultra-sound imaging and intracellular drug delivery, and mineral processing). NBs have a higher efficiency of mass transfer compared to bulk scale bubbles due to the high specific surface areas. The high specific surface also facilitates physical adsorption and chemical reactions in the gas liquid interface. Furthermore, the collapse of NBs creates shock waves and the formation of hydroxyl radicals (OH).

However, it remains elusive why or how NBs are stabilized in water and particularly, the states of internal pressures of NBs …

A Circular Economy Approach To Improve E-Waste Recycling In California: Economic Potential And Policy Options, Kripa Shah

Master's Projects and Capstones

The higher consumption rates of electronic devices along with their short life cycles and few repair options poses a huge challenge for E-waste industries to manage them effectively. E-waste comprises of hazardous materials and toxic constituents that can affect the environment and public health through improper disposal. However, they also contain few valuable materials that, if recovered, can reduce the dependence on virgin raw materials. Circular economy has the potential to utilize these valuable materials and gain environment and socio-economic benefits. The research explains how the adoption of a circular economy approach can help improve the E-waste recycling in California …

Probing Myosin Ensemble Mechanics In Actin Filament Bundles Using Optical Tweezers, Omayma Al Azzam, Janie C. Watts, Justin E. Reynolds, Juliana E. Davis, Dana N. Reinemann

Faculty and Student Publications

Myosins are motor proteins that hydrolyze ATP to step along actin filament (AF) tracks and are essential in cellular processes such as motility and muscle contraction. To understand their force-generating mechanisms, myosin II has been investigated both at the single-molecule (SM) level and as teams of motors in vitro using biophysical methods such as optical trapping. These studies showed that myosin force-generating behavior can differ greatly when moving from the single-molecule level in a three-bead arrangement to groups of motors working together on a rigid bead or coverslip surface in a gliding arrangement. However, these assay constructions do not permit …

Fate And Transport Of Toxoplasma Gondii Oocysts In Saturated Porous Media: Effects Of Electrolytes And Natural Organic Matter, Christian Pullano

All Theses

Toxoplasma gondii is a pathogenic microorganism that is currently a threat to public health. Understanding the fate and transport of T. gondii through the soil and groundwater is vital in determining the risk it poses to water resources and human health. The physico-chemical interactions between the groundwater and the bio colloid within an aquifer will dictate its mobility and its ability to infect humans. This research examines how various naturally occurring groundwater chemistries containing organic compounds and monovalent and divalent salt solutions will alter the fate and transport of T. gondii. Solutions containing various concentrations of humic acid, fulvic …

Hydration Of High-Alumina Calcium Aluminate Cements With Carbonate And Sulfate Additives, Jonathan Lapeyre, Sai Akshay Ponduru, Monday Uchenna Okoronkwo, Hongyan Ma, Aditya Kumar

Chemical and Biochemical Engineering Faculty Research & Creative Works

This study investigated the influence of limestone (LS) and calcium sulfate (C$) mineral additives on the hydration kinetics of high-α-Al₂O₃ calcium aluminate cement (CAC) utilizing experimental techniques and thermodynamic simulations. Increasing the replacement level of limestone or calcium sulfate increased the cumulative heat of the hydration reaction. The limestone exhibited limited acceleratory effects to the CAC hydration kinetics due to the coarseness of the powder. The coarse particle size distribution limited any heterogenous nucleation that would have occurred with a finer particle size as well as the intrinsic insolubility kinetically limits the formation of monocarboaluminate phases. Conversely, …

Control Strategy For Solar Energy-Saving Lamps For Optimized Energy Utilization And Sustainability Of Operation Durability: Indonesia Case, Burhanuddin Halimi, Agus Purwadi, Nana Heryana

Makara Journal of Technology

To solve the electrification ratio issue, the Indonesian government has promoted the use of solar energy-saving lamps. This study proposes a control strategy that adopts current reference time-based profiling for solar energy-saving lamps. For optimal energy consumption, the current reference profile is determined according to users’ daily energy requirements. From the aspect of user comfort, a gradual step reference profile is also introduced to provide a subtle change in lighting intensity level. The proposed control strategy can minimize energy consumption and optimize the operation durability of the system. The concept is verified by simulating four scenarios, the results of which …

Mechanical Behavior Of Clay Soil Stabilized With Fly Ash And Bottom Ash, Soewignjo Agus Nugroho, Azra Zulnasari, Ferry Fatnanta, Andius Dasa Putra

