Chemical Engineering Commons^™

Surface Area And Electrocatalytic Properties Of Feni Nanoparticles For The Oxygen Evolution Reaction (Oer), James Burrow

Chemical Engineering Undergraduate Honors Theses

Iron-nickel bimetallic electrocatalysts have recently emerged as some of the best candidates for the oxygen evolution reaction (OER) in alkaline electrolyte. Understanding the effects of composition and morphology of iron-nickel nanoparticles is crucial for optimization and enhanced electrocatalyst performance. Both physical surface area and electrochemical surface area (ECSA) are functions of morphology. In this study, four different iron-nickel nanoparticle catalysts were synthesized. The catalysts were varied based on morphology (alloy versus core-shell) and composition (low, medium, and high stabilizer concentration). Brunauer-Emmett-Teller (BET) surface area analysis was conducted on three of the synthesized iron-nickel nanoparticles using a physisorption analyzer while electrochemical …

Degradation Of Orange G Through Persulfate Activated Nanoscale Zerovalent Iron Composites And Boron-Doped Diamond Electrodes, Suzana Ivandic

Chemical Engineering Undergraduate Honors Theses

Properly treated wastewater is necessary for water reuse and to avoid unnecessary impacts on the environment. The poultry industry utilizes large amounts of water for poultry processing. The need for innovative ways to treat organic contaminants in the poultry wastewater industry is especially necessary due to increased poultry consumption. The U.S. Department of Agriculture projected Americans would consume approximately 92 pounds of chicken per person in 2017.¹ Dissolved air flotation (DAF) is currently used in poultry wastewater treatment, but DAF does not remove organic contaminants efficiently per effluent standards. Implementation of processes that degrade contaminants directly would benefit the …

Removal Of Carbamazepine From Drinking Water, Paola Marrero-Rivera, Adam Johnson, Jordan Alex Gadberry, Juan Rodriguez, Thomas Krumpolc, Zach Wiese

Chemical Engineering Undergraduate Honors Theses

Due to the increasing prevalence of prescription medication over the past few decades, pharmaceuticals have accumulated in various water sources. This has become a public health concern because many pharmaceuticals have limited research on the effects of chronic low-level exposure.One pharmaceutical of interest that has been detected in water sources is carbamazepine. Carbamazepine (CBZ) is a common pharmaceutical prescribed for the treatment of seizure disorders, neuropathic pain, and various psychological disorders. It’s mechanism of action is “sodium channel blocking,” which is the impairment of conduction of sodium ions in sodium channels. This, in effect, reduces nervous-system conductivity in key areas …

A Proposed Process And Economic Analysis For A Manufacturing Facility For Nylon 6,6, Perry Doles

Chemical Engineering Undergraduate Honors Theses

The global nylon market is a multi-billion-dollar industry that has been thriving in recent years due to advances in the process technology and its flexibility as a material. Nylon 6,6 is a versatile material with uses in many industries because of its ability manipulated into many forms. It is commonly used in applications that require heat resistance, chemical resistance, and high mechanical strength. It is commonly used in luggage, car parts, carpets, and many other plastic products that require the properties that nylon 6,6 exhibits. The versatility and demand for nylon 6,6 make it an attractive process for many potential …

Effects Of Rotating Magnetic Fields On Pem Fuel Cell Performance, Mao-Liang Wu, En-Ze Wang, Guang-De Pan, Zhong-Jun Liu, Fei Xie

Journal of Electrochemistry

Proton Exchange Membrane (PEM) fuel cell performance may be improved by application of additional magnetic fields. In this work, one square permanent magnet, made of either 16 combination cylinder magnets with homopolarity or 16 combination cylinder magnets with heteropolarity, was exerted on the fuel cell surface to produce additional magnetic field affecting PEM fuel cell performance. The influences of magnetic field status (rotating, static and none) on polarization and power density curves measured in a PEM fuel cell were investigated. The results verified the benefit of magnetic field, proving that the magnetic field distribution could improve the fuel cell output. …

