Systems Engineering and Multidisciplinary Design Optimization Commons^™

Design And Realization Of An Unmanned Aerial Rotorcraft Vehicle Using Pressurized Inflatable Structure, Nirmal Sadasivan

International Journal of Aviation, Aeronautics, and Aerospace

Unmanned aerial rotorcraft vehicles have many military, commercial and civil applications. There is a necessity to advance the performance on several ranges of rotorcraft for using these vehicles successfully in the expanded future roles. A lower flight time, noise disturbance and safety issues remain the key obstacles in increasing the efficiency of the rotorcraft for various applications. This work presents the design and realization of a rotorcraft using pressurized inflatable structure filled with lighter than air gas such as helium or hydrogen to provide lift assistance for the vehicle. Two iterative design procedures were developed for designing the vehicle. One …

Dual Graphene Patch Antenna For Ka Band Satellite Applications, Mohammed Amin Rabah, Mohammed Bekhti

International Journal of Aviation, Aeronautics, and Aerospace

Currently; grapheme offers a new opportunity to use in space technology and this is due to its amazing properties like conductivity, strength, flexibility and transparency which allows us to exploit new generation of ultra-fast nanoscale components; Since future wireless communication techniques are geared towards the use of the high frequency spectrum and many recent research prove this trend. This letter presents a proposal for design of a dual graphene-based antenna to use in new communication techniques in Ka band, where the proposed antenna can work for uplink and dowlink frequencies at same time since it has return loss less then …

Determination Of Takeoff And Landing Distances Using An Ipad Performance Application For The Diamond Da40, Tyler A. Babb, Christina Hiers

International Journal of Aviation, Aeronautics, and Aerospace

All pilots are required to calculate aircraft performance parameters prior to flight. This includes takeoff and landing distances. Traditionally, pilots in training have planned for takeoff and landing performance using paper charts provided by the manufacturer. However, professional pilots use devices such as Flight Management Systems (FMS), Electronic Flight Bag (EFB) applications, or on-board performance computers (OPC) to make such calculations. During primary flight training, student pilots could make performance calculations with proper software, similar to the method they will typically use at the professional level. Recently an iPad application was released which can calculate numerous performance parameters for specific …

Subjectivity In Failure Mode Effects Analysis (Fmea) Severity Classification Within A Reliability Centered Maintenance (Rcm) Context, Marc Banghart, Kari Babski-Reeves, Linkan Bian, Lesley Strawderman

International Journal of Aviation, Aeronautics, and Aerospace

This research paper investigated subjectivity in the severity rating of failure modes within a risk analysis process. Although several risk analysis processes can be utilized, the study considered the application of Failure Modes Effects Analysis (FMEA) or Failure Modes Effects and Criticality Analysis (FMECA) due to its common use within the Aerospace Industry. The study investigated both differences in severity selection given varying amounts of experience as well as any association between severity selection and the provided input information. The main goal of the research was to investigate the impact of data quality on severity selection and to identify factors …

Responsible Behavior For Constellations And Clusters, Darren Mcknight, Jonathan Rosenblatt, Darren Garber

Space Traffic Management Conference

Many large constellations are being considered for deployment over the next ten years into low earth orbit (LEO). This paper seeks to quantify the risks that these constellations pose to the debris environment, the risks that the debris environment poses to these constellations, and the risks that these constellations pose to themselves. The three representative constellations examined in detail in this paper are operated (or planned to be operated) by Spire Global, Iridium, and OneWeb. This paper provides a balanced risk analysis including collision risk, operational risk, and non-adherence risk. For perspective, the risk posed by these economically useful constellations …

Design And Optimization Of Aircraft Configuration For Minimum Drag, Zin Win Thu, Aung Myo Thu, Phyo Wai Thaw

International Journal of Aviation, Aeronautics, and Aerospace

This paper presents a reliable and robust optimization for minimum drag of an aircraft at the conceptual design phase. Firstly, the conceptual design code was developed and existing Single Seat Aerobatic (SSA) aircraft was chosen to validate the reliability of developed code. The resulted data from the developed code showed good agreement with the existing data. Secondly, Sequential Quadratic Programming (SQP) optimizer was created and employed as a tool to explore possible aircraft configurations that are more efficient and less costly than an existing design. The optimized results gave lower Drag and better performance.

