Systems Engineering and Multidisciplinary Design Optimization Commons^™

System Integration And Validation Of The Cal Poly Spacecraft Attitude Dynamics Simulator Mk. Iv, Bricen S. Rigby

Master's Theses

The Cal Poly Spacecraft Attitude Dynamics Simulator (SADS) is an ongoing project that seeks to enable the simulation and validation of sensors, actuators, and control logic related to spacecraft attitude control. The SADS platform rests atop a spher- ical air-bearing device which allows for nearly frictionless rotation in all three axes. The orientation of the platform is controlled by four reaction wheels arranged in a pyramidal configuration. Over the past few years, there have been significant updates to the reaction wheel subsystem, as well as requests for a more capable central com- puter. Therefore, a new system architecture for the …

Flexible Fault-Tolerant Multi-Die Fpga-Based Architectures For Varying Space Environments, Yosof Ali Seif El Din Ali Maklad

Theses and Dissertations

It is well-known fact that spacecraft’s electronic components operate in an extreme harsh and varying space environments, beside changing orbit or passing through Van Allan Belts during orbital course results of radiation levels change. This thesis focuses on SRAM-based FPGA systems on-board of such spacecrafts, that are commonly utilized in space applications’ critical applications due to their capabilities and flexibility to reconfigure, since these systems are vulnerable to frequent negative impacts of ionizing radiation, thus inducing soft and hard errors leading to disastrous failures that could jeopardize the entire spacecraft. The soft errors’ effects are frequent yet can be mitigated, …

Wind Tunnel Instrumentation And Testing, Nicholas Marek, Abraham Mezera, Laura Jin, Hayden Smith, Curtis Cook

Student Scholar Symposium

The Raymond B. Jones College of Engineering was contacted by an automotive engineering firm seeking to use the college’s wind tunnel for gathering data on the aerodynamic performance of a proprietary prototype automotive door. Specifically, the client requested the quantification of the drag coefficient of the model at extreme wind speeds. The drag coefficient, a dimensionless number that quantifies the resistance of a specific geometric shape to airflow, will be a valuable datapoint for the client’s design iteration. Due to the sensitive nature of their work, the client has wished to remain anonymous. RBJCOE professors tasked a senior design team …

Development Of A Cost-Effective Daq For Measuring Brake Performance In Race Cars, Adrin Alias

2025 Spring Honors Capstone Projects - Archive

This project explores the feasibility of creating a cost-effective data acquisition (DAQ) system for high-speed, real-time brake performance testing of Formula SAE racecars. The research addresses the limitations of the current MoTeC DAQ system currently employed by the team, which is costly and time-consuming to set up for on-car testing. The team will use a brake dynamometer for steady-state comparisons of different brake pad compounds (senior design project), but evaluating real-world performance requires on-car testing. By systematically comparing various hardware platforms, sensors, communication protocols, and storage solutions, this project aims to balance cost-efficiency with reliability and performance. The research evaluates …

Production Box Cost Estimating Relationships For Dod Avionics, Carla J. Cisneros, Edward D. White, Brandon M. Lucas, Jonathan D. Ritschel, Robert D. Fass, Shawn M. Valentine

Faculty Publications

The authors use historical information obtained from the Cost Assessment Data Enterprise to estimate recurring production unit cost for DoD avionics via cost estimating relationships (CERs). The specific modeled responses include mean unit cost, median unit cost, and the 100th production unit cost (T100) utilizing learning curve theory. For T100, the authors adopt both a multiplicative and an additive error for CER comparison. Recommended CERs consist of the mean unit cost and the T100 utilizing a multiplicative error. Moreover, results reveal that weight has a significant effect on cost as well as a potential underaccounting of real price change or …

Design Of A Launchable Remote-Controlled Rover And Protective Aeroshell, Matthew Loewer, Colby Weeks, Lake Williams, Jackson Zazzaro

