Biological Engineering Commons^™

Design And Characterization Of A Pulsed Electric Field Chamber For Microalgae Lysis, Connor Strutin

Electrical Engineering

Microalgae are a promising renewable source of biofuel due to their high lipid content and rapid growth rates; however, algae cells must be electroporated (lysed) to release these lipids. The system developed in this project applies short (40 μs–10 ms), high-intensity (up to 33 kV/cm) pulsed electric fields (PEF) across cell membranes to enable electroporation.

Our lab-scale PEF chamber generates uniform, high-intensity electric fields using parallel-plate electrodes with sub-millimeter spacing. The system is designed to efficiently lyse microalgae cells for lipid extraction and biofuel production.

Central Pattern Generator Test Bench Report, Stephanie Wing-Yee Lee, Dustin Wong, Joseph Hernandez

Electrical Engineering

The project presents the design, fabrication, and implementation of a PCB test bench that interfaces with a custom VLSI chip designed to emulate the neural activity of a Central Pattern Generator (CPG). The test bench provides a precise and reliable platform for supporting signal operations and validating neuromorphic functionality. The design integrates both analog and digital circuitry to provide stable biasing, signal routing, and measurement access for chip characterization. The incorporation of op-amp buffers and adjustable potentiometers enables precise voltage tuning, resulting in controlled neuron-like behavior within the custom IC. The two-layer PCB supports modular interfacing with standard laboratory instruments …

Comprehensive Mechatronic Design Methodology For 6-Dof Stationary Lower Limb Rehabilitation Exoskeleton Robot With Safety-Integrated Control Architecture, Javlonbek Rakhmatillaev Mr., Nodirbek Kimsanboyev Mr., Umidjon Takabaev Mr., Zafar Juraev3 Dr.

Chemical Technology, Control and Management

This paper presents the mechatronic design of a proposed six-degree-of-freedom (6-DOF) stationary lower limb rehabilitation exoskeleton (SLLRE) robot, developed through a comprehensive mechatronic design methodology that includes mechanical design, actuator and sensor selection, and the development of a control structure based on a safety-oriented control approach. The proposed 6-DOF SLLRE mechanical design introduces a comprehensive mechanical structure comprising bilateral hip, knee, and ankle joints, degrees of freedom, joint ranges of motion, human parameters for rehabilitation training, as well as the frames and structural elements of the proposed system. Furthermore, the selection of appropriate sensors, actuators, and control architecture for the …

Optimizing Beer Fermentation Through Intelligent Control, Azizbek Nodirbekovich Yusupbekov, Mirjalol Yusupov

Chemical Technology, Control and Management

This paper presents an intelligent control approach for optimizing the beer fermentation process using fuzzy logic and adaptive neuro-fuzzy inference systems. By incorporating multivariable inputs—temperature error and pH deviation—the proposed system effectively handles the nonlinear dynamics and biological variability inherent in fermentation. Simulation results demonstrate improved control accuracy, responsiveness, and robustness compared to conventional methods, making the approach suitable for integration in modern brewery automation systems.

A Smart System For Detecting Anatomic And Histological Symptoms Of Diseased Agricultural Plants, Rustam Baratov, Himola Sunnatillayeva, Alimardon Mamatovich Mustafoqulov

Chemical Technology, Control and Management

This study describes a novel agricultural plant disease detecting smart system, capable of handling measured plant body parameters and images received by high resolution camera at the same time. The proposed plant disease detection method is based on evaluation of the signals received by measured and controlled plant body physical parameters like resistance, temperature and capacitance of the plant stem and image processing. An analogue plant model based on an electrical circuit with distributed parameters was developed. In addition, in the article the block diagram of the smart system for the early detection of plant diseases, the circuit diagram, its …

Novel Electrophysiological Biomarkers In Pediatric Drug Resistant Epilepsy And Genetic Epilepsy Syndromes, Sakar Rijal

