Biomedical Devices and Instrumentation Commons^™

Micro Electrostatic Actuation Of A Silicon Diaphragm, Matthew W. Samples

Master's Theses

There are a number of applications, from hearing aids to microfluidic pumps, which utilize micro-scale actuating diaphragms. These MEMS (micro-electromechanical system) devices can be actuated by electrostatic forces, which utilize an induced electric field to pull two charged plates towards one another. Such devices were fabricated and electrostatic actuation of the diaphragms was performed to analyze its viability as a micro-speaker. The long-term performance of such products requires adequate diaphragm deflection to create audible pressure waves with relatively low maximum stresses to ensure a high cycle fatigue life. With these requirements, initial calculations and FEA (finite element analysis) were performed …

Analysis Of Particles Thorough The Aortic Arch During Transcatheter Aortic Valve Replacement, Andrew Joseph Janicki

Master's Theses

Ischemia caused by particles becoming dislodged during transcatheter aortic valve replacement (TAVR) is a possible complication of TAVR. The particles that become dislodged can travel out of the aortic valve, into the aortic arch, and then into either the brachiocephalic artery, the left common carotid artery, the left subclavian artery or continue into the descending aorta. If the particles continue into the descending aorta it poses no risk of causing ischemia however if it travels into the other arteries then it increases the possibility of the particle causing an ischemic event. The goal of this study is to determine what …

Design And Fabrication Techniques Of Devices For Embedded Power Active Contact Lens, Errol Heradio Leon

Master's Theses

This thesis designed and fabricated various devices that were interfaced to an IC for an active contact lens that notifies the user of an event by detection of an external wireless signal. The contact lens consisted of an embedded antenna providing communication with a 2.4GHz system, as well as inductive charging at an operating frequency of 13.56 MHz. The lens utilized a CBC005 5µAh thin film battery by Cymbet and a manufactured graphene super capacitor as a power source. The custom integrated circuit (IC) was designed using the On Semiconductor CMOS C5 0.6 µm process to manage …

Sapien3 Comb Stitch Improvement For Edwards Lifesciences, William Harley, Thomas Pluschkell, John Mctigue, Garrett Reed

Mechanical Engineering

The complete senior project report was submitted to the project advisor and sponsor. The results of this project are of a confidential nature and will not be published at this time.

A Comprehensive Review Of The Food And Drug Administration, The 510(K) Application Process, And Fda Certification For A Diagnostic Device, Taylor Davis

Biomedical Engineering

The company G-Force CRC LLC is currently experiencing the dichotomy of the FDA's conflicting role right now as they begin to approach FDA approval. G-Force CRC LLC is a small medical device company headquartered in San Diego, CA. The owner of the company, Dr. Ian Purcell, is an Otoneurologist apart of Alvarado Hospital. His medical practice mainly deals with patients who have balance disorders and therefore the devices that he has developed over the last 6+ years are primarily used to assist in the diagnosis of those balance disorders. G-Force CRC LLC was officially created in the summer of 2013 …

Renal Artery Stent Fatigue Test, Braden Cooper, Munir Eltal, Jennifer Hawthorne, Ashley Schaefer

Mechanical Engineering

In today’s world of medical innovation, regulations and requirements set by organizations such as the Food and Drug Administration (FDA), the International Organization for Standardization (ISO), and ASTM International (American Society for Testing and Materials) can inhibit rapid innovation by demanding rigorous testing of new designs. For arterial stents, the standard is that each design must be tested to simulate 10 years of life in an environment congruent to an in vivo environment. Endologix in Irvine, California develops and manufactures minimally invasive treatments for aortic diseases, with a focus on stent grafts for the treatment of abdominal aortic aneurysms (AAA). …

Heart Valve Leaflet Deflection Testing Apparatus, Brandon Cunnane, Andrew Krasts, Jackson Kunz, Steven Warnert

Mechanical Engineering

The information contained in this report is confidential and proprietary information of Edwards Lifesciences.

