Systems Engineering and Multidisciplinary Design Optimization Commons^™

Simulation-To-Hardware Validation Of Mpc For Binary Thruster 2d Cubesat Control, Aevar Amundinusarson Oefjoerd

Theses and Dissertations--Mechanical and Aerospace Engineering

Small satellites must execute precise, fuel-limited maneuvers under strict actuation and operational constraints. Model Predictive Control (MPC) is a suitable approach because it optimizes future actions while explicitly enforcing these limits. This work evaluates (1) whether MPC can operate in real time using binary (on/off), asymmetric thrusters, and (2) whether a high-fidelity digital twin can be used to tune and validate the controller prior to hardware testing.

An MPC framework was implemented on a planar satellite prototype that floats on air bearings, operates at 16.7 Hz (60 ms period), and uses eight binary thrusters exhibiting up to 13.2% variation in …

Kentucky Re-Entry Universal Payload System (Krups): Hypersonic Re-Entry Flight, John Daniel Schmidt

Theses and Dissertations--Mechanical and Aerospace Engineering

The Kentucky Re-entry Universal Payload System (KRUPS) is a small capsule designed as a technology testbed for re-entry experiments. For its first incarnation, KRUPS has been designed to test Thermal Protection Systems (TPS) and instruments in re-entry flights. Because of the unique environment a vehicle undergoes during re-entry, there is a high-demand for experimental data from re-entry experiments. KRUPS has been developed at the University of Kentucky (UK) over the past seven years to meet this demand. After completing sub-orbital campaigns, the first KRUPS hypersonic re-entry mission was attempted. The mission involved building three 11-inch diameter capsules each outfitted with …

Data-Driven Tools Guided By First-Principles For Scale Modeling, Sadegh Poozesh

Progress in Scale Modeling, an International Journal

For decades, traditional scale-modeling techniques have been relying on first-principles models (FPMs). FPMs have been used to find non-dimensional numbers (PIs) and identify normalized underlying forces and energies behind the phenomenon in focus. The two main challenges with FPM-based PIs extraction are finding the relevant PIs and proper correlations between PIs. The emergence and surge of data-driven modeling (DDM) provide a new opportunity to leverage experimental data in model development across scales/plants. In this paper, first, the two mentioned issues in PIs development will be elaborated to reveal the gap, and second, a new insight into scale modeling and similarity …

The Kentucky Re-Entry Universal Payload System (Krups): Orbital Flight, James Tyler Nichols

Theses and Dissertations--Mechanical and Aerospace Engineering

Due to the uniqueness of atmospheric entry environments, ground facilities cannot accurately replicate re-entry conditions. Consequently, scientists primarily rely on numerical models to predict these conditions and inform Thermal Protection System (TPS) designs. These models often lack flight validation, which is necessary for increasing their fidelity. Thus, there is a substantial need to obtain such data to advance modeling capabilities.

The Kentucky Re-entry Universal Payload System (KRUPS) is an adaptable test-bed for scientific experimentation with initial application to TPS. This vehicle was designed at the University of Kentucky to serve as an inexpensive means of obtaining validation data to enhance …

Structural Optimization Of Space Transit Vehicle Concept, Hercules, James Philip Rogers

Theses and Dissertations--Mechanical and Aerospace Engineering

STRUCTURAL OPTIMIZATION OF SPACE TRANSIT VEHICLE CONCEPT, HERCULES:

A COMPARATIVE STUDY OF STRUCTURAL OPTIONS

Hercules is a vehicle concept developed by NASA Langley's Vehicle Analysis Branch to satisfy the need for sustainable transit between Earth, the moon, and Mars. Hercules features unprecedented abort capabilities and mission flexibility to aid in NASA's Mars campaign. By utilizing modern software to perform structural analysis and optimization for a large selection of stiffened panel concepts, beam concepts, and materials trends in the structural optimization emerge. These trends will be invaluable for the design of future spacecraft needed to fulfill similar roles.

The structural optimization …

Atv Dynamics And Pediatric Rider Safety, James T. Auxier Ii

Theses and Dissertations--Biomedical Engineering

It has been observed through numerous academic and governmental agency studies that pediatric all-terrain vehicle ridership carries significant risk of injury and death. While no doubt valuable to safety, the post-hoc approach employed in these studies does little to explain the why and how behind the risk factors. Furthermore, there has been no prolonged, widespread, organized, and concerted effort to reconstruct and catalog the details and causes of the large (20,000+) number of ATV-related injuries that occur each year as has been done for road-based motor vehicle accidents. This dissertation takes the opposite approach from a meta-analysis and instead examines …

Design Process For The Containment And Manipulation Of Liquids In Microgravity, Chris Meek

Theses and Dissertations--Mechanical and Aerospace Engineering

In order to enhance accessibility to microgravity research, the design process for experiments on the ISS must be streamlined and accessible to all scientific disciplines, not just aerospace engineers. Thus, a general design and analysis toolbox with accompanying best practices manual for microgravity liquid containment is proposed. The work presented in this thesis improves the design process by introducing a modular liquid tank design which can be filled, drained, or act as a passive liquid-gas separation device. It can also be pressurized, and used for aerosol spray. This tank can be modified to meet the design requirements of various experimental …

Considerations For Atmospheric Measurements With Small Unmanned Aircraft Systems, Jamey D. Jacob, Phillip B. Chilson, Adam L. Houston, Suzanne Weaver Smith

Mechanical Engineering Faculty Publications

This paper discusses results of the CLOUD-MAP (Collaboration Leading Operational UAS Development for Meteorology and Atmospheric Physics) project dedicated to developing, fielding, and evaluating integrated small unmanned aircraft systems (sUAS) for enhanced atmospheric physics measurements. The project team includes atmospheric scientists, meteorologists, engineers, computer scientists, geographers, and chemists necessary to evaluate the needs and develop the advanced sensing and imaging, robust autonomous navigation, enhanced data communication, and data management capabilities required to use sUAS in atmospheric physics. Annual integrated evaluation of the systems in coordinated field tests are being used to validate sensor performance while integrated into various sUAS platforms. …

Inkjet Printing: Facing Challenges And Its New Applications In Coating Industry, Sadegh Poozesh

Theses and Dissertations--Mechanical and Aerospace Engineering

This study is devoted to some of the most important issues for advancing inkjet printing for possible application in the coating industry with a focus on piezoelectric droplet on demand (DOD) inkjet technology. Current problems, as embodied in liquid filament breakup along with satellite droplet formation and reduction in droplet sizes, are discussed and then potential solutions identified. For satellite droplets, it is shown that liquid filament break-up behavior can be predicted by using a combination of two pi-numbers, including the Weber number, We and the Ohnesorge number, Oh, or the Reynolds number, Re, and the Weber number, …

Numerical Modeling And Characterization Of Vertically Aligned Carbon Nanotube Arrays, Johnson Joseph

Theses and Dissertations--Mechanical and Aerospace Engineering

Since their discoveries, carbon nanotubes have been widely studied, but mostly in the forms of 1D individual carbon nanotube (CNT). From practical application point of view, it is highly desirable to produce carbon nanotubes in large scales. This has resulted in a new class of carbon nanotube material, called the vertically aligned carbon nanotube arrays (VA-CNTs). To date, our ability to design and model this complex material is still limited. The classical molecular mechanics methods used to model individual CNTs are not applicable to the modeling of VA-CNT structures due to the significant computational efforts required. This research is to …