Bioresource and Agricultural Engineering Commons^™

Bioflocculation Of Wastewater Treatment Pond Suspended Solids, Louis Lefebvre

Master's Theses

Bioflocculation of Wastewater Treatment Pond Suspended Solids

Louis Lefebvre

Wastewater treatment lagoons and high rate algae ponds (HRAPs) can provide cost effective wastewater treatment, but they commonly have high effluent concentrations of total suspended solids (TSS). In this thesis algae pond effluent was treated in a beaker testing apparatus (mixed and aerated) with various mixtures of activated sludge and primary effluent simulating differing activated sludge aeration basin compositions then was allowed to settle to assess settleability. Conventionally, microalgal suspended solids are removed by chemical coagulation followed by separation methods that often have a high cost relative to the low cost …

Design, Fabrication And Manufacturing Analysis Of A Rollover Protection System, Nikolas Paris

BioResource and Agricultural Engineering

This senior project discusses the design, fabrication and manufacturing analysis of a rollover protection system specifically designed for early body style Ford Broncos (1966-1977). The rollover protection system, or roll cage, is an integral safety feature on vehicles which commonly encounter extreme terrain conditions. Many vehicles which attempt to traverse terrain such as this are not always properly equipped with a rollover protection system. This is the case with the early body style Ford Bronco. This system will be designed to market the niche of early bronco parts.

Modernization Of House #3: Improving Greenhouse Cut Flower Production And Students' Experience By Modernizing House #3, Kristina Anton

Biomedical Engineering

This paper documents the modernization of the black cloth, lighting, shade, and support systems in one of Cal Poly's on-campus, student operated cut flower production greenhouses. Problems with the old system are examined along with design requirements for a new system. Alternate designs are considered along with the installation process of the chosen design.

Sbx7 Flow Rate Measurement Compliance For Agricultural Irrigation Districts, Charles M. Burt, Evan Geer

BioResource and Agricultural Engineering

Senate Bill x7-7 (SBx7-7) requires documented volumetric accounting to individual turnouts for water deliveries. Section 597.3 of the bill lists two very different requirements for devices. This document examines the requirements of SBx7 and the implications for agricultural irrigation districts. The definitions and impacts of flow rate and volumetric accuracy are defined. Example scenarios and solutions are offered, as well as descriptions of applicable devices.

Effects Of Sprinkler, Partial Sprinkler/Drip, And Drip Only Irrigation On Strawberry Transplants 2011-2012, Stuart Styles

BioResource and Agricultural Engineering

The Cal Poly Irrigation Training and Research Center (ITRC), in collaboration with academic, water district, and industry partners, proposes to evaluate new strategies for drip irrigation on strawberries to minimize runoff during transplant establishment.

The most common method used for irrigating strawberries is a mix of sprinkler irrigation and drip. Growers use sprinkler irrigation for bed preparation and salinity control, then eventually switch to drip irrigation after transplanting, but continue to use sprinkler irrigation as an insurance policy (for bonding between plant roots and soil bonding, washing off the leaves, controlling salinity, and frost). However, field observations have shown that …

Water And Energy Conservation Grow System: Aquaponics And Aeroponics With A Cycle Timer, Roger Hancock

Electrical Engineering

What some experts call the “blue gold”; water is a major issue in this world. There is only so much water and the reliability and cleanliness of water is what many developing countries are dealing with today. Countries around the world are facing problems with reliable water to grow enough food for their villages and homes. Is there is a way to minimize water consumption while optimizing growth in plants for food? One solution can be seen through both Aeroponics and Aquaponics. This project explores the potential of providing larger quantities of food to areas where water may be in …

Implementation Of Magnetic Meters For Irrigation Volumetric Measurement, Stuart Styles, Lynn Groundwater

BioResource and Agricultural Engineering

The irrigation industry is experiencing a growth in the use of magnetic meters for measuring the flow rate and volume in irrigation pipelines. Historically, propeller meters have been the device selected by users. New legislation in California (SB7x7) will require measurement devices at key locations for irrigation water delivery. Some users are very interested in the magnetic meter for making the measurement at the turnout or farm gate. The key feature of the new meter is the ability for the device to work in less than ideal flow conditions. Electromagnetic meters have been tested by the Irrigation Training and Research …

Irrigation System Evaluation And Pump Efficiency, Gregory Borges

BioResource and Agricultural Engineering

This project encompasses the Evaluation of a drip irrigation system for a Pistachio orchard in Tulare, Ca. The project parameters were decided on by Borges Farms. After the evaluation suggestions are to be made for improving the system’s efficiency. These suggestions must be approved by the grower and show whether they are cost efficient. The irrigation system cannot be modified to fit the pump chosen.