Self-Contained Breathing Apparatus For Firefighter With A Permanent Stoma, Jason Delgadillo, Aaron Wheeler, Zachary Wishbow

Biomedical Engineering

The purpose of this project was to create a unique SCBA (self-contained breathing apparatus) for a firefighter named Chris Gauer. This prototype consists of a SCBA headgear connected to a polycarbonate-formed stoma mask with a medical-grade sanitary silicone hose.

Method And Apparatus For Treating Centralized Pain, Jeffrey Hargrove

Mechanical Engineering Patents

A method for alleviating centralized pain in human subjects includes assessing the brain of a subject suffering from pain, diagnosing abnormal brain function associated with centralized pain, locating at least one area of abnormal brain function associated with the centralized pain, and alleviating the abnormal brain function by applying a cortical stimulation signal to tissues corresponding to the at least one area of abnormal brain function.

3d Printing In Healthcare, Caleb Branch

The Review: A Journal of Undergraduate Student Research

Technology is everywhere. Technology surrounds every aspect of 21^st century life. It is in the cell phones we use, the cars we drive, and even the food we eat. A large portion of modern technology used is taken for granted and overlooked. Despite this, some technology fields continue to grow. Biomedical engineering, specifically 3D printing’s applications to healthcare, has been often overlooked until. Regardless of its status in the mainstream, 3D printing is prosperous in healthcare and its future looks bright. This piece analyzes 3D printing in healthcare. It hones in on the finer details of each specific topic, …

Mobile Health Sensing With Smart Phones, Abby Logan Wise

Electrical Engineering Undergraduate Honors Theses

Depression is a serious mental condition affecting many Americans and people across the world. Postpartum depression is a form of depression affecting women who have recently gone through childbirth. Postpartum depression can have serious symptoms that may affect not only the mother, but her newborn as well. Early detection of these symptoms is of critical importance to the welfare of the mother and her child. Many medical professionals express the need for postpartum screening being that treatment has proven to be very effective. This project aims to make early symptom detection convenient and reliable for mothers with newborns. This will …

Design And Development Of Two Component Hydrogel Ejector For Three-Dimensional Cell Growth, Thomas Dunkle, Jessica Deschamps, Connie Dam

Honors Scholar Theses

Hydrogels are useful in wound healing, drug delivery, and tissue engineering applications, but the available methods of injecting them quickly and noninvasively are limited. The medical industry does not yet have access to an all-purpose device that can quickly synthesize hydrogels of different shapes and sizes. Many synthesis procedures that have been developed result in the formation of amorphous hydrogels. While generally useful, amorphous hydrogels exhibit limited capability in tissue engineering applications, especially due to their viscous properties. This endeavor aims to modulate the appropriate gelation parameters, optimize the injection process, and create a prototype that allows for the extrusion …

Hand Pattern Recognition Using Smart Band, Theerth Raj Munusamy

Graduate Theses and Dissertations

The Importance of gesture recognition has widely spread around the world. Many research strategies have been proposed to study and recognize gestures, especially facial and hand gestures. Distinguishing and recognizing hand gestures is vital in hotspot fields such as bionic parts, powered exoskeleton, diagnosing muscle disorders, etc. Recognizing such gesture patterns can also create a stress-free and fancy user interface for mobile phones, gaming consoles and other such devices.

The objective is to design a simple yet efficient wearable hand gesture recognizing system. This thesis also shows that by taking both EMG and accelerometer data into account, can improve the …

Evaluating The Effectiveness Of Cranial Molding For Treatment Of Positional Plagiocephaly Using Finite Element Analysis, Maziyar Keshtgar

Master's Theses

Since the advent of recommendations for placing infants in the supine position during sleep to reduce the incidence of sudden infant death syndrome, clinicians have noted an increase in the frequency of cranial asymmetry due to deformation of suture sections of the infants’ skulls as a result of constant concentrated stress in one area at the back of their head. This specific form of cranial deformation is known as positional plagiocephaly and its rate of occurrence has increased from 0.3% in 8.2% within the past 30 years.

