Design, Construction And Evaluation Of Seven Shank, Three Point Ripper, Daniel Degraaf

BioResource and Agricultural Engineering

This senior project discusses the design, construction, and testing of a seven shank, three point ripper built for de Graaf Ranch. This ripper will replace older equipment that was not built to withstand the horsepower developed by more modern tractors that are used by de Graaf Ranch. This tillage device is designed to meet ASABE standards for horsepower requirements of farm equipment. This implement incorporates a shear pin design that will protect the frame from damage in the event that the ripper encounters a subsoil obstacle that would significantly damage the equipment. The shank was designed to reduce the disturbance …

Design And Cost Analysis Of A Citrus Orchard, Travis Cox

BioResource and Agricultural Engineering

No abstract provided.

Development Of A Testing Procedure Using Cone Index To Allow For Optimal Tire Performance, Ryan Pehle

BioResource and Agricultural Engineering

This project discusses the design, fabrication, and evaluation of a Soil Cone Penetrometer that is to be used to test tracks designated for modified tractor pulling. The penetrometer measures the force required to penetrate a soil and provides a recommended tire pressure specific for the conditions present at the point in time

Design, Construction And Evaluation Of An Automotive Bridge Jack, Thomas Gomes Jr.

BioResource and Agricultural Engineering

This Senior Project discusses the design, construction and evaluation of an automotive lift. This lift will be hydraulically powered with a 6000 lb lifting capacity. The lift constructed in this project will be installed within a current 4 post drive on vehicle lift and allows the user to lift one axle of a vehicle a few inches off the ramp of the drive on lift in order to remove the tires.

Strawberries: Effects Of Modifying Irrigation Methods For Transplant Establishment, Stuart Styles, Lynn Groundwater, Curtis Lutje

BioResource and Agricultural Engineering

In 2009, the Cal Poly Irrigation Training and Research Center began a multi-year analysis of the current irrigation practices of strawberry growers on the Central Coast of California. Specifically, the project examines the impacts of salinity on young strawberry transplants and the current practice of sprinkler use during the establishment of transplants for salinity control in areas where drip irrigation is available. The overall goal of the project is to study current practices and determine any conditions where growers can minimize or eliminate sprinkler use on strawberries, thereby conserving water, saving pumping costs, and reducing runoff. Results from the first …

Implementation And Field Calibration Pipeline Doppler Meters In Northern California, Stuart Styles

BioResource and Agricultural Engineering

The Tehama-Colusa Canal Authority (TCCA) has been using SonTek Doppler flow meters at approximately 30 installations for about 3 years. TCCA is located in northern California with its headquarters in Willows. The Cal Poly ITRC compared the accuracy of the flow measurement readings from the new Doppler flow meters to the venturi meters that were installed by the US Bureau of Reclamation (USBR). The venturis were used as the historical standard for flow measurement for TCCA. TCCA has opted to move away from the existing technology for a variety of reasons, especially due to the issue concerning access requirements for …

Characteristics Of Irrigation Pump Performance In Major Irrigated Areas Of California, Charles Burt

BioResource and Agricultural Engineering

Pumping data was collected from over 15,000 well and non-well pumps throughout the Sacramento, Salinas, and San Joaquin Valley groundwater basins of California. Each of these basins is divided into a number of subbasins. A map of the general layout is shown below (gray lines outside of basins represent county lines; gray lines inside basins represent subbasins).

Data was analyzed by basin and subbasin for well pumps and non-well pumps. For each pump type, averages were calculated based on:

• The whole basin
• Overall pumping plant efficiency (OPPE)
• kWh/AF
• Subbasins

General conclusions were drawn for each set of averages, and a …

Irrigation System Components And Potentials For Energy Conservation, Charles M. Burt

BioResource and Agricultural Engineering

On-site electricity conservation in irrigation can be accomplished through a series of general steps. The primary focus of the agricultural energy conservation programs of the utilities has been to improve the efficiency of the pumping plant. In general, the electric utilities have provided or subsidized pump testing, along with some form of rebate for replacement or repair of pumps. There are, of course, other irrigation-related aspects of energy conservation. However, this report focuses on on-site electricity conservation in the field.

