Systems Engineering and Multidisciplinary Design Optimization Commons^™

Design And Implementation Of A Launching Method For Free To Oscillate Dynamic Stability Testing, Kristen M. Carey

Mechanical & Aerospace Engineering Theses & Dissertations

Magnetic Suspension and Balance Systems (MSBS) allow for static, forced oscillation and free to oscillate dynamic stability testing in a wind tunnel without the need for a physical support. The objectives of study are to assist in the application of the free to oscillate testing method in an MSBS to determine dynamic stability characteristics for various re-entry capsule designs.

This thesis discusses the development and testing of a launching method called the grabber for use in the MSBS Subsonic Wind Tunnel at NASA Langley Research Center. Aerodynamic tests were run to support the use of this method and compare the …

A Model-Based Systems Engineering Approach To E-Vtol Aircraft And Airspace Infrastructure Design For Urban Air Mobility, Heidi Selina Glaudel

Mechanical & Aerospace Engineering Theses & Dissertations

This paper serves to contribute to Model-Based Systems Engineering (MBSE) by following the NASA Systems Engineering Handbook framework for a Systems Engineering (SE) design approach to an Electric Vertical Takeoff and Landing (e-VTOL) aircraft and the incorporating airspace infrastructure. The focus of this study is, by using the MBSE model created, to capture the technical requirements definition and design intent of the vehicle and airspace inclusive of community specific knowledge derived from the Federal Aviation Administration (FAA) NextGen Urban Air Mobility (UAM) Concept of Operations (ConOps) version 1.0. The stakeholder requirements derived from the FAA UAM NextGen ConOps will form …

Model Based Systems Engineering For A Venture Class Launch Facility, Walter Mcgee Taraila

Mechanical & Aerospace Engineering Theses & Dissertations

A study of Model-Based Systems Engineering (MBSE) applied to a small-lift launch facility is presented. The research uses Systems Modeling Language (SysML) products and functional diagrams to document the structure, controls, electrical power, hydraulic, safety mechanisms, software, and fluid ground systems on a launch pad. The research is motivated by the need to design complex systems with an unambiguous understanding that improves communication, quality, productivity, and reduces risk. A model is developed following the ISO/IEC-15288 technical process framework. The stakeholder requirements are defined and analyzed to provide traceability to individual systems and subsystems. An architectural design is realized and implemented …

Control Design And Implementation For An Autonomous Surface Vehicle Using Azimuth Thrusters, Stanton James Coffey

Mechanical & Aerospace Engineering Theses & Dissertations

Autonomous Surface Vehicle research for water applications is inspired by a technological push to create more automated robotics that can perform functions too menial for a human to spend time on as well as too complex, difficult, or dangerous for a person to perform. The development objective is to construct, program, and test an autonomous surface vehicle that can perform precision hold maneuvers independent of human control. This capability would be useful in many situations where it is desirable to freeze the current position of the boat in order to perform some duty task. To conduct the research for this …

A Multi-Objective Differential Evolution Algorithm For Engineering Design Optimization, Shantanu S. Muluk

Mechanical & Aerospace Engineering Theses & Dissertations

The current research investigation focuses on the development of a multi-objective global optimizer based on the differential evolution algorithm. A rotationally invariant version of the original differential evolution algorithm is adopted as the core component of the optimization procedure. The optimizer is applied to a number of multi-objective problems: constrained problems, problems of high dimensionality, and problems with non-convex Pareto fronts.

The effectiveness of the proposed optimization framework in real engineering design problems is demonstrated by carrying out an aerodynamic shape optimization of wind turbine airfoils. The investigation focuses on both thin and thick airfoils. The produced Pareto-optimal airfoil shapes …

Multidisciplinary Design Optimization Of Transonic Airfoil Sections Using Multiobjective Optimization And Computational Intelligence Tools, Amit A. Kulkarni

Mechanical & Aerospace Engineering Theses & Dissertations

The design of transonic airfoils for civil aviation applications has been a major engineering challenge in the last fifty years. This design problem arises due to the need to limit shock wave drag at a given transonic speed. In recent years, the requirement to reduce the levels of aircraft noise has started to affect the airfoil design process. The multidisciplinary aerodynamic shape optimization problem is treated in this thesis using a multi-objective approach. The objectives correspond to the design of transonic airfoil sections with low drag during cruise and low trailing edge noise levels during the approach condition. The optimization …