Current treatments and methodologies for preventing and correcting positional plagiocephaly such as stretching …

Software Tools And Analysis Methods For The Use Of Electromagnetic Articulography Data In Speech Research, Andrew Kolb

Master's Theses (2009 -)

Recent work with Electromagnetic Articulography (EMA) has shown it to be an excellent tool for characterizing speech kinematics. By tracking the position and orientation of sensors placed on the jaws, lips, teeth and tongue as they move in an electromagnetic field, information about movement and coordination of the articulators can be obtained with great time resolution. This technique has far-reaching applications for advancing fields related to speech articulation, including recognition, synthesis, motor learning, and clinical assessments. As more EMA data becomes widely available, a growing need exists for software that performs basic processing and analysis functions. The objective of this …

Adjustable Jig And Method For Targeting Interlocking Holes Of An Intramedullary Nail, Patrick Atkinson, Adam Nicholas Garlock

Mechanical Engineering Patents

A targeting jig apparatus for targeting interlocking holes of an intramedullary nail. The targeting jig includes a support-arm extending substantially parallel to the intramedullary nail. A targeting mechanism including a pair of targeting mechanism drill-guide orifices is adjustably disposed on the support arm for aligning the targeting mechanism drill-guide orifice with the interlocking holes of the intramedullary nail. The targeting mechanism includes a saddle having a U-shape including a base and parallel legs that are slidable along the support-arm. A connection mechanism includes a horizontal slot on the support-arm aligned with a vertical slot on the targeting mechanism and a …

Fabrication And Characterization Of Poly(Octanediol Citrate)/Gallium-Containing Bioglass Microcomposite Scaffolds, Ehsan Zeimaran, Sara Pourshahrestani, Belinda Pingguan-Murphy, Nahrizul Adib Kadri, Hussin A. Rothan, Rohana Yusof, Mark R. Towler, Ivan Djordjevic

Chemical and Biochemical Engineering Faculty Research & Creative Works

Bone can be affected by osteosarcomae requiring surgical excision of the tumor as part of the treatment regime. Complete removal of cancerous cells is difficult and conventionally requires the removal of a margin of safety around the tumor to offer improved patient prognosis. This work considers a novel series of composite scaffolds based on poly (octanediol citrate) (POC) impregnated with gallium-based bioglass microparticles for possible incorporation into bone following tumor removal. The objective of this research was to fabricate and characterize these scaffolds and subsequently report on their mechanical and biological properties. The porous micro composite scaffolds with various concentrations …

A Glass Polyalkenoate Cement Carrier For Bone Morphogenetic Proteins, Adel M.F. Alhalawani, Omar Rodriguez, Declan J. Curran, Russell Co, Sean Kieran, Saad Arshad, Timothy J. Keenan, Anthony W. Wren, Gazelle Crasto, Sean A.F. Peel, Mark R. Towler

Chemical and Biochemical Engineering Faculty Research & Creative Works

This work considers a glass polyalkenoate cement (GPC)-based carrier for the effective delivery of bone morphogenetic proteins (BMPs) at an implantation site. A 0.12 CaO–0.04 SrO–0.36 ZnO–0.48 SiO₂ based glass and poly(acrylic acid) (PAA, Mw 213,000) were employed for the fabrication of the GPC. The media used for the water source in the GPC reaction was altered to produce a series of GPCs. The GPC liquid media was either 100 % distilled water with additions of albumin at 0, 2, 5 and 8 wt% of the glass content, 100 % formulation buffer (IFB), and 100 % BMP (150 µg …

Person Identification From Streaming Surveillance Video Using Mid-Level Features From Joint Action-Pose Distribution, Binu M. Nair, Vijayan K. Asari

Electrical and Computer Engineering Faculty Publications

We propose a real time person identification algorithm for surveillance based scenarios from low-resolution streaming video, based on mid-level features extracted from the joint distribution of various types of human actions and human poses.

The proposed algorithm uses the combination of an auto-encoder based action association framework which produces per-frame probability estimates of the action being performed, and a pose recognition framework which gives per-frame body part locations.