Preparation Of Ni(Dpim)2Cl2 Complex For The Electrocatalytic Reduction Of Co2, Li-Pu Zhang, Dong-Fang Niu, Xin-Sheng Zhang

Journal of Electrochemistry

A new Ni(dpim)₂Cl₂complex using 2-(diphenylphosphino)-1-methylimidazole (dpim) as ligand was prepared and served as a catalyst for the electrochemical reduction of CO₂. The electrochemical redox behavior of Ni(dpim)₂Cl₂ in CH₃CN/TPABF₄ solution under nitrogen atmosphere showed the two-electron irreversible reduction at -0.7 V and one-electron quasi-reversible reduction at -1.3 V. After bubbling CO₂ into the electrolyte, the reduction peak appeared at -1.3 V became irreversible and the peak current increased from 0.48 mA·cm^-2 to 0.55 mA·cm^-2. Moreover, the peak current at -1.3 V could further increase …

Preparation Of Co3O4/Ti Electrocatalytic Membrane Electrode For Catalytic Oxidation Of Benzyl Alcohol, Yu-Mei Zheng, Zhen Yin, Hong Wang, Jian-Xin Li

Journal of Electrochemistry

The cobalt oxide(Co₃O₄) nanoparticles were loaded on microporous Ti membrane to prepare Co₃O₄/Ti electrocatalytic membrane electrode by dip-coating method. The microstructures and electrochemical properties of Co₃O₄/Ti electrocatalytic membrane were investigated. The Co₃O₄/Ti electrocatalytic membrane reactor (ECMR) assembled by using the Co₃O₄/Ti electrocatalytic membrane as an anode was adopted for catalytic oxidation of benzyl alcohol to produce benzaldehyde and benzoic acid.The effects of different operation parameters on benzyl alcohol conversion, and selectivity to benzaldehyde and benzoic acid of ECMR were studied. …

Interaction Between Energy And Electrocatalysis —— A Review On The 1st Young Scientist Forum On Energy Electrocatalysis, Hong Li, Wen-Bin Cai

Journal of Electrochemistry

No abstract provided.

Preparation And Properties Of Manganese Oxide And Polyaniline-Carbon Composite Electrode, Tian-Tian Zhou, Bing Wu, Chao Deng, Ying Gao

Journal of Electrochemistry

The polyaniline-carbon (PAnC) electrode was prepared by the polymerization of aniline monomer and activated carbon in ice water bath, and followed by chemical deposition of manganese dioxide MnO₂-PAnC composite material. The specific capacitance of MnO₂-PAnC reached 459 F•g^-1. The cyclic voltammetric results showed a small deformation in the voltammogram curve obtained with the MnO₂-PAnC electrode at high scan rate, indicating good reversibility and capacitive properties. The AC impedance results revealed that the MnO₂-PAnC electrode displayed the smallest charge transfer resistance and the fastest diffusion
rate of surface ions than other …

Simulation Analysis In Dynamic Performance Of Proton Exchange Membrane Fuel Cell Under Starting Condition, Yan Xiao, Ying-Jie Chang, Wei Zhang, Qiu-Hong Jia

Journal of Electrochemistry

Based on the equivalent circuit model, by considering both the dynamic gas pressure model and the dynamic heat transfer model, a lumped parameter model is developed. The start process of the fuel cell is simulated by using SIMULINK software. The undershoot of the voltage is observed from the simulation results, and the response time of the voltage is basically the same as that of the fuel cell temperature, which indicates that the temperature has great influence on the dynamic performance of the fuel cell. From the perspective of the temperature, the dynamic responses of the thermodynamic potential, the activation overvoltage, …

Electrochemical Oxidation Of P-Chlorophenol On Porous Ti/Bdd Electrode Cooperated With Cathode Dechlorination, Rong-Ling Chen, Wei-Min Huang, Ya-Peng He, Jun Shi, Hai-Bo Lin