Design Of A Micro Irrigation System For An Almond Orchard, Adam Scheuber

BioResource and Agricultural Engineering

The owners of Scheuber Farms, a 1,000 acre row crop farming operation located in Patterson, California, wish to convert a 15-acre field into an almond orchard. For irrigating the trees, they would like to use a microsprayer irrigation system. The design I recommend and describe in this paper utilizes proper hydraulic analysis, and is based on the ability to supply enough water to match the amount of water required by the orchard during the peak month of an average year.

All of the major components and parameters of the microsprayer irrigation system were designed at minimal cost while ensuring that …

Agricultural Water Energy Efficiency: Final Report, Charles M. Burt, Dan J. Howes, Beau Freeman

BioResource and Agricultural Engineering

Beginning in 2007, the Irrigation Training and Research Center (ITRC) at California Polytechnic State University, San Luis Obispo, contracted with the California Energy Commission’s (CEC) Public Interest Energy Research (PIER) Program to undertake a large, multi-tiered study on agricultural water energy efficiency in California. The study was broken into the following research tasks: Task 1: Administrative; Task 2.1: Irrigation district energy survey; Task 2.2: Conversion to groundwater pumping with drip/ micro irrigation systems; Task 2.3: GIS-based water scheduling and software system; Task 3: Irrigation component energy analysis; Task 4: RD&D competitive solicitation; Task 5; Technology transfer. The resulting survey, research, …

Pipeline Design For Reclaimed Spill Water For West Stanislaus Irrigation District, Daniel Bays

BioResource and Agricultural Engineering

The goal of this project was to design a pipeline that could be installed to replace an existing drain in West Stanislaus Irrigation District.  The pipeline would give the district the ability to divert drain water back into their delivery system or send water down the existing drain.

The design attempted to use pipe and material the district already has and provided construction drawings and installation instructions for the construction of this design in the future.

Economic Analysis Of Reverse Osmosis Desalination Of Water For Agricultural Irrigation Applications, Ashley Hemping

BioResource and Agricultural Engineering

The combination of an ever-increasing population and a diminishing usable water supply threatens the sustainability of humanity’s existence on a global scale, especially in California, where agriculture is so integral to the state’s economy.  Due to widespread recognition of this problem, there has been a growing trend in the development of alternative water resources, one of which involves the desalination of salt or brackish waters.  Several different desalination technologies exist, including microfiltration, multi-stage flash, and multi-effect distillation.

This senior project investigates the economic viability of implementing reverse osmosis desalination for treatment of agricultural wastewater or other unusable water sources.  These …

Gis-Based Irrigation District Flow Routing/Scheduling, Charles M. Burt, Beau Freeman

BioResource and Agricultural Engineering

In 2007, the Irrigation Training and Research Center (ITRC) at California Polytechnic State University, San Luis Obispo undertook to develop a prototype of an intelligent and scalable real-time GIS-based water scheduling and routing software system for irrigation districts, capable of integrating multiple data sources into an information access and management facility featuring collaborative tools with automatic reasoning and analytical capabilities. Improving the infrastructure and management capabilities of irrigation districts in order to provide flexible delivery schedules and increase participation in peak demand reduction programs has been identified as having a significant potential to achieve energy conservation and resource efficiencies.

The …

Canal Lining, Charles M. Burt

BioResource and Agricultural Engineering

Larry and I thought that some musings about canal lining might be of some interest for some of you USCID newsletter readers. As you know, there are many canal lining techniques – especially if one considers the wide assortment of internationally used lining methods.