Bioengineering Dissertations - Archive

Pediatric epilepsies, particularly those that are drug-resistant or genetically driven, represent some of the most complex neurological disorders encountered in childhood. Central to their pathophysiology is a disruption in the delicate balance between cortical excitation and inhibition (E/I), often resulting from impaired GABAergic interneuron function. This imbalance manifests as aberrant network dynamics and altered neural oscillations, giving rise to seizures and long-term cognitive impairments. In this thesis, we developed a translational framework to identify electrophysiological biomarkers that (i) assess cortical E/I imbalance and (ii) map epileptogenic zones, with the aim of enhancing diagnosis, guiding surgical planning, and informing therapeutic monitoring …

Jovial Family Farm Facilitates Intergenerational Learning Opportunities Through Urban Farming, Maera Williams

Purdue Journal of Service-Learning and International Engagement

Maera Williams is a sophomore in Environmental and Ecological Engineering at Purdue University. She joined the Engineering Projects in Community Service (EPICS) Urban Farming team as a freshman and now serves as project manager of ten undergraduate students collaborating with Jovial Family Farm to design and develop three indoor hydroponics systems for a laboratory space on their property in Broad Ripple, IN. Jovial Family Farm is a nonprofit organization founded by Drs. Bobbie and Brian Jellison with the mission to provide senior citizens, their families, and their communities with meaningful engagement opportunities on an intergenerational scale through urban agricultural activities. …

Hypoxic Incubator: Improving Robustness/Reliability And Demonstrating Physiological Efficacy, Damon Dennis Tan

Master's Theses

The Microphysiological Systems Laboratory aims to develop colorectal cancer tumor models under a hypoxic environment to assess model response to pharmaceutical compounds in vitro. To perform relevant studies, researchers have attempted to use different hypoxic inducing strategies such as a nitrogen pod and hypoxic incubator to recreate in vivo physiological responses to hypoxia. However, studies would be interrupted due to incubator functionality failure. To ensure successful and physiologically relevant studies, I improved and verified the robustness and reliability of a hypoxic incubator previously designed and manufactured in the lab. Through the testing and iterating design processes, I engineered and implemented …

3d Printed Microfluidic Fabrication Methodology, Characterization, Mechanical Design, And Applications In Electrostatic Artificial Muscles And Benthic Microbial Fuel Cells, Terak B. Hornik

Master's Theses

The fabrication of microfluidic devices often requires specialized methods. The development of these methods requires careful characterization and understanding of the processes involved. Using primarily PolyJet 3D printing technology, microfluidics offers a wide scope of applications such as microfluidic benthic microbial fuel cells (MBMFCs) and electrostatic artificial muscles. MBMFCs benefit from the confinement of the microbes resulting in close proximity between the electrode and the organisms. Using a modular design called the Sponge, assembly and upscaling is possible. Electrostatic artificial muscles benefit from a microfluidic approach due to the non-linearity of electrostatic attraction creating disproportionate benefits when miniaturized. When designed …

Shape Memory Alloy Capsule Micropump For Drug Delivery Applications, Youssef Mohamed Kotb

Theses and Dissertations

Implantable drug delivery devices have many benefits over traditional drug administration techniques and have attracted a lot of attention in recent years. By delivering the medication directly to the tissue, they enable the use of larger localized concentrations, enhancing the efficacy of the treatment. Passive-release drug delivery systems, one of the various ways to provide medication, are great inventions. However, they cannot dispense the medication on demand since they are nonprogrammable. Therefore, active actuators are more advantageous in delivery applications. Smart material actuators, however, have greatly increased in popularity for manufacturing wearable and implantable micropumps due to their high energy …

Spectrophotometric Device For Early Malaria Detection, Adrian Wasylewski, Christopher Faber, Victor Lin

Honors Thesis

Malaria remains a significant global health challenge, with millions of cases reported annually, particularly in resource-limited regions. Timely and accurate diagnosis is crucial for effective treatment and disease management. Unfortunately, there are still significant challenges in existing testing procedures, which are often expensive, inaccurate, or impractical for mass testing. While spectrophotometry has been proposed as a detection tool for other tropical diseases such as dengue fever, no prototype has been made for any disease, including malaria. This report addresses this gap by presenting a spectrophotometric-based malaria detection tool that achieves high sensitivity at a low cost. The inclusion of a …