Journal of Electrochemistry

The electrochemical oxidation of p-chlorophenol on porous Ti/BDD electrode cooperated with synergistic effect of cathode dechlorination was studied. Electrochemical degradation tests of p-chlorophenol were conducted in single and double compartment electrolytic cells separately, and the results showed that the mineralization happened mainly in the anode region. The product of chloride ions produced from the cathodic reduction of 4-chlorophenol in the single cell migrated to the anode region and further generated active chlorine toward electro-catalytic oxidation. At the same time, the chloride ion produced from the cathode of the double cell was difficult to be migrated to the anode region, which …

Synthesis And Electrochemical Properties Of Li3V2(Bo3)3/C Anode Materials For Lithium-Ion Batteries, You Wang, Yi-Wen Zeng, Xing Zhong, Xing Liu, Quan Tang

Journal of Electrochemistry

The Li₃V₂(BO₃)₃/C (LVB/C) composite materials were successfully synthesized in two steps:Firstly, a stoichiomertric mixture of Li₂C₂O₄, V₂O₅, H₃BO₃, H₂C₂O₄•H₂O and ethanol was thoroughly ball-milled to get the precursors. Secondly, the precursors were post-calcinated to get the ultimate products. The calcination temperatures of 750 ℃, 800 ℃ and 850 ℃ were selected based on TG-DTA analyses. The crystal structures, surface morphologies and carbon contents of the samples calcinated at five conditions, …

Spectro-Electrochemical Platforms For Dynamic Analyses Of Catalytic Cascade Systems, Nalin I. Andersen

Nanoscience and Microsystems ETDs

The development of spectro-electrochemical platforms that facilitate the dynamic analyses of complex catalytic cascade systems was explored in this research. These systems facilitated multiple modalities of catalysts and were used as platforms for monitoring catalytic transformations quasi-in situ. The analytical platforms allowed for the characterization of intermediates and products using surface-enhanced Raman spectroscopy (SERS). The design and fabrication of these devices proved to be reproducible, made of materials that can be manipulated for multiple applications, and incorporate fluid mechanics, electrochemistry, and multimodal catalysis. Microfluidic technology offers capabilities for understanding catalytic cascade systems by providing precise dynamic control of …

Synthesis And Electrochemical Properties Of Nickel-Rich Cathode Material Lini0.6Co0.2Mn0.2O2 With High Initial Coulombic Efficiency, Xiao-Yun Guan, Chao-Yu Hong, Jian-Ping Zhu, Wei-Li Wang, Yi-Xiao Li, Yong Yang

Journal of Electrochemistry

Nickel-rich cathode materials LiNi_0.6Co_0.2Mn_0.2O₂(NCM622)were synthesized by a co-precipitation-solid state sintering method at different temperatures. The structure, morphology and electrochemical performance of the as-prepared materials were investigated by X-ray powder diffraction (XRD) /Rietveld refinement, scanning electron microscope (SEM) and electrochemical experiments. It is found that NCM622 calcined at 800 ℃ showed the lowest degree of cation disorder (~1.97%) with a high initial Coulombic effiency of 92.2% and the capacity retention of 81.4% after 100 cycles.

Preparation And Electrocatalytic Activity Of Nitrogen-Doping Tungsten Carbide Catalyst, Pian-Pian Yang, Li-Zhen Huang, Ying-Ying Li, Mei-Qin Shi, Chun-An Ma

Journal of Electrochemistry

Tungsten carbide (WC) is a promising electrocatalyst, however, its electrocatalytic activity is far inferior to Pt and Pt-group metal. In this work, nitrogen-doping tungsten carbide (WN|WC) catalysts with a nanoplate morphology were prepared via the tungsten nitride (WN) as the precursor and sodium tungstate as the tungsten source. The SEM and TEM results indicated that carbon atoms entered into the WN lattice to form the hexagonal close packed WC phase. In this way, an atomic scale heterostructure involving the closely linked interfaces between WN and WC was created . The XRD data confirmed that the cubic crystal structure of WN …