Research for the project encompasses drip irrigation systems, irrigation pump efficiency, irrigation management, well reclamation techniques and pistachio water requirements. A Distribution Uniformity evaluation was performed to understand how sand has affected the system. I …

Evaluation, Design, And Testing Of Plc Data Logging System On Modified Pulling Tractor, Jared Evers

BioResource and Agricultural Engineering

This senior project involves the design and implementation of a data logging system on a modified pulling tractor, Mustang Fever. The project starts out a continuation of a previous project. The original goal of the project was to keep the Cal Poly Tractor Pull on the leading edge of innovation. The implementation of a sensor array and logging system on a modified pull tractor assists with the maintenance and tuning of the machine. The collected data is stored on a USB drive to allow analysis in the future.

The parameters collected by the system are: pressures, temperatures, and rotational speeds. …

Design, Construction, And Testing Of An Almond Harvester Pick-Up Belt Tensioning Mechanism, Brandon Eller

BioResource and Agricultural Engineering

This senior project presents the design, fabrication, and testing of a tensioning mechanism for an almond harvester pick-up belt system. This tensioner was intended to reduce belt tension spikes when obstructions are encountered in the system, and was tested on a previously fabricated pick-up belt test stand. The result of this project is a prototype tensioner mechanism that was tested with favorable results. Also, the project includes a results and discussion section that presents an improved design based on the testing results.

Design, Construction And Testing Of A Walnut Cracker, Michael Dasso

BioResource and Agricultural Engineering

This senior project involves the design, construction and testing of a walnut cracker for Beecher Lane Walnut of Stockton California. This prototype cracker is one piece of a walnut processing system to package walnuts. Beecher Lane Walnut currently utilizes a conical cracker design whereas this new design entails a twin barrel configuration.

The goal of this project was to design, construct and test a prototype walnut cracker that would help determine the variables necessary to yield the highest percentage of walnut halves.

The testing of this walnut cracker involved two varieties: Eureka and Chandler. Testing indicated the optimal output of …

Design And Fabrication Of A Concrete Washout Bin, Bryce Allen Dafonte

BioResource and Agricultural Engineering

The project encompassed the design and fabrication of a concrete washout bin. The design parameters were provided by feedback from multiple professors who have used the current concrete washout area, and would like a newer, more effective washout bin to use for multiple lab sessions throughout the school year. The concrete washout bin needed to be large enough to hold excess amounts of waste materials, yet include a low profile to aid the students in being able to clean multiple mixers and tools. A liner will be held in place to ensure that water does not leak out, but also …

Solid Set Sprinkler Design For An Apricot Orchard, Kyle Moeller

BioResource and Agricultural Engineering

The goal of this project was to design a solid set sprinkler system as well as a cost analysis for a 60 acre field. This allows for water to be distributed throughout an entire field at low flow rates allowing water to be used more efficiently and effectively. Completing a design such as this will allow some cost saving by the farmer throughout the systems use.

Implementation, Design, And Cost Analysis Of A Concrete Washout System, Omar Adina

BioResource and Agricultural Engineering

With the increase of environmental pollution in today’s world, many strategies and regulations are being enforced. These enforcements come from the state and federal governments, but public awareness is often overlooked. Stormwater regulations here in California have dramatically changed over the last decade, as the topic is investigated more often.

This senior project encompassed the design prototype and cost analysis of a permanent concrete washout station for the BioResource and Agricultural Engineering Department at California Polytechnic State University, San Luis Obispo. The design parameters given were to construct a steel bin for the excess concrete to be dumped into during …

Wine Grape Irrigation Management, Charles M. Burt

BioResource and Agricultural Engineering

This report addresses difficulties in calculating correct ET values for wine grapes, and includes tips for wine grape irrigation scheduling, regulated deficit irrigation, and soil moisture measurement, and crop canopy cover estimates.

The Effect Of Chlorine And Ozone In Controlling Microbes On Organically Grown Cilantro And Carrots, Adam Holtz

BioResource and Agricultural Engineering

This senior project investigates the relative efficacy of ozonated water and chlorinated water for the purpose of sanitizing freshly-harvested organic produce. The aim of this study was to assist the Cal Poly Organic Farm in deciding whether or not to invest in an ozone generator. The crops used for testing were grown organically in the same field. Carrots and cilantro were harvested and promptly treated with 5 ppm ozone solution or 25 ppm sodium hypochlorite solution. Carrots were sampled at 0, 7, and 14 days storage to determine microbial populations. Cilantro was similarly tested at 0, 6, and 12 days …

