Biomedical Engineering and Bioengineering Commons^™

Modeling The Long Term Effects Of Alendronate On Bone Mass Preservation Of The Femur With Articular Surface And Total Hip Replacements, Trevor J. Hryce

Master's Theses

Calculating femoral bone density changes after hip arthroplasty is of interest to researchers and clinicians for predicting the longevity of the prosthetic implant and the surrounding bone. Recently clinicians have been administering bisphosphonate drugs in an attempt to reduce the bone resorption due to stress shielding caused by these implants. Current strain-adaptive computational models with bisphosphonate treatment don’t predict the long term effects or look at treatment with hip resurfacing implants. The main goal of this study was to create and validate a computer model of the human femur incorporating a bone remodeling algorithm based on biological remodeling processes and …

Finite Element Analysis And Modeling Of A .38 Lead Round Nose Ballistic Gelatin Test, Danielle Datoc

Master's Theses

Firearms are present in two-thirds of United States households. As of 2003, roughly 500,000 projectile wounds occur annually in the United States. This costs an estimated 2.3 billion dollars of medical spending. The best treatment of gunshot wounds relies heavily on experience, but even with experience the unpredictable nature of ballistics can make treatment difficult.

Wound ballistics studies the injury pattern of a particular bullet. Ballistic gelatin tests are used to analyze this pattern. A block of 10 or 20% ballistic gelatin is set and a bullet is fired through the block. Key characteristics of the wound profile seen in …

An Investigative Study Into The Relationship Of Bone Morphogenetic Protein Antagonist Expression And Osteocyte Density By Region And Quadrant, Scott C. Mosher

Master's Theses

The role of cytokines and cell behavior and viability with respect to bone remodeling and bone behavior is an exciting area of orthopedic research. The purpose of this study was to investigate the relationships between BMP antagonist expression and osteocyte density, lacunar densities and osteocyte viability in cortical bone. Samples of unloaded tibial bone obtained from six C57Bl/6 mice were immunohistochemically stained for gremlin and noggin expression and also underwent methyl green staining to determine osteocyte presence. Bone sections were divided into four quadrants (cranial, caudal, medial and lateral) and three regions (proximal, mid shaft and distal), followed by analysis …

Biomechanical Comparison Of Wire Circlage And Rigid Plate Fixation For Median Sternotomy Closure In Human Cadaver Specimens, Mark Steven Wong

Master's Theses

Background:

Over 700,000 patients per year undergo open-heart surgery. Healing complication rates can be up to 5% of patients who undergo this procedure, with a morbidity rate of 50% if mediastinitis supervenes. A secure and rigid fixation of surgically divided sternum is critical to avoid healing complications. The purpose of this study was to compare the yield load, construct stiffness, ultimate load, displacement at ultimate load, and post-yield behavior of three sternotomy closure methods (Peristernal wires or Sternalock titanium plates) when stressed in each of three directions: lateral distraction, rostro-caudal (longitudinal) shear distraction, and anterior-posterior (transverse) shear in a cadaveric …

St Monitoring On The Programmer For Implantable Cardioverter Devices, Sarina Satya

Master's Theses

Cardiovascular disease is one of the most prevalent causes of death which has a high mortality rate. If identified early and treated appropriately, the mortality in patients with cardiovascular disease can be hugely reduced. For several decades, 12-Lead ECG has been the standard technique used to identify ischemia, and recent studies have shown that intracardiac electrogram has many benefits over external monitoring such as holter. ST Monitoring feature has been added to St. Jude Medical intracardiac cardioverter defibrillators (ICD) to leverage the ECG technology for identifying cardiovascular disease. This algorithm monitors the intracardiac electrogram to detect and report patterns which …

An Investigation Of Humeral Stress Fractures In Racing Thoroughbreds Using A 3d Finite Element Model In Conjunction With A Bone Remodeling Algorithm, Ryan James Moore

Master's Theses

The humerus of a racing horse Thoroughbred is highly susceptible to stress fractures at a characteristic location as a result of cyclic loading. The propensity of a Thoroughbred to exhibit humeral fracture has made equines useful models in the epidemiology of stress fractures. In this study, a racing Thoroughbred humerus was simulated during training using a 3D finite element model in conjunction with a bone remodeling algorithm. Nine muscle forces and two contact forces were applied to the 3-dimensional finite element model, which contains four separate load cases representing fore-stance, mid-stance, aft-stance, and standing. Four different training programs were incorporated …

