Automotive Engineering Commons^™

Development Of An Eco Approach And Departure Application To Improve Energy Consumption Of A Plug-In Hybrid Vehicle In Charge Depleting Mode, Brandon Narodzonek

Dissertations, Master's Theses and Master's Reports

A recent study at Michigan Technological University as part of the NEXTCAR DOE APRA-E Project was conducted to determine the potential energy savings of a plug-in hybrid electric vehicle (PHEV) equipped with various Connected and Automated Vehicle (CAV) Technologies. One aspect of this study focused on the development of an Eco Approach and Departure (Eco AnD) Application that would further reduce the energy consumed around a signalized intersection.

Many modern intersections are equipped with traffic signals that can broadcast Basic Safety (BSM), MAP, and Signal Phase and Timing (SPaT) message sets that contain intersection ID, location, current phase, and cyclic …

A Cfd Study Investigating Drag Reduction For Different Offset And Inline Distance For Two Trucks Platooning, Wael Mokhtar, Kyle Dinger, Shardul Kachare, Mdrazib Hossain, Colin Britcher

Mechanical & Aerospace Engineering Faculty Publications

The automotive industry invests huge resources to improve fuel consumption of commercial vehicles by improving their aerodynamic efficiency. Recently, numerous studies investigating the effect of platooning on aerodynamic drag of semi-trucks have been performed by researchers indicating a positive impact. For the present study, a three-dimensional computational study was performed to investigate the effect of varying offset and linear distance during platooning on the total drag of two semi-trucks. The study was conducted on a full-scale model using Reynold’s Averaged Navier-Strokes governing equations for a moving ground simulation using the STAR-CCM+ computational package. Furthermore, for turbulence, the standard k- …

Design Of An Anti-Jerk Controller For Both Locked And Slipping Torque Converter Conditions In A Vehicle, Syed Ahmad Nadeem

Dissertations, Master's Theses and Master's Reports

With the advancement in the automotive technologies, the customer scrutiny on the ride comfort of automobiles has come to light. Vehicle drivability is one of the important aspects that defines the ride comfort for a vehicle. Drivability of a vehicle is a qualitative measure and may differ from person to person, however, researches have come up to highlight a few parameters that can categorize the drivability performance of a vehicle into good or bad for a majority of the targeted audience. One of those parameters include shuffle, which is defined as the longitudinal oscillations that occurs in the drivetrain when …

Atv Dynamics And Pediatric Rider Safety, James T. Auxier Ii

Theses and Dissertations--Biomedical Engineering

It has been observed through numerous academic and governmental agency studies that pediatric all-terrain vehicle ridership carries significant risk of injury and death. While no doubt valuable to safety, the post-hoc approach employed in these studies does little to explain the why and how behind the risk factors. Furthermore, there has been no prolonged, widespread, organized, and concerted effort to reconstruct and catalog the details and causes of the large (20,000+) number of ATV-related injuries that occur each year as has been done for road-based motor vehicle accidents. This dissertation takes the opposite approach from a meta-analysis and instead examines …

Filtered-Dynamic-Inversion Control For Unknown Minimum-Phase Systems With Unknown Relative Degree, Sumit Suryakant Kamat

Theses and Dissertations--Mechanical and Aerospace Engineering

We present filtered-dynamic-inversion (FDI) control for unknown linear time-invariant systems that are multi-input multi-output and minimum phase with unknown-but-bounded relative degree. This FDI controller requires limited model information, specifically, knowledge of an upper bound on the relative degree and knowledge of the first nonzero Markov parameter. The FDI controller is a single-parameter high-parameter-stabilizing controller that is robust to uncertainty in the relative degree. We characterize the stability of the closed-loop system. We present numerical examples, where the FDI controller is implemented in feedback with mathematical and physical systems. The numerical examples demonstrate that the FDI controller for unknown relative degree …

A Study Of Model-Based Control Strategy For A Gasoline Turbocharged Direct Injection Spark Ignited Engine, Xin Wang