Senior Theses

Planetary rovers, vehicles that can traverse challenging terrain, have excelled in their exploration missions to other celestial bodies. They have been especially suitable for exploring Mars, as rovers such as Opportunity and Perseverance have collected valuable geological, atmospheric, seismic, and magnetic information from the Martian surface. Rovers will remain vital in future space exploration missions, and it is necessary to understand their design and functionality. This paper focuses on the design and prototyping of a miniature rover that can survive the rough Martian terrain while collecting and submitting environmental data for scientific analysis. The design is based off proven Martian …

Crazyflie 2.1 Quadcopter Nonlinear System Identification, Nhat V. Nguyen, Hope Storro, John Plimpton

2023 Symposium

Quadcopters (quad) are used widely in many industries with crucial applications such as infrastructure inspection or package delivery. The Crazyflie 2.1 quad from Bitcraze provides an excellent platform for research and development. In this project, our goal is to perform system identification on the Crazyflie to propose a complete model. A gray box method is explored, which includes leveraging the parameters that are already known, to develop a set of equations. Through theory, simulations, and measurements, a complete quadcopter model is developed.

Assessing The Performance Of A Particle Swarm Optimization Mobility Algorithm In A Hybrid Wi-Fi/Lora Flying Ad Hoc Network, William David Paredes

UNF Graduate Theses and Dissertations

Research on Flying Ad-Hoc Networks (FANETs) has increased due to the availability of Unmanned Aerial Vehicles (UAVs) and the electronic components that control and connect them. Many applications, such as 3D mapping, construction inspection, or emergency response operations could benefit from an application and adaptation of swarm intelligence-based deployments of multiple UAVs. Such groups of cooperating UAVs, through the use of local rules, could be seen as network nodes establishing an ad-hoc network for communication purposes.

One FANET application is to provide communication coverage over an area where communication infrastructure is unavailable. A crucial part of a FANET implementation is …

Monte-Carlo-Based Analysis Of Traffic Flow For Urban Air Mobility Vehicles, Sara Ghayouraneh

Graduate Theses and Dissertations

The research conducted in this dissertation is focused on developing a simulation tool that can predict the traffic flow patterns of the Urban Air Mobility vehicles to alleviate some of the challenges related to their traffic management. First, an introduction to the concept of Urban Air Mobility is given, the usage of Automatic Dependent Surveillance-Broadcast systems for Urban Air Mobility vehicles is suggested and dynamic addressing concept is introduced as an answer to a part of air traffic management and address scarcity challenge for Urban air Mobility vehicles. Next, in order to simulate the traffic flow patterns of the Urban …

Nonlinear Least Squares 3-D Geolocation Solutions Using Time Differences Of Arrival, Michael V. Bredemann

Mathematics & Statistics ETDs

This thesis uses a geometric approach to derive and solve nonlinear least squares minimization problems to geolocate a signal source in three dimensions using time differences of arrival at multiple sensor locations. There is no restriction on the maximum number of sensors used. Residual errors reach the numerical limits of machine precision. Symmetric sensor orientations are found that prevent closed form solutions of source locations lying within the null space. Maximum uncertainties in relative sensor positions and time difference of arrivals, required to locate a source within a maximum specified error, are found from these results. Examples illustrate potential requirements …

Developing A Uas-Deployable Methane Sensor Using Low-Cost Modular Open-Source Components, Gavin Demali

Williams Honors College, Honors Research Projects

This project aimed to develop a methane sensor for deployment on an unmanned aerial system (UAS), or drone, platform. This design is centered around low cost, commercially available modular hardware components and open source software libraries. Once successfully developed, this system was deployed at the Bath Nature Preserve in Bath Township, Summit County Ohio in order to detect any potential on site fugitive methane emissions in the vicinity of the oil and gas infrastructure present. The deliverables of this project (i.e. the data collected at BNP) will be given to the land managers there to better inform future management and …

