Bioresource and Agricultural Engineering Commons^™

Cfx Analysis Of The Heat And Mass Transfer During The Chilling Of A Lamb Carcass Using A 3d Model, Joseph Hannon, Garrett Keane, Micheal O'Flaherty

Presentations

Lamb meat is a popular red meat which must go through a complex refrigeration process before being served at the dinner table to reduce bacterial growth and retain meat quality. A major disadvantage of chilling is the drip losses which are losses in weight by evaporation of water contained within the meat. The aim of this work is to simulate the conventional chilling process of a lamb carcass using a three dimensional model.

Comparison Of Finite Difference And Finite Element (Telemac) Models Of Dublin Bay, Garrett Keane, Zeinab Bedri, John O'Sullivan

Presentations

A number of hydrodynamic and solute mathematical models of Dublin Bay have been developed in the Centre for Water Resources Research in University College Dublin. One of these was an Eulerian-Langrangian finite difference Extended Dublin Bay model named SW2D which was developed by Hussey (1996). It was used in various studies such as the Dublin Bay Water Quality Management Plan and the Howth Outfall Study to predict the effect of the proposed upgrades at the sewage treatment plants on the water quality in these areas. The finite element TELEMAC modelling system developed by the French EDF group was used in …

Immobilization Of Lead In Contaminated Firing Range Soil Using Biochar, Deok Hyun Moon, Jae-Woo Park, Yoon-Young Chang, Yong Sik Ok, Sang Soo Lee, Mahtab Ahmad, Agamemnon Koutsospyros, Jeong Hun Park, Kitae Baek

Civil Engineering Faculty Publications

Soybean stover-derived biochar was used to immobilize lead (Pb) in military firing range soil at a mass application rate of 0 to 20 wt.% and a curing period of 7 days. The toxicity characteristic leaching procedure (TCLP) was performed to evaluate the effectiveness of the treatment. The mechanism responsible for Pb immobilization in military firing range soil was evaluated by scanning electron microscopy-energy dispersive x-ray spectroscopy (SEM-EDX) and x-ray absorption fine structure (XAFS) spectroscopy analyses. The treatment results showed that TCLP Pb leachability decreased with increasing biochar content. A reduction of over 90 % in Pb leachability was achieved upon …

Design And Construction Of A Portable Gantry Hoist, Sam Hutcheson

BioResource and Agricultural Engineering

This report covers the design of a portable gantry hoist with a custom frame design. The design was based off of the materials that were available and practical for this project to save money. The portable gantry hoist will be rated for a 2 ton capacity. The casters, trolley, and hoist were the only parts purchased.

Development And Testing Of An Impact Plate Yield Monitor For Peanuts, Jacob Fravel

All Theses

Advancements in precision agriculture technologies such as yield monitors have allowed for improved management capabilities and reduced input costs for a number of crops. Most commercialized developments in yield monitoring systems and technologies to date have been directed for use with the major grain crops such as corn, soybeans and cereal grains. This research focuses on development and testing of an impact plate yield monitor system for the peanut harvest. Using a four row peanut combine in virginia type peanuts, 4.8 ha (12 ac) of simultaneous yield data were recorded from an Ag Leader® grain (impact plate) yield monitor and …

Heat Of Combustion Of Algae For Use In A Diesel Engine, Cassia Diane Davis

Masters Theses and Doctoral Dissertations

With nearly a quarter of the world’s population living without any access to electricity or modern energy, strategies for providing energy are very important. While the use of fossil fuels can bring the much needed energy to these areas they come with a host of problems. Fossil fuel use contributes to greenhouse gas emissions, air pollution and ocean acidification. In many areas fossil fuels have to be transported in. The subsequent transmission and distribution can be difficult especially in rural areas. Dependence on fossil fuels also leaves the user vulnerable to disruption in deliveries and price fluctuations. While there are …

Thermodynamic Efficiency Evaluation For Distillation Of Ethanol, Joe A. Cavaletto