Dissertations, Master's Theses and Master's Reports

To meet increasingly stringent fuel economy and emissions legislation, more advanced technologies have been added to spark-ignition (SI) engines, thus exponentially increase the complexity and calibration work of traditional map-based engine control. To achieve better engine performance without introducing significant calibration efforts and make the developed control system easily adapt to future engines upgrades and designs, this research proposes a model-based optimal control system for cycle-by-cycle Gasoline Turbocharged Direct Injection (GTDI) SI engine control, which aims to deliver the requested torque output and operate the engine to achieve the best achievable fuel economy and minimum emission under wide range of …

Real-Time Predictive Control Of Connected Vehicle Powertrains For Improved Energy Efficiency, Joseph Oncken

Dissertations, Master's Theses and Master's Reports

The continued push for the reduction of energy consumption across the automotive vehicle fleet has led to widespread adoption of hybrid and plug-in hybrid electric vehicles (PHEV) by auto manufacturers. In addition, connected and automated vehicle (CAV) technologies have seen rapid development in recent years and bring with them the potential to significantly impact vehicle energy consumption. This dissertation studies predictive control methods for PHEV powertrains that are enabled by CAV technologies with the goal of reducing vehicle energy consumption.

First, a real-time predictive powertrain controller for PHEV energy management is developed. This controller utilizes predictions of future vehicle velocity …

Piezoelectric Energy Harvester Improvement, Nathan Embaugh, Jason Mack, Jeremiah Fitzgerald, Zachary J. Lindsey

Williams Honors College, Honors Research Projects

The energy harvester is used to convert a portion of the tire deflection waste energy to power up tire embedded sensors. A piezoelectric energy harvester is designed and some preliminary tests are done on it. So far, it has been shown that this design is sufficient for tire application. The team will need to modify the design of the energy harvester, the measurement setup and add a temperature and a strain senor to the existing setup so that the tire deflection and temperature can be measured and at the same time the energy harvester should be tested to see how …

Human Powered Vehicle Internal Systems Design, Zachary Broadbent, Jordan Boos, Patrick Gaertner, Caleb Miner

Williams Honors College, Honors Research Projects

The objective of this design project is to redesign the seat and steering system for the Human Powered Vehicle Team. The goal of the seat design is too improve ergonomics by making it more comfortable and adjustable. In making the seat adjustable, it will be easier for drivers to achieve an optimal efficiency when pedaling. The aim for steering will be to improve the ergonomics as well as performance by analyzing steering systems in the past and evaluating how each design was successful and for what reason. Another main goal of the steering system will be improving the stability and …

Autonomous Guided Vehicle Frame For Outdoor Use, Thomas Mcgrath

Williams Honors College, Honors Research Projects

The overall goal for my project is to design a durable Autonomous Guided Vehicle (AGV) frame intended for carrying a heavy load over outdoor terrain. I will not be designing a complete vehicle, only the basic structure that can be used to build a complete AGV on. There will be complete 3D models of the design and its individual parts. I also would like to provide limited Finite Element Analysis of the design using ANSYS software to determine weaknesses and methods for improvement. The design I create is meant to be used as a framework for complete outdoor AGV designs. …

Sensor Fusion And Non-Linear Mpc Controller Development Studies For Intelligent Autonomous Vehicular Systems, Ahammad Basha Dudekula

Dissertations, Master's Theses and Master's Reports

The demand for safety and fuel efficiency on ground vehicles and advancement in embedded systems created the opportunity to develop Autonomous controller. The present thesis work is three fold and it encompasses all elements that are required to prototype the autonomous intelligent system including simulation, state handling and real time implementation. The Autonomous vehicle operation is mainly dependent upon accurate state estimation and thus a major concern of implementing the autonomous navigation is obtaining robust and accurate data from sensors. This is especially true, in case of Inertial Measurement Unit (IMU) sensor data. The IMU consists of a 3-axis gyro, …

Implementation Of Radial Basis Function Artificial Neural Network Into An Adaptive Equivalent Consumption Minimization Strategy For Optimized Control Of A Hybrid Electric Vehicle, Thomas P. Harris

Graduate Theses, Dissertations, and Problem Reports (ETD)

