Structures and Materials Commons^™

High Dynamic Range Optical Devices And Applications., Elijah Robert Jensen

Electronic Theses and Dissertations

Much of what we know about fundamental physical law and the universe derives from observations and measurements using optical methods. The passive use of the electromagnetic spectrum can be the best way of studying physical phenomenon in general with minimal disturbance of the system in the process. While for many applications ambient visible light is sufficient, light outside of the visible range may convey more information. The signals of interest are also often a small fraction of the background, and their changes occur on time scales so quickly that they are visually imperceptible. This thesis reports techniques and technologies developed …

Numerical Simulation Of A High Strain Rate Biaxial Compression Apparatus, Michael Lagieski

McKelvey School of Engineering Graduate Student Theses & Dissertations

Few experimental methods today are capable of exploring the strength of materials at high strain rates (10⁵ s^-1). Those that are capable, such as the Split Hopkinson Bar, Taylor Anvil and Plate Impact suffer from instability and are generally limited to one dimensional wave propagation. Of particular interest is material response under biaxial compression, similar to that seen in inertial confinement fusion. Laser fusion fuel pellets typically undergo large strain rates as well as plastic deformation and non-linear behavior. This work briefly outlines an experimental procedure designed to replicate these large strain rates under biaxial compression using …

An Enhanced Operational Definition Of Dielectric Breakdown For Dc Voltage Step-Up Tests, Allen Andersen, Jr Dennison

Journal Articles

The imprecise definition of breakdown in the ASTM D3755-14 standard can misidentify breakdown. If the recommended test circuit current sensing element threshold is set too high, breakdown may occur undetected. Conversely, false positives may result from designating a low current threshold. An operational definition of breakdown much less sensitive to these pitfalls is outlined herein. This enhanced definition of breakdown is based on the average rate of change of the leakage current with increasing voltage, rather than a simple current threshold, avoiding ambiguous association with anomalies in current traces. For tests that continuously monitor leakage current, breakdown can be detected …

Hazard Assessment Of Meteoroid Impact For The Design Of Lunar Habitats, Herta Paola Montoya, Shirley Dyke, Julio A. Ramirez, Antonio Bobet, H. Jay Melosh, Daniel Gomez

The Summer Undergraduate Research Fellowship (SURF) Symposium

The design of self-sustaining lunar habitats is a challenge primarily due to the Moon’s lack of atmospheric protection and hazardous environment. To assure safe habitats that will lead to further lunar and space exploration, it is necessary to assess the different hazards faced on the Moon such as meteoroid impacts, extreme temperatures, and radiation. In particular, meteoroids pose a risk to lunar structures due to their high frequency of occurrence and hypervelocity impact. Continuous meteoroid impacts can harm structural elements and vital equipment compromising the well-being of lunar inhabitants. This study is focused on the hazard conceptualization and quantification of …

Multi-Dome Forming Of A Ti–Al–Mn Alloy, Sergey Aksenov, Aleksey Kolesnikov, Ivan Zakhariev

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.

Large Linear Magnetoresistance In Heavily-Doped Nb:Srtio3 Epitaxial Thin Films, Hyunwoo Jin, Keundong Lee, Seung-Hyub Baek, Jin-Sang Kim, Byung-Ki Cheong, Bae Ho Park, Sungwon Yoon, B. J. Suh, Changyoung Kim, Sung S. Ambrose Seo, Suyoun Lee

Physics and Astronomy Faculty Publications

Interaction between electrons has long been a focused topic in condensed-matter physics since it has led to the discoveries of astonishing phenomena, for example, high-T_c superconductivity and colossal magnetoresistance (CMR) in strongly-correlated materials. In the study of strongly-correlated perovskite oxides, Nb-doped SrTiO₃ (Nb:SrTiO₃) has been a workhorse not only as a conducting substrate, but also as a host possessing high carrier mobility. In this work, we report the observations of large linear magnetoresistance (LMR) and the metal-to-insulator transition (MIT) induced by magnetic field in heavily-doped Nb:STO (SrNb_0.2Ti_0.8O₃) epitaxial thin …

Growth Control Of Oxygen Stoichiometry In Homoepitaxial Srtio3 Films By Pulsed Laser Epitaxy In High Vacuum, Ho Nyung Lee, Sung S. Ambrose Seo, Woo Seok Choi, Christopher M. Rouleau

