Design, Acnd Construction Of A Portable Artificial Insemination Chute, Chris Herrera

BioResource and Agricultural Engineering

This senior project report discusses the design, construction, and evaluation of a portable artificial insemination chute for the use of the Cal Poly Beef Department. The design was based on the suggested modifications from operators of several other chutes currently in use.

The main areas considered for the design were; Ergonomics, cattle safety, factors effecting maximum breeding conception rates, and Portability.

The breeding chute proved superior over traditional chutes in a variety of ways. Improvement occurred in the areas of consideration as follows, user operation was simplified, animal stress was decreased, and maximum breeding efficiency was obtained.

On-Farm Irrigation Tracking Software For The Imperial Valley, Taylor Andrew Brady

BioResource and Agricultural Engineering

In order to improve on farm irrigation, a water scheduling program specific to the needs of Imperial Valley farmers will be created. The program will help keep track of daily water schedules, as well as stay connected with the farm personnel to reduce error and save time. The program will help with on farm operations and productivity by allowing the famer, irrigation foremen, and secretary to view the same schedule simultaneously. The information that is inputted into the program will be editable by all the chosen personnel, to keep everyone on the same page. Weekly, monthly, or yearly usage reports …

Expansion Of A Dust Removal System For The Brae Department Plasma Table, Derek Hansen

BioResource and Agricultural Engineering

This senior project discusses the expansion of a dust removal system for welding and cutting fumes. A Donaldson Torit Powercore TG8 dust collector is used to collect and process the fumes created during welding and cutting operations that take place in the BioResource and Agricultural Engineering department at Cal Poly San Luis Obispo. Expansion of the system allows for greatly increased utilization of the TG8 and a cleaner working environment in Lab #6. Testing shows that the system fluently changes between the plasma table and the three hoods in the shop. Each hood is only capable of collecting a smoke …

Pump Performance With Sand Wear, Charles M. Burt, Kyle Fesit

BioResource and Agricultural Engineering

In many installations, pump performance declines over time due to sand wear. In order to pinpoint the type and rate of wear caused by pumping water with higher-than-average sand concentrations and its direct effect on various pump impeller materials, vertical pump impeller/bowl assemblies of approximately 900 GPM were each pumped for up to 2500 hours with high concentrations of sand in the water. Two different impeller materials were used for a total of five configurations. Well pump operation was simulated by maintaining a constant discharge pressure. The degrading performance, in terms of changing flow rate and kilowatt load, was recorded …

Spatial Variability In Evapotranspiration Related To Irrigation System Distribution Uniformity, Daniel J. Howes, Lucas Hoffmann, Franklin Gaudi

BioResource and Agricultural Engineering

Understanding the causes of variable ET in a field is critical for maximizing yield on a per-acre basis as well as for proper irrigation scheduling and regional water management. Since 2004, the ITRC has provided technical irrigation support and management for over 2,000 acres of center pivot irrigated forage crops being supplied by reclaimed water near Palmdale, California. Irrigation scheduling is conducted using a daily soil water balance dual crop coefficient approach. Detailed records on planting and harvest dates, daily water applications, pivot run speeds, and annual distribution uniformity evaluations are maintained along with daily reference evapotranspiration data from a …

Basin-Wide Remote Sensing Of Actual Evapotranspiration And Its Influence On Regional Water Resources Planning, Daniel J. Howes, Charles M. Burt, Kyle Feist

BioResource and Agricultural Engineering

The Irrigation Training & Research Center (ITRC) at Cal Poly State University, San Luis Obispo has been using METRIC to compute actual evapotranspiration from remote sensing sources (namely LandSAT images). The driving force behind this is the increasing need for improved evapotranspiration information on a large scale. A recent study in the Mexicali Valley of Baja California, Mexico utilized the ITRC-modified METRIC procedure to compute the crop and riparian evapotranspiration component of a basin-wide water balance. The resulting comparison between the mass balance computed change in groundwater storage and that computed using groundwater elevation data showed excellent agreement. For water …

Comparison Of Field Level And Regional Actual Etc Values Developed From Remote Sensing And Dual Crop Coefficient Procedure, Daniel J. Howes, Lucas Hoffmann, Franklin Gaudi

BioResource and Agricultural Engineering

Crop evapotranspiration (ETc) estimates are important for regional water planning as well as irrigation scheduling. Traditional ETc computations utilize published crop coefficients (basal) that are adjusted on a daily basis depending on soil water availability (i.e., dual crop coefficient method). Recent advancements include using remote sensing data such as LandSAT combined with a surface energy balance algorithm (METRIC), allowing crop evapotranspiration to be computed for each pixel throughout images taken during the season. There are limitations and advantages for both methods. Comparisons of soil water balance evapotranspiration values to METRIC values for two scenarios in different regions of California have …

