Structures and Materials Commons^™

Accelerated Controller Tuning For Wind Turbines Under Multiple Hazards, Aly Mousaad Aly, Milad Rezaee

Faculty Publications

During their lifecycle, wind turbines can be subjected to multiple hazard loads, such as high-intensity wind, earthquake, wave, and mechanical unbalance. Excessive vibrations, due to these loads, can have detrimental effects on energy production, structural lifecycle, and the initial cost of wind turbines. Vibration control by various means, such as passive, active, and semi-active control systems provide crucial solutions to these issues. We developed a novel control theory that enables semi-active controller tuning under the complex structural behavior and inherent system nonlinearity. The proposed theory enables the evaluation of semi-active controllers’ performance of multi-degrees-of-freedom systems, without the need for time-consuming …

Design And Analysis Of Air-Stiffened Vacuum Lighter-Than-Air Structures, Ruben Adorno-Rodriguez

Theses and Dissertations

Lighter-than-air (LTA) systems have been developed for numerous applications and have taken several forms. Airships, aerostats, blimps, and balloons are all part of this family of systems, which uses Archimedes principle to achieve neutral and positive buoyancy in air by replacing an air volume with LTA gases. These lifting gases stiffen the otherwise compliant envelope structures, allowing them to sustain the pressure difference brought by the displaced air. The compliance of these structures is a byproduct of the weight requirement, materials and geometrical arrangement of which these structures are built from, typically resulting in dimensionalities that exhibit low or virtually …

Static Fatigue Of Hi-Nicalon™ S Ceramic Fiber Tows At 600°C In Air And Silicic Acid-Saturated Steam, Caleigh M. Nelson

Theses and Dissertations

Ceramic matrix composites (CMCs) have the potential to be utilized in applications such as hypersonic vehicles, aircraft leading edges, hot sections of engines, and rocket nozzles. Of particular interest are advanced SiC/SiC composites that can withstand the elevated temperatures and harsh oxidizing environments while maintaining their properties and structural integrity under an applied load. Steam, a major component of combustion environment, is one such aggressive oxidizing environment. As steam passes through the SiC/SiC composite, entering the composite interior through the cracks in the SiC matrix, it becomes saturated with silicic acid, Si(OH)₄. Before incorporating SiC/SiC composites in the …

Fatigue Of Two Oxide/Oxide Ceramic Matrix Composites At 1200°C In Air And In Steam. Effect Of Diamond Drilled Effusion Holes, Anthony R. Cabri

Theses and Dissertations

The tension-tension fatigue behavior of two oxide-oxide ceramic matrix composites (CMCs) was investigated at 1200°C in laboratory air and steam. Both composites consist of a porous oxide matrix reinforced with laminated, woven mullite/alumina (NextelTM720) fibers. The first composite had an alumina matrix, while the second had an alumina-mullite matrix. First, we assessed the effects of incorporating mullite into the matrix material on fatigue performance by studying the tension-tension fatigue behavior of alumina-mullite matrix CMC. Second, we evaluated the effects of effusion holes on the alumina matrix CMC's fatigue performance. Specimens containing an array of 17 effusion holes of 0.5-mm diameter …

On The Influence Of Heat Treatment On Microstructure And Mechanical Behavior Of Laser Powder Bed Fused Inconel 718, Jakob Shroder, Tatiana Mishurova, Tobias Fritsch, Itziar Serrano-Munoz, Alexander Evans, Maximilian Sprengel, Maximilian Sprengel, Manuela Klaus, Giovanni Bruno

PRC-Affiliated Research

A range of heat treatments have been developed for wrought Inconel 718 to obtain desired properties. For additively manufactured Inconel 718, the recently developed standard ASTM F3301 provides guidance for heat treatment of powder bed fusion specimens. Although this standard is based on standards developed for wrought Inconel 718, it does not include direct aging. Since direct aging reduces the number of processing steps, it can result in a post processing cost reduction if the desired properties are obtained. In this study, we characterized the microstructure and tensile behavior of Inconel 718 specimens produced by a laser powder bed fusion …

On The Influence Of Heat Treatment On Microstructure And Mechanical Behavior Of Laser Powder Bed Fused Inconel 718, Jakob Shroder, Tatiana Mishurova, Tobias Fritsch, Itziar Serrano-Munoz, Alexander Evans, Maximilian Sprengel, Maximilian Sprengel, Manuela Klaus, Giovanni Bruno

PRC-Affiliated Research

A range of heat treatments have been developed for wrought Inconel 718 to obtain desired properties. For additively manufactured Inconel 718, the recently developed standard ASTM F3301 provides guidance for heat treatment of powder bed fusion specimens. Although this standard is based on standards developed for wrought Inconel 718, it does not include direct aging. Since direct aging reduces the number of processing steps, it can result in a post processing cost reduction if the desired properties are obtained. In this study, we characterized the microstructure and tensile behavior of Inconel 718 specimens produced by a laser powder bed fusion …

Tooling Design Modeling For Composite Fuselage Of Beechcraft King Air 250 Using Catia, Miazor Fidelis Ekom