Makara Journal of Technology

Soil is one of the most important aspects of an infrastructure given its functions of receiving and holding structural loads. However, not all soils have good physical and mechanical properties. To overcome those conditions, stabilization of the soil is practiced to meet the technical requirements. This study aims to determine the behavior of high plasticity clay stabilized with lime, fly ash, and bottom ash. These additives can be used as a stabilizing agent to increase soil strength. The percentage of additives varied from 5%–25% then mixed with clay and were tested through the (Unconfined Compression Strength (UCS) test. The UCS …

Enhancement Of Biogas Production Through Solid-State Anaerobic Co-Digestion Of Food Waste And Corn Cobs, Lukhi Mulia Shitophyta, Anisa Salsabila, Firanita Angraini Putri, Siti Jamilatun

Makara Journal of Technology

Although biogas has been primarily produced through liquid anaerobic digestion, this method leads to the floating and stratification of fibers and non-homogeneous mixing, which can reduce the biogas yield. Alternatively, biogas can be produced by the solid-state anaerobic digestion (SS-AD) of organic material with a high solid content, such as corn cobs. We investigated the co-digestion of food waste and corn cobs as a biomass feedstock for SS-AD in biogas production. We measured the effects of the total solid (TS) content, percentage of food waste, and reduction in volatile solids (VS), from which we determined its appropriate kinetic model. We …

Feasibility Study Of Implementing Gamma-Ray Computed Tomography On Measuring Aggregate Distribution And Radiation Shielding Properties Of Concrete Samples, Omar Farid, Nima Farzadnia, Kamal Khayat, Muthanna H. Al-Dahhan

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Aggregate segregation is one of the key defects that impair the performance of concrete at fresh and hardened stages. This study aims to assess the feasibility of using an advanced technique to identify/scan/determine the aggregate segregation of concrete elements and determine radiation shielding properties of the concrete. The gamma-ray computed tomography (γ-CT) technique was employed to study aggregate distribution/dispersion in self-consolidating concrete (SCC). Accordingly, two SCC mixtures with moderate segregation (MS) and high segregation (HS) levels were cast and compared with highly stable SCC with no segregation (NS). The γ-CT scans were located on three different levels of concrete specimens …

Development & Validation Of A Piv System For Obtaining Data From A Uasb Reactor, Camila D' Bastiani, Gerald Gallagher, David Kennedy, Anthony Reynolds

Conference Papers

Anaerobic digestion processes can generate energy in the form of biogas while treating organic wastewater. The efficiency of the treatment, and thus the generation of biogas, is closely linked to the type and design of the reactor, and the technology used. Granular anaerobic digestion technology offers advantages such as a higher loading rate and reduction of the space needed. However, the hydrodynamics inside this type of reactor can be complex due to the presence of solids (granules) and gas (biogas) phases along with the liquid phase (wastewater). This is one of the reasons why the study and optimization of reactors …

The Greenest Solar Power? Life Cycle Assessment Of Foam-Based Flexible Floatovoltaics, Koami Soulemane Hayibo, Pierce Mayville, Joshua M. Pearce

Electrical and Computer Engineering Publications

This study presents a life cycle analysis (LCA) of a 10 MW foam-based floatovoltaics (FPV) plant installed on Lake Mead, Nevada, U.S. A material inventory of the flexible crystalline silicon (c-Si)-based module involved massing and determination of material composition of the module's encapsulation layers with ATR/FTR spectroscopy and electron microscopy. The LCA was performed using SimaPro and the results were interpreted in terms of cumulative energy demands, energy payback time, global warming potential, GHG emissions, and water footprint including negative values for reduced evaporation. A sensitivity analysis was performed on the lifetime of the modules and the foam-based racking. The …

Examining The Effect Of A Chitosan Biopolymer On Alkali-Activated Inorganic Material For Aqueous Pb(Ii) And Zn(Ii) Sorption, Sukanta K. Mondal, Chenglin Wu, Felix C. Nwadire, Ali A. Rownaghi, Aditya Kumar, Yusuf Adewuyi, Monday Uchenna Okoronkwo

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Biopolymers and alkali-activated materials have attracted a great deal of attention as adsorbents for the removal of heavy metal contaminants from aqueous solutions. Both materials are sustainable and feature unique properties, but biopolymers are relatively more expensive or difficult to prepare and exhibit low mechanical and surface properties, a narrow pH range, and thermal stability. In this study, hybrid adsorbents were prepared from both types of material, by alkali activation of low-cost fly ash precursors accompanied by incorporation of 0-2%mass chitosan biopolymer. Two types of alkaline activating solutions, NaOH and Na2SiO3, were employed to generate two sets of hybrid adsorbents …

Application Of Artificial Intelligence For Co2 Storage In Saline Aquifer (Smart Proxy For Snap-Shot In Time), Marwan Mohammed Alnuaimi

Graduate Theses, Dissertations, and Problem Reports (ETD)

In recent years, artificial intelligence (AI) and machine learning (ML) technology have grown in popularity. Smart Proxy Models (SPM) are AI/ML based data-driven models which have proven to be quite crucial in petroleum engineering domain with abundant data, or operations in which large surface/ subsurface volume of data is generated. Climate change mitigation is one application of such technology to simulate and monitor CO2 injection into underground formations.