Irrigation Engineering In Seismic Zones - Mexicali Valley, Mexico, Alan Dennis Gracia, Charles M. Burt, Mario Paredes Vallejo

BioResource and Agricultural Engineering

On April 4, 2010 an earthquake of Richter magnitude 7.2 occurred with an epicenter south of Mexicali within the irrigated zone of Mexicali Valley. Extensive damage occurred to main and lateral canal structures, plus to field irrigation systems and the main drainage network. This paper describes the engineering for a new major irrigation water conveyance system to service the most heavily impacted zone of 80,000 acres. Considerations included identification of the causes of the damage, selection of canal versus pipeline, relocation costs of people along new routes, and improved flexibility of water delivery. Major investigations regarding soils, topography, etc. were …

Velocity Contour Weighting Method. Ii: Evaluation In Trapezoidal Channels And Roughness Sensitivity, Daniel Howes, Brett F. Sanders

BioResource and Agricultural Engineering

The Velocity Contour Weighting Method (VCWM) was developed in Part I to accurately estimate the cross-sectional average velocity of a prismatic channel flow using acoustic Doppler velocity meter (ADVM) measurements of centerline velocity. Here, the VCWM is validated by its successful application to 25 different concrete-lined trapezoidal channels used for irrigation water delivery. At each site, the cross-sectional distribution of velocity is measured by an acoustic Doppler velocimeter (ADV), which is moved horizontally and vertically through a sampling grid. Multiple tests at some sites led to a total of 51 sets of cross-sectional measurements. ADVM measurements are simulated by interpolating …

Velocity Contour Weighting Method. I: Algorithm Development And Laboratory Testing, Daniel J. Howes, Brett F. Sanders

BioResource and Agricultural Engineering

An algorithm is developed for real-time estimation of the cross-sectional average velocity of a channel flow by using an upward-looking pulsed wave acoustic Doppler velocity meters (ADVM). The Velocity Contour Weighting Method (VCWM) is applicable to gradually varied flows in prismatic channels and requires little to no calibration. VCWM estimates the average velocity as a weighted average of ADVM bin velocities. Weights are based on the velocity distribution sampled by the ADVM. Collectively, the VCWM is able to adapt to a wide range of channel geometry and roughness features. Expressions for the velocity weights are developed by first applying a …

Agricultural Irrigation Using Municipal Effluent, Charles M. Burt

BioResource and Agricultural Engineering

The paper describes the development of a design and management plan for disposing of secondary effluent originating in the urban communities. It highlights the differences in approach that a public utility must take, versus a typical agricultural irrigation application. Costs and requirements for municipal effluent irrigation are many times greater. The complexity of regulations and agency procurement procedures relegates the actual irrigation system design to a relatively small role in the total project.

The Irrigation Sector Shift From Construction To Modernization: What Is Required For Success?, Charles M. Burt

BioResource and Agricultural Engineering

External pressures related to environmental protection, commodity prices, energy availability, larger populations, and climate change have combined to require an immediate and substantial improvement in agricultural irrigation performance. Worldwide progression towards modernized irrigation projects has been uneven and slower than desired, but decades of irrigation modernization development have clarified certain requirements for success, as well as illuminated indicators of project failure. Of particular importance are required shifts within the state and national irrigation bureaucracies, as well as universities.

Effects Of Sprinkler, Partial Sprinkler/Drip, And Drip Only Irrigation On Strawberry Transplants 2010-2011, Stuart Styles

BioResource and Agricultural Engineering

The purpose of the project is to develop an analysis of the current irrigation practices of the strawberry growers on the Central Coast of California. The primary research evaluation is during the establishment of transplants where sprinklers are typically used even though drip irrigation is available. Growers have been selected from Oxnard, Santa Maria, and Watsonville to provide a good cross section of the different strawberry growing areas.