Nanoporous Carbon-Based Co2 Reduction Catalysts: Exploring The Combined Effects Of Surface Chemistry And Porosity, Wanlu Li

Dissertations, Theses, and Capstone Projects

For the first-time sulfur-doped, nitrogen-doped and sulfur, nitrogen-codoped nanoporous carbons were systematically studied as catalysts for CO₂ electrochemical reduction reaction (CO₂ERR). The Faradaic efficiencies (FE) of CO and CH₄ formation were calculated to evaluate the performance of these carbons. The best catalysts showed the FE of CO and CH₄ formation of 29% and 0.76%, respectively. It was found that the overall performance in CO₂ERR dramatically increased upon the reduction pretreatment of the carbons in N₂-saturated electrolyte before the CO₂ reduction process. The pretreated carbon showed the maximum FE of CO …

Fabrication Of Mnox/Mwcnts-Gc Nanocatalyst For Oxygen Evolution Reaction, Islam M. Al-Akraa Dr., Yaser M. Asal Mr, Amr M. Arafa Eng.

Chemical Engineering

Manganese oxide (MnOx) and multiwalled carbon nanotubes (MWCNTs) are intended to modify the GC electrode for oxygen evolution reaction (OER). Optimization of MnOx loading is carried out and the deposition of 55 cycles was sufficient to obtain the highest activity toward OER. The stability of the catalyst is enhanced by the addition of MWCNTs. As a result, an amount of 22 kWh/Kg of O2 of energy is saved. Several techniques including cyclic voltammetry, linear sweep voltammetry, chronoamperometry, chronopotentiometry, field-emission scanning electron microscopy, and energy dispersive X-ray spectroscopy will be combined to track the catalyst activity and to determine its morphology …

Reaction Kinetics Of Ethane Partial Oxidation To Acetic Acid, Sulaiman Al-Mayman, Moustafa A. Soliman, Abdulrhman S. Al-Awadi, Yousef S. Al-Zeghayer

Chemical Engineering

The partial oxidation of ethane to ethylene and acetic acid on supported MoVNbPd/TiO2 (P25 of Degussa) has been investigated. Pd was added in a nano-metallic form. The catalyst composition was also different from similar studied catalysts. This results in a better selectivity towards acetic acid formation. The reaction was carried out in a tubular reactor at temperature range 225–275 °C, total pressure range 0–200 psig and oxygen percentage in the feed gas of 10–40%. The feed gas contains ethane and oxygen. In this work, we develop a kinetic model for the reaction for the developed catalyst. In this model, we …

Partial Oxidation Of Ethane To Acetic Acid Using A Metallic Pd Promoted Movnb Catalyst Supported On Titania, Sulaiman Al-Mayman, Abdulrhman S. Al-Awadi, Yousef S. Al-Zeghayer, Moustafa A. Soliman

Chemical Engineering

The partial oxidation of ethane to acetic acid on a multi-component Mo16V6.37Nb2.05Pdx oxide catalyst supported on Degussa P25 titania has been investigated. The catalyst was characterized using BET surface area, X ray diffractometer (XRD) and transmission electron microscopy (TEM). The reaction was carried out in a differential reactor in a temperature range of 200-275°C and at a total pressure of 200 psi. The addition of trace amounts of nano-palladium, either as palladium oxides or metallic palladium, enhanced ethane oxidation towards the formation of acetic acid with near-complete depletion of the ethylene intermediate from the reactor effluent. The introduction of nano-Pd …

Assembling Of Niox/Mwcnts-Gc Anodic Nanocatalyst For Water Electrolysis Applications, Islam M. Al-Akraa Dr., Yaser M. Asal Mr, Saher D. Khamis Eng

Chemical Engineering

Glassy carbon (GC) electrode is intended to be modified with nickel oxide (NiOx) and multiwalled carbon nanotubes (MWCNTs) in the anodic reaction of water electrolysis. NiOx deposition time is optimized and a 5 min was enough to attain the maximum activity. A further modification of the catalyst with MWCNTs could greatly enhance its stability during continuous electrolysis. As an outcome, an energy amount of 21.7 kWh/KgO2 is minimized. Several electrochemical and materials characterization setups will be utilized to test the catalyst activity and to know its geometry and structure.