Continued increases in the emission of greenhouse gases by passenger vehicles has accelerated the production of hybrid electric vehicles. With this increase in production, there has been a parallel demand for continuously improving strategies of hybrid electric vehicle control. The goal of an ideal control strategy is to maximize fuel economy while minimizing emissions. The design and implementation of an optimized control strategy is a complex challenge. Methods exist by which the globally optimal control strategy may be found. However, these methods are not applicable in real-world driving applications since these methods require a priori knowledge of the upcoming drive …

Route Planning For Long-Term Robotics Missions, Christopher Alexander Arend Tatsch

Graduate Theses, Dissertations, and Problem Reports (ETD)

Many future robotic applications such as the operation in large uncertain environment depend on a more autonomous robot. The robotics long term autonomy presents challenges on how to plan and schedule goal locations across multiple days of mission duration. This is an NP-hard problem that is infeasible to solve for an optimal solution due to the large number of vertices to visit. In some cases the robot hardware constraints also adds the requirement to return to a charging station multiple times in a long term mission. The uncertainties in the robot model and environment require the robot planner to account …

An Examination To Pathways Powering Car Using Clean Energy, Marina Miranda

Graduate Theses, Dissertations, and Problem Reports (ETD)

Traditional vehicles powered by internal combustion engines contribute significantly to increasing emissions of greenhouses gasses (GHG). There has been increasing interest in powering vehicles using green energy include using electricity produced by wind turbine and solar panel. The green electricity can be used to directly charge the Battery Electric Vehicles (BEV), or producing hydrogen as fuel for Fuel Cell Electric Vehicles (FCEV) by converting electrical energy to hydrogen (H₂) through water electrolysis. The low energy density H₂ produced can be stored on board as either compressed H₂ or liquefied H₂.

This research examines the …

Radio Frequency Studies Of Soot Loading And Ammonia Storage On A Diesel Particulate Filter With A Scr Catalyst Coating, Shreyans Sethia

Dissertations, Master's Theses and Master's Reports

The radio frequency (RF) measurement technique has been shown to be a viable method for measurement of the amount of soot loaded onto DPF’s ^[1] and the amount of NH₃ stored on SCR catalysts ^[2]. In one of the configurations, a microwave resonant cavity is formed by the metal can encasing the enclosed catalyst. Two metal probes acting as antennas are placed on either side of the catalyst. Power transmitted between the antennas is monitored as the frequency of the signal is swept. At certain frequencies, resonance is achieved. Measurements of the resonance frequencies, amplitude at resonance, and …

Measurement Of Current Distribution In The Land Channel Direction Of A Proton Exchange Membrane Fuel Cell, Chinmay Kulkarni

Dissertations, Master's Theses and Master's Reports

A fully functional proton exchange membrane fuel cell with single land channel geometry on the cathode and segmented anode current collector with 9 mm² active area with a 350μm spatial resolution was utilized to measure the local current distribution in the land channel direction. A distinguished printed circuit board approach was used for the data acquisition to adapt to any flow field design.

Performance of this segmented cell was examined at dry, wet and moderate humidity settings to study the water transport phenomenon in the PEMFC. In the dry condition at 60 ͦ C with 0% relative humidity, the …

Lightweight Racing Suspension, Colin Haynes

Honors Theses

The purpose of this senior design project is to design and optimize the new suspension system for Western Michigan University’s 2020 solar car. The current solar car was 43% heavier than the average solar car, and was the heaviest single occupant vehicle competing in the American Solar Challenge. The scope of the project is to reduce the weight as much as possible from the old 2016 suspension. The new suspension weighed 34.91 lbs less than the 2016 suspension system while maintaining a minimum factor of safety greater than 1.5, compliant with American Solar Challenge regulations. The design consists of a …

Development Of Mbd Model And Analysis Methodology For Vehicle Design, Alfonso Christopher Ponce