Life Cycle Assessment Of Air Classification As A Sulfur Mitigation Technology In Pine Residue Feedstocks, Ashlee Edmonson

Theses and Dissertations--Biosystems and Agricultural Engineering

Sulfur accumulation during biofuel production is pollutive, toxic to conversion catalysts, and causes the premature breakdown of processing equipment. Air classification is an effective preprocessing technology for ash and sulfur removal from biomass feedstocks. A life cycle assessment (LCA) sought to understand the environmental impacts of implementing air classification as a sulfur-mitigation technique for pine residues. Energy demand and material balance for preprocessing were simulated using SimaPro and the Argonne National Laboratory’s GREET model, specifically focusing on comparing the global warming potential (GWP) of grid electricity versus bioelectricity scenarios. Overall, the grid electricity scenario had a GWP impact over 7 …

Fiber-Based Time-Correlated Single Photon Counting As A Method For Investigating Metabolism During Tetanic Contraction Of Skeletal Muscle, Kathryn Miller Priest

Graduate Theses and Dissertations

Nicotinamide adenine dinucleotide (NAD) is a cofactor that serves to shuttle electrons during metabolic processes such as glycolysis, the tricarboxylic acid cycle, and oxidative phosphorylation (OXPHOS) [1-5]. The reduced form of NAD, NADH, is autofluorescent, making it a measurable characteristic in the investigation of metabolic changes. The fluorescence lifetime of NADH is dependent on the state of protein binding, specifically free or bound NADH, allowing for detection of metabolic shifts between glycolysis (free NADH) and OXPHOS (bound NADH) [6-16]. Fiber-coupled time-correlated single photon counting (TCSPC) equipped with an implantable needle probe can be used to measure NADH lifetime in vivo …

Hypoxic Incubation Chamber, Simone Lisette Helfrich, Makenzie Nicole Jones

Biomedical Engineering: Graduate Reports and Projects

This paper describes the design, manufacturing, and testing of a novel controllable hypoxic incubator with fully functional oxygen gas control and temperature control in a humid environment. On the current market, a majority of the few hypoxic incubators use pre-mixed gas that does not offer precise control over gas concentration. The objective for this project was to create a chamber that allows the user to set the O2 concentration to varying set points of % O2 while maintaining the chamber at a constant body temperature, CO2 level, humidity, and sterility. To start the project, multiple concepts were developed for the …

Design Of Control Logic And The Human-Machine Interface For A Demonstration Plant Growth Chamber Implemented On A Programmable Logic Controller, Rachael Koehler

Biological and Agricultural Engineering Undergraduate Honors Theses

This honors thesis covers the planning, development, and implementation of system controls and human-machine interface (HMI) for a demonstration plant growth chamber. The work is a continuation of an ongoing project to be used as an educational and recruiting tool manifesting the skills acquired from the Biological and Agricultural Engineering Department at the University of Arkansas’ College of Engineering. This work includes emergency controls, overall design interface, and controls for both the aeration and lighting subsystems of the growth chamber. Overall design interface controls established included development of two user modes, Administrator and Visitor. The Administrator user will have full …

Performance And Economics Of Solar Inverters And Module Level Power Electronics In A 1 Mw Photovoltaic System, Maxwell Criswell

Biological and Agricultural Engineering Undergraduate Honors Theses

Photovoltaic solar panels convert sunlight to electricity in the form of direct current; therefore, a necessary component of every photovoltaic system is an inverter to convert the electricity to usable alternating current. There are various commercially available inverter technologies manufactured today such as microinverters, string inverters, and central inverters, as well as module level power electronic devices such as DC optimizers that are capable of improving system performance in string and central inverter systems. This thesis compares the performance and economics of five different inverter and module level power electronic systems through model simulation using Helioscope software. The five alternatives …

Development Of Light Actuated Chemical Delivery Platform On A 2-D Array Of Micropore Structure, Hojjat Rostami Azmand, Hojjat Rostami Azmand