Merlin.Net Automation Of External Reports Verification Process, Gabriel John Wettlaufer

Master's Theses

Merlin.net Patient Care Network is a St. Jude Medical product that is used for remote patient management. The basic concept of Merlin.net is to allow the physician to view patient device follow-up information as well as general patient and device information on a web application. The Merlin.net system also interfaces with the patient and will send them notification if they miss a follow-up. All device information will be collected automatically while the patient is sleeping. This information is sent through a telephone line to a Merlin.net server to process a report package and display the collected information on the Merlin.net …

Impaired Vascular Reactivity Following Chronic Ischemia In The Arteries Of The Mouse Hindlimb, Thomas (Tom) Kesler

Biomedical Engineering

Collateral dependent hyperemia is reduced following chronic ischemia, but the contribution of individual vessel reactivity is unknown. Further, it is not known what aspect of the complex ischemic injury response impacts vascular reactivity. To determine the impact of ischemia on vascular reactivity, we measured functional vasodilation in the muscular branch artery following resection of the femoral artery proximal to the muscular branch. On day-14 after surgery the diameter of the muscular branch was measured using side-stream dark field (SDF) imaging intravital microscopy. At moderate intensity skeletal muscle contraction (1mA, 200µs, 8Hz, 90sec), functional vasodilation is reduced compared to the contralateral …

Morphological Assessment Of Basic Multicellular Unit Resorption Parameters In Dogs Shows Additional Mechanisms Of Bisphosphonate Effects On Bone, Matthew R. Allen, Antonia M. Erickson, Xiang Wang, David B. Burr, R. Bruce Martin, Scott J. Hazelwood

Biomedical Engineering

Bisphosphonates (BPs) slow bone loss by reducing initiation of new basic multicellular units (BMUs). Whether or not BPs simply prevent osteoclasts from initiating new BMUs that resorb bone or also reduce the amount of bone they resorb at the BMU level is not clear. The goal of this study was to determine the effects of BPs on three morphological parameters of individual BMUs, resorption depth (Rs.De), area (Rs.Ar), and width (Rs.Wi). After 1 year of treatment with vehicle (VEH), alendronate (ALN; 0.10, 0.20, or 1.00 mg/kg/day), or risedronate (RIS; 0.05, 0.10, or 0.50 mg/kg/day), resorption cavity morphology was assessed in …

Impaired Vascular Reactivity Following Chronic Ischemia In The Arteries Of The Mouse Hindlimb, Trevor Cardinal, Thomas J. Kesler, Matthew D. Yocum, Tyler S. Smith, Nolan M. Mott

Biomedical Engineering

No abstract provided.

Single Cell Impedance Measurements Using Microfabricated Electrodes And Labview Graphical Programming, Stephanie Sophia Hernandez

Master's Theses

This Master’s Thesis project consists of the research, design, and fabrication of a system that could perform broadband impedance measurements (1kHz-20Mhz) of single cells using National Instruments Labview data acquisition and programming in coordination with a single cell capture device. Presented first is the background information on cells and their electrical properties, along with background in micro-total-analysis systems as well as impedance spectroscopy. Experimental Methods are then discussed for the electrode design, cellular modeling in COMSOL, fabrication methods, and Labview 8.0 Set-up and programming. Measurements were performed using the single-cell capture device on saline, yeast cells, and a polysterene bead. …

Laser Scanning Confocal Microscopy (Lscm): An Application For The Detection Of Morphological Alterations In Skin Structure, Shea C. Smith

Master's Theses

Laser scanning confocal microscopy (LSCM) is an optical imaging technique that provides improved resolution and sensitivity over conventional methods of optical microscopy. However, the cost of most commercial LSCM systems exceeds the financial limitations of many smaller laboratories. The design of a custom LSCM created at a fraction of the cost of a commercial model is discussed in this paper.

