Bioresource and Agricultural Engineering Commons^™

Irrigation District Turnouts, Charles M. Burt

BioResource and Agricultural Engineering

This is meant to be a very quick, roughly written primer on irrigation district turnout selection. It by no means covers all of the details, but it might help out. ITRC offers flow measurement classes, with online registration at www.itrc.org. We have also done testing on quite a few designs over the years, but the work was almost all confidential in nature.

Modernización De Proyectos De Riego, Charles M. Burt

BioResource and Agricultural Engineering

Un diseño moderno es el resultado de un proceso de reflexión, el cual selecciona la configuración y componentes físicas considerando un programa de operación bien definido y realista basado en el concepto de servicio.

Medición De Gasto En Canales De Riego Y...Otras Cosas, Charles M. Burt

BioResource and Agricultural Engineering

Nuestra opción preferida para Eiqupos de “flujo crítico ” (vertedor or aforador) son Aforadores Replogle (Garganta Larga)

Subcritical Contraction For Improved Open-Channel Flow Measurement Accuracy With An Upward-Looking Advm, Daniel Howes, Charles M. Burt, Brett F. Sanders

BioResource and Agricultural Engineering

Acoustic Doppler velocity meters (ADVMs) provide an alternative to more traditional flow measurement devices and procedures such as flumes, weirs, and stage rating for irrigation and drainage canals. However, the requirements for correct calibration are extensive and complex. A three-dimensional computational fluid dynamics (CFD) model was used to design a subcritical rapidly varied flow contraction that provides a consistent linear relationship between the upward-looking ADVM sample velocity and the cross-sectional average velocity in order to improve ADVM accuracy without the need for in situ calibration. CFD simulations validated the subcritical contraction in a rectangular and trapezoidal cross section by showing …

Commercial Sand Media Filter Tank Criteria For Energy Efficiency - Agricultural Drip Irrigation, Charles M. Burt

BioResource and Agricultural Engineering

Sand media filters are commonly used in agricultural drip irrigation systems. They have the advantages of simplicity and large capacities, and are favored by many farmers and designers over other filtration hardware. The primary justification for the research described in this report was to determine if it is possible and reasonable to use lower-than-accepted backflush pressures and thereby reduce the total pressure requirement for drip systems.

Strawberries: Effects Of Modifying Irrigation Methods For Transplant Establishment 2009-2010, Stuart Styles

BioResource and Agricultural Engineering

The purpose of the project is to develop an analysis of the current irrigation practices of the strawberry growers on the Central Coast of California. The primary research evaluation is during the establishment of transplants where sprinklers are used even though drip irrigation is available. This project has targeted the impacts of salinity on the young strawberry transplants.

The specific objectives of the project are to: (1) Set up a research areas and control plots on a demonstration scale, (2) determine the key factors that affect the problems in early growth of transplanted strawberries, (3) determine relationships between the use …

Practical Experience With State-Of-The-Art Technologies In Scada Systems, Beau Freeman, Charles M. Burt

BioResource and Agricultural Engineering

A Supervisory Control and Data Acquisition (SCADA) system is a powerful tool which, when implemented properly in irrigation districts, can lead to improved water delivery service to farms, more effective operations, reduced spill (and therefore reduced diversions), and in some cases a reduction in costs (less labor, less energy, etc.). However, widespread adoption of SCADA and automation technologies remains a technical and financial challenge for most irrigation districts. In spite of many good hardware and software products available on the market now, putting all the pieces together requires specialized expertise. Nevertheless, by following some straightforward strategies and rules of good …

Pump Operation With Vfd Controlled Motors, Charles M. Burt

BioResource and Agricultural Engineering

There are numerous reasons to consider using a VFD (variable frequency drive) controller with pumps in irrigation and drainage.These include: 1

1. Proper matching of the pump characteristics with the system. Reasonable engineers and salespersons will almost always overdesign pumps. It is very simple – if the pump is too small, there will be complaints. If, on the other hand, the pump delivers a bit more pressure than needed, there is rarely a complaint. Reasons to overdesign include:

Where Is All That Water Going?, Charles M. Burt

BioResource and Agricultural Engineering

Some have proposed to conserve 4-6 Million AF/yr in Agriculture with pragmatic, economical measures. All we need to do is find the inefficiencies. Then we'll get rid of them.

