Bioresource and Agricultural Engineering Commons^™

Hydrologic Properties Of Pervious Concrete, Joe D. Luck, Stephen R. Workman, Stephen F. Higgins, Mark S. Coyne

Plant and Soil Sciences Faculty Publications

Pervious concrete is concrete made by eliminating most or all of the fine aggregate (sand) in the concrete mix, which allows interconnected void spaces to be formed in the hardened product. These interconnected void spaces allow the concrete to transmit water at relatively high rates. The main objective of this project was to conduct research on the potential application of pervious concrete in agricultural settings, specifically for use in animal feed lots, manure storage pads, animal manure and bedding compost facilities, or floor systems in animal buildings. Laboratory tests were conducted on replicated samples of pervious concrete formed from two …

Development And Testing Of A Low-Cost Condensation Detection System, Michael D. Montross, George A. Duncan, Richard S. Gates

Biosystems and Agricultural Engineering Faculty Publications

A condensation sensing and control system was designed to detect condensation using a commercially available leaf wetness sensor (LWS). The leaf wetness sensor was a variable resistance grid-type that responded to moisture on the surface. A circuit was developed to compare the LWS voltage output to a user specified reference voltage, and operate a relay for possible switching of a humidity control device (for example a fan and/or heater). The condensation detection system operation was validated in an environmental chamber in the laboratory using a heat exchanger and water bath. Condensate was immediately detected when the plate was cooled below …

The Land Is In Your Hands : A Practical Guide For Owners Of Small Rural Landholdings In Western Australia, Department Of Agriculture And Food, Wa

Bulletins 4000 -

This Bulletin discusses various aspects of managing a small farm or property in Western Australia, including soil and land care, vegetation and plant control on farm holdings, water resource management, biosecurity, plant, animal and insect pest control and livestock management.

Desulfovibrio Desulfuricans G20 Tetraheme Cytochrome Structure At 1.5 A˚ And Cytochrome Interaction With Metal Complexes, Mrunalini Pattarkine, J J. Tanner, C A. Bottoms, Y H. Lee, Judy D. Wall

Faculty Works

The structure of the type I tetraheme cytochrome c3 from Desulfovibrio desulfuricans G20 was determined to 1.5 A˚ by X-ray crystallography. In addition to the oxidized form, the structure of the molybdate-bound form of the protein was determined from oxidized crystals soaked in sodium molybdate. Only small structural shifts were obtained with metal binding, consistent with the remarkable structural stability of this protein. In vitro experiments with pure cytochrome showed that molybdate could oxidize the reduced cytochrome, although not as rapidly as U(VI) present as uranyl acetate. Alterations in the overall conformation and thermostability of the metal-oxidized protein were investigated …

Simulated Performances Of A Heat Pump System For Energy And Water Conservation In Open And Confined Greenhouse Systems, Ilhami Yildiz, D. P. Stombaugh

BioResource and Agricultural Engineering

The purpose of this study was to determine and compare the performances of conventional and heat pump systems for energy and water conservation in open and confined greenhouse systems. Conventional gas furnaces and evaporative cooling, respectively, provided heating and cooling in the conventional system. In the heat pump systems, gas-fired heat pump units provided both heating and cooling. The greenhouse with heat pump units also had an option to be operated as a completely confined system, using one of the heat pump units as a dehumidifier. Average energy consumption in winter was 56.9, 23.5, and 11.3 MJ/day.m² in the conventional, …

Trees And Ice Storms: The Development Of Ice Storm–Resistant Urban Tree Populations (Second Edition), Richard J. Hauer, Jeffrey O. Dawson, Les P. Werner

United States Department of Agriculture, Forest Service / University of Nebraska-Lincoln: Faculty Publications

Severe ice storms occur every year in the United States and Canada, particularly in the midwestern and eastern regions of the United States. Along with fires and wind, ice storms are a frequent and major natural disturbance factor in eastern deciduous forests. Likewise ice storms are responsible for deaths and injuries of people and cause dramatic damage and tree loss to urban forests. Ice storms annually result in millions of dollars in loss, and potentially billions of dollars in losses for extreme and widespread ice storms. Damage to electric distribution systems, blocked roadways, and property damage from fallen trees and …

Dynamic Modeling Of Microclimate And Environmental Control Strategies In A Greenhouse Coupled With A Heat Pump System, Ilhami Yildiz, D. P. Stombaugh