Design Of Revising Proximity Between Space And Time Cues On Flight Deck Displays To Support Nextgen – The First Phase, Chang-Geun Oh, Jennie J. Gallimore, Pamela S. Tsang

International Journal of Aviation, Aeronautics, and Aerospace

The objective of this study is to develop and evaluate novel display formats to support RTA operations for near to midterm NextGen. Traditional cockpit displays separate space and time information in distant display sources in heterogeneous formats (graphics vs. text). This design composition may cause potential pilot errors when required time of arrival (RTA) obligations are imposed at every waypoint in NextGen. Pilots were randomly assigned to four different display conditions in a simulator – one traditional display with distant space and time cues, and three novel displays with close spatial proximity between the two cues. In the first phase …

Design Of Revising Proximity Between Space And Time Cues On Flight Deck Displays To Support Nextgen – The Second Phase, Chang-Geun Oh, Jennie J. Gallimore, Pamela S. Tsang

International Journal of Aviation, Aeronautics, and Aerospace

The prior first phase of this study investigated the effectiveness of new design of flight deck display for required time of arrival operation of NextGen by collecting objective query response data during autopilot flights and subjective data about the perception between display condition and situation awareness level. To evaluate pilots’ mental workload during the operations when they interacted with novel flight deck display design, this second phase provided pilots with simulation flight tasks arriving at four successive waypoints on time in the same display conditions as the first phase and asked them to rate their mental workload ratings. The workload …

Blended Wing Body Propulsion System Design, Parth Kumar, Adeel Khalid

International Journal of Aviation, Aeronautics, and Aerospace

This research paper focuses on the optimization of the propulsion system of a blended wing body design. Two different aspects of the design, the engine placement and count, and the engine itself, are investigated. The preliminary wing of the BWB is created through aerodynamic analysis, and is kept as a constant over the different propulsion system configurations. The engine parameters are first investigated. Equations are derived to express takeoff distance and climb rate as a function of engine sea level thrust, cruise thrust, and the number of engines. Nearly 150 different engine models, in BWB configurations of 2, 3, 4, …

Time Optimal State Feedback Control With Application To A Spacecraft With Cold Gas Propulsion, Samuel J. Kitchen-Mckinley, Sergey V. Drakunov

Publications

A cold gas propulsion system is well suited to provide the required thrust for a small surveyor spacecraft operated near an asteroid or planetary surface. The cold gas propellant can obtained in-situ from local surface or atmospheric constituents. For small spacecraft, the cold gas system may be limited to only on-off control of the main tank where the generated thrust is directly dependent on the tank pressure. As such the thrust will slowly decrease as the propellant is expended. A state feedback, time optimal, control law is developed for a vehicle with propellant is expended. A state feedback, time optimal, …

Cruise Missile Integrated Air Defense System Penetration: Modeling The S-400 System, Michael Pelosi, Amie K. Honeycutt

International Journal of Aviation, Aeronautics, and Aerospace

This research determines improved flight-path routes that make maximum utilization of terrain-masking opportunities, and defending radar and missile system equipment performance and launch timing constraints, in order to avoid radar detection and tracking, and to mitigate subsequent missile shoot-down risks. The problem is formulated as one of constrained optimization in three dimensions. Advantageous solutions are identified using the A* Algorithm in conjunction with detailed equipment performance and constraint calculations and high-resolution digital terrain elevation maps. Topographical features in digital terrain are exploited by the algorithm to avoid radar detection and tracking. The model includes provisions for all-aspect/all-frequency radar cross section …

Professional Pilot Commercial Off-The-Shelf (Cots) Efb Usage, Policies And Reliability, Tyler A. Babb

