Structures and Materials Commons^™

Towards An Understanding Of The Thermodynamic Properties Of Crtao4: A Computational Perspective, Tanner B. Gordon

Theses and Dissertations

Materials that can withstand higher temperatures are paramount for next-generation aircraft design. Hypersonic capabilities and jet-turbine engines operate in extreme environments. Choosing materials that have high thermal stability and oxidation resistance for these applications can increase engine efficiency, reduce size, weight and power (SWaP), and increase the maneuverability of the aircraft. The mixed oxide CrTaO₄ has been experimentally observed to significantly contribute to oxidation resistance at high temperatures. However, and despite its significance, its properties remain largely unknown. This work explores the thermal properties of this material from a multi-scale approach, by obtaining an accurate description of the thermodynamics …

Experimental And Computational Bearing Strength Of Fiber Metal Laminate With And Without Film Adhesive, Christopher L. Bellanova Jr.

Theses and Dissertations

This research characterized the performance of a fiber metal laminate composed of carbon fiber and stainless steel without film adhesive and compared it to a similar, previously tested, fiber metal laminate including film adhesive. Removal of the adhesive layers reduced the localized thickness, simplified manufacturing, and allowed for a 20% increase in foil thickness. Quasi-static testing was conducted in double shear, single shear protruding, and single shear countersunk configurations. The results were compared to adhesive hybrid and control samples. To study the affects of bolt tension, samples at low torque in double shear were also tested. Progressive failure samples revealed …

Mechanical Properties And Performance Of A Novel Nano-Engineered Unitized Composite With Quasi-Isotropic Layup, Brian Matthew Pudlo

Theses and Dissertations

Carbon nanotubes (CNTs) exhibit outstanding mechanical, electrical, and thermal properties, but are a challenge to effectively implement into macroscopic composites for aerospace applications. This research investigates the mechanical properties and performance of a newly developed hybrid NanoStitch composite, alongside a control polymer matrix composite, at room temperature. Both composite material systems investigated in this work have quasi-isotropic layup. Monotonic tension-tofailure, tension-tension fatigue, and creep tests were performed to characterize the performance of the composites under cyclic and sustained loading. Experimental results obtained for the quasi-isotropic NanoStitch composite were compared to those obtained for the quasi-isotropic control composite. The properties and …

Jcati Carbon Fiber Recycler: Crusher System, Devin Riley

All Undergraduate Projects

With a substantial rise in Carbon Fiber use across all industries, the need for a way to recycle the waste has grown as well. A group of Mechanical Engineering Technology students at Central Washington University funded by the Joint Center for Aerospace Technology (JCATI) have created a machine to recycle waste wing trimmings from the Boeing company’s airplanes. This machine consists of 5 different sub-assemblies being the oven, crusher, gear train, conveyor, and shredder. The purpose of this project was to decrease the deflection in the crusher caused by bulging in the housing and movement of the bearings. To decrease …

Determination Of Damage Initiation Mechanisms In Aerospace Alloys Due To Stress Corrosion Cracking Via In-Situ Microscale Characterization Techniques, Remelisa Esteves

Electronic Theses and Dissertations, 2020-2023

Aluminum alloys are used on aerospace vehicles due to their high strength-to-weight ratio, formability and machinability. However, they become vulnerable to stress corrosion cracking (SCC) during their service life. SCC is primarily caused by the material's stress condition, a suitable corrosive environment and material susceptibility. It is also influenced by a mixture of electrochemical, mechanical, and chemical factors. Due to the complexity of SCC, tools with better resolution and sensitivity are needed to better understand the impact and interaction of the contributing factors. A vast amount of research has been done to study SCC behavior, but the scale of characterization …

Characterizing Air Plasma Sprayed Aluminum Oxide Coatings For The Protection Of Structures In Lunar Environments, Perla Latorre Suarez

Electronic Theses and Dissertations, 2020-2023

Wear-resistant ceramic and ceramic composite coatings are significant to provide durability and support long-duration missions to the moon's surface for rovers, landers, robotic systems, habitats, and many other components. On the Lunar surface, structural components are continuously exposed to lunar dust projectiles that can cause protective coating delamination around the affected area, of protective coatings and this may not be physically visible. Ceramic coatings, composed of alumina, present excellent resistance to different types of wear due to their high strength and hardness as well as the ability to protect structural components from regolith impacts, wear, and abrasive damage. Air Plasma …

Exploring Additive Manufacturing In A Space Environment - A Capstone Design Project Experience, Zain Zafar Khan, Zachary Alan Sobelman, Sharanabasaweshwara Asundi

Mechanical & Aerospace Engineering Faculty Publications

The employment of additive manufacturing in the non-standard environments like space, ships, or submarines has the potential to be an advanced utility not only in the pre-flight production of aerospace components and structures, but also for the onboard manufacturing of components and tools necessary for future space missions. For example, the ability to produce tools and structural components on the International Space Station can provide the space community the opportunity to make repairs and upgrades to the space station without wasting time and resources transporting such materials through additional missions. Additive manufacturing would allow for space missions to use on …

Post-Consolidation Process For Modifying Microscale And Mesoscale Parameters Of 3d Printed Composite Materials, Arief Yudhanto, Alwaleed Aldhirgham, Eric Feron, Gilles Lubineau