BioResource and Agricultural Engineering

Energy will always be a consideration when distilling any product. Fog’s End Distillery in Gonzales, CA is a small scale micro distillery for ethanol. For Fog’s End, efficiency is key to staying competitive. In this project the efficiency of energy in vs product out will be calculated. While collecting this data the price/bottle for energy will be determined and used for an assembly cost. To determine the efficiency the fuel usage will be recorded for several distillation trials. The mash contents and product contents will all be measured and calculations will be performed to find the theoretical amount of energy …

Improvements In The Process Of Biohydrogen Production By Thermotoga Neapolitana, Louis Hill

All Theses

The production of biological hydrogen is an important process for the future of sustainability and alternative energies. Thermotoga neapolitana is a hyperthermophilic bacterium that produces H ₂ , CO₂ and acetate via fermentation. The goal of the research was to investigate the sustainable production of H₂ gas using waste agricultural feedstocks, recycled water and a simplified N₂ sparging method technique. A limited sparging method was developed which includes 1 minute of N₂ gas sparging of the reactor headspace and 90 minutes of idle reaction time for cysteine-HCl to react with dissolved oxygen prior to inoculation. This …

Elementary Implantable Force Sensor For Smart Orthopaedic Implants, Rebecca A. Wachs, David Ellstein, John Drazan, Colleen P. Healey, Richard L. Uhl, Kenneth A. Connor, Eric H. Ledet

Department of Agricultural and Biological Systems Engineering: Faculty Publications

Implementing implantable sensors which are robust enough to maintain long term functionality inside the body remains a significant challenge. The ideal implantable sensing system is one which is simple and robust; free from batteries, telemetry, and complex electronics. We have developed an elementary implantable sensor for orthopaedic smart implants. The sensor requires no telemetry and no batteries to communicate wirelessly. It has no on-board signal conditioning electronics. The sensor itself has no electrical connections and thus does not require a hermetic package. The sensor is an elementary L-C resonator which can function as a simple force transducer by using a …

Improving Data Quality For A Dairy Pollutant Emissions Study, Ian K. Hahus, Albert J. Heber

The Summer Undergraduate Research Fellowship (SURF) Symposium

The National Air Emissions Monitoring Study (NAEMS) was sanctioned by the EPA to determine the characteristics of airborne pollutant emissions from confined broiler, egg, pork, and dairy housing. Fifteen representative monitoring sites were selected around the U.S., at which influent and effluent pollutant concentrations were measured in conjunction with airflow and climatic data. Due to the monumental nature of this study and the potential ramifications of its findings, it is of vital importance that the data collected by the researchers and utilized by the EPA be as complete and accurate as possible. To improve the validity of the data collected …

Detection Of Foodborne Pathogens By Micro-Filtration Using A Continuous Cell Concentrator Device, Klaire E. Jeffries, Eduardo Ximenes, Michael R. Ladisch

The Summer Undergraduate Research Fellowship (SURF) Symposium

Protecting consumers from foodborne illness is an important health concern facing the food industry today. An important deficiency exposed by foodborne illness is the inability to track contaminated food back to the source in a timely manner. Although there are established methods that detect bacterial pathogen contamination, they are limited in distinguishing viable bacteria reliably and quickly. Currently, food pathogen testing requires lengthy culture steps, which many times are delayed even longer due to the lack of in-house testing labs. Typically, two to three days elapses between when the food is sampled and the test results are available. This study …

Computer Simulation Study Of Slipper Lubrication In Hydraulic Machines, Jordyn B. Miller, Monika Ivantysynova

The Summer Undergraduate Research Fellowship (SURF) Symposium

Hydraulic pumps and motors are vital components used in many applications today. Specifically, the axial piston pump is important because it is reliable, relatively compact, and has a high horsepower-to-weight ratio. These features make this type of pump very advantageous in hydraulic systems. Maintaining proper lubrication between surfaces in an axial pump, such as the slipper and swashplate, is imperative in order to have smooth operation of the system and prevent metal-to-metal contact. The aim of this research is to find the optimal slipper design and fluid film thickness to simultaneously maintain a balanced pressure and decrease power loss in …

Driftwatch Pollinator Mapping Application, Shreyas G. Sundararaman, Larry Theller, Bernard Engel