International Journal of Aviation, Aeronautics, and Aerospace

Electronic Flight Bags (EFBs) have flooded the aviation industry. Commercial off-the-shelf (COTS) tablets are now commonly used by pilots as EFBs. Operators use EFBs for ease of use, faster access to information, to remove weight from the aircraft, and to increase pilots’ quality of life. Identifying trends in EFB usage among professional pilots could benefit operators and universities with flight training programs. EFB policies and procedures may vary among operators but achieve FAA compliance. This study identified these policies and procedures. The types of devices and software vary, and identifying these devices and software could be useful. This research used …

Development Of Fault Tolerant Adaptive Control Laws For Aerospace Systems, Andres E. Perez Rocha

Doctoral Dissertations and Master's Theses

The main topic of this dissertation is the design, development and implementation of intelligent adaptive control techniques designed to maintain healthy performance of aerospace systems subjected to malfunctions, external parameter changes and/or unmodeled dynamics. The dissertation is focused on the development of novel adaptive control configurations that rely on non-linear functions that appear in the immune system of living organisms as main source of adaptation. One of the main goals of this dissertation is to demonstrate that these novel adaptive control architectures are able to improve overall performance and protect the system while reducing control effort and maintaining adequate operation …

Examining Time To Evacuate Dynamically Activated Aircraft Hazard Areas, Zheng Tao, Granghuai Wang, Ashley G. Williams, Jon L. Semanek, Jonathan L. Schwartz

Space Traffic Management Conference

The growth in launch and reentry operations in the National Airspace System (NAS) presents the Federal Aviation Administration (FAA) with the challenge of integrating them more efficiently while also minimizing effects on other NAS users and maintaining safety. Currently, to maintain safety and account for unforeseen events such as vehicle breakup, the FAA segregates large amounts of airspace, called Aircraft Hazard Areas (AHAs), from traditional NAS users during launch and reentry operations. In order to minimize effects on NAS users, some AHAs during reentry are dynamically activated only if an unexpected event occurs. If a dynamic AHA is activated, then …

From Xst To F-117a, Alan Brown

ERAU Prescott Aviation History Program

Learn the remarkable story of stealth technology from the man often referred to as “Mr. Stealth.” From 1975-1989 Alan Brown was a member of Lockheed “Skunk Works”, becoming program manager & chief engineer for the F-117A Stealth Fighter from initial concept until the first production aircraft was built, 1978 to 1982. Hear the inside story of the many challenges faced by the stealth program and how they were solved.

Standardization Of Human-Computer-Interface For Geo-Fencing In Small Unmanned Aircraft Systems, David Thirtyacre, Robert Brents, Michael Goldfein, David Hunter, B. Terwilliger

Publications

The use of small unmanned aircraft systems (sUAS) has increased significantly in the past year. Geographic fencing (geo-fencing) is software built into most medium-cost consumer sUAS. This software is typically used to limit the altitude above launch point, the flight distance from the transmitting controller, and/or restrict flight inside a no-fly zone. While the concept of a geo-fence is simplistic, the human-computer-interface (HCI) varies drastically among platforms, and even between software iterations on the same platform. This research examines the HCI of three popular consumer-level sUAS with regard to geo-fencing. The software procedures and human interface for the DJI Inspire-1, …

Designing A Mobile Space Habitat Analog, Victor Kitmanyen, Matthew Burkhard, Timothy Disher

Human Factors and Applied Psychology Student Conference

No abstract provided.

Space Data Integrator (Sdi) And Space Program Integrated Data And Estimated Risk (Spider): Proof-Of-Concept Software Solution For Integrating Launch And Reentry Vehicles Into The National Airspace System (Nas), Devin D. Dickens

Space Traffic Management Conference

The Space Data Integrator (SDI) Project is the initial step to satisfy the Federal Aviation Administration (FAA) strategic initiative to integrate commercial space launch and reentry vehicles into the National Airspace System. The project addresses the needs for greater situational awareness and monitoring, and increased response capability during non-nominal and catastrophic incidents during space operations.