Dissertations and Theses

Localized chemical delivery plays an essential role in the fundamental information transfers within biological systems. Thus, the ability to mimic the natural chemical signal modulation would provide significant contributions to understand the functional signaling pathway of biological cells and develop new prosthetic devices for neurological disorders. In this paper, we demonstrate a light-controlled hydrogel platform that can be used for localized chemical delivery in a high spatial resolution. By utilizing the photothermal behavior of graphene-hydrogel composites confined within micron-sized fluidic channels, patterned light illumination creates the parallel and independent actuation of chemical release in a group of fluidic ports. The …

Opendrop Software Development, Jiajun Guan

Electrical Engineering

To be able to transfer and mix solutions more efficiently and accurately during biology experiments, the Electrical Engineering department at Cal Poly University is planning to purchase or engineer the OpenDrop device. The OpenDrop device uses electro-wetting technology to control the movement of small droplets of water on a planar electrode array to transport and mix different solutions. This device is an open-source project and could be purchased online through the GaudiLab. The basic code of the system could be found in GitHub. With this code as a reference, the goal of this senior project is to develop the firmware, …

Blood Glucose Predictor, Jessica Patterson

Electrical Engineering

For my senior project, I perform data analysis using statistical methods to determine body metrics that correlate with blood glucose levels. Working with Dr. Tina Smilkstein, I take repeat measurements from 6 different volunteers to establish trends in bodily metric data. The data taken includes weight, body fat, pulse rate, VO2, blood glucose, blood pressure, hours slept, and quality of sleep. Using these values, I use the program MiniTab to view results.

A few examples of correlations with blood glucose found in this project are:

• Systolic blood pressure for females had a regression line of 124.0 -0.3366*Blood Pressure. This indicates …

Developing An Optomechanical Approach For Characterizing Mechanical Properties Of Single Adherent Cells, Ali Mehrnezhad

LSU Doctoral Dissertations

Mechanical properties of a cell reflect its biological and pathological conditions including cellular disorders and fundamental cellular processes such as cell division and differentiation. There have been active research efforts to develop high-throughput platforms to mechanically characterize single cells. Yet, many of these research efforts are focused on suspended cells and use a flow-through configuration. Therefore, adherent cells are detached prior to the characterization, which seriously perturbs the cellular conditions. Also, methods for adherent cells are limited in their throughput.

My study is aimed to fill the technical gap in the field of single cell analysis, which is a high-throughput …

Stability Analysis Of A More General Class Of Systems With Delay-Dependent Coefficients, Chi Jin, Keqin Gu, Islam Boussaada, Silviu-Iulian Niculescu

SIUE Faculty Research, Scholarship, and Creative Activity

This paper presents a systematic method to analyse the stability of systems with single delay in which the coefficient polynomials of the characteristic equation depend on the delay. Such systems often arise in, for example, life science and engineering systems. A method to analyze such systems was presented by Beretta and Kuang in a 2002 paper, but with some very restrictive assumptions. This work extends their results to the general case with the exception of some degenerate cases. It is found that a much richer behavior is possible when the restrictive assumptions are removed. The interval of interest for the …

Microfluidic Electrical Impedance Spectroscopy, John J. Foley

Master's Theses

The goal of this study is to design and manufacture a microfluidic device capable of measuring changes in impedance valuesof microfluidic cell cultures. Tocharacterize this, an interdigitated array of electrodes was patterned over glass, where it was then bonded to a series of fluidic networks created in PDMS via soft lithography. The device measured ethanol impedance initially to show that values remain consistent over time. Impedance values of water and 1% wt. saltwater were compared to show that the device is able to detect changes in impedance, with up to a 60% reduction in electrical impedance in saltwater. Cells were …

Wearable Assistive Technologies For Autism: Opportunities And Challenges, Emma Mansouri Benssassi, Juan-Carlos Gomez, Louanne E. Boyd, Gillian R. Hayes, Juan Ye

Engineering Faculty Articles and Research

Autism is a lifelong developmental condition that affects how people perceive the world and interact with others. Challenges with typical social engagement, common in the autism experience, can have a significant negative impact on the quality of life of individuals and families living with autism. Recent advances in sensing, intelligent, and interactive technologies can enable new forms of assistive and augmentative technologies to support social interactions. However, researchers have not yet demonstrated effectiveness of these technologies in long-term real-world use. This article presents an overview of the social and sensory challenges of autism, which offer great opportunities and challenges for …