The increase in the incidence rate of skin cancer in the world today is alarming, as such, it is essential to provide an early, rapid and effective method for in vivo diagnostics of human skin tissue. LSCM is capable of …

The Electrical Properties Of Human Tissue For The Diagnosis And Treatment Of Melanoma Skin Cancer, Glenn Cameron Stante

Master's Theses

This thesis discusses the research, experimental methods, and data gathered for the investigation of a novel method for the diagnosis of melanoma skin cancer. First, a background about human skin tissue is presented. Then, a detailed description of melanoma along with current diagnosis techniques and treatment options are presented. In the experimental methods, the electrical properties of several types of tissue were analyzed, the purpose of which was to discover if a tissue type can be distinguished by its electrical properties alone. This would allow for the diagnosis of melanoma to be done by examining the electrical properties of the …

A Computational Model Of Apoptotic Osteocyte Correlation To Cortical Bone Remodeling Parameters, Michael Stephen Alexander

Master's Theses

The onset of osteoporosis caused by aging, disease states, and post-menopausal conditions significantly impacts patient quality of life, required healthcare funding, personal autonomy losses from increased fracture risk and the subsequent corrective surgery. Research has indicated that osteocyte apoptosis may be a key parameter in bone remodeling, raising the possibility of remodeling rate modulation for the mitigation of bone mass resorption. By developing therapies that target osteocyte apoptosis, it may be possible to prevent undesired bone remodeling activity while maintaining a healthy balance between damage formation in the form of microcracks induced by the strain environment and the removal of …

A Rapid Prototyping Method For Constructing A Complex Three-Dimensional Substrate, Kathryn Jacoba Hart

Master's Theses

Cell culturing on three-dimensional structures has increased the possibilities in tissue engineering and bioreactor research. These structures enable cells to differentiate, proliferate, mobilize, and function in a conformation that more accurately mimics in vivo conditions. Computer generated models aid in development and rapid alteration of three-dimensional cell substrates, defining their internal structure as well as their external morphology. The rapid transition from substrate design to a viable culture is imperative to quickly advance research in biomedical and tissue engineering applications.

The aim of this thesis is to investigate the feasibility of a rapid prototyping process by selectively cross-linking and assembling …

Material Properties Are Related To Stress Fracture Callus And Porosity Of Cortical Bone Tissue At Affected And Unaffected Sites, Rachel C. Entwistle,, Sara C. Sammons, Robert F. Bigley, Scott J. Hazelwood, David P. Fyhrie, Jeffery C. Gibeling, Susan M. Stover

Biomedical Engineering

Stress fractures are overuse injuries of bone that affect elite athletes and military recruits. One response of cortical bone to stress fracture is to lay down periosteal callus. The objectives of this study were to determine if material properties are different among bones with different stages of stress fracture callus, at both a callus site and at a distal site. Cortical specimens were mechanically tested to determine their stress–strain response. Material property differences were examined using nonparametric and regression analyses. At the callus site, material properties were low during the earliest stages of callus, higher with increasing callus maturity, but …

Regression Analysis Of Fracture Toughness For Secondary Osteons Located In Human Cortical Bone, Chase A. Fetzer

Master's Theses

An experiment was carried out in order to locate and quantify osteon types within a sample of cortical bone taken from a human tibia. This was done using a microscope-camera assembly and the BioQuant computer software. The results of this were correlated with a previous experiment’s results on fracture toughness so that an analysis could be run on the data in order to determine the factors that most affect the value of fracture toughness of this cortical bone. Results were examined closely and the analysis repeated until the author was satisfied that the best possible model for fracture toughness had …

Compliance Calibration For Fracture Testing Of Anisotropic Biological Materials, J. A. Creel, S. M. Stover, R. B. Martin, D. P. Fyhrie, S. J. Hazelwood, J. C. Gibeling

Biomedical Engineering

The compliance technique has been used to monitor crack length during fracture and fatigue testing of materials. Difficulties arise when this technique is applied to anisotropic biological materials such as bone. In this tutorial, two different methods of analyzing compliance calibration data are described: the standard ASTM method and a new approach developed by the authors specifically for anisotropic materials. An example is given showing how data from equine cortical bone can be analyzed. In this example, calibration tests were conducted on thirty-six three point bend specimens machined from the middiaphysis of six pairs of equine third metacarpal bones. Cracks …