The specific objectives of the project are to: (1) set up a research areas and control plots on a demonstration scale, (2) determine the key factors that affect the problems in early …

Design, Construction And Evaluation Of Seven Shank, Three Point Ripper, Daniel Degraaf

BioResource and Agricultural Engineering

This senior project discusses the design, construction, and testing of a seven shank, three point ripper built for de Graaf Ranch. This ripper will replace older equipment that was not built to withstand the horsepower developed by more modern tractors that are used by de Graaf Ranch. This tillage device is designed to meet ASABE standards for horsepower requirements of farm equipment. This implement incorporates a shear pin design that will protect the frame from damage in the event that the ripper encounters a subsoil obstacle that would significantly damage the equipment. The shank was designed to reduce the disturbance …

Design And Cost Analysis Of A Citrus Orchard, Travis Cox

BioResource and Agricultural Engineering

No abstract provided.

Development Of A Testing Procedure Using Cone Index To Allow For Optimal Tire Performance, Ryan Pehle

BioResource and Agricultural Engineering

This project discusses the design, fabrication, and evaluation of a Soil Cone Penetrometer that is to be used to test tracks designated for modified tractor pulling. The penetrometer measures the force required to penetrate a soil and provides a recommended tire pressure specific for the conditions present at the point in time

Design, Construction And Evaluation Of An Automotive Bridge Jack, Thomas Gomes Jr.

BioResource and Agricultural Engineering

This Senior Project discusses the design, construction and evaluation of an automotive lift. This lift will be hydraulically powered with a 6000 lb lifting capacity. The lift constructed in this project will be installed within a current 4 post drive on vehicle lift and allows the user to lift one axle of a vehicle a few inches off the ramp of the drive on lift in order to remove the tires.

Strawberries: Effects Of Modifying Irrigation Methods For Transplant Establishment, Stuart Styles, Lynn Groundwater, Curtis Lutje

BioResource and Agricultural Engineering

In 2009, the Cal Poly Irrigation Training and Research Center began a multi-year analysis of the current irrigation practices of strawberry growers on the Central Coast of California. Specifically, the project examines the impacts of salinity on young strawberry transplants and the current practice of sprinkler use during the establishment of transplants for salinity control in areas where drip irrigation is available. The overall goal of the project is to study current practices and determine any conditions where growers can minimize or eliminate sprinkler use on strawberries, thereby conserving water, saving pumping costs, and reducing runoff. Results from the first …

Implementation And Field Calibration Pipeline Doppler Meters In Northern California, Stuart Styles

BioResource and Agricultural Engineering

The Tehama-Colusa Canal Authority (TCCA) has been using SonTek Doppler flow meters at approximately 30 installations for about 3 years. TCCA is located in northern California with its headquarters in Willows. The Cal Poly ITRC compared the accuracy of the flow measurement readings from the new Doppler flow meters to the venturi meters that were installed by the US Bureau of Reclamation (USBR). The venturis were used as the historical standard for flow measurement for TCCA. TCCA has opted to move away from the existing technology for a variety of reasons, especially due to the issue concerning access requirements for …

Characteristics Of Irrigation Pump Performance In Major Irrigated Areas Of California, Charles Burt

BioResource and Agricultural Engineering

Pumping data was collected from over 15,000 well and non-well pumps throughout the Sacramento, Salinas, and San Joaquin Valley groundwater basins of California. Each of these basins is divided into a number of subbasins. A map of the general layout is shown below (gray lines outside of basins represent county lines; gray lines inside basins represent subbasins).

Data was analyzed by basin and subbasin for well pumps and non-well pumps. For each pump type, averages were calculated based on:

• The whole basin
• Overall pumping plant efficiency (OPPE)
• kWh/AF
• Subbasins

General conclusions were drawn for each set of averages, and a …

Irrigation System Components And Potentials For Energy Conservation, Charles M. Burt

BioResource and Agricultural Engineering

On-site electricity conservation in irrigation can be accomplished through a series of general steps. The primary focus of the agricultural energy conservation programs of the utilities has been to improve the efficiency of the pumping plant. In general, the electric utilities have provided or subsidized pump testing, along with some form of rebate for replacement or repair of pumps. There are, of course, other irrigation-related aspects of energy conservation. However, this report focuses on on-site electricity conservation in the field.

Design Of A Micro Irrigation System For An Almond Orchard, Adam Scheuber

BioResource and Agricultural Engineering

The owners of Scheuber Farms, a 1,000 acre row crop farming operation located in Patterson, California, wish to convert a 15-acre field into an almond orchard. For irrigating the trees, they would like to use a microsprayer irrigation system. The design I recommend and describe in this paper utilizes proper hydraulic analysis, and is based on the ability to supply enough water to match the amount of water required by the orchard during the peak month of an average year.