The initial phase of this project leverages current FAA systems, and provide an initial demonstration of capability that will provide for state data from a commercial reentry vehicle to be ingested into a the FAA Traffic Flow Management System, and displayed on Traffic Situation Displays. …

Low Fidelity Flight Simulation In Collegiate Aviation, Vladimir N. Risukhin

Aviation / Aeronautics / Aerospace International Research Conference

Aviation college pilot training programs, lessons and exercises contain portions that do not require training in sophisticated and highly expensive full flight simulators and flight training devices (FTD) with high fidelity of simulation, or in real aircraft flights. Relatively inexpensive personal-computer-based flight simulation facilities named low fidelity simulators (LFS) can boost development of aircraft pilots’ cognitive and behavioral skills. The paper attempts to reveal how the LFS can support aviation college flight training and research activities. In the Western Michigan University College of Aviation, peer mentoring technique proven to be helpful in higher education institutions has been applied to flight …

Achieving Global Range In Future Subsonic And Supersonic Airplanes, Nihad E. Daidzic Ph.D., Sc.D.

International Journal of Aviation, Aeronautics, and Aerospace

No commercial airplane in service today is able to fly half great-circle distances over the globe and achieve the non-stop or the global range to any antipodal location on Earth. A subsonic jetliner has the optimum cruising speed at Mach numbers approaching the drag divergence Mach number while still preserving relatively high aerodynamic efficiency. Various fuel-flow laws were used to investigate the cruise performance of subsonic and supersonic aircraft. The effect of wind and aircraft weight and how it affects the optimal cruising airspeed was investigated. Of all different operational cruising techniques, the cruise-climb at high Mach numbers is the …

Preliminary Design Of Blade And Disc Fixing For Aerospace Application Using Multi-Disciplinary Approach, Abdulhalim Twahir

Doctoral Dissertations and Master's Theses

The preliminary design phase of a turbine rotor has an important impact on the architecture of a new engine definition, as it sets the technical envelope of the product to be designed. Additionally, preliminary design cycle times are increasingly critical in capturing business opportunities in an ever competitive environment. Improving the accuracy of the preliminary design (pre-detailed design) is also necessary as not only does it significantly reduce the overall development of an engine, but also because any mistakes made at this stage can be extremely hard to rectify.

Previously, typical pre-detail fixing design cycle time was greater due to …

Fluid-Structure Interaction And Multidisciplinary Design Analysis Optimization Of Composite Wind Turbine Blade, Naishadh G. Vasjaliya

Doctoral Dissertations and Master's Theses

A multidisciplinary design analysis optimization (MDAO) process is defined for a composite wind turbine blade to optimize its aerodynamic and structural performance by developing a fluid-structural interaction (FSI) system. The objectives are to maximize aerodynamic efficiency and structural robustness while reducing blade mass and total cost. In the previous research, a MDO process of a composite wind turbine blade has been pioneered as an effective process to develop structurally optimized blade design. Present MDAO process is defined in conjunction with structural and aerodynamic performance of the blade which is divided into three steps and the design variables considered are related …

Defining An Abrasion Index For Lunar Surface Systems As A Function Of Dust Interaction Modes And Variable Concentration Zones, Ryan L. Kobrick, David M. Klaus, Kenneth W. Street Jr.

Publications

Unexpected issues were encountered during the Apollo era of lunar exploration due to detrimental abrasion of materials upon exposure to the fine-grained, irregular shaped dust on the surface of the Moon. For critical design features involving contact with the lunar surface and for astronaut safety concerns, operational concepts and dust tolerance must be considered in the early phases of mission planning. To systematically define material selection criteria, dust interaction can be characterized by two-body or three-body abrasion testing, and sub-categorically by physical interactions of compression, rolling, sliding and bending representing specific applications within the system. Two-body abrasion occurs when a …

Scan Loss Pattern Synthesis For Adaptive Array Ground Stations, William C. Barott, Mary Ann Ingram, Paul G. Steffes

Publications

We present several techniques for maximizing the contact time between low Earth orbiting satellites (LEOs) and a ground station (GS). The GS comprises an adaptive array of electronically steered space-fed lenses (SFLs). Each SFL is manufactured as a low-cost printed circuit with the result that it exhibits scanning loss. By differently orienting the boresights of the SFLs in the adaptive array, the SFL's scanning losses can be made to optimally complement the path loss of the LEO, thereby reducing the cost of the GS while maximizing the download capacity of the satellite link. The optimization, implemented with a genetic algorithm …