The main focus in this manuscript is to effectively combine these per-frame action probability estimates and pose trajectories from a short temporal window to obtain mid-level features. We demonstrate that these mid-level …

Investigating The Solubility And Cytocompatibility Of Cao-Na2o-Sio2/Tio2 Bioactive Glasses, Anthony W. Wren, Aisling Coughlan, Courtney M. Smith, Sarah P. Hudson, Fathima R. Laffir, Mark R. Towler

Chemical and Biochemical Engineering Faculty Research & Creative Works

This study aims to investigate the solubility of a series of titanium (TiO₂)-containing bioactive glasses and their subsequent effect on cell viability. Five glasses were synthesized in the composition range SiO₂-Na₂O-CaO with 5 mol % of increments TiO₂ substituted for SiO₂. Glass solubility was investigated with respect to (1) exposed surface area, (2) particle size, (3) incubation time, and (4) compositional effects. Ion release profiles showed that sodium (Na⁺) presented high release rates after 1 day and were unchanged between 7 and 14 days. Calcium (Ca²⁺) release …

Development And Validation Of A Robust, Adjustable Hippotherapy Simulator, Melissa Montgomery

Graduate Theses - Biology & Biomedical Engineering

This thesis describes all aspects of development, testing, refinement, and validation of a robust, adjustable hippotherapy simulator. This simulator primarily focuses on physical therapy; however, emotional benefits can be realized. It uniquely innovates on an effective design that has only partially been addressed in other simulators. Using a variable drive for adjustable speed, it incorporates reinforcements to increase load capacity along with removable camshafts that adjust the throw heights in the device’s simulated hips and shoulders. For testing and validation, Qualisys software and motion capture supported analysis of the device’s motion paths and speeds. Riders weighing approximately 135-300 pounds successfully …

Collagen Crosslinking Reagent Utilized To Modify The Mechanical Properties Of The Soft Palate In Equine Snoring And Apnea Applications, Stephanie L. Hunt

Theses and Dissertations--Biomedical Engineering

Snoring is a sleep disruption that can lead to obstructive sleep apnea (OSA), which interrupts breathing by obstructing the airway. Injecting a protein crosslinker, such as genipin, into the soft palate could decrease the severity of snoring and OSA by stiffening the soft palate. Equine soft palates modeled human palates due to a high incidence of awake snoring and apnea.

The pilot in vivo study treated six horses with two 100 mM injections of the buffered genipin reagent. The efficacy phase horses underwent respiratory audio recordings to document snoring changes using Matlab and ImageJ in the time and frequency domains. …

Noncontact Diffuse Correlation Tomography Of Breast Tumor, Lian He

Theses and Dissertations--Biomedical Engineering

Since aggressive cancers are frequently hypermetabolic with angiogenic vessels, quantification of blood flow (BF) can be vital for cancer diagnosis. Our laboratory has developed a noncontact diffuse correlation tomography (ncDCT) system for 3-D imaging of BF distribution in deep tissues (up to centimeters). The ncDCT system employs two sets of optical lenses to project source and detector fibers respectively onto the tissue surface, and applies finite element framework to model light transportation in complex tissue geometries. This thesis reports our first step to adapt the ncDCT system for 3-D imaging of BF contrasts in human breast tumors. A commercial 3-D …

Diffuse Optical Measurements Of Head And Neck Tumor Hemodynamics For Early Prediction Of Chemo-Radiation Therapy Outcomes, Lixin Dong

Theses and Dissertations--Biomedical Engineering

Chemo-radiation therapy is a principal modality for the treatment of head and neck cancers, and its efficacy depends on the interaction of tumor oxygen with free radicals. In this study, we adopted a novel hybrid diffuse optical instrument combining a commercial frequency-domain tissue oximeter (Imagent) and a custom-made diffuse correlation spectroscopy (DCS) flowmeter, which allowed for simultaneous measurements of tumor blood flow and blood oxygenation. Using this hybrid instrument we continually measured tumor hemodynamic responses to chemo-radiation therapy over the treatment period of 7 weeks. We also explored monitoring dynamic tumor hemodynamic changes during radiation delivery. Blood flow data analysis …