Journal of Aviation Technology and Engineering

Aircraft’s constant operation in tough conditions necessitates the need for structural components of high strength yet low weight. Composite materials are being used as an alternative to conventional aluminum alloys because of their competitive strength-to-weight and stiffness-to-weight ratios. In this paper, the detailed design procedure of a light-aircraft composite material fuselage tooling in three dimensions is shown. In its operation, the layup tools provide a surface for the composite part which is the correct shape of the part and is stable through the cure cycle, and also providing a means of indexing the part for the next manufacturing operation. This …

Numerical Reconstruction Of Spalled Particle Trajectories In An Arc-Jet Environment, Raghava S. C. Davuluri, Sean C. C. Bailey, Kaveh A. Tagavi, Alexandre Martin

Mechanical Engineering Faculty Publications

To evaluate the effects of spallation on ablative material, it is necessary to evaluate the mass loss. To do so, a Lagrangian particle trajectory code is used to reconstruct trajectories that match the experimental data for all kinematic parameters. The results from spallation experiments conducted at the NASA HYMETS facility over a wedge sample were used. A data-driven adaptive methodology was used to adapts the ejection parameters until the numerical trajectory matches the experimental data. The preliminary reconstruction results show that the size of the particles seemed to be correlated with the location of the ejection event. The size of …

Simulation Of A Trailing Edge Flap Using A Compliant Mechanism, Sam Blackwell

Summer Community of Scholars Posters (RCEU and HCR Combined Programs)

No abstract provided.

The Kentucky Re-Entry Universal Payload System (Krups): Orbital Flight, James Tyler Nichols

Theses and Dissertations--Mechanical and Aerospace Engineering

Due to the uniqueness of atmospheric entry environments, ground facilities cannot accurately replicate re-entry conditions. Consequently, scientists primarily rely on numerical models to predict these conditions and inform Thermal Protection System (TPS) designs. These models often lack flight validation, which is necessary for increasing their fidelity. Thus, there is a substantial need to obtain such data to advance modeling capabilities.

The Kentucky Re-entry Universal Payload System (KRUPS) is an adaptable test-bed for scientific experimentation with initial application to TPS. This vehicle was designed at the University of Kentucky to serve as an inexpensive means of obtaining validation data to enhance …

A Computational Fluid-Structure Interaction Method For Simulating Supersonic Parachute Inflation, Jonathan Boustani

Theses and Dissertations--Mechanical and Aerospace Engineering

Following the successful landing of the Curiosity rover on the Martian surface in 2012, NASA/JPL conducted the low-density supersonic decelerator (LDSD) missions to develop large diameter parachutes to land the increasingly heavier payloads being sent to the Martian surface. Unexpectedly, both of the tested parachutes failed far below their design loads. It became clear that there was an inability to model and predict loads that occur during supersonic parachute inflation. In this dissertation, a new computational method that was developed to provide NASA with the capability to simulate supersonic parachute inflation is presented and validated. The method considers the loose …

Structural Optimization Of Space Transit Vehicle Concept, Hercules, James Philip Rogers

Theses and Dissertations--Mechanical and Aerospace Engineering

STRUCTURAL OPTIMIZATION OF SPACE TRANSIT VEHICLE CONCEPT, HERCULES:

A COMPARATIVE STUDY OF STRUCTURAL OPTIONS

Hercules is a vehicle concept developed by NASA Langley's Vehicle Analysis Branch to satisfy the need for sustainable transit between Earth, the moon, and Mars. Hercules features unprecedented abort capabilities and mission flexibility to aid in NASA's Mars campaign. By utilizing modern software to perform structural analysis and optimization for a large selection of stiffened panel concepts, beam concepts, and materials trends in the structural optimization emerge. These trends will be invaluable for the design of future spacecraft needed to fulfill similar roles.

The structural optimization …

Role Of Eta Phase Evolution On Creep Properties Of Nickel Base Superalloys Used In Advanced Electric Power Generation Plants, Ninad Mohale

Dissertations, Master's Theses and Master's Reports

Advanced fossil energy power generation plants require materials that withstand high temperatures and corrosive environments. One such material that is used in steam turbines is Nimonic 263. It is a nickel-base superalloy that is principally strengthened by gamma primephase (Ni₃(Ti, Al)) and has an L1₂structure. At extended times and at turbine operating temperatures however, eta (Ni₃Ti) phase is known to form at the expense of gamma prime. Eta has a complex DO₂₄structure and is the stable phase between 750°C and 900°C, but with slow kinetics of formation. Little is understood about eta …

Mechanical Properties Of Nanomodified Hybrid Gfrp Composite Materials, Micah Rop Kimutai

College of Graduate Studies: Theses & Dissertations

The mechanical behavior of the nanomodified hybrid epoxy matrix was investigated in glass fiber reinforced plastics (GFRP). In this study, five nanocomposites enriched with as received halloysite, nanomer I.28E, HNT-APTES, and the hybrid combinations of the two HNTs with the nanomer I.28E were successfully fabricated. To evaluate the effects and morphological characteristics of the individual fillers and the hybrid configurations on the epoxy resin matrix, TGA, DSC, and DMA were analyzed. To understand the effect of the five configurations on the neat GFRP laminate, mode I interlaminar fracture toughness, tensile, and vibration properties were investigated. Electron microscopy testing techniques were …