Variable Frequency Drive (Vfd) Controlled Irrigation Pumps – Analysis Of Potential Rebate, Charles M. Burt

BioResource and Agricultural Engineering

Well pumps, booster pumps, and a combination of the two are used throughout the agricultural sector to provide water for on-farm irrigation. However, the pump discharge pressures for the majority of irrigation systems are excessive, waiving considerable monetary and power consumption savings. This report analyzes the numerous potential benefits of integrating a variable frequency drive (VFD) to irrigation supply systems and modifying system design philosophies.

Low Pressure Drip/Micro System Design – Analysis Of Potential Rebate, Charles M. Burt, Daniel J. Howes

BioResource and Agricultural Engineering

Drip/micro irrigation systems are often referred to as “low pressure” systems because the required emitter pressures are relatively low (6-12 psi). However, the pump discharge pressures of systems on flat ground throughout California average 40 psi. This report examines readily attainable system losses by examining individual components of the drip/micro system.

Irrigation District Flow Metering, Charles M. Burt

BioResource and Agricultural Engineering

Most readers of this publication are probably somewhat familiar with USBR Reclamation Reform Act requirements for measurement of water deliveries to farm turnouts, in cases where the water is supplied by Reclamation facilities. Basically, volumes within the Mid-Pacific Region are supposed to be measured within ±6%. This sounds like a fairly straightforward requirement, but the reality is anything but simple.

Characteristics Of Pump Performance In Major Irrigated Areas Of California, Sierra A. Orvis Layous, Charles M. Burt, Luis P. Urrestarazu

BioResource and Agricultural Engineering

Well pump tests (12,876) in three Central California groundwater basins were characterized and described according to their spatial distribution. The average overall pumping plant efficiency (wire-water, not including column losses and velocity head) was about 56%. Characteristics such as drawdown, total dynamic heads, kW, and flow rate vary greatly between pumps within and between sub-basins. This is the first well pump characterization of its type in California, although irrigation pump tests have been conducted for over 70 years in California. This paper provides a summary of the spatial variation of well pump performance and characteristics.

The Irrigation Sector Shift From Construction To Modernization: What Is Required For Success?, Charles M. Burt

BioResource and Agricultural Engineering

External pressures related to environmental protection, commodity prices, energy availability, larger populations, and climate change have combined to require an immediate and substantial improvement in agricultural irrigation performance. Worldwide progression towards modernized irrigation projects has been uneven and slower than desired, but decades of irrigation modernization development have clarified certain requirements for success, as well as illuminated indicators of project failure. Of particular importance are required shifts within the state and national irrigation bureaucracies, as well as universities.

Motor Reference, Mohamed Grissa

BioResource and Agricultural Engineering

This document contains summary information about the following motor topics:

• Motor selection information
• AC induction motors
• Inverter duty motors
• Variable frequency drives
• Motor losses
• Troubleshooting

The information contained in this document was gathered from a variety of online, interview, and print sources, including NEMA specifications, with support from the California Energy Commission (CEC) PIER Program.

Drip Irrigation System Cost Sharing By Irrigation Districts For Water Conservation, Charles M. Burt

BioResource and Agricultural Engineering

Government and irrigation district cost sharing programs have often included financial support for the installation of drip/micro irrigation systems. These programs seek advantages that might include improved crop yield, less applied water, and a reduction in subsurface drainage water and surface tailwater. They may also seek to reduce water consumption. The actual results have been shown to vary by district, hydrology, and crop.

It is true that drip systems in California, on average, have good Distribution Uniformities (DU) of irrigation water – meaning that there are only minor differences between the depths of water received by various plants throughout a …

Irrigation District Turnouts, Charles M. Burt

BioResource and Agricultural Engineering

This is meant to be a very quick, roughly written primer on irrigation district turnout selection. It by no means covers all of the details, but it might help out. ITRC offers flow measurement classes, with online registration at www.itrc.org. We have also done testing on quite a few designs over the years, but the work was almost all confidential in nature.