Mechanical Engineering ETDs

This thesis is to provide a new methodology that considers the effects the chassis applies during dynamic load to the suspension and the handling characteristics of a road course vehicle. A methodology in which is described in detail as well as an applied demonstration where literature before this thesis, lacks in replication and serves to establish a basis for multi-body dynamic analysis in this area. Two models to be created, rigid and flexible, and to compare each other to study the effects the chassis torsional stiffness has during load transfer. Ultimately, to assist in the design of a vehicle that …

Gesture Based Control Of Semi-Autonomous Vehicles, Brian Sanders

Computational Modeling & Simulation Engineering Theses & Dissertations

The objective of this investigation is to explore the use of hand gestures to control semi-autonomous vehicles, such as quadcopters, using realistic, physics based simulations. This involves identifying natural gestures to control basic functions of a vehicle, such as maneuvering and onboard equipment operation, and building simulations using the Unity game engine to investigate preferred use of those gestures. In addition to creating a realistic operating experience, human factors associated with limitations on physical hand motion and information management are also considered in the simulation development process. Testing with external participants using a recreational quadcopter simulation built in Unity was …

A Data Mining Methodology For Vehicle Crashworthiness Design, Xianping Du

Doctoral Dissertations and Master's Theses

This study develops a systematic design methodology based on data mining theory for decision-making in the development of crashworthy vehicles. The new data mining methodology allows the exploration of a large crash simulation dataset to discover the underlying relationships among vehicle crash responses and design variables at multiple levels and to derive design rules based on the whole-vehicle safety requirements to make decisions about component-level and subcomponent-level design. The method can resolve a major issue with existing design approaches related to vehicle crashworthiness: that is, limited abilities to explore information from large datasets, which may hamper decision-making in the design …

Electronic Cvt - Controls, Alec William Hardy, Jessalyn Leora Ann Bernick, Nicholas Esteban Capdevila, Tristan Charles Perry

Mechanical Engineering

The following document outlines the design process, manufacturing, and testing of the control system for an electronically controlled continuously variable transmission (ECVT). This control system was integrated into the custom designed and manufactured mechanical transmission system created in parallel by another senior project group. The transmission was designed for use in the Cal Poly Baja SAE vehicle. Through researching customer needs, competition requirements, previous and alternate CVT designs, and vehicle characteristics, we were able to determine the requirements and specifications for our unique system. Input, output, speed, and durability requirements guided our hardware selection. The primary components which comprised our …

Autonomous Vehicles Operating Collaboratively To Avoid Debris And Obstructions, Toan T. Le, Cole W. Oppenheim, James H. Gildart, Kyle M. Bybee

Mechanical Engineering

The purpose of this project is to demonstrate the safety and increased fuel efficiency of an automated collision avoidance system in collaborative vehicle platooning. This project was cosponsored by Daimler Trucks North America headquartered in Portland, Oregon, as well as Dr. Birdsong, and Dr. DeBruhl of Cal Poly. The mechanical engineering team consists of Cole Oppenheim, James Gildart, Toan Le, and Kyle Bybee who worked in coordination with a team of computer engineers. Vehicle platooning is a driving technique to increase the fuel efficiency of a group of vehicles by following a lead vehicle closely to reduce the drag experienced …

Comparison Of Lqr And Lqr-Mrac For Linear Tractor-Trailer Model, Kevin Richard Gasik

Master's Theses

The United States trucking industry is immense. Employing over three million drivers and traveling to every city in the country. Semi-Trucks travel millions of miles each week and encompass roads that civilians travel on. These vehicles should be safe and allow efficient travel for all. Autonomous vehicles have been discussed in controls for many decades. Now fleets of autonomous vehicles are beginning their integration into society. The ability to create an autonomous system requires domain and system specific knowledge. Approaches to implement a fully autonomous vehicle have been developed using different techniques in control systems such as Kalman Filters, Neural …

The Design Of An Innovative Automotive Suspension For Formula Sae Racing Applications, Jared Darius

Senior Honors Theses

This thesis details an analytical approach to an innovative suspension system design for implementation to the Formula SAE collegiate competition. It focuses specifically on design relating to geometry, mathematical modeling, energy element relationships, and computer analysis and simulation to visualize system behavior. The bond graph approach is utilized for a quarter car model to facilitate understanding of the analytical process, then applied to a comparative analysis between two transverse half car models. The second half car model contains an additional transverse linkage with a third damper, and is compared against the baseline of the first half car model without the …