The Summer Undergraduate Research Fellowship (SURF) Symposium

Over 65% percent of food consumed in the United States is pollinated by bees. Unfortunately, due to poor farming practices, pesticides are sprayed in bee sensitive areas unknowingly and as a result, the bee population is dwindling at an alarming rate. With lesser bees to pollinate crops, produce is compromised on a very large scale and this could have disastrous impacts on the nation's needs for food. Apiarists and beehive owners face the major responsibility of ensuring that their hives aren't affected by dangerous insecticides and pesticides from the farming areas that they might visit during their crop pollination cycles …

Design Of A Novel Actuation System For Variable Displacement Gear Machine, Mark W. Mahuren, Andrea Vacca

The Summer Undergraduate Research Fellowship (SURF) Symposium

External spur gear pumps are exceedingly useful components in common hydraulic systems. The main issue with external gear pumps is that all current models are limited to only fixed-displacement. This means that for every revolution of the gears inside the pump, a set amount of fluid will always be displaced. Consequently, external gear pumps are limited in their use because they can only operate at full throttle causing inefficiencies when reduced displacement is needed. The successful procurement of a variable displacement gear pump will allow a more efficient use of hydraulic systems, such as in the displacement controlled systems used …

Crane Shaking Platform Design, Bixing Yan, Andrea Vacca

The Summer Undergraduate Research Fellowship (SURF) Symposium

Most of the control methodology of Mobile hydraulic crane is not as energy efficient as people think or want, and the desire to innovate novel, energy-efficient control strategy is the target of most hydraulic experts. To develop or test the control method under real road and off-road conditions, a platform that could simulate the movement and vibration of the crane truck is desired. To design and build the multi-operation platform, a design process includes brain storming, design selection, FEA (Fundamental Element Analysis), mechanical sizing, hydraulic sizing and Bill of Material is required and preferred. After going through all the steps …

Optimization Of Oil Extraction Of Soy Flour Using Mini Extrusion Technology, Alisha Chess, Martin Okos

The Summer Undergraduate Research Fellowship (SURF) Symposium

Mini extrusion technology is a relatively new technology that offers fast timing and processing of food products. This technology paired with the advantageous properties and growing demand for soybeans can lead to a larger span of uses for the extruder that have not yet been explored, including NASA space missions and incorporation of soybeans into developing countries. During past research on parameters of operation, it was discovered that a significant amount of oil was being separated from the soy meal at the die of the mini extruder. Maximum removal of this oil allows use of the soy meal and soy …

Estimation Of Two-Stage Ditch Excavation Volume Using Lidar Data Full Paper, Kirsten E. Paff, Jane Frankenberger, Naime Celik

The Summer Undergraduate Research Fellowship (SURF) Symposium

Drainage ditches are a major pathway for sediment, nutrients, and pesticides to enter stream systems, which threaten environmental and human health. Unlike trapezoidal ditches, two-stage ditches have a vegetated bench that acts as a floodplain, which helps to prevent erosion and to increase the processing of nutrients to improve water quality. Converting a trapezoidal ditch to a two-stage ditch is expensive, due to the large volumes of soil that need to be excavated. Since ditch geometries vary significantly and surveying each potential site by hand would be time consuming and expensive, a tool based upon online Light Detection and Ranging …

Grass Referenced Based Vegetation Coefficients For Estimating Evapostranspiration For A Variery Of Natural Vegetation, Daniel J. Howes, Mariana Pasquet

BioResource and Agricultural Engineering

In arid and semi-arid regions, evapotranspiration from vegetation results in the significant utilization of available water. Accurate estimates of evapotranspiration are required for surface and subsurface hydrologic evaluations as well as irrigation district water balance studies. A significant amount of transferable information exists for irrigated agricultural crops through past and current research in the form of grass or alfalfa reference based crop coefficients (Kc) and basal crop coefficients (Kcb). However, transferable evapotranspiration information on natural vegetation is limited. Much of the work was conducted in the early to mid-1900’s and is presented as actual evapotranspiration from the vegetation at the …

Adaptive Targeting: Engaging Farmers To Assess Perceptions And Improve Watershed Modeling, Optimization, And Adoption Of Agricultural Conservation Practices, Margaret Mccahon Kalcic