Design And Construction Of A Solar Operated Gate, Jacob Gardener

BioResource and Agricultural Engineering

This senior project discusses the design and construction of a solar operated gate. A solar panel is used to charge a battery, and then an inverter is used to run a garage door opener off the battery. The garage door opener operates a short lever arm which is connected to a longer lever arm which is connected to the gate. Each component and mounting mechanisms were designed and built to effectively provide the gate opening function. The finished product operates well, the gate opens in about 8 seconds after the button is pressed on the remote controller or wall mount …

Design, Acnd Construction Of A Portable Artificial Insemination Chute, Chris Herrera

BioResource and Agricultural Engineering

This senior project report discusses the design, construction, and evaluation of a portable artificial insemination chute for the use of the Cal Poly Beef Department. The design was based on the suggested modifications from operators of several other chutes currently in use.

The main areas considered for the design were; Ergonomics, cattle safety, factors effecting maximum breeding conception rates, and Portability.

The breeding chute proved superior over traditional chutes in a variety of ways. Improvement occurred in the areas of consideration as follows, user operation was simplified, animal stress was decreased, and maximum breeding efficiency was obtained.

On-Farm Irrigation Tracking Software For The Imperial Valley, Taylor Andrew Brady

BioResource and Agricultural Engineering

In order to improve on farm irrigation, a water scheduling program specific to the needs of Imperial Valley farmers will be created. The program will help keep track of daily water schedules, as well as stay connected with the farm personnel to reduce error and save time. The program will help with on farm operations and productivity by allowing the famer, irrigation foremen, and secretary to view the same schedule simultaneously. The information that is inputted into the program will be editable by all the chosen personnel, to keep everyone on the same page. Weekly, monthly, or yearly usage reports …

Expansion Of A Dust Removal System For The Brae Department Plasma Table, Derek Hansen

BioResource and Agricultural Engineering

This senior project discusses the expansion of a dust removal system for welding and cutting fumes. A Donaldson Torit Powercore TG8 dust collector is used to collect and process the fumes created during welding and cutting operations that take place in the BioResource and Agricultural Engineering department at Cal Poly San Luis Obispo. Expansion of the system allows for greatly increased utilization of the TG8 and a cleaner working environment in Lab #6. Testing shows that the system fluently changes between the plasma table and the three hoods in the shop. Each hood is only capable of collecting a smoke …

Comparison Of Field Level And Regional Actual Etc Values Developed From Remote Sensing And Dual Crop Coefficient Procedure, Daniel J. Howes, Lucas Hoffmann, Franklin Gaudi

BioResource and Agricultural Engineering

Crop evapotranspiration (ETc) estimates are important for regional water planning as well as irrigation scheduling. Traditional ETc computations utilize published crop coefficients (basal) that are adjusted on a daily basis depending on soil water availability (i.e., dual crop coefficient method). Recent advancements include using remote sensing data such as LandSAT combined with a surface energy balance algorithm (METRIC), allowing crop evapotranspiration to be computed for each pixel throughout images taken during the season. There are limitations and advantages for both methods. Comparisons of soil water balance evapotranspiration values to METRIC values for two scenarios in different regions of California have …

Basin-Wide Remote Sensing Of Actual Evapotranspiration And Its Influence On Regional Water Resources Planning, Daniel J. Howes, Charles M. Burt, Kyle Feist

BioResource and Agricultural Engineering

The Irrigation Training & Research Center (ITRC) at Cal Poly State University, San Luis Obispo has been using METRIC to compute actual evapotranspiration from remote sensing sources (namely LandSAT images). The driving force behind this is the increasing need for improved evapotranspiration information on a large scale. A recent study in the Mexicali Valley of Baja California, Mexico utilized the ITRC-modified METRIC procedure to compute the crop and riparian evapotranspiration component of a basin-wide water balance. The resulting comparison between the mass balance computed change in groundwater storage and that computed using groundwater elevation data showed excellent agreement. For water …

Pump Performance With Sand Wear, Charles M. Burt, Kyle Fesit

BioResource and Agricultural Engineering

In many installations, pump performance declines over time due to sand wear. In order to pinpoint the type and rate of wear caused by pumping water with higher-than-average sand concentrations and its direct effect on various pump impeller materials, vertical pump impeller/bowl assemblies of approximately 900 GPM were each pumped for up to 2500 hours with high concentrations of sand in the water. Two different impeller materials were used for a total of five configurations. Well pump operation was simulated by maintaining a constant discharge pressure. The degrading performance, in terms of changing flow rate and kilowatt load, was recorded …