Design, Construction And Evaluation Of A Fueltank/Tool Box Combination, Michael R. Chase Jr

BioResource and Agricultural Engineering

This project is the design and development of a combination tool box and auxiliary fuel tank built as a single unit, specifically built for a 2000 Ford F250 short bed truck; having a fuel capacity exceeding 50 gallons; meeting federal requirements for motor vehicle fuel tanks; performing as an auxiliary tank using the factory fuel gauge and having a tool box that can carry a wide array of tools. This paper will describe the design considerations, the regulation requirements, the material selection, and the construction process of the combination tool box/fuel tank.

Water Conservation's Role In California Water Transfers, Charles M. Burt

BioResource and Agricultural Engineering

This paper describes various irrigation district water transfer projects. Water transfers have been of many types, including agriculture to agriculture, agriculture to urban, and agriculture to environment. In each case that will be described, the unique circumstances of each district will be described. Typical actions include developing a water balance to determine if “wet water” truly exists for conservation, then identifying the sources of that wet water. Subsequent actions include developing designs that will conserve the water, achieving board approval, and constructing and implementing the conservation measures.

Increasing Productivity In Irrigated Agriculture: Agronomic Constraints And Hydrological Realities, Chris Perry, Pasquale Steduto, Richard C. Allen, Charles M. Burt

BioResource and Agricultural Engineering

Irrigation is widely criticised as a profligate and wasteful user of water, especially in watershort areas. Improvements to irrigation management are proposed as a way of increasing agricultural production and reducing the demand for water. The terminology for this debate is often flawed, failing to clarify the actual disposition of water used in irrigation into evaporation, transpiration, and return flows that may, depending on local conditions, be recoverable. Once the various flows are properly identified, the existing literature suggests that the scope for saving consumptive use of water through advanced irrigation technologies is often limited. Further, the interactions between evaporation …

Variability Within Irrigated Fields, Charles M. Burt, Byron Clark

BioResource and Agricultural Engineering

In agricultural production and research, it is common to represent fields as uniform areas. For example, fertilizers, soil amendments, and other inputs have traditionally been applied uniformly (or as uniformly as possible) based on estimated needs for the field as a whole (or as an “average”).

Of course, it is also recognized that fields are not truly uniform with respect to soil characteristics, uniformity of applied water, pest pressures, fertility needs, crop growth and yield, and other characteristics. With the emergence and refinement of variable rate application technology, many growers now attempt to maximize returns by “prescribing” variable amounts of …

Evaluation Of Magnetic Meters For Irrigation Pipeline Measurement, Stuart Styles, Bryan Busch

BioResource and Agricultural Engineering

Magnetic flow meters are used to measure the flow rate of a liquid in a closed pipeline. This type of meter is becoming increasingly popular for measurement with agriculture applications. Electromagnetic meters were tested by the Irrigation Training and Research Center in pipelines located less than the 10 diameters upstream of disturbances with good results. Results show that location guidelines for placing a magnetic meter can be decreased even for turbulent conditions. This paper will discuss how a magnetic flow meter works, advantages and disadvantages of this type of meter, test results, and new guidelines for field applications.

Canal Seepage Reduction By Soil Compaction, Charles M. Burt, Marcus Gardenas, Mohamed Grissa

BioResource and Agricultural Engineering

Large-scale tests were conducted of in-place compaction of irrigation district earthen canal bottoms and sides. Five canal pools with sandy loam soils were compacted. Seepage reduction of about 86% was obtained when the sides and bottoms were compacted; reductions of 12 – 31% were obtained when only sides were compacted.

Improving Pump Performance, Charles M. Burt, Frankline Gaudi, Daniel J. Howes

BioResource and Agricultural Engineering

Options can be specified to minimize power consumption by vertical pumps – both when new and over the life of the pump. Options discussed include bowl coatings, proper well development, improved suction screens, using closed impeller designs, increasing column size, using new bearings, providing proper bearing lubrication, impeller balancing, and polishing impellers. The proper TDH and flow rate must be specified, and the advantages of VFD controls are covered.

Agricultural Water Conservation And Efficiency In California - A Commentary, Charles M. Burt, Peter Canessa, Lawrence J. Schwankl, David F. Zoldoske

BioResource and Agricultural Engineering

This is a Commentary on some of the key points that are presented in “More with Less: Agricultural Water Conservation and Efficiency in California” by Cooley, ChristianSmith, and Gleick of the Pacific Institute, September 2008 (referred to as the “PacInst Paper” in the remainder of this discussion).