All of the major components and parameters of the microsprayer irrigation system were designed at minimal cost while ensuring that …

Agricultural Water Energy Efficiency: Final Report, Charles M. Burt, Dan J. Howes, Beau Freeman

BioResource and Agricultural Engineering

Beginning in 2007, the Irrigation Training and Research Center (ITRC) at California Polytechnic State University, San Luis Obispo, contracted with the California Energy Commission’s (CEC) Public Interest Energy Research (PIER) Program to undertake a large, multi-tiered study on agricultural water energy efficiency in California. The study was broken into the following research tasks: Task 1: Administrative; Task 2.1: Irrigation district energy survey; Task 2.2: Conversion to groundwater pumping with drip/ micro irrigation systems; Task 2.3: GIS-based water scheduling and software system; Task 3: Irrigation component energy analysis; Task 4: RD&D competitive solicitation; Task 5; Technology transfer. The resulting survey, research, …

Pipeline Design For Reclaimed Spill Water For West Stanislaus Irrigation District, Daniel Bays

BioResource and Agricultural Engineering

The goal of this project was to design a pipeline that could be installed to replace an existing drain in West Stanislaus Irrigation District.  The pipeline would give the district the ability to divert drain water back into their delivery system or send water down the existing drain.

The design attempted to use pipe and material the district already has and provided construction drawings and installation instructions for the construction of this design in the future.

Economic Analysis Of Reverse Osmosis Desalination Of Water For Agricultural Irrigation Applications, Ashley Hemping

BioResource and Agricultural Engineering

The combination of an ever-increasing population and a diminishing usable water supply threatens the sustainability of humanity’s existence on a global scale, especially in California, where agriculture is so integral to the state’s economy.  Due to widespread recognition of this problem, there has been a growing trend in the development of alternative water resources, one of which involves the desalination of salt or brackish waters.  Several different desalination technologies exist, including microfiltration, multi-stage flash, and multi-effect distillation.

This senior project investigates the economic viability of implementing reverse osmosis desalination for treatment of agricultural wastewater or other unusable water sources.  These …

Gis-Based Irrigation District Flow Routing/Scheduling, Charles M. Burt, Beau Freeman

BioResource and Agricultural Engineering

In 2007, the Irrigation Training and Research Center (ITRC) at California Polytechnic State University, San Luis Obispo undertook to develop a prototype of an intelligent and scalable real-time GIS-based water scheduling and routing software system for irrigation districts, capable of integrating multiple data sources into an information access and management facility featuring collaborative tools with automatic reasoning and analytical capabilities. Improving the infrastructure and management capabilities of irrigation districts in order to provide flexible delivery schedules and increase participation in peak demand reduction programs has been identified as having a significant potential to achieve energy conservation and resource efficiencies.

The …

Variable Frequency Drive (Vfd) Controlled Irrigation Pumps – Analysis Of Potential Rebate, Charles M. Burt

BioResource and Agricultural Engineering

Well pumps, booster pumps, and a combination of the two are used throughout the agricultural sector to provide water for on-farm irrigation. However, the pump discharge pressures for the majority of irrigation systems are excessive, waiving considerable monetary and power consumption savings. This report analyzes the numerous potential benefits of integrating a variable frequency drive (VFD) to irrigation supply systems and modifying system design philosophies.

Irrigation District Flow Metering, Charles M. Burt

BioResource and Agricultural Engineering

Most readers of this publication are probably somewhat familiar with USBR Reclamation Reform Act requirements for measurement of water deliveries to farm turnouts, in cases where the water is supplied by Reclamation facilities. Basically, volumes within the Mid-Pacific Region are supposed to be measured within ±6%. This sounds like a fairly straightforward requirement, but the reality is anything but simple.

The Irrigation Sector Shift From Construction To Modernization: What Is Required For Success?, Charles M. Burt

BioResource and Agricultural Engineering

External pressures related to environmental protection, commodity prices, energy availability, larger populations, and climate change have combined to require an immediate and substantial improvement in agricultural irrigation performance. Worldwide progression towards modernized irrigation projects has been uneven and slower than desired, but decades of irrigation modernization development have clarified certain requirements for success, as well as illuminated indicators of project failure. Of particular importance are required shifts within the state and national irrigation bureaucracies, as well as universities.

Motor Reference, Mohamed Grissa

BioResource and Agricultural Engineering

This document contains summary information about the following motor topics:

• Motor selection information
• AC induction motors
• Inverter duty motors
• Variable frequency drives
• Motor losses
• Troubleshooting

The information contained in this document was gathered from a variety of online, interview, and print sources, including NEMA specifications, with support from the California Energy Commission (CEC) PIER Program.