Spatial Variability In Evapotranspiration Related To Irrigation System Distribution Uniformity, Daniel J. Howes, Lucas Hoffmann, Franklin Gaudi

BioResource and Agricultural Engineering

Understanding the causes of variable ET in a field is critical for maximizing yield on a per-acre basis as well as for proper irrigation scheduling and regional water management. Since 2004, the ITRC has provided technical irrigation support and management for over 2,000 acres of center pivot irrigated forage crops being supplied by reclaimed water near Palmdale, California. Irrigation scheduling is conducted using a daily soil water balance dual crop coefficient approach. Detailed records on planting and harvest dates, daily water applications, pivot run speeds, and annual distribution uniformity evaluations are maintained along with daily reference evapotranspiration data from a …

Irrigation Engineering In Seismic Zones - Mexicali Valley, Mexico, Alan Dennis Gracia, Charles M. Burt, Mario Paredes Vallejo

BioResource and Agricultural Engineering

On April 4, 2010 an earthquake of Richter magnitude 7.2 occurred with an epicenter south of Mexicali within the irrigated zone of Mexicali Valley. Extensive damage occurred to main and lateral canal structures, plus to field irrigation systems and the main drainage network. This paper describes the engineering for a new major irrigation water conveyance system to service the most heavily impacted zone of 80,000 acres. Considerations included identification of the causes of the damage, selection of canal versus pipeline, relocation costs of people along new routes, and improved flexibility of water delivery. Major investigations regarding soils, topography, etc. were …

Velocity Contour Weighting Method. Ii: Evaluation In Trapezoidal Channels And Roughness Sensitivity, Daniel Howes, Brett F. Sanders

BioResource and Agricultural Engineering

The Velocity Contour Weighting Method (VCWM) was developed in Part I to accurately estimate the cross-sectional average velocity of a prismatic channel flow using acoustic Doppler velocity meter (ADVM) measurements of centerline velocity. Here, the VCWM is validated by its successful application to 25 different concrete-lined trapezoidal channels used for irrigation water delivery. At each site, the cross-sectional distribution of velocity is measured by an acoustic Doppler velocimeter (ADV), which is moved horizontally and vertically through a sampling grid. Multiple tests at some sites led to a total of 51 sets of cross-sectional measurements. ADVM measurements are simulated by interpolating …

Velocity Contour Weighting Method. I: Algorithm Development And Laboratory Testing, Daniel J. Howes, Brett F. Sanders

BioResource and Agricultural Engineering

An algorithm is developed for real-time estimation of the cross-sectional average velocity of a channel flow by using an upward-looking pulsed wave acoustic Doppler velocity meters (ADVM). The Velocity Contour Weighting Method (VCWM) is applicable to gradually varied flows in prismatic channels and requires little to no calibration. VCWM estimates the average velocity as a weighted average of ADVM bin velocities. Weights are based on the velocity distribution sampled by the ADVM. Collectively, the VCWM is able to adapt to a wide range of channel geometry and roughness features. Expressions for the velocity weights are developed by first applying a …

Agricultural Irrigation Using Municipal Effluent, Charles M. Burt

BioResource and Agricultural Engineering

The paper describes the development of a design and management plan for disposing of secondary effluent originating in the urban communities. It highlights the differences in approach that a public utility must take, versus a typical agricultural irrigation application. Costs and requirements for municipal effluent irrigation are many times greater. The complexity of regulations and agency procurement procedures relegates the actual irrigation system design to a relatively small role in the total project.

The Irrigation Sector Shift From Construction To Modernization: What Is Required For Success?, Charles M. Burt

BioResource and Agricultural Engineering

External pressures related to environmental protection, commodity prices, energy availability, larger populations, and climate change have combined to require an immediate and substantial improvement in agricultural irrigation performance. Worldwide progression towards modernized irrigation projects has been uneven and slower than desired, but decades of irrigation modernization development have clarified certain requirements for success, as well as illuminated indicators of project failure. Of particular importance are required shifts within the state and national irrigation bureaucracies, as well as universities.

Effects Of Sprinkler, Partial Sprinkler/Drip, And Drip Only Irrigation On Strawberry Transplants 2010-2011, Stuart Styles

BioResource and Agricultural Engineering

The purpose of the project is to develop an analysis of the current irrigation practices of the strawberry growers on the Central Coast of California. The primary research evaluation is during the establishment of transplants where sprinklers are typically used even though drip irrigation is available. Growers have been selected from Oxnard, Santa Maria, and Watsonville to provide a good cross section of the different strawberry growing areas.

The specific objectives of the project are to: (1) set up a research areas and control plots on a demonstration scale, (2) determine the key factors that affect the problems in early …