The authors of this Commentary have over 120 years combined of experience in agricultural and landscape irrigation. They have worked world-wide in design and installation of all types of irrigation systems (including automated drip systems from 1975 on), design and implementation of irrigation scheduling programs since 1977; design and implementation of water conservation …

Avoiding Common Problems With Drip Tape, Charles M. Burt

BioResource and Agricultural Engineering

This publication is meant to help farmers, dealers, and manufacturers recognize and understand some of the problems that have been experienced with drip tape – problems that are quite different from manufacturing defects. Problems that are quickly detected and properly identified can often be remedied, or be avoided in the future. The report addresses drip tape damage caused by pests, installation, emitter pressure, plugging, and other categories.

Technical Concepts Related To Conservation Of Irrigation And Rain Water In Agricultural Systems, A. J. Clemmens, R. G. Allen, Charles M. Burt

BioResource and Agricultural Engineering

Forty percent of freshwater withdrawals in the United States are for irrigated agriculture, which contribute more than $50 billion to the economy. Increasing diversions of water for urban, environmental, and other uses will likely decrease water available to agriculture. Water conservation in agriculture is touted as a good method for minimizing the impact of reduced agricultural diversions on production. Because “wasted” water is often reused until it reaches the ocean, there are limitations to the true water savings that result from programs that aim to increase irrigation efficiency. True water savings can come from four areas: reduction of unnecessary evaporation …

Accuracy Of Global Microirrigation Distribution Uniformity Estimates, Stuart W. Styles, Charles M. Burt, Franklin Gaudi, Sierra Layous

BioResource and Agricultural Engineering

Emitter pressures and flow rates were systematically and extensively sampled in one drip and one microspray field. The data distributions are presented. The accuracy of rapid (limited samples) evaluation pressure sampling procedures was found to be quite good if the pressure distribution was systematic, but erroneous if the pressure distribution throughout a field was random. A simple mathematical combination of two nonuniformity components (due to pressure differences, and other causes of flow variation) provided a better estimate of overall system distribution uniformity than more complex mathematics.

Conversion To Groundwater Pumping With Drip/Micro Irrigation Systems, Charles M. Burt, Monte Soto

BioResource and Agricultural Engineering

Twenty one irrigation districts in the Central Valley reported “conversion acres”. Conversion acres are those on which farmers used only groundwater for drip/micro irrigation although surface irrigation water was available.

The twenty one districts include about 2 million acres of irrigated area. Approximately 3.6% of that acreage (73,000 acres) has been “converted” to groundwater when farmers switched to drip/micro. Fourteen of these districts anticipate more conversion in the future. ITRC thinks that the conversion will be more rapid and greater than district personnel suspect.

The dominant factor that influences the conversion was the lack of flexible water delivery service to …

Electric Motor Efficiency Under Variable Frequencies And Loads, Charles M. Burt, Xianshu Piao, Franklin Gaudi, Bryan Busch, N. F. N. Taufik

BioResource and Agricultural Engineering

This paper details a study performed by the Irrigation Training and Research Center to determine motor performances under varying speeds [induced by a variable frequency drives (VFD) controller] and loads. A further goal of the study was to provide sufficient information to designers so that they could estimate total pumping plant power usage with a VFD-controlled installation. Motors were tested with a VFD as well as across-the-line. On average, the relative efficiency of the electrical system with a VFD may be approximately 8% lower than the relative efficiency of a properly designed, full-load across-the-line system. If one considers actual field …

Simulated Effects Of Reflective Mulch On Energy And Water Conservation In Semi-Arid Central California Greenhouses, T. Mehlitz, Ilhami Yildiz, S. Rahman, C. Hardin

BioResource and Agricultural Engineering

In addition to the labor, energy and water consumption are the two main cost drivers in current greenhouse systems. Consequently, considerable effort is expended to conserve energy and water, and look for alternative energy sources. Greenhouses in hot and arid regions also require large quantities of water for irrigation. Proper environmental management systems can significantly change the energy and moisture dynamics of greenhouse production systems. This study aims to focus on reducing energy and water consumption in semi-arid California greenhouses. Influences of mulch (having different reflectivities) on energy and water conservation were investigated. The reflectivity of mulch used as a …

Design And Evaluation Of A Greenhouse Interface For Climate Control Programming And Networking, G. Diaz, S. F. Kelly, Ilhami Yildiz

BioResource and Agricultural Engineering

At Cal Poly the motto is “Learn by Doing”. In the College of Agriculture, this is especially true and many of the labs provide an opportunity for students to implement this philosophy. Updated climate controls were installed in a series of greenhouses on the top floor of the Agricultural Science building that are used for student and faculty research projects. A Programmable Logic Controller (PLC) was installed to actuate the various vents, shading, heating, cooling and irrigation. A control program was developed to control and log temperatures and other operating parameters to monitor the greenhouse. An easy to use computer …