Physics and Astronomy Faculty Publications

In many transition metal oxides, oxygen stoichiometry is one of the most critical parameters that plays a key role in determining the structural, physical, optical, and electrochemical properties of the material. However, controlling the growth to obtain high quality single crystal films having the right oxygen stoichiometry, especially in a high vacuum environment, has been viewed as a challenge. In this work, we show that, through proper control of the plume kinetic energy, stoichiometric crystalline films can be synthesized without generating oxygen defects even in high vacuum. We use a model homoepitaxial system of SrTiO₃ (STO) thin films on …

The Robert & Esther Goddard Papers, Robert H. Goddard

Finding Aids

Dr. Robert H. Goddard was a member of the Clark Physics Department for 29 years. Foremost American pioneer of rocket research, he laid the technical and theoretical foundations for many of the developments in long-range rockets, missiles, satellites and space flight, which collectively put us into the Space Age.

The collection includes correspondence, diaries, journals, patent applications and awards, reports, and photographs. The collection also includes original paintings by Dr. Goddard.

Techniques For Payload Stabilization For Improved Photography During Stratospheric Balloon Flights, James Flaten, Christopher Gosch, Joseph (Benjamin) Habeck

2017 Academic High Altitude Conference

Payload-box rotation and swing are perennial challenges to achieving high-quality photography (typically videography) during weather-balloon flights to “near-space” (AKA the stratosphere). Continuous camera motion can lead to blurred still photos, nearly-impossible-to-watch video footage, and precludes time-exposure photography required for most astronomical imaging even though altitudes are reached where the daytime sky appears black. Apparently-random payload rotation, persisting even at altitude, can often exceed servo rotation rates and frustrate attempts to do active camera pointing. Here we discuss mostly-passive payload stabilization strategies we, and our collaborators, have used to mitigate and dampen both swing and rotation of suspended payloads on high-altitude …

Molecular Dynamics Model Of Carbon Nanotubes In Epon 862/Detda Polymer, Guttormur Arnar Ingvason

Doctoral Dissertations and Master's Theses

The aerospace industry is interested in increasing the strength while reducing the weight of carbon fiber composite materials. Adding single walled carbon nanotubes (SWCNT) to a polymer matrix can achieve that goal by improving delamination properties of the composite. Due to the complexity of polymer molecules and the curing process, few 3-D Molecular Dynamics simulations of a polymer-SWCNT composite have been run. Our model runs on the Large-scale Atomic/Molecular Massively Parallel Simulator (LAMMPS), with a COMPASS (Condensed phase Optimized Molecular Potential for Atomistic Simulations Studies) potential to represent the interactions between the atoms of the polymer and the SWCNT. This …

Traditional Boat Building: An Intersection Of Zanzibar’S Culture And Environment, Eric Levenson

Independent Study Project (ISP) Collection

This study examined traditional boat building on Uzi Island as a manifestation of Zanzibar’s relationship of environment and culture. Information was gathered about traditional boat building practices, the resource use and management pertaining to boats, the cultural reliance on boats, and local views on environment and conservation. This information showed that the people of Uzi Island were dependent on the use of traditional boats to maintain their livelihood, however the tree types used for boat building are being over-harvested. This tension of culture and environment exposed the need for conservation of Zanzibar’s natural resources in a manner that does not …

Guided Wave-Based J-Integral Estimation For Dynamic Stress Intensity Factors Using 3d Scanning Laser Doppler Vibrometry, J. Ayers, Christopher Todd Owen, Eric D. Swenson, Anindya Ghoshal, V. Weiss

Faculty Publications

The application of guided waves to interrogate remote areas of structural components has been researched extensively in characterizing damage. However, there exists a sparsity of work in using piezoelectric transducer-generated guided waves as a method of assessing stress intensity factors (SIF). This quantitative information enables accurate estimation of the remaining life of metallic structures exhibiting cracks, such as military and commercial transport vehicles. The proposed full wavefield approach, based on 3D laser vibrometry and piezoelectric transducer-generated guided waves, provides a practical means for estimation of dynamic stress intensity factors (DSIF) through local strain energy mapping via the J-integral. Strain energies …

Response Surface Optimization Of Electron Beam Freeform Fabrication Depositions Using Design Of Experiments, Patricia A. Quigley

Engineering Management & Systems Engineering Theses & Dissertations

The Electron Beam Freeform Fabrication (EBF³ ) System is a material depositing, layer additive technique that produces three dimensional (3D) parts out of a wide range of metals in high vacuum, using an electron beam and wire feedstock. Screening deposition trials on a titanium alloy, Ti-6Al-4V, at the National Aeronautics Space Administration (NASA) revealed selective vaporization of the aluminum content of linear prototypes when subjected to chemical analysis. In this study, the aluminum content, bead height and bead width output responses were analyzed from a systematic study of the effects that the interactions of the EBF³ processing parameters …