BioResource and Agricultural Engineering

The purpose of this study was to develop and validate a dynamic simulation model to be employed in accurate prediction of microclimate in a greenhouse as a function of dynamic environmental factors. The model has options to evaluate the effects of location, time of the year, orientation, single and double polyethylene glazings, conventional and heat pump heating and cooling systems, open and confined greenhouse systems, CO₂ enrichment, variable shading, and the use of night curtains. Conventional gas furnace and evaporative cooling, respectively, provided heating and cooling in the conventional system. In the heat pump systems, gas-fired heat pump units …

Vertical Loads Due To Wheat On Obstructions Located On The Floor Of A Model Bin, Marek Molenda, Michael D. Montross, Sidney A. Thompson, Jozef Horabik

Biosystems and Agricultural Engineering Faculty Publications

Tests were conducted in a model grain bin to evaluate the vertical loads acting on differently shaped obstructions embedded in wheat during filling, detention, and discharge. The bin had corrugated galvanized steel walls with a 1.83 m diameter and a flat bottom. All tests were conducted in a bin that was centrically loaded and unloaded. Three differently shaped obstructions (disc, cone, and cylinder) were tested; each had a circular base equivalent to 6% of the bin floor area. The obstructions were supported in the bin using a three-legged support structure. Each leg of the support structure rested on a load …

Air Exchange Rate In A Horse Trailer During Road Transport, Joseph L. Purswell, Richard S. Gates, Laurie M. Lawrence, Jamey D. Jacob, Timothy S. Stombaugh, Robert J. Coleman

Biosystems and Agricultural Engineering Faculty Publications

Horses traveling by road commonly experience heat stress conditions and poor air quality, which may be caused by insufficient ventilation; however, there are few estimates of air exchange in a horse trailer during transport. Air exchange rate was measured at ten locations within a four-horse trailer (internal volume 18.5 m³) using tracer gas decay measurement to assess the adequacy of ventilation. Three vehicle speeds (13, 48, and 97 km h^-1) and three window configurations (all windows and roof vents closed, all windows open, all windows open and roof vents open forward) were tested with and without …

Distribution Pattern Variability Of Granular Vrt Applicators, John P. Fulton, Scott A. Shearer, Stephen F. Higgins, Dennis Wayne Hancock, Timothy S. Stombaugh

Biosystems and Agricultural Engineering Faculty Publications

Granular applicators equipped with variable-rate technology (VRT) have gained popularity in recent years as a result of increased interest in variable-rate application. The purpose of this investigation was to characterize distribution patterns at varying rates for different granular applicators. Uniform-rate (UR) tests were conducted to assess the accuracy of variable-rate application from four granular applicators: two spinner-disc spreaders (A and B), and two pneumatic applicators (C and D). Pattern results indicated a consistent triangular pattern for spinner spreader B and consistent patterns for the pneumatic applicators (C and D). However, applicator D produced pattern variations at the center and right …

Rate Response Assessment From Various Granular Vrt Applicators, John P. Fulton, Scott A. Shearer, Stephen F. Higgins, Matthew J. Darr, Timothy S. Stombaugh

Biosystems and Agricultural Engineering Faculty Publications

Variable-rate technology (VRT) adds complexity to application equipment, thereby confounding the assessment of applicator performance. The intent of this investigation was to assess the rate response of various VRT granular applicators: two spinner spreaders (A and B), and two pneumatic applicators (C and D). Variable-rate (VR) tests were conducted to quantify the rate response characteristics (delay and transition times) for the applicators. A sigmoidal function was used to model the rate response for five of the six tests. Applicator A exhibited a linear response during decreasing rate changes. Results indicated that only applicator B demonstrated consistent delay and transition times, …

Spatial Variation Of Protein, Oil, And Starch In Corn, Samuel G. Mcneill, Michael D. Montross, Scott A. Shearer

Biosystems and Agricultural Engineering Faculty Publications

Significant spatial yield variations are known to exist in cornfields with different soil types, topsoil depth, and other variables. Similarly, variations might also be found among the highly valued chemical components (oil, protein, and starch) in corn kernels due to local differences in soil type, fertility, acidity/pH, organic matter, etc. This study quantified the spatial variability of protein, oil, and starch content of corn from two conventional cornfields and two high-oil cornfields. Whole ears were harvested by hand from 20 to 40 randomly selected locations within each field. A differential global positioning system (DGPS) receiver recorded the location of each …

Permeability Of Corn, Soybeans, And Soft Red And White Winter Wheat As Affected By Bulk Density, Michael D. Montross, Samuel G. Mcneill