Grating Lobe Reduction In Aperiodic Linear Arrays Of Physically Large Antennas, William C. Barott, Paul G. Steffes

Publications

We present performance bounds obtained from the optimization of the sidelobe levels of aperiodic linear arrays. The antennas comprising these arrays are large compared to the distance between neighboring antennas, a case not addressed in previously published work. This optimization is performed in pattern-space and is applicable over a wide range of scan angles. We show that grating lobes can be suppressed even when the elemental antennas are several wavelengths in size, provided that the ratio of the antenna size to the average spacing between the antenna center-points does not exceed 80%.

A Technology Survey Of Emergency Recovery And Flight Termination Systems For Uas, Richard Stansbury, Wesley Tanis, Timothy Wilson

Publications

For safe flight in the National Airspace System (NAS), either under the current interim rules or under anticipated longer-term regulatory guidelines facilitating unmanned aircraft system (UAS) access to the NAS, the UAS must incorporate technologies and flight procedures to ensure that neither people nor property in the air, on the ground, or on or in the water are endangered by the failure of an onboard component, by inappropriate unmanned aircraft (UA) response to pilot commands, or by inadvertent entry by the UA into prohibited airspace. The aircraft must be equipped with emergency recovery (ER) procedures and technologies that ensure that …

Development Of Automatic Cfd Grid Generation For The Design Of The Preliminary Wing Sweep Schedule For The Gulfstream Quiet Supersonic Jet, Ali Kazeneh

Master's Theses - Daytona Beach

The wing sweep schedule for the Gulfstream Quiet Supersonic Jet (wing and body) was investigated using CFD analysis methods. The use of automating the gridding procedure allowed for numerous cases to be investigated. The examination of the drag polar for different Mach cases indicated the optimum corresponding wing sweep position. The study results revealed that for the Mach 0.85 case, the wings should remain at the forward most pivoted position (Ʌ=25°). The Mach 1.1 case indicted that the wings should be in the fully swept back position (Ʌ=60°). The majority of the wing sweep transition occurs from Mach 0.85 to …

Innovative Schematic Concept Analysis For A Space Suit Portable Life Support Subsystem, M. Schuller, R. Kobrick, T. Lalk, L. Wiseman, F. Little, Et Al.

Publications

Conceptual designs for a space suit Personal Life Support Subsystem (PLSS) were developed and assessed to determine if upgrading the system using new, emerging, or projected technologies to fulfill basic functions would result in mass, volume, or performance improvements. Technologies were identified to satisfy each of the functions of the PLSS in three environments (zero-g, Lunar, and Martian) and in three time frames (2006, 2010, and 2020). The viability of candidate technologies was evaluated using evaluation criteria such as safety, technology readiness, and reliability. System concepts (schematics) were developed for combinations of time frame and environment by assigning specific technologies …

Aeroelastic Analysis Of A Flexible Membrane Wing, Isaac Nguri Wanjohi

Master's Theses - Daytona Beach

The focus of this research proposal is the investigation of the aeroelastic effects of a flexible lift augmentation system (LAS) wing. This research involves characterization of the forced vibration response of a wing appendage used to augment short field take off and landing (STOL) operations.

Although flutter theory is now well understood, the LAS presents the complications of a highly deformable airfoil shape as well as larger structural damping values compared to metal wings.

The proposed research will involve derivation of the equations of motion aided by experimental data from nodal excitation of the wing; stiffness and rigidity modeling from …

Modeling Launch Vehicle Success Using Artificial Neural Networks, Jennifer A. Schuck

Master's Theses - Daytona Beach

Expendable launch vehicles in the United States currently have a reliability of 92%. The failures that do occur cost millions of dollars in spacecraft replacement, lost revenue, and other expenses. These costs are passed on in higher insurance rates and launch vehicle price. If the launch outcome of the launch vehicles could be better predicted, the overall cost of launching payloads into space would decrease. This study used artificial neural networks to model the overall launch outcome of a launch vehicle so that the results of a launch could be predicted. Two neural network architectures--MLP and fuzzy ARTMAP--were trained on …