A Biomechanical Comparison Of Locked Plate Fixation With Percutaneous Insertion Capability Versus The Angled Blade Plate In A Subtrochanteric Fracture Gap Model, Brett D. Crist, Afshin Khalafi, Scott J. Hazelwood, Mark A. Lee

Biomedical Engineering

Objectives: The angled blade plate has been the historical standard in fixed-angle extramedullary subtrochanteric femur fracture fixation, but it requires an extensile lateral approach to the femur. Little formal evaluation exists for specifically designed percutaneous extramedullary implants. The purpose of this study was to compare 3 locked plating constructs, all with percutaneous insertion capability, with the standard 95-degree angled blade plate to determine whether specifically designed fixed-angle extramedullary implants for subtrochanteric femur fractures were biomechanically comparable to the angled blade plate.

Methods: Forty composite adult femurs were divided into 4 equal groups. The constructs evaluated included a 95-degree angled blade …

A Modification To The Group Delay And Simulated Annealing Technique For Characterization Of Peripheral Nerve Fiber Size Distributions For Non-Deterministic Sampled Data, Robert B. Szlavik

Biomedical Engineering

The ability to determine the characteristics of peripheral nerve fiber size distributions would provide additional information to clinicians for the diagnosis of specific pathologies of the peripheral nervous system. Investigation of these conditions, using electro-diagnostic techniques, is advantageous in the sense that such techniques tend to be minimally invasive yet provide valuable diagnostic information. One of the principal electro-diagnostic tools available to the clinician is the nerve conduction velocity test. While the peripheral nerve conduction velocity test can provide useful information to the clinician regarding the viability of the nerve under study, it is a single parameter test that yields …

A Pdms Sample Pretreatment Device For The Optimization Of Electrokinetic Manipulations Of Blood Serum, Timothy J. Abram

Master's Theses

This project encompasses the design of a pretreatment protocol for blood serum and adaption of that protocol to a microfluidic environment in order to optimize key sample characteristics, namely pH, conductivity, and viscosity, to enable on-chip electrokinetic separations. The two major parts of this project include (1) designing a pretreatment protocol to optimize key parameters of the sample solution within a target range and (2) designing /fabricating a microchip that will effectively combine the sample solution with the appropriate buffers to replicate the same bench-scale protocol on the micro-scale.

Biomarker detection in complex samples such as blood necessitates appropriate sample …

Assessment Of Electrospinning As An In-House Fabrication Technique For Blood Vessel Mimic Cellular Scaffolding, Colby M. James

Master's Theses

Intravascular devices, such as stents, must be rigorously tested before they can be approved by the FDA. This includes bench top in vitro testing to determine biocompatibility, and animal model testing to ensure safety and efficacy. As an intermediate step, a blood vessel mimic (BVM) testing method has been developed that mimics the three dimensional structure of blood vessels using a perfusion bioreactor system, human derived endothelial cells, and a biocompatible polymer scaffold used to support growth of the blood vessel cells. The focus of this thesis was to find an in-house fabrication method capable of making cellular scaffolding for …

A Simple, Yet Effective, Demonstration Of Polymeric Mechanical Behavior, Lanny Griffin, Jeffrey Swab

Biomedical Engineering

Developing an appreciation for the mechanical behavior of polymers materials in a lecture mode can be challenging for students if they have not bad the benefit of a laboratory experience . We have developed a simp le demonstration of thermoplastic polymeric behav ior using low-density polyethylene bags. The demonstration illustrates strengthening, rate effects, and directionality of strengthening and stiffness. Following the demonstration, students are better ab le to articulate the influence of structure, properties, processing , and performance as it applies to thermoplastic polymers.

The Effect Of Particle Surface Area To Volume Ratio On Ion Release From Cocr Spheres, Darin J. Grandfield

Master's Theses

In 2005, over 200,000 Americans underwent a hip arthroplasty, the replacement of a hip joint with an artificial prosthesis. Of these arthroplasties, metal-on-metal type implants represent an increasing usage percentage. Metal-on-metal implants are selected largely for their low volumetric wear rate, durability, and resistance to corrosion. In spite of these advantages, little is known concerning the long-term consequences of heavy metal alloy use in the body, although early research indicates potentially carcinogenic results. This thesis is a preliminary investigation into these long term effects and their root causes.