The goal of the SPM developed in this study is to replicate the results (in terms of pressure and saturation outputs) of the numerical reservoir simulation model (CMG) for CO2 injection into …

Highway Stormwater Runoff On-Site Treatment Using Bioslope With New Media Of Biochar Amended Topsoils, Ahmed I. Yunus

College of Graduate Studies: Theses & Dissertations

Georgia Department of Transportation (GDOT) has constructed various treatment facilities on its right-of-way (ROW) to collect and treat highway stormwater runoff, emphasizing total suspended solids (TSS) removal. The permit performance goal set by the Georgia Environmental Protection Division (EPD) is 80% TSS removal. Current stormwater best management practice (BMP) treatment facilities include complex and permanent infrastructures such as bioslope, bioretention basins, sand filters, infiltration trenches, and grass channels. Among these BMPs, bioslope has been becoming more popular due to its applicability for roadway embankments and areas with limited ROW constraints. It removes pollutants effectively by physical filtration and chemical adsorption …

Optimum Geological Storage Depths For Structural H2 Geo-Storage, Stefan Iglauer

Research outputs 2022 to 2026

H₂ geo-storage has been suggested as a key technology with which large quantities of H₂ can be stored and withdrawn again rapidly. One option which is currently explored is H₂ storage in sedimentary geologic formations which are geographically widespread and potentially provide large storage space. The mechanism which keeps the buoyant H₂ in the subsurface is structural trapping where a caprock prevents the H₂ from rising by capillary forces. It is therefore important to assess how much H₂ can be stored via structural trapping under given geo-thermal conditions. This structural trapping capacity is thus …

Predictions Of Produced Water Quality And Recycled Water Optimization For Spatially-Distributed Wells In Point Pleasant Formation, Armel Quentin Mbakop

Graduate Theses, Dissertations, and Problem Reports (ETD)

The treatment of produced water as a fracturing fluid is becoming an increasingly important aspect of water management surrounding the booming of the unconventional oil and gas industry. Two main problems facing the oil and gas industry are the availability of water for well drilling and completion and disposal of the produced water. Unconventional well drilling and completion in the Utica shale requires large amounts of water. The wastewater that results after production—containing high levels of organic and inorganic matter— is usually disposed of through deep well injection. A new approach reuses this produced water as part of subsequent fracturing …

Recent Advancements In Electrochemical Conversion Of Carbon Dioxide, Nandan Nag, Amit Kumar, Sumit Sharma, Sandeep Kumar, Amit K. Thakur

Civil & Environmental Engineering Faculty Publications

Electrochemical reduction of carbon dioxide into eco-friendly and clean products is a promising approach to eradicate pollution. Although carbon dioxide emission is inhibited by the advent of renewable sources of energy, it is present in the atmosphere and needs to be cleaned. The reduction of carbon dioxide from atmospheric gases can be accomplished by its adsorption and subsequent transportation to electrolytic chambers, where it is reduced to hydrocarbons, organic acids or carbonates. This review focuses on developing a three compartment electrochemical cell to reduce carbon dioxide used as a catholyte. Various factors affecting the electrochemical reduction of carbon dioxide and …

Advancements In Pressurized Oxy-Combustion Process: Pollutant Control And Process Development, Piyush Kumar Verma

McKelvey School of Engineering Graduate Student Theses & Dissertations

The emission of carbon dioxide from the power industry is one of the major causes of climate change. However, it is well established that the development of human societies across the globe depends on reliable and dispatchable power, which are generally the source of these emissions. There has been a recent growth in the integration of intermittent sources such as wind and solar which are carbon free. But these intermittent sources have significant temporal changes in power production and thus lack reliability and dispatchablity. This is a complicated problem to solve. However, flexible power plants with carbon capture and storage, …

Hydrogen Underground Storage Efficiency In A Heterogeneous Sandstone Reservoir, Doaa Saleh Mahdi, Emad A. Al-Khdheeawi, Yujie Yuan, Yihuai Zhang, Stefan Iglauer