Computer-Aided Diagnoses (Cad) System: An Artificial Neural Network Approach To Mri Analysis And Diagnosis Of Alzheimer's Disease (Ad), Berizohar Padilla Cerezo

Master's Theses

Alzheimer’s disease (AD) is a chronic and progressive, irreversible syndrome that deteriorates the cognitive functions. Official death certificates of 2013 reported 84,767 deaths from Alzheimer’s disease, making it the 6th leading cause of death in the United States. The rate of AD is estimated to double by 2050. The neurodegeneration of AD occurs decades before symptoms of dementia are evident. Therefore, having an efficient methodology for the early and proper diagnosis can lead to more effective treatments.

Neuroimaging techniques such as magnetic resonance imaging (MRI) can detect changes in the brain of living subjects. Moreover, medical imaging techniques are the …

The Subject Librarian Newsletter, Engineering And Computer Science, Fall 2017, Buenaventura "Ven" Basco

Libraries' Newsletters

No abstract provided.

Ionic Basis Of Ventricular Action Potentials, Ariel L. Escobar

Science Seminar Series

Dr. Escobar will talk about his cutting-edge approach to understanding molecular mechanisms underlying electrical activity in the heart.

Mechanical Reliability Of Implantable Polyimide-Based Magnetic Microactuators For Biofouling Removal, Christian G. Figueroa-Espada, Qi Yang, Hyowon Lee

The Summer Undergraduate Research Fellowship (SURF) Symposium

Hydrocephalus is a neurological disorder that typically requires a long-term implantation of a shunt system to manage its symptoms. These shunt systems are notorious for their extremely high failure rate. More than 40% of all implanted shunt systems fail within the first year of implantation. On average, 85% of all hydrocephalus patients with shunt systems undergo at least two shunt-revision surgeries within 10 years of implantation. A large portion of this high failure rate can be attributed to biofouling-related obstructions and infections. Previously, we developed flexible polyimide-based magnetic microactuators to remove obstructions formed on hydrocephalus shunts. To test the long-term …

Utilizing Brain-Computer Interfacing To Control Neuroprosthetic Devices, Cheyne J. Angy

Senior Honors Theses

Advances in neuroprosthetics in recent years have made an enormous impact on the quality of life for many people with disabilities, helping them regain the functionality of damaged or impaired abilities. One of the main hurdles to regaining full functionality regarding neuroprosthetics is the integration between the neural prosthetic device and the method in which the neural prosthetic device is controlled or manipulated to function correctly and efficiently. One of the most promising methods for integrating neural prosthetics to an efficient method of control is through Brian-computer Interfacing (BCI). With this method, the neuroprosthetic device is integrated into the human …

Midfield Rf Signal Detector, Dawei Zhang

Electrical Engineering

This project is part of a Master’s thesis which looks at alternative ways to measure blood glucose. The Master’s thesis uses mid-field signals in order to match impedance and therefore lose less power as they travel through flesh. The goal of this senior project is to build a receiver for those signals and give accurate RSSI (received signal strength indicator) measurements. Mid-fields were originally explored by Stanford professor Dr. Ada Poon [3] who used the signaling technique to recharge the batteries of deeply implanted devices. Devices implanted near the surface of the skin were able to have their batteries recharged …

Design And Development Of Two Component Hydrogel Ejector For Three-Dimensional Cell Growth, Thomas Dunkle, Jessica Deschamps, Connie Dam

Honors Scholar Theses

Hydrogels are useful in wound healing, drug delivery, and tissue engineering applications, but the available methods of injecting them quickly and noninvasively are limited. The medical industry does not yet have access to an all-purpose device that can quickly synthesize hydrogels of different shapes and sizes. Many synthesis procedures that have been developed result in the formation of amorphous hydrogels. While generally useful, amorphous hydrogels exhibit limited capability in tissue engineering applications, especially due to their viscous properties. This endeavor aims to modulate the appropriate gelation parameters, optimize the injection process, and create a prototype that allows for the extrusion …