A Design Of Experiments Approach To Deck Flow Characterization On An Aircraft Carrier, Yugapriya Sivanesan Wing

Mechanical & Aerospace Engineering Theses & Dissertations

A wind tunnel model of an aircraft carrier was used to make air wake measurements. Particle image velocimetry measurements of turbulence intensity were made on a center plane intersecting the angled deck of the aircraft carrier. The factors of interest for the study were model pitch, yaw, island location, and island type. Two island types were used, a representative shape of current designs and an ideal streamlined airfoil shape. Each factor was studied at two levels in order to provide linear models using a Design of Experiments factorial design. From the data for each experimental combination, regression models for turbulence …

Assessment Of Preliminary Design Approaches For Metallic Stiffened Cylindrical Shell Instability Problems, Vicki Owen Britt

Mechanical & Aerospace Engineering Theses & Dissertations

A preliminary design tool for metallic stiffened fuselage cylindrical panels subjected to longitudinal compression has been developed and validated by comparison to test results. Several methodologies for stiffened panel buckling and failure predictions were examined and evaluated. An appropriate level of analysis fidelity was determined for different failure modes and design details. Results from panel tests conducted to verify analytical methods used to design the Gulfstream V aircraft were presented. The panels were representative of four general skin/stringer configurations on the aircraft. Finite Element analyses and standard analytical methods were used to predict panel failure loads. The accuracy of the …

Most Probable Point-Based Design Optimization, Akhil R. Tipnis

Mechanical & Aerospace Engineering Theses & Dissertations

Modem products ranging from simple components to complex systems should be designed to be optimal and reliable. The challenge of modem engineering is to ensure that manufacturing costs are reduced and design cycle times are minimized while achieving requirements for performance and reliability. If the market for the product is competitive, improved quality and reliability can generate very strong competitive advantages. Reliability based design optimization plays a very important role in designing almost any kind of product. This investigation focuses on the development of the hybrid PMNRIA approach which uses the active-in-reliability concept for reliability based design optimization. The efficiency …

Optimal Aeroelastic Vehicle Sensor Placement For Root Migration Flight Control Applications, Abdul Ghafoor Al-Shenhabi

Mechanical & Aerospace Engineering Theses & Dissertations

An important step in control design for elastic systems is the determination of the number and location of control system components, namely sensors. The number and placement of sensors can be critical to the robust functioning of active control systems, especially when the system of interest is a large high-speed aeroelastic vehicle. The position of the sensors affects not only system stability, but also the performance of the closed-loop system. In this dissertation, a new approach for sensor placement in the integrated rigid and vibrational control of flexible aircraft structures is developed. Traditional rigid-body augmentation objectives are addressed indirectly through …

Setpoint Tracking Predictive Control In Chemical Processes Based On System Identification, Sinchai Chinvorarat

Mechanical & Aerospace Engineering Theses & Dissertations

A Kraft recovery boiler in a pulp-paper mill provides a means for recovery of the heat energy in spent liquor and recovery of inorganic chemicals while controlling emissions. These processes are carried out in a combined chemical recovery unit and steam boiler that is fired with concentrated black liquor and which produces molten smelt. Since the recovery boiler is considered to be an essential part of the pulp-paper mill in terms of energy resources, the performance of the recovery boiler has to be controlled to achieve the highest efficiency under unexpected disturbances.

This dissertation presents a new approach for combining …

Studies Related To The Design Of A Magnetic Suspension And Balance System For An Ultra-High Reynolds Number Flow Facility, Oscar Magno Michael Gomeiz

Mechanical & Aerospace Engineering Theses & Dissertations

The basic design principles for a magnetic suspension and balance system applied to the test section of an ultra-high Reynolds number facility are defined. The design of the cross-sectional area to be used in the test section is analyzed. The parameters of the permanent magnet to be used in the model inside the test section are investigated. The testing of magnetic fields at the center of a test pipe and validation of data by computer finite element analysis is described with the purpose of finding common results. The performance of the magnet configuration is evaluated with relation to the magnetic …

Design Optimization Of Magnetic Bearings And Magnetic Suspension Systems, V. Dale Bloodgood Jr.