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Advancements in additive manufacturing technology (3D printing) have enabled us to fabricate reasonably good parts using continuous fiber-reinforced matrix composites. Unfortunately, most of these 3D-printed composite parts inherently possess a large number of voids originating from the trapped air within and between molten composite beads during the deposition stage. Removing the voids has thus become a key challenge in attempts to apply 3D printed composite parts for fabricating stiff/strong load-bearing structures. Here, we employed a classical process, viz. compression molding, to post-consolidate 3D-printed continuous carbon fiber-reinforced polyamide (CFPA), and to investigate the implications in terms of microscale parameters (void content) …

Impact Of Spallation And Internal Radiation On Fibrous Ablative Materials, Raghava Sai Chaitanya Davuluri

Theses and Dissertations--Mechanical and Aerospace Engineering

Space vehicles are equipped with Thermal Protection Systems (TPS) that encounter high heat rates and protect the payload while entering a planetary atmosphere. For most missions that interest NASA, ablative materials are used as TPS. These materials undergo several mass and energy transfer mechanisms to absorb intense heat. The size and construction of the TPS are based on the composition of the planetary atmosphere and the impact of various ablative mechanisms on the flow field and the material. Therefore, it is essential to quantify the rates of different ablative phenomena to model TPS accurately. In this work, the impact of …

Study Of Nanocomposite Materials Using Molecular Dynamics, Prashik Sunil Gaikwad

Dissertations, Master's Theses and Master's Reports

There is an increase in demand for new lightweight structural materials in the aerospace industry for more efficient and affordable human space travel. Polymer matrix composites (PMCs) with reinforcement material as carbon nanotubes (CNTs) have shown exceptional increase in the mechanical properties. Flattened carbon nanotubes (flCNTs) are a primary component of many carbon nanotube (CNT) yarn and sheet materials, which are promising reinforcements for the next generation of ultra-strong composites for aerospace applications. These flCNT/polymer materials are subjected to extreme pressure and temperature during curing process. Therefore there is a need to investigate the evolution of properties during the curing …

Molecular Dynamics Modeling Of Polymers For Aerospace Composites, Swapnil Sambhaji Bamane

Dissertations, Master's Theses and Master's Reports

Polymer matrix composite materials are widely used as structural materials in aerospace and aeronautical vehicles. Resin/reinforcement wetting and the effect of polymerization on the thermo-mechanical properties of the resin are key parameters in the manufacturing of aerospace composite materials. Determining the contact angle between combinations of liquid resin and reinforcement surfaces is a common method for quantifying wettability. It is challenging to determine contact angle values experimentally of high-performance resins on CNT materials such as CNT, graphene, bundles or yarns, and BNNT surfaces. It is also experimentally difficult to determine the effect of polymerization reaction on material properties of a …

Noise Reduction Techniques In Commercial Aircraft Cabins, Hashem Hashem

Student Works

Main sources of noise heard inside an aircraft cabin:

• Engines
• Airframe & control surfaces
• Window vibrations
• Passenger announcements & activities.

Surface Preparation Study, Ryan Ferguson

Williams Honors College, Honors Research Projects

This work explores a custom air atmospheric pressure plasma treatment (APPT) machine’s effectiveness in cleaning and chemically activating a CFRP surface. It is explore by implementing water contact angle (WCA) measurements, water-break free (WBF) testing, and adhesive tubular lap-joint (TLJ) tensile testing. An 8x3 test matrix of different machine parameters is defined with the bounding conditions being the machine’s capabilities and industry standard recommendations. Each configuration of the test matrix is explored after treatment at multiple time intervals up to 2 weeks afterwards to gain insight into the outlife of the treatments with the intention of adhesively bonding to the …

Application Of Multi-Scale Computational Techniques To Complex Materials Systems, Mujan N. Seif

Theses and Dissertations--Chemical and Materials Engineering

The applications of computational materials science are ever-increasing, connecting fields far beyond traditional subfields in materials science. This dissertation demonstrates the broad scope of multi-scale computational techniques by investigating multiple unrelated complex material systems, namely scandate thermionic cathodes and the metallic foam component of micrometeoroid and orbital debris (MMOD) shielding. Sc-containing "scandate" cathodes have been widely reported to exhibit superior properties compared to previous thermionic cathodes; however, knowledge of their precise operating mechanism remains elusive. Here, quantum mechanical calculations were utilized to map the phase space of stable, highly-faceted and chemically-complex W nanoparticles, accounting for both finite temperature and chemical …

Computational And Experimental Investigation Of Mass Reduced Aircraft Wing Ribs, Charles R. Fricks Iii

College of Graduate Studies: Theses & Dissertations

This study seeks to develop and evaluate a novel design of mass reduced aircraft wing ribs through the topology optimization method. For comparison, the same examination is performed on ribs with normal internal geometry. The wing rib design is based on that of the Gulfstream G650 transonic jet. The rib was divided into three segments for analysis based around the positions of the two spars. Only the center section of the rib (that being between the forward and aft spars) is mass optimized, while the leading and trailing edges of the ribs (outside the spars) will be kept solid for …