Open Access Dissertations

Targeting agricultural conservation practices to farmland that has the greatest impact on surface water quality has received wide support from scientists and watershed managers. The targeting approach has, however, been politically contentious as many believe farmers will oppose the approach on grounds such as privacy invasion and unfair distribution of government incentives. Targeting conservation practices using complex optimization models has become common in the scientific community, and yet targeted results are underutilized in practice because of difficulties such as knowledge transfer and absence of a political framework for their use. For targeting to be successful, it must be politically supported …

Yield And Crop Water Use Efficiency Response Of Drought-Tolerant And Conventional Maize Hybrids Under Different Irrigation Regimes, Plant Populations And Climate Gradients, Ali T. Mohammed

Department of Agricultural and Biological Systems Engineering: Dissertations, Theses, and Student Research

Water scarcity in many regions of the world, including Nebraska, is imposing increasing pressure on water demands in agriculture to meet future food and fiber demand of rapidly growing world populations. One of the viable alternatives to counter this challenge is cultivating new drought-tolerant hybrids/varieties/cultivars. Recently, new drought-tolerant maize (Zea mays L.) hybrids have been developed by major seed companies. However, it is essential to evaluate the performance of these hybrids, in terms of grain yield and crop water use (actual evapotranspiration) in various climatic and soil conditions under large production settings. Research was conducted at four locations across the …

Using X-Ray Imaging Techniques To Determine Density Of Foods, Shivangi Mohan Kelkar

Open Access Dissertations

Density depends on the experimental technique and structural properties of food. True, apparent and bulk are different types of densities. For porous foods such as baked food products and complex food systems, accurate measurement of density is challenging. Empirical correlations dependent on composition and temperature exist to calculate true density. Thus if composition and apparent density are known, porosity can be calculated, porosity = [1 - (apparent density/ true density)]. Various non-destructive diagnostic tools have been employed to study food microstructure. Among these, computed tomography (CT) and digital radiography (DR) utilizing x-ray imaging showed greater capability for evaluation of food …

Ozonation Systems As A Non-Chemical Alternative For Stored Grain Protection, Carlos A. Campabadal

Open Access Dissertations

The use of ozone as a non-chemical alternative in stored grain protection was studied by conducting scale-up demonstrations using a fixed bed ozonation system and developing a semi-continuous counterflow and a continuous flow ozonation treatment system. The objectives of this research were to determine the efficacy of ozonation to control insect pests without affecting end-use quality; to prove the concept of the semi-continuous counterflow ozonation system to ozonate grain at a faster rate and quantify its effect on mold growth reduction; to evaluate the efficacy of a modified screw conveyor for pest control by treating grain in a continuous-flow ozonation …

Advanced Control Strategies For Mobile Hydraulic Applications, Davide Cristofori

Open Access Dissertations

Mobile hydraulic machines are affected by numerous undesired dynamics, mainly discontinuous motion and vibrations. Over the years, many methods have been developed to limit the extent of those undesired dynamics and improve controllability and safety of operation of the machine. However, in most of the cases, today's methods do not significantly differ from those developed in a time when electronic controllers were slower and less reliable than they are today.

This dissertation addresses this aspect and presents a unique control method designed to be applicable to all mobile hydraulic machines controlled by proportional directional valves. In particular, the proposed control …

Direct And Indirect Greenhouse Gas Emissions From Biomass Storage: Implications For Life Cycle Assessment Of Biofuels, Isaac Robert Emery

Open Access Dissertations

Ethanol and other biofuels from cellulosic feedstocks are currently the most promising candidates to replace a large fraction of gasoline consumption in the United States and reduce greenhouse gas emissions. Gaps in current approaches to estimating the net greenhouse gas emissions from second-generation biofuels may lead to underestimation of the carbon intensity of these fuels. Current life cycle assessment models of biofuels do not sufficiently account for biomass losses and emissions associated with the harvest and storage of biomass feedstocks, which can require additional fuel and materials use on the farm as well as reducing the effective yield of a …

Enzymatic Hydrolysis Of Biomass At High-Solids Loadings – A Review, Alicia A. Modenbach, Sue E. Nokes

Biosystems and Agricultural Engineering Faculty Publications

Enzymatic hydrolysis is the unit operation in the lignocellulose conversion process that utilizes enzymes to depolymerize lignocellulosic biomass. The saccharide components released are the feedstock for fermentation. When performed at high-solids loadings (≥ 15% solids, w/w), enzymatic hydrolysis potentially offers many advantages over conversions performed at low- or moderate-solids loadings, including increased sugar and ethanol concentrations and decreased capital and operating costs.