Mechanical & Aerospace Engineering Theses & Dissertations

Magnetic suspension systems were first demonstrated as practical by Holmes and Beams in the 1930's. Since then, numerous academic researchers have worked with various types of these systems. Commercial applications have largely been limited to magnetic bearings for rotating machinery. Other applications that have held considerable promise include wind tunnel model suspensions, space payload pointing and vibration isolation systems, satellite momentum storage and control devices and electromagnetic launch systems. However, none of these have progressed significantly beyond the prototype stage. Maglev trains have not reached serious commercial service but are being aggressively developed in Germany and Japan.

Design methods for …

The Design And Testing Of An Inlet-Airfoil For A High Altitude Remotely Piloted Aircraft, Preston Bradley Martin

Mechanical & Aerospace Engineering Theses & Dissertations

The following work describes and validates a methodology for the aerodynamic design of a low drag, efficient inlet-airfoil to be used on the cooling installations of a high altitude remotely piloted aircraft. Owing to the primary aircraft design requirement of subsonic endurance at high altitude (85,000 ft), the flight conditions present an aerodynamically unfavorable combination of low chord Reynolds number (500,000) and high subsonic Mach number (0.5). At this flight condition, the inlet-airfoil must meet the heat exchanger cooling flow requirements while maintaining the aerodynamic performance of the airfoil. As a result, the design method is closely coupled with not …

Input Design For Systems Under Identification Using Indirect And Direct Methods, Marco P. Schoen

Mechanical & Aerospace Engineering Theses & Dissertations

The motivation for system identification can be manifold. In this work, the provocation to identify unknown system characteristics is derived from the control engineering point of view. That is, one intends to design a control strategy based on the identified system properties. The used system identification methods are the Open-Loop Kalman filter System Identification method (OKID) and the Closed-Loop System Identification method (CLID). It is shown that the quantitative largest error of the system identification is given by its model representation, that is the attempt to describe a system with model parameters which poses a linear relationship with the input/output …

An Approach For Multidisciplinary Design Optimization, Robert V. Krueger

Mechanical & Aerospace Engineering Theses & Dissertations

Multidisciplinary Design Optimization (MDO) is an optimization technique that allows complex designs to be improved by managing conflicting goals in such a fashion so as to improve the overall design. This thesis presents a nonhierarchic MDO formulation and gives a general explanation of how it is to be applied to various appropriate problems. In addition, this thesis evaluates the viability of this MDO technique by applying it to two distinct, multidisciplinary problems that have been used as examples in other literature. The first example problem is a combined aerodynamic/structural problem and the second example is an alkylation process problem. First, …

Theoretical Results Supporting The Use Of Passive Damping As Augmentation To The Active Control Of Flexible Structures, Joseph Vincent Harrell

Mechanical & Aerospace Engineering Theses & Dissertations

One challenge of modern control technology is how to control a flexible structure with accuracy, speed, and economy of effort. Controlling a structure with many degrees of freedom by purely active means implies the implementation of inordinate sensors and actuators and creates the need for numerous calculations that must be done instantly. Experiments have shown that practical structures under active control alone can suffer instabilities due to modal vibrations beyond the bandwidth of the active controller. Furthermore, if there is a high degree of model uncertainty, instabilities can be produced by inputs of modal vibrations not occurring in the system …

Maximum Likelihood Estimation For Distributed Parameter Models Of Large Beam-Like Structures, Ji Yao Shen

Mechanical & Aerospace Engineering Theses & Dissertations

Proposed large space structures have many characteristics that give an advantage to modeling their structural dynamics by a set of partial differential equations (PDE's). By far, the most effort put forth in studying system identification and control to date has been based on finite element models. Despite its acceptability, such lumped parameter models have inevitable deficiencies primarily because of their complexity. Both approaches are complementary and each should be used where it is most effective. But the fact is that the distributed parameter approach has not been developed to the level of maturity as for the lumped parameter approach.

Motivated …

Eigensensitivity Analysis For Space Structures With Applications In Design Optimization, Sean Patrick Kenny

Mechanical & Aerospace Engineering Theses & Dissertations

Eigensensitivity analysis is concerned with the rates of changes of eigenvalues and eigenvectors with respect to design variables. Eigensolutions of space structures are found to display four distinct characteristics, three of which are related to various types of repeated eigenvalues. This study will address three cases of the real symmetric structural eigenvalue problem. The three cases that will be considered are: distinct eigenvalues, repeated eigenvalues with distinct first eigenvalue derivatives, and repeated eigenvalues with infinitely repeating eigenvalue derivatives. Analytic formulations for eigenvalue/ vector derivatives will be presented for each of the three cases. The directional differentiability of eigenvalues for the …