Fabrication Of Cuox-Pd Nanocatalyst Supported On A Glassy Carbon Electrode For Enhanced Formic Acid Electro-Oxidation, Islam M. Al-Akraa Dr., Ahmad M. Mohammad Prof, Mohamed S. El-Deab Prof, Bahgat E. El-Anadouli Prof

Chemical Engineering

Formic acid (FA) electro-oxidation (FAO) was investigated at a binary catalyst composed of palladium nanoparticles (PdNPs) and copper oxide nanowires (CuOxNWs) and assembled onto a glassy carbon (GC) electrode. /e deposition sequence of PdNPs and CuOxNWs was properly adjusted in such a way that could improve the electrocatalytic activity and stability of the electrode toward FAO. Several techniques including cyclic voltammetry, chronoamperometry, field-emission scanning electron microscopy, energy dispersive X-ray spectroscopy, and X-ray diffraction were all combined to report the catalyst’s activity and to evaluate its morphology, composition, and structure. /e highest catalytic activity and stability were obtained at the CuOx/Pd/GC …

Title: Investigation Of Oxidative Reduction Reactions In Carbon-Based Electrocatalysts Presentation, Andrew Mason, Siamak Nejati, Shayan Kaviani

UCARE: Research Products

The expense of commonly used electrocatalysts such as Platinum and Palladium, make many battery technologies and electrochemical reactions cost-prohibitive. A new group of promising low-cost catalysts is doped carbon complexes. These materials need further development to reach the same activity as traditional catalysts. But by examining the Oxidative Reduction Reactions (ORR) of various carbon complexes, desirable characteristics and geometries can be identified and enhanced. For this comparative analysis, a series of Carbon Nanotube (CNT) and Graphene Complexes were tested.

NoX Formation In Light-Hydrocarbon, Premixed Flames, Robert T. Hughes

Theses and Dissertations--Mechanical and Aerospace Engineering

This study explores the reactions and related species of NO_x pollutants in methane flames in order to understand their production and consumption during the combustion process. To do this, several analytical simulations were run to explore the behavior of nitrogen species in the pre-flame, post- flame, and reaction layer regions. The results were then analyzed in order to identify all "steady-state" species in the flame as well as the determine all the unnecessary reactions and species that are not required to meet a defined accuracy. The reductions were then applied and proven to be viable.

Surface And Structural Modification Of Carbon Electrodes For Electroanalysis And Electrochemical Conversion, Yan Zhang

Theses and Dissertations--Chemistry

Electrocatalysis is key to both sensitive electrochemical sensing and efficient electrochemical energy conversion. Despite high catalytic activity, traditional metal catalysts have poor stability, low selectivity, and high cost. Metal-free, carbon-based materials are emerging as alternatives to metal-based catalysts because of their attractive features including natural abundance, environmental friendliness, high electrical conductivity, and large surface area. Altering surface functionalities and heteroatom doping are effective ways to promote catalytic performance of carbon-based catalysts. The first chapter of this dissertation focuses on developing electrode modification methods for electrochemical sensing of biomolecules. After electrochemical pretreatment, glassy carbon demonstrates impressive figures-of-merit in detecting small, redox-active …

The Active Phase Of Gold Catalyst For Propylene Epoxidation, Manchhiben Patel

Summer Community of Scholars Posters (RCEU and HCR Combined Programs)

No abstract provided.