Research outputs 2014 to 2021

Underground hydrogen storage has been recognized as a key technology for storing enormous amounts of hydrogen, thus aiding in the industrial-scale application of a hydrogen economy. However, underground hydrogen storage is only poorly understood, which leads to high project risk. This research thus examined the effect of caprock availability and hydrogen injection rate on hydrogen recovery factor and hydrogen leakage rate to address some fundamental questions related to underground hydrogen storage. A three dimensional heterogeneous reservoir model was developed, and the impact of caprock and hydrogen injected rate on hydrogen underground storage efficiency were analysed with the model. The results …

Microplastics Fouling And Interaction With Polymeric Membranes: A Review, Mitra Golgoli, Mehdi H. Khiadani, Abdellah Shafieian, Tushar K. Sen, Y. Hartanto, M. L. Johns, Masoumeh Zargar

Research outputs 2014 to 2021

The emergence and accumulation of microplastics (MPs) in various aquatic environments have recently raised significant concerns. Wastewater treatment plants (WWTPs) have been identified as one of the major sources of MPs discharge to the environment, implying a substantial need to improve advanced techniques for more efficient removal of MPs. Polymeric membranes have been proven effective in MPs removal. However, fouling is the main drawback of membrane processes and MPs can foul the membranes due to their small size and specific surface properties. Hence, it is important to investigate the impacts of MPs on membrane fouling to develop efficient membrane-based techniques …

Metasurface Cloaks To Decouple Closely Spaced Printed Dipole Antenna Arrays Fed By A Microstrip-To-Balanced Transmission-Line Transition, Doojin Lee, Alexander B. Yakovlev

Faculty and Student Publications

In this work, we present a numerical study of 1D and 2D closely spaced antenna arrays of microstrip dipole antennas covered by a metasurface in order to properly cloak and decouple the antenna arrays operating at neighboring frequencies. We show that the two strongly coupled arrays fed by a microstrip-to-balanced transmission-line transition are effectively decoupled in 1D and 2D array scenarios by covering the dipole antenna elements with an elliptically shaped metasurface. The metasurface comprises sub-wavelength periodic metallic strips printed on an elliptically shaped dielectric cover around the dipole antennas and integrated with the substrate. We present a practical design …

Shale Softening Based On Pore Network And Laboratory Investigations, Di Zhang

Dissertations

This dissertation consists of two major parts: Firstly, experimental investigation of four major shale softening mechanisms and quantifications of structural parameters. Secondly, numerical simulations of nano-scale flow behaviors using the previous experiments determined parameters based on modified pore network modeling.

Hydraulic fracturing is widely applied to economical gas production from shale reservoirs. Still, the gradual swelling of the clay micro/nano-pores due to retained fluid from hydraulic fracturing causes a gradual reduction of gas production. Four different gas-bearing shale samples are investigated to quantify the expected shale swelling due to hydraulic fracturing. These shale samples are subject to heated deionized (DI) …

Droplet And Particle Dynamics In Aerosol Reactors And Environmental System, Sukrant Dhawan

McKelvey School of Engineering Graduate Student Theses & Dissertations

Aerosol science and engineering is an enabler for continual advances in nanomaterial synthesis. The spray-based techniques have been used extensively for the large-scale production of nanoparticles. Synthesis of particles with a desired the size and morphology is of key importance for exploiting their properties for their use in several emerging technologies. In contrast to useful nanomaterials, the aerosols from industrial flue gas, dust, indoor cooking, pathogens, and wildfire etc. are harmful to human health. It is important to understand how these harmful aerosols travel through the environment and potentially impact the health. It is also very critical to improve the …

Kinetic Modeling Study Of Laminar Burning Velocity Of Gasoline–Ethanol–Methanol Blends At Elevated Temperature And Pressure, Ahmad Syihan Auzani, Cahyo Setyo Wibowo, Riesta Anggarani, Yulianto Sulistyo Nugroho, Bambang Sugiarto

Makara Journal of Technology

Gasoline–ethanol–methanol (GEM) blends have been considered to replace pure gasoline as spark ignition engine fuel. Their physical and chemical properties and performance and emission measurements from real engines have been reported previously. However, a fundamental study that can explain the unique results of GEM compared with those of pure gasoline is lacking. This study aims to compare the laminar burning velocity of GEM blends at different mixtures, equivalence ratios, temperatures, and pressures with that of pure gasoline. A laminar flame propagation model and reaction mechanisms from the literature were were for a numerical simulation. In this study, the chemical components …