Finite Element Model Validation And Testing Of An Off-Road Vehicle Under Dynamic Loading Conditions, Mackenzie Susan Cunningham

Doctoral Dissertations and Master's Theses

In the vehicle design life cycle, validation tests consume a significant portion of the available development time. With a short, one-year design cycle, the Embry-Riddle Baja Team leverages computer-aided engineering (CAE) tools to simulate critical test cases whose loading conditions can be accurately represented by a series of static loads and constraints. Using these conditions, a Finite Element Model (FEM) can be employed to accurately predict the effects of the loading conditions in the components. During the initial design of the front suspension, one major load case was determined to be the main failure load. However, after validation testing the …

Cfd Study Of Aerodynamic Drag Reduction Tool Of A Generic Sports Utility Vehicle (Suv), Samira Ishrat Jahan

Masters Theses

The Sports Utility Vehicle (SUV) has been a popular automobile choice in North America for over 50 years due to its seating and hauling versatility and good towing capacity. This widespread popularity has resulted in manufacturers pushing for increased horsepower and cabin size. Unfortunately, the limiting factor has been fuel economy which is governed by the vehicle aerodynamics. A reduction in aerodynamic drag can result in better fuel economy. The goal of this study is to reduce the aerodynamic drag of a generic SUV and the efficient application of drag reduction devices to control flow separation. An initial study has …

10_Fdr_Written_Project Central Vehicle Controller For Hybrid Racecar, Elias D. Bello, Trammell J. Saltzgaber, Leina C. Mcdermott, Alex S. Newman, Jennifer Jain

ENGS 89/90 Reports

Our ENGS 89/90 team has designed and tested a new central vehicle controller for the Dartmouth Formula Racing team's hybrid racecar. The new controller allows for the implementation of various control strategies, logs data from sensors onboard the vehicle, and is accompanied by well-documented firmware and hardware and an automotive-grade enclosure.

Torsional Stiffness Of A Race Car, Reiley A. Schraeger, Cameron Kao, Raymond Deng, Omar Roman

Mechanical Engineering

Torsional stiffness plays a major role in any road vehicle. To understand torsional stiffness of a vehicle and make future iterations and improvements, a proper torsional stiffness jig is required to prove accurate and useful data. This report encompasses the new and improved testing jig and potential improvement ideas for more accurate results. With real data result relating to FEA calculations, designers can be confident in the FEA changes to torsional stiffness is accurate and will yield the probably results they desired. This report shows the methodology, manufacturing process and testing procedure to use on any Baja or SAE vehicle …

Dynamic Analysis Of Vehicle Performance For Changes To Rear Axle Housing, Diane Peters, Yaomin Dong, Vimal Patel

Mechanical Engineering Presentations And Conference Materials

This paper explores the performance improvements of a 2013 Ford Mustang Shelby GT500 resulting from changes to the rear axle housing. In previous work, described in [1, 2], the rear axle housing was optimized in order to minimize its weight. It was expected that the decrease in weight would lead to improved fuel economy; in this work, the vehicle was simulated for the EPA highway drive cycle (HWFET) both before and after the optimization of the housing, in order to quantify the changes in fuel economy. It was found that the optimization of the housing did produce a modest improvement …

Autojack - Hydraulic Powertrain System, Tyce Vu

All Undergraduate Projects

A primary problem for mechanics and automotive enthusiasts is the risk associated with lifting and securing a vehicle with conventional jack stands. Often times, improper jack-stand installation results in the vehicle collapsing unexpectedly, causing injury and/or death. This problem can be minimized through the application of a newly re-designed vehicle lifting system. The conventional method for lifting cars is time consuming and can be unsafe in many circumstances. A better, safer, and more efficient lift design was needed; the AutoJack. The approach of the AutoJack design was entirely focused on the safety of lifting a vehicle. Safety was improved by …