Effect Of Nitrogen On Properties Of Na2o-Cao-Sro-Zno-Sio2 Glasses, Ahmed Bachar, Cyrille Mercier, Arnaud Tricoteaux, Jean Christophe Hornez, Anne Leriche, Claudine Follet, Bertrand Revel, Stuart Hampshire, Mark R. Towler

Chemical and Biochemical Engineering Faculty Research & Creative Works

Glasses in the Na₂O-CaO-SrO-ZnO-SiO₂ system have previously been investigated for suitability as a reagent in Al-free glass polyalkenoate cements (GPCs). These materials have many properties that offer potential in orthopedics. However, their applicability has been limited, to date, because of their poor strength. This study was undertaken with the aim of increasing the mechanical properties of a series of these Zn-based GPC glasses by doping with nitrogen to give overall compositions of: 10Na₂O-10CaO-20SrO-20ZnO-(40-3x)SiO₂-xSi₃N₄ (x is the no. of moles of Si₃N₄). The density, glass-transition temperature, hardness, …

Nasa Limited Inflight Lab Sensor, Gregory P. Howard, James C. Hanreck

Williams Honors College, Honors Research Projects

The National Aeronautics and Space Administration (NASA) is currently developing the capabilities needed to send humans to Mars in 2030 for a three year mission. Astronaut health must be monitored monthly during such a lengthy mission. The UA Enterprise Senior Design Team worked to design a reusable, novel blood panel cartridge system to monitor astronaut health and to minimize waste production. Most current cartridges are composed of polydimethylsiloxane (PDMS). PDMS microchannels were fabricated to conduct simple proof of concept experiments for the design of a novel cartridge. To determine an ideal blood cleaning solution, bovine blood will be injected into …

Foley Catheter Priming Device, Melissa A. Boswell, Landon Davis, Renee Horn, Tyler Grubb, Jason Green

Williams Honors College, Honors Research Projects

A lack of a pressure gradient throughout the catheter prevents urine flow from the bladder and through catheter system in a condition referred to as “air-lock.” The purpose of this project was to design a device that could be utilized by person with a catheter faced with the problem of air-lock to restore urine flow and normal functioning of the catheter system. After a prototype was created, the device was put through a series of tests to insure proper functioning, absence of leakage, and durability. The device created can be added in-line with the catheter system, inconspicuously under the user’s …

Shotblocker® - Bionix® Senior Design, Samuel Dockery

Williams Honors College, Honors Research Projects

No abstract provided.

Biocorrosion Rate And Mechanism Of Metallic Magnesium In Model Arterial Environments, Patrick Bowen

Dissertations, Master's Theses and Master's Reports

A new paradigm in biomedical engineering calls for biologically active implants that are absorbed by the body over time. One popular application for this concept is in the engineering of endovascular stents that are delivered concurrently with balloon angioplasty. These devices enable the injured vessels to remain patent during healing, but are not needed for more than a few months after the procedure. Early studies of iron- and magnesium-based stents have concluded that magnesium is a potentially suitable base material for such a device; alloys can achieve acceptable mechanical properties and do not seem to harm the artery during degradation. …

Design And Creation Of A Device To Induce Vergence Eye Movements, Jacob B. Jaminet, Paul A. Wetzel

Undergraduate Research Posters

Automated eye-tracking systems can detect and analyze eye movements as a means to accurately diagnose more than 20 neurological diseases including mild traumatic brain injury. Mild traumatic brain injury is an occurrence of injury to the head resulting from blunt trauma or from acceleration or deceleration forces. Eye movement refers to the voluntary or involuntary movement of the eyes, helping in acquiring, fixating and tracking visual stimuli. There are three types of voluntary eye movement to track objects: smooth pursuit, vergence shifts and saccades. Vergence shifts are eye movements where the eyes move in opposite directions: moving to the midline …