Modernización De Proyectos De Riego, Charles M. Burt

BioResource and Agricultural Engineering

Un diseño moderno es el resultado de un proceso de reflexión, el cual selecciona la configuración y componentes físicas considerando un programa de operación bien definido y realista basado en el concepto de servicio.

Medición De Gasto En Canales De Riego Y...Otras Cosas, Charles M. Burt

BioResource and Agricultural Engineering

Nuestra opción preferida para Eiqupos de “flujo crítico ” (vertedor or aforador) son Aforadores Replogle (Garganta Larga)

Subcritical Contraction For Improved Open-Channel Flow Measurement Accuracy With An Upward-Looking Advm, Daniel Howes, Charles M. Burt, Brett F. Sanders

BioResource and Agricultural Engineering

Acoustic Doppler velocity meters (ADVMs) provide an alternative to more traditional flow measurement devices and procedures such as flumes, weirs, and stage rating for irrigation and drainage canals. However, the requirements for correct calibration are extensive and complex. A three-dimensional computational fluid dynamics (CFD) model was used to design a subcritical rapidly varied flow contraction that provides a consistent linear relationship between the upward-looking ADVM sample velocity and the cross-sectional average velocity in order to improve ADVM accuracy without the need for in situ calibration. CFD simulations validated the subcritical contraction in a rectangular and trapezoidal cross section by showing …

Commercial Sand Media Filter Tank Criteria For Energy Efficiency - Agricultural Drip Irrigation, Charles M. Burt

BioResource and Agricultural Engineering

Sand media filters are commonly used in agricultural drip irrigation systems. They have the advantages of simplicity and large capacities, and are favored by many farmers and designers over other filtration hardware. The primary justification for the research described in this report was to determine if it is possible and reasonable to use lower-than-accepted backflush pressures and thereby reduce the total pressure requirement for drip systems.

Strawberries: Effects Of Modifying Irrigation Methods For Transplant Establishment 2009-2010, Stuart Styles

BioResource and Agricultural Engineering

The purpose of the project is to develop an analysis of the current irrigation practices of the strawberry growers on the Central Coast of California. The primary research evaluation is during the establishment of transplants where sprinklers are used even though drip irrigation is available. This project has targeted the impacts of salinity on the young strawberry transplants.

The specific objectives of the project are to: (1) Set up a research areas and control plots on a demonstration scale, (2) determine the key factors that affect the problems in early growth of transplanted strawberries, (3) determine relationships between the use …

Practical Experience With State-Of-The-Art Technologies In Scada Systems, Beau Freeman, Charles M. Burt

BioResource and Agricultural Engineering

A Supervisory Control and Data Acquisition (SCADA) system is a powerful tool which, when implemented properly in irrigation districts, can lead to improved water delivery service to farms, more effective operations, reduced spill (and therefore reduced diversions), and in some cases a reduction in costs (less labor, less energy, etc.). However, widespread adoption of SCADA and automation technologies remains a technical and financial challenge for most irrigation districts. In spite of many good hardware and software products available on the market now, putting all the pieces together requires specialized expertise. Nevertheless, by following some straightforward strategies and rules of good …

Pump Operation With Vfd Controlled Motors, Charles M. Burt

BioResource and Agricultural Engineering

There are numerous reasons to consider using a VFD (variable frequency drive) controller with pumps in irrigation and drainage.These include: 1

1. Proper matching of the pump characteristics with the system. Reasonable engineers and salespersons will almost always overdesign pumps. It is very simple – if the pump is too small, there will be complaints. If, on the other hand, the pump delivers a bit more pressure than needed, there is rarely a complaint. Reasons to overdesign include:

Where Is All That Water Going?, Charles M. Burt

BioResource and Agricultural Engineering

Some have proposed to conserve 4-6 Million AF/yr in Agriculture with pragmatic, economical measures. All we need to do is find the inefficiencies. Then we'll get rid of them.