Development Of A Pyrotechnic Shock Simulation Apparatus For Spacecraft Applications, Joseph Binder, Matthew Mccarty, Chris Rasmussen

Aerospace Engineering

This report details the research, design, construction, and testing of a pyrotechnic shock simulation apparatus for spacecraft applications. The apparatus was developed to be used in the Space Environments Lab at California Polytechnic State University. It will be used for testing spacecraft components with dimensions up to 24”x12”x12” as well as CubeSats. Additionally, it may be used as an instructional or demonstrational tool in the Aerospace Department’s space environments course. The apparatus functions by way of mechanical impact of an approximately 20 lb stainless steel swinging hammer. Tests were performed to verify the simulator’s functionality. Suggestions for improvement and further …

Design Of Orbital Maneuvers With Aeroassisted Cubesatellites, Stephanie Clark

Graduate Theses and Dissertations

Recent advances within the field of cube satellite technology has allowed for the possible development of a maneuver that utilizes a satellite's Low Earth Orbit (LEO) and increased atmospheric density to effectively use lift and drag to implement a noncoplanar orbital maneuver. Noncoplanar maneuvers typically require large quantities of propellant due to the large delta-v that is required. However, similar maneuvers using perturbing forces require little or no propellant to create the delta-v required. This research reported here studied on the effects of lift on orbital changes, those of noncoplanar types in particular, for small satellites without orbital maneuvering thrusters. …

Predicting Solar Protons: A Statistical Approach, Jonathan C. Spaulding

Theses and Dissertations

A small fraction of solar flares are accompanied by high energy (>10 MeV) protons. These events can cause degradation or failure of satellite systems and can be harmful to humans in space or in high altitude flight. For risk management purposes, the Air Force is interested in predicting these events. Several algorithms exist to do this operationally, but none predict when these events will occur with much accuracy. Here, we analyzed 3610 M1 and greater flares including 106 with proton events from the GOES sensors from 1 Jan 1986 to 31 Dec 2004 to produce new results, including a …

Modeling Axisymmetric Optical Precision Piezoelectric Membranes, James W. Rogers Jr.

Theses and Dissertations

The US Department of Defense (DOD), as well as the National Aeronautics and Astronautics Administration (NASA) and the Jet Propulsion Laboratory (JPL) are interested in developing and deploying precise, compliant, light-weight, space-based structures. More specifically, the Air Force’s core competencies ‘Aerospace Superiority’ and ‘Information Superiority’ demand ever-increasing depth and breadth of capability. Whether used for energy transmission or optical reconnaissance, current launch restraints limit rigid space-based optical reflector size. To support this requirement, the Air Force Research Laboratory (AFRL) is developing a large space-based optical membrane telescope. Inflatable reflectors can conceptually break this barrier, but controlling such a compliant structure …

Efficient Dynamic Unstructured Methods And Applications For Transonic Flows And Hypersonic Stage Separation, Xiaobing Luo

Mechanical & Aerospace Engineering Theses & Dissertations

Relative-moving boundary problems have a wide variety of applications. They appear in staging during a launch process, store separation from a military aircraft, rotor-stator interaction in turbomachinery, and dynamic aeroelasticity.

The dynamic unstructured technology (DUT) is potentially a strong approach to simulate unsteady flows around relative-moving bodies, by solving time-dependent governing equations. The dual-time stepping scheme is implemented to improve its efficiency while not compromising the accuracy of solutions. The validation of the implicit scheme is performed on a pitching NACA0012 airfoil and a rectangular wing with low reduced frequencies in transonic flows. All the matured accelerating techniques, including the …

Vortex Wake And Exhaust Plume Interaction, Including Ground Effect, Ihab Gaber Adam

Mechanical & Aerospace Engineering Theses & Dissertations

Computational modeling and studies of the near-field wake-vortex turbulent flows, far-field turbulent wake-vortex/exhaust-plume interaction for subsonic and High Speed Civil Transport (HSCT) airplane, and wake-vortex/exhaust-plume interaction with the ground are carried out. The three-dimensional, compressible Reynolds-Averaged Navier-Stokes (RANS) equations are solved using the implicit, upwind, Roe-flux-differencing, finite-volume scheme. The turbulence models of Baldwin and Lomax, one-equation model of Spalart and Allmaras and two-equation shear stress transport model of Menter are implemented with the RANS solver for turbulent-flow modeling.