Biosystems and Agricultural Engineering Faculty Publications

Darcy’s law is a function of viscosity, permeability, and velocity and can be used to predict the airflow resistance in granular materials at low air velocities. Permeability also governs the magnitude of natural convection currents during periods of non-aerated grain storage. The permeability of corn, soybeans, soft white winter wheat, and soft red winter wheat were measured as a function of bulk density and moisture content. Air was passed through a column of grain and the flow rate and pressure drop measured. Bulk density and kernel density were also measured to determine the porosity of grain in the test column. …

Airflow Resistance Of Seeds At Different Bulk Densities Using Ergun's Equation, Marek Molenda, Michael D. Montross, Samuel G. Mcneill, Jozef Horabik

Biosystems and Agricultural Engineering Faculty Publications

Airflow resistance of grains and oilseeds has been extensively studied. Traditionally the data has been presented using Shedd’s curves. However, this assumes that airflow resistance is independent of grain depth. Grain undergoes compaction during storage that changes the bulk density, porosity, and therefore the airflow resistance. Ergun’s equation is a function of particle size and porosity of the granular material. Airflow resistance by Ergun’s equation was used to predict the pressure drop across a column of corn, soft white winter wheat, soft red winter wheat, and soybeans at three moisture content levels and two bulk densities. The maximum root mean …

Crop Yield Response To Precision Deep Tillage, Larry G. Wells, Timothy S. Stombaugh, Scott A. Shearer

Biosystems and Agricultural Engineering Faculty Publications

Experimental precision deep tillage was applied at three sites in central Kentucky with relatively well-drained silt loam soils in no-till crop production. Fields were divided into 0.4 ha (1 ac) grid cells using DGPS mapping. Assessment of soil compaction by machinery traffic was made using multiple soil cone penetrometer measurements and expressed as cone index (CI). Corn, wheat, and soybean yields were depressed in grid cells with CI_avg ≥ 1.5 MPa (218 psi) prior to application of tillage treatments at sites 1 and 3, whereas at site 2, where most of the highest average CI values ranged from 1.44 …

Effect Of Fat And Casein Particles In Milk On The Scattering Of Elliptically Polarized Light, Czarena L. Crofcheck, Jeremie Wade, Janakiraman N. Swamy, Mustafa M. Aslan, M. Pinar Mengüç

Biosystems and Agricultural Engineering Faculty Publications

In this article, we present an experimental approach to determine the milk fat content using scattered light intensity profiles. The elements of the scattering (Mueller) matrix have been shown to provide valuable information about variation of the optical properties of scattering particles. The scattering behavior of fat and casein in terms of the scattering matrix elements was experimentally determined for milk with varying fat levels ranging from 0.05 wt% (skim) to 3.20 wt% (whole). Three of the scattering Mueller matrix elements, specifically S₁₁, S₁₂/S₁₁, and S₃₃/S₁₁, were found to be …

Controller Area Network Based Distributed Control For Autonomous Vehicles, Matthew J. Darr, Timothy S. Stombaugh, Scott A. Shearer

Biosystems and Agricultural Engineering Faculty Publications

The goal of this project was to evaluate the potential of a controller area network (CAN bus) to be used as the communication network for a distributed control system on an autonomous agricultural vehicle. The prototype system utilized microcontroller-driven nodes to act as control points along a CAN bus. Messages were transferred to the steering, transmission, and hitch control nodes via a task computer. The task computer utilized global positioning system data to generate appropriate control commands. Laboratory and field testing demonstrated that each of the control nodes could function simultaneously over the CAN bus. Results showed that the task …

Aeration Strategies And Fan Cost Comparisons For Wheat In Mid-South Production Regions, Thomas C. Bridges, Michael D. Montross, Samuel G. Mcneill

Biosystems and Agricultural Engineering Faculty Publications

Numerous factors influence the sizing of aeration fans for summer-harvested crops. Thirty years of weather data for Lexington, Kentucky, were analyzed and the cost of aeration was compared for two axial fans (afan1, afan2) and one centrifugal fan (cfan1). Aeration costs were defined as the sum of the following components: the cost of owning the fan, the cost of electricity for operating the fan, a cost for wheat shrinkage during aeration, and a cost for dry matter loss (DML). The fans were selected to deliver airflow rates of approximately one, two, and three times the recommended aeration rate of 0.11 …