The goal of this review is to provide a consolidated source of information on studies using high-solids loadings in enzymatic hydrolysis. Included in this review is a brief discussion of the limitations, such as a lack of available …

Low-Pressure Testing: Microirrigation Emitters, Charles M. Burt, Kyle Feist

BioResource and Agricultural Engineering

ITRC tested 28 different pressure-compensating (PC) models of microirrigation emitting devices from a total of nine manufacturers in order to compare independent laboratory testing with manufacturer specifications. It is the intention of this report to investigate the ability of currently marketed products to operate in a truly low pressure irrigation system where energy inputs, in the form of pump discharge requirements, can be minimized.

Low-Pressure Testing: Pressure Regulating Valves, Charles M. Burt, Kyle Feist

BioResource and Agricultural Engineering

ITRC tested performance characteristics of pressure regulating valves from a variety of manufacturers. The purpose of the testing was to evaluate the ability of different models of valves to regulate the pressure in a low-pressure system. The testing concentrated on three specific valve performance characteristics: minimal variance from the target downstream pressure caused by changes in flow rate or inlet pressure; minimal hysteresis in outlet pressures; minimal pressure loss (at low inlet pressures) across the valve.

Evaluation Of Broiler Litter Heat Production During Windrowing & Nitrogen Based Gas Emission Mitigation Using Biofilter, Min Lei

Graduate Theses and Dissertations

Ammonia emission from animal feeding operations (AFOs) has negative effects on environment and animals' health. Thus measuring and mitigating ammonia emission from AFOs is important for environmental protection. In chapter I, different ammonia measurements were discussed and a mitigation technology- biofilter was represented.

In-house windrowing of built-up litter has been used by broiler producers to reduce pathogen loads and rejuvenate litter for the next flock. When litter is piled up for an extended period during downtime, heat generated by the litter pile can become a substantial heat source due to the metabolism of microorganisms. In chapter II, heat production rates …

Characterization And Quantification Of Monomers, Oligomers, And By-Products From Switchgrass Hemicelluloses During Biomass Pretreatment, Kris Allan Bunnell

Graduate Theses and Dissertations

Production of fuels and chemicals from biomass is contingent upon economical release of carbohydrates from biomass. Carbohydrates can then be used for production of bio-based products using a biochemical conversion process. Pretreatment, the first step of the biochemical conversion process, has been suggested to be the most costly step of the conversion process. Thus, better understanding the behavior of biomass during pretreatment is imperative for an economically viable production of biofuels and chemicals. Elucidating the physicochemical properties of biomass and developing an understanding the depolymerization patterns of biomass during pretreatment will help progress towards this goal.

In this study, July- …

Juxtaposing Nasa’S Aeronet Aod With Carb Pm Data Over The San Joaquin Valley To Facilitate Multi-Angle Imaging Spectroradiometer (Misr) Pm Pollution Research, John Kanemoto

STAR Program Research Presentations

Airborne particulate matter (PM) has been shown to increase the risk for asthma, chronic bronchitis, cardiopulmonary complications, and respiratory cell membrane damage/infection/leakage. PM levels are currently analyzed from two perspectives: stationary land-based monitoring (LBM) sites and total Aerosol Optical Depth (AOD) atmospheric column measurements. Both perspectives often leave miles of space between measuring locations and will have a continually increasing cost from introducing/maintaining sites. The Multi-angle Imaging SpectroRadiometer (MISR) satellite team hopes to begin investigating/archiving PM levels comprehensively via inputting MISR AOD measurements into a function/model which predicts the amount of ground level PM.

In the future, multivariable spatial correlations …