An improved comprehension of the corrosion kinetics and the rate of ion …

Evaluating The Electrical Response Of Polyaniline To Mechanical Strain, Matthew L. Goebel

Master's Theses

This thesis focuses on the electrical output of polyaniline films subjected to uniaxial strain in hydrochloric acid solutions. Polyaniline belongs to novel class of materials known as conducting polymers. Alternating single and double bonds in the backbone of conducting polymers allow them to transmit electric charge when they are doped with negatively charged ions. Modifying the degree of doping and other electrical/chemical treatments allow conducting polymers to exhibit conducting, semi-conducting, or insulating electrical properties. Resilient mechanical properties, good processability, and low cost make conducting polymers good candidates for applications traditionally held by metals and semi-conductors.

When tensile strain is applied …

Preparation For Nerve Membrane Potential Readings Of A Leech, Laboratory Setup And Dissection Process, Jason Patrick Caulfield

Master's Theses

A well documented laboratory setup, leech preparation process, and bio-potential data recording process are needed. Repeatability and quality data recordings are essential and thus dictate the requirements of the laboratory setup and processes listed above. Advances in technology have both helped and hindered this development. While very precise equipment is required to record the low voltage bio-potentials, noisy electronic equipment and wires surrounding the work area provide high levels of interference. Proper laboratory setup and data recording processes, however, limit the unwanted interference. Quality data can only be recorded from a properly handled and prepared leech subject. Proper setup and …

Do Canines Experience The Effects Of Heart Rate Turbulence?, Melanie Ann Gurunathan

Master's Theses

Background

The canine cardiac system has been the model against which many Class III cardiac devices are validated. Thus, it is expected that the canine heart has very similar electrical model to that found in humans. In 1999, the absence of Heart Rate Turbulence (HRT) after a single Pre-Ventricular Contraction (PVC) was linked to high-risk patient after acute myocardial infarction. Studies of HRT were performed on high-risk patients with Holter-Monitors as were most subsequent HRT studies. If HRT could potentially be used as a risk factor of heart disease, it is interesting to study whether HRT is present following a …

Time-Frequency Analysis Of Intracardiac Electrogram, Erik Brockman

Master's Theses

The Cardiac Rhythm Management Division of St. Jude Medical specializes in the development of implantable cardioverter defibrillators that improve the quality of life for patients diagnosed with a variety of cardiac arrhythmias, especially for patients prone to sudden cardiac death. With the goal to improve detection of cardiac arrhythmias, this study explored the value in time-frequency analysis of intracardiac electrogram in four steps. The first two steps characterized, in the frequency domain, the waveforms that construct the cardiac cycle. The third step developed a new algorithm that putatively provides the least computationally expensive way to identifying cardiac waveforms in the …

Mechanical Simulation Of Articular Cartilage Based On Experimental Results, Kevin Matthew Stewart

Master's Theses

Recently, a constituent based cartilage growth finite element model (CGFEM) was developed in order to predict articular cartilage (AC) biomechanical properties before and after growth. Previous research has noted limitations in the CGFEM such as model convergence with growth periods greater than 12 days. The main aims of this work were to address these limitations through (1) implementation of an exact material Jacobian matrix definition using the Jaumann-Kirchhoff (J-K) method and (2) quantification of elastic material parameters based upon research findings of the Cal Poly Cartilage Biomechanics Group (CPGBG). The J-K method was successfully implemented into the CGFEM and exceeded …

The Impact Of Lipid Percentage On Fibrous Cap Stability In Atherosclerotic Lesions, Anita Lorraine Crompton

Master's Theses

Coronary artery disease (CAD) is a common cause of sudden cardiac death. Much of the disease is not completely understood, which makes treatment and prevention difficult. Many researchers are using technology, such as advanced imaging techniques and finite element analysis, to better understand the disease. While there is much progress being made to look at the analysis of actual excised diseased arteries, there is still not a standardized model to predict the future of any one lesion. The purpose of this study is to explore the possibility of creating a standardized model to predict the mechanical stability of the fibrous …