Streambank Erosion Associated With Grazing Practices In The Humid Region, Carmen T. Agouridis, Dwayne R. Edwards, Stephen R. Workman, José R. Bicudo, Benjamin K. Koostra, Eric S. Vanzant, Joseph L. Taraba

Biosystems and Agricultural Engineering Faculty Publications

The effects of cattle grazing on stream stability have been well documented for the western portion of the U.S., but are lacking for the east. Stream and riparian damage resulting from grazing can include alterations in watershed hydrology, changes to stream morphology, soil compaction and erosion, destruction of vegetation, and water quality impairments. However, few studies have examined the successes of best management practices (BMPs) for mitigating these effects. The objective of this project was to assess the ability of two common BMPs to reduce streambank erosion along a central Kentucky stream. The project site consisted of two replications of …

Vertical Wall Loads In A Model Grain Bin With Non-Axial Internal Inserts, Marek Molenda, Michael D. Montross, Jozef Horabik, Sidney A. Thompson

Biosystems and Agricultural Engineering Faculty Publications

A study was conducted to estimate the degree of load asymmetry in a bin with non-axial internal inserts. Internal inserts in the form of an annulus segment were attached to the wall, and their influence on vertical wall loads during centric filling and discharge in a model bin were measured. Wall and floor loads were measured in a corrugated-wall model grain bin with a diameter of 2.44 m and a height of 7.3 m filled with soft red winter wheat to a depth of 6.7 m (height-to-diameter ratio of 2.75). Tests were conducted with inserts that extended circumferentially 30°, 60°, …

Seasonal Aeration Rates For The Eastern United States Based On Long-Term Weather Patterns, Michael D. Montross, Samuel G. Mcneill, Thomas C. Bridges

Biosystems and Agricultural Engineering Faculty Publications

Most aeration fans are sized to produce a minimum airflow rate of 0.1 m³/min/t (0.1 cfm/bu) in on-farm grain storage structures. At this airflow rate a significant amount of time is required to move a cooling front completely through a bin. The desired grain temperature and prevailing weather conditions will have a significant effect on required fan size. Thirty years of weather data were analyzed for the eastern United States to determine the amount of time available in temperature windows between 0 to 15.C and 0 to 17.C. Contour maps were generated with ArcMap 8.3 for the percentage …

Suitability Of A Gps Collar For Grazing Studies, Carmen T. Agouridis, Timothy S. Stombaugh, Stephen R. Workman, Benjamin K. Koostra, Dwayne R. Edwards, Eric S. Vanzant

Biosystems and Agricultural Engineering Faculty Publications

The traditional means of tracking animal location in a field is by visual observation. Not only is this method labor intensive, it is also prone to error as the observer can alter cattle movement, observation periods are often too short to obtain confidence in general daily behavior patterns, and observer fatigue becomes an issue. In the 1990s, the University of Kentucky began using GPS collars on cattle to track their position with the goal of incorporating this information into cattle management practices. One of the key unanswered questions regarding the GPS collars is the accuracy of the position data recorded …

Effect Of Moisture Content And Broken Kernels On The Bulk Density And Packing Of Corn, Samuel G. Mcneill, Sidney A. Thompson, Michael D. Montross

Biosystems and Agricultural Engineering Faculty Publications

Shelled yellow dent corn samples were conditioned to three moisture content levels (12%, 15%, and 18% w.b.) and mixed with a prescribed amount of broken corn particles of known size (geometric mean diameter of 1.0, 1.4, 2.0, 2.8, and 4.0 mm) and concentration (2.5%, 5.0%, and 7.5% by weight) levels. The initial bulk density and grain compaction under simulated overburden pressure tests were determined for each sample. Uniaxial compression tests were performed for seven vertical pressure levels (3.4, 6.9, 14, 28, 55, 110, and 165 kPa) with a minimum of three replications each. Tests were performed at two locations with …

The Influence Of Environmental Temperature And Substrate Initial Moisture Content On Aspergillus Niger Growth And Phytase Production In Solid−State Cultivation, Seaborn B. Carter, Sue E. Nokes, Czarena L. Crofcheck

Biosystems and Agricultural Engineering Faculty Publications

Aspergillus niger is being used commercially for phytase production utilizing solid-state cultivation; however, no studies have been published that investigated the optimal environmental temperature and initial substrate water content to maximize fungal growth and/or phytase production. Solid-state cultivations of Aspergillus niger on wheat bran and soybean meal were conducted at three temperatures (25°C, 30°C, and 35°C) and three initial moisture contents (50%, 55%, and 60% wet basis) in a split-plot full-factorial experimental design. Fermentations were conducted for 0, 24, 48, 72, and 120 h. The containers were sampled destructively and assayed for phytase activity and glucosamine concentration as an estimate …