Reaction Kinetics Of The Hydrogenation Of Phenol In A Tubular Reactor, Michael Selzer

Williams Honors College, Honors Research Projects

The reaction kinetic parameters for the hydrogenation of phenol to cyclohexanone are determined for the liquid phase reaction with the palladium catalyst supported on an electrospun PVDF membrane. Runs of the reactor were completed at catalyst loadings of 40, 50, and 60 g/m², and tube diameters of 0.187 in and 0.25 in with a runtime of ten hours. One-dimensional and two-dimensional models of the experimental setup were developed. Fitting data to the one-dimensional model found that the pre-exponential factor was 2.50 x 10⁴, the activation energy was 7.69 kJ/mol, and the order with respect to phenol …

Graphene As A Solid-State Ligand For Palladium Catalyzed Cross-Coupling Reactions, Yuan Yang

Theses and Dissertations

Palladium-catalyzed carbon-carbon cross-coupling reactions have emerged a broadly useful, selective and widely applicable method to synthesize pharmaceutical active ingredients. As currently practiced in the pharmaceutical industry, homogeneous Pd catalysts are typically used in cross-coupling reactions. The rational development of heterogeneous catalysts for cross-coupling reactions is critical for overcoming the major drawbacks of homogeneous catalysis including difficulties in the separation, purification, and quality control process in drug production. In order to apply heterogeneous catalysis to flow reactors that may overcome this limitation, the catalyst must be strongly bound to a support, highly stable with respect to leaching, and highly active. While …

The Role Of Microenvironment Reagent Solubility On Reaction Kinetics Of 4-Nitrophenol Reduction, Michael P. Zeevi, Andrew Harrison, Christina Tang

UROP Posters

The Role of Microenvironment Reagent Solubility on Reaction Kinetics of 4-Nitrophenol Reduction

Michael Zeevi¹ with Andrew Harrison¹ and Christina Tang, PhD¹

¹Department of Chemical and Life Science Engineering, VCU School of Engineering

Introduction: Nanoparticles are of increasing interest due to their high surface area to volume ratio, as well as that they enable fine-tuning of the reaction microenvironment. Through flash nanoprecipitation, core-shell polymer nanoreactors were formed by directed self-assembly. Using the reduction of 4-nitrophenol as a model reduction reaction, we investigated the effect of reagent solubility in the nanoreactor microenvironment’s on nanoreactor kinetics.

Methods: The standard …

Electroactivities Of Pd/Fe3O4-C Catalysts For Electro-Oxidation Of Methanol, Ethanol And Propanol, Tao Zou, Qing-Feng Yi, Yuan-Yuan Zhang, Xiao-Ping Liu, Guo-Rong Xu, Hui-Dong Nie, Xiu-Lin Zhou

Journal of Electrochemistry

Development of palladium (Pd) catalysts with high electroactivity for alcohol oxidation is significant for alcohol fuel cells. In this work, Pd nanoparticles were formed by sodium borohydride (NaBH₄) reduction method and subsequently deposited on the surface of carbon supported ferriferrous oxide (Fe₃O₄/C) composites to obtain the Pd/Fe₃O₄-C catalysts with different Fe₃O₄ loadings. Their transmission electron microscopic (TEM) images show that the Pd nanoparticles were uniformly dispersed on the Fe₃O₄/C. Electroactivities of the prepared Pd/Fe₃O₄-C catalysts toward oxidations of C1-C3 …

Cobalt-Based Nitrogen-Doped Carbon Non-Noble Metal Catalysts For Oxygen Reduction Reaction, Meng-Xiu Jiang, Jing Zhang, Yue-Hua Li, Rong Zhang

Journal of Electrochemistry

Transition metal-nitrogen co-doped carbon catalysts have attracted significant attention because of their reasonable activity and remarkable selectivity toward oxygen reduction reaction (ORR) as cathodic reaction in fuel cells. However, the role of transition metal in the active sites of the catalysts still is uncertain. In this work, the Co_x-N_y/C-T catalysts were prepared with BP2000 as a carbon source, urea (Ur) as a nitrogen source and Co(OAc)₂•4H₂O as a metal precursor by a simple chemical method. Meanwhile, in order to optimize the ORR activity, the catalysts were synthesized with different amounts of Co …