Performance Enhancement And Characterization Of An Electromagnetic Railgun, Paul M. Gilles

Master's Theses

Collision with orbital debris poses a serious threat to spacecraft and astronauts. Hypervelocity impacts resulting from collisions mean that objects with a mass less than 1g can cause mission-ending damage to spacecraft. A means of shielding spacecraft against collisions is necessary. A means of testing candidate shielding methods for their efficacy in mitigating hypervelocity impacts is therefore also necessary. Cal Poly’s Electromagnetic Railgun was designed with the goal of creating a laboratory system capable of simulating hypervelocity (≥ 3 km/s) impacts. Due to several factors, the system was not previously capable of high-velocity (≥ 1 km/s) tests. A deficient projectile …

Dual Graphene Patch Antenna For Ka Band Satellite Applications, Mohammed Amin Rabah, Mohammed Bekhti

International Journal of Aviation, Aeronautics, and Aerospace

Currently; grapheme offers a new opportunity to use in space technology and this is due to its amazing properties like conductivity, strength, flexibility and transparency which allows us to exploit new generation of ultra-fast nanoscale components; Since future wireless communication techniques are geared towards the use of the high frequency spectrum and many recent research prove this trend. This letter presents a proposal for design of a dual graphene-based antenna to use in new communication techniques in Ka band, where the proposed antenna can work for uplink and dowlink frequencies at same time since it has return loss less then …

Design, Fabrication, And Testing Of An Emr Based Orbital Debris Impact Testing Platform, Jeffrey J. Maniglia Jr.

Master's Theses

This paper describes the changes made from Cal Poly’s initial railgun system, the Mk. 1 railgun, to the Mk. 1.1 system, as well as the design, fabrication, and testing of a newer and larger Mk. 2 railgun system. The Mk. 1.1 system is developed as a more efficient alteration of the original Mk. 1 system, but is found to be defective due to hardware deficiencies and failure, as well as unforeseen efficiency losses. A Mk. 2 system is developed and built around donated hardware from the Naval Postgraduate School. The Mk. 2 system strove to implement an efficient, augmented, electromagnetic …

Configuration Studies Of Electrostatic And Magnetostatic Active Space Radiation Shielding, Trac K. Nguyen

Electrical & Computer Engineering Theses & Dissertations

Developing successful and optimal solutions for mitigating the hazards of radiation in deep space is critical for the success of deep-space long duration explorations, including mission to the Moon, Mars and beyond. A recent report (Tripathi et al., 2008) had explored the feasibility of using electrostatic shielding in conjunction with state-of-the-art materials shielding technologies.

In this thesis research, we study the active electrostatic shielding strategy and examine a hybrid configuration that utilizes both electrostatic and magnetostatic fields. The main advantages of this system are shown to be: (i) much lower magnetic fields that could be below the thresholds set for …

Day/Night Band Imager For A Cubesat, Eric Stanton

Electrical Engineering

Day/Night Band (DNB) earth sensing and meteorological systems like the Defense Meteorological Satellite Program (DMSP) Operational Linescan System (OLS) provide visible wavelength imagery 24 hours a day that is used primarily for cloud imaging in support of weather forecasting. This paper describes a compact push-broom imager that meets low light imaging requirements for DMSP OLS and the NOAA/NASA Joint Polar Satellite System (JPSS) as documented in the Integrated Operational Requirements Document [1] (IORD) including the imager design, system level concepts of operation for data collection, radiometric and spatial calibration, and data transmission to Earth. This small, lightweight imager complies with …

Aether, Thomas Cameron, Kristine Colton, Daren Childers

Electrical Engineering

Aether is a RC-style autonomous air vehicle that utilizes GPS positioning along with a wireless communication system to achieve a computer-controlled flight.

This report will incorporate the acquisition, design, integration, implementation and testing phases of the UAV development. Furthermore a discussion of troubleshooting as well as improvements for future projects will be included.