Simulation Of Fixed– And Variable–Rate Application Of Granular Materials, John Patrick Fulton, Scott A. Shearer, Timothy S. Stombaugh, Michael E. Anderson, Thomas F. Burks, Stephen F. Higgins

Biosystems and Agricultural Engineering Faculty Publications

Research has shown that application errors exist with variable–rate technology (VRT) systems. Consequently, using prescription maps for economic and agronomic analyses can generate misleading results. The intent of this article was to develop and validate a spatial data model for generating “as–applied” maps to support the advancement of precision agriculture practices. Previous research modified ASAE Standard S341.2 to include a 2–D matrix of collection pans to assess fixed–rate and variable–rate (VR) deposition of granular fertilizers and agricultural lime from a spinner disc spreader. The “as–applied” spatial data model uses GIS functionality to generate “as–applied” surfaces by merging distribution patterns and …

Assessing The Benefits Of Misting–Cooling Systems For Growing/Finishing Swine As Affected By Environment And Pig Placement Date, Thomas C. Bridges, Larry W. Turner, Richard S. Gates, Douglas G. Overhults

Biosystems and Agricultural Engineering Faculty Publications

The NCPIG swine growth model was used to evaluate swine growth performance for Wilmington, North Carolina; Bardstown and Mayfield, Kentucky; and Oklahoma City, Oklahoma as influenced by the use of a misting–cooling system. Five pig placement dates (Julian days 106, 126, 146, 166, and 186) were evaluated for each location using 22 years of weather data (1978–1999). The use of a misting system, while quite variable, was found to be generally profitable, reducing the length of the time to reach market weight. As the placement date increased, the average return to misting ($/pig/year) decreased from $8.12 to $1.98 for Oklahoma …

Dam Design For Pastoral Stock Water Supplies, J S. Addison, R J. Law, G B. Eliot

Bulletins 4000 -

These notes provide information on many components of water harvesting storage systems designed for use in semi-arid areas. The notion of a water harvesting and storage system is deliberately emphasised. No single design component can be considered in isolation if the goal of a drought-proof water supply is to be achieved.

A drought-proof surface water supply is achieved by integrating the many design components of a water harvesting/storage system into a practical plan.

Pc–Based Data Acquisition For A Solid Substrate Cultivation Deep Bed Reactor, Mari S. Chinn, Sue E. Nokes, Richard S. Gates

Biosystems and Agricultural Engineering Faculty Publications

This work describes an instrumentation and data acquisition system designed for a deep bed reactor used to cultivate Trichoderma longibrachiatum on wheat bran. The system allowed on–line measurements of substrate temperature, oxygen concentration within the reactor headspace, relative humidity and temperature of the inlet air, and inlet airflow rates while maintaining aseptic conditions and without disturbing the cultivation process. An error analysis for the instrumentation and data acquisition equipment was completed and provided insight into the reliability of the sensor readings. The collected data provided quantitative information about the reactor system dynamics which can be used to evaluate and apply …

Recommended Strategies For Odor Control In Confinement Beef Cattle Operations, Kent Tjardes, Alvaro Garcia, Hans Stein, Charles Ullery, Stephen Pohl, Christopher Schmit

SDSU Extension Special Series

Odors coming off a beef feeding operation are generated from three different sources: the feedlot facility, waste storage, and the land where the manure is applied. In some operations, the feedlot facility may also serve as the primary waste storage area. To reduce the total amount of odor generated from a beef feeding operation, odor generation and emission by each of these three sources needs to be reduced.

Mechanical Properties Of Corn And Soybean Meal, Marek Molenda, Michael D. Montross, Jozef Horabik, Ira Joseph Ross

Biosystems and Agricultural Engineering Faculty Publications

Ground corn and soybean meal are common ingredients in feed mixes. The knowledge of their mechanical properties is important to the feed manufacturer and consumer. Changes in these properties can lead to abnormally high or low levels of active ingredients in finished feed, thus decreasing its quality. Mechanical properties of wheat, corn meal, and soybean meal were investigated using a modified direct shear apparatus. The moisture content (wet basis), uncompacted bulk density, and particle density were: 10.4%, 733 kg/m³, and 1410 kg/m³ for soft red winter wheat; 11.4%, 583 kg/m³, and 1350 kg/m³ for …