Simulated Effects Of Various Environmental Management Practices On Energy Consumption In Open And Confined Greenhouse Systems, Ilhami Yildiz, D. P. Stombaugh

BioResource and Agricultural Engineering

The objective of this study was to evaluate the effects of relative humidity, light management levels, minimum ventilation rates, CO₂ enrichment and canopy size on energy consumption in three different greenhouse systems (conventional, open-loop heat pump, and confined heat pump) in winter, spring, and summer months. No difference was observed in energy consumption with relative humidity set point levels in winter due to the already low relative humidity levels. Some differences were observed in spring and summer due to extra dehumidification required to maintain the inside relative humidity at lower levels. Energy consumption in summer was reduced up to …

Irrigation District Energy Survey, Charles M. Burt, Daniel J. Howes

BioResource and Agricultural Engineering

This survey was completed by ITRC on behalf of the California Energy Commission Public Interest Energy Research (PIER) Program. The purpose of the survey was to establish a benchmark for the present status of the pumping systems used by agricultural water districts in California and to determine the districts' needs. The needs discussed involve technical assistance, research grant and low-interest loan funding, and district-related policy issues. Thirty agricultural water districts were selected for the survey. These districts were selected based on energy use per acre of irrigated area, size, geographic location, and distribution infrastructure.

Simulated Effects Of Dynamic Row Spacing On Energy And Water Conservation In Semi-Arid Central California Greenhouses, A. Moya, T. Mehlitz, Ilhami Yildiz, S. F. Kelly, C. Hardin

BioResource and Agricultural Engineering

Considerable effort is expended to conserve energy and water in current greenhouse systems, and look for alternative energy sources, especially passive heating and cooling strategies. Proper environmental management systems can significantly change the energy and moisture dynamics of greenhouse production systems. In this study, specifically, influences of dynamic row spacing on energy and water conservation were investigated. A dynamic computer simulation model was used to compare different row spacings, plant heights, and leaf dimensions to draw a conclusion about energy and water conservation. The results showed that using smaller spacings between cucumber crop rows (for instance, 0.5 m instead of …

Simulated Performance Of A Renewable Energy Technology – Heat Pump Systems In Semi-Arid California Greenhouses, C. Hardin, T. Mehlitz, Ilhami Yildiz, S. F. Kelly

BioResource and Agricultural Engineering

In addition to the labor, energy and water consumption are the two main cost drivers in current greenhouse systems. Consequently, considerable effort is expended to conserve energy and water, and look for alternative energy sources, especially environmentally friendly renewable energy sources and technologies. Greenhouses in hot and arid regions also require large quantities of water for irrigation. Using proper technologies and environmental management systems can significantly change the energy and moisture dynamics of greenhouse production systems. This study aims to focus on reducing natural gas, electricity, and water consumption in semi-arid California greenhouses introducing renewable energy heat pump technologies to …

Simulated Effects Of Various Environmental Management Practices On Water Consumption In Open And Confined Greenhouse Systems, Ilhami Yildiz, D. P. Stombaugh

BioResource and Agricultural Engineering

The objective of this study was to evaluate the effects of relative humidity, light management, minimum ventilation rates, CO₂ enrichment and canopy size on water consumption in three different greenhouse systems (conventional, open heat pump, and confined heat pump) in winter, spring, and summer months. Using different relative humidity set points resulted in almost the same relative humidity regimes within the confined greenhouse system, resulting in similar transpiration rates. No difference was observed in transpiration rates in the open system in winter either, because the inside relative humidity levels never reached the 70% and 80% set points. Some differences …

Spatial Distributions Of Heating, Cooling, And Industrial Degree-Days In Turkey, Ilhami Yildiz, B. Sosaoglu

BioResource and Agricultural Engineering

The degree-day method is commonly used to estimate energy consumption for heating and cooling in residential, commercial and industrial buildings, as well as in greenhouses, livestock facilities, storage facilities and warehouses. This article presents monthly and yearly averages and spatial distributions of heating, cooling, and industrial degree-days at the base temperatures of 18 °C and 20 °C, 18 °C and 24 °C, and 7 °C and 13 °C, respectively; as well as the corresponding number of days in Turkey. The findings presented here will facilitate the estimation of heating and cooling energy consumption for any residential, commercial and industrial buildings …