For the near-field study, computations are carried out on a fine grid for a rectangular wing with a NACA-0012 airfoil section and …

Three-Dimensional Aerodynamic Design Optimization Using Discrete Sensitivity Analysis And Parallel Computing, Amidu Olawale Oloso

Mechanical & Aerospace Engineering Theses & Dissertations

A hybrid automatic differentiation/incremental iterative method was implemented in the general purpose advanced computational fluid dynamics code (CFL3D Version 4.1) to yield a new code (CFL3D.ADII) that is capable of computing consistently discrete first order sensitivity derivatives for complex geometries. With the exception of unsteady problems, the new code retains all the useful features and capabilities of the original CFL3D flow analysis code. The superiority of the new code over a carefully applied method of finite-differences is demonstrated.

A coarse grain, scalable, distributed-memory, parallel version of CFL3D.ADII was developed based on "derivative stripmining". In this data-parallel approach, an identical copy …

Flow Simulations About Steady-Complex And Unsteady Moving Configurations Using Structured-Overlapped And Unstructured Grids, James Charles Newman Iii

Mechanical & Aerospace Engineering Theses & Dissertations

The limiting factor in simulating flows past realistic configurations of interest has been the discretization of the physical domain on which the governing equations of fluid flow may be solved. In an attempt to circumvent this problem, many Computational Fluid Dynamic (CFD) methodologies that are based on different grid generation and domain decomposition techniques have been developed. However, due to the costs involved and expertise required, very few comparative studies between these methods have been performed. In the present work, the two CFD methodologies which show the most promise for treating complex three-dimensional configurations as well as unsteady moving boundary …

Unsteady Flow Simulations About Moving Boundary Configurations Using Dynamic Domain Decomposition Techniques, Guan-Wei Yen

Mechanical & Aerospace Engineering Theses & Dissertations

A computational method is developed to solve the coupled governing equations of an unsteady flowfield and those of rigid-body dynamics in six degrees-of-freedom (6-DOF). This method is capable of simulating the unsteady flowfields around multiple component configurations with at least one of the components in relative motion with respect to the others. Two of the important phenomena that such analyses can help us to understand are the unsteady aerodynamic interference and the boundary-induced component of such a flowfield. By hybridizing two dynamic domain decomposition techniques, the grid generation task is simplified, the computer memory requirement is reduced, and the governing …

Multigrid Acceleration Of Time-Dependent Solutions Of Navier-Stokes Equations, Sarafa Oladele Ibraheem

Mechanical & Aerospace Engineering Theses & Dissertations

Recent progress in Computational Fluid Dynamics is encouraging scientists to look at fine details of flow physics of problems in which natural unsteady phenomena have hitherto been neglected. The acceleration methods that have proven very successful in steady state computations can be explored for time dependent computations. In this work, an efficient multigrid methods is developed to solve the time-dependent Euler and Navier-Stokes equations. The Beam-Warming ADI method is used as the base algorithm for time stepping calculations. Application of the developed algorithm proved very efficient in selected steady and unsteady test problems. For instance, the inherent unsteadiness present in …

The Solution Of A Singular Integral Equation Arising From A Lifting Surface Theory For Rotating Blades, Mark H. Dunn

Mathematics & Statistics Theses & Dissertations

A technique is presented for the solution of a linear, two dimensional, singular, Volterra integral equation of the first kind. The integral equation, originally developed by Farassat and Myers, is derived from the basic equations of linearized acoustics and models the lifting force experienced by an infinitesimally thin surface moving tangent to itself. As a particular application, the motion of modern high speed aircraft propellers (Advanced Technology Propellers) is considered. The unknown propeller blade surface pressure distribution is approximated by a piecewise constant function and the integral equation is solved numerically by the method of collocation. Certain simplifying assumptions applied …

An Extension Of Essentially Non-Oscillatory Shock-Capturing Schemes To Multi-Dimensional Systems Of Conservation Laws, Jay Casper

Mathematics & Statistics Theses & Dissertations

In recent years, a class of numerical schemes for solving hyperbolic partial differential equations has been developed which generalizes the first-order method of Godunov to arbitrary order of accuracy. High-order accuracy is obtained, wherever the solution is smooth, by an essentially non-oscillatory (ENO) piecewise polynomial reconstruction procedure, which yields high-order pointwise information from the cell averages of the solution at a given point in time. When applied to piecewise smooth initial data, this reconstruction enables a flux computation that provides a time update of the solution which is of high-order accuracy, wherever the function is smooth, and avoids a Gibbs …