Structures and Materials Commons^™

Design Of Selectively Compliant Morphing Wind Turbine Blade Section Using Bistable Laminate For Passive Load Alleviation, Abhishek Chopra, Dr. Andres Arrieta, Janav Udani, Jose Rivas Padilla

The Summer Undergraduate Research Fellowship (SURF) Symposium

The design of passively controlled compliant morphing structures for large scale wind turbine blades has been of interest due to the inherent advantages of lower mass and reduced complexity over their active counterparts. Previous studies have indicated that embedding a locally bi-stable element within the turbine blade section successfully allows for achieving passive load alleviation. The embedded bi-stable member switches from one stable state to another at a critical aerodynamic load. This local structural change results in a global shift in the aeroelastic response of the blade section. Building on these preliminary results, this research investigates a two- dimensional wind …

High Dynamic Range Optical Devices And Applications., Elijah Robert Jensen

Electronic Theses and Dissertations

Much of what we know about fundamental physical law and the universe derives from observations and measurements using optical methods. The passive use of the electromagnetic spectrum can be the best way of studying physical phenomenon in general with minimal disturbance of the system in the process. While for many applications ambient visible light is sufficient, light outside of the visible range may convey more information. The signals of interest are also often a small fraction of the background, and their changes occur on time scales so quickly that they are visually imperceptible. This thesis reports techniques and technologies developed …

Design Survey Of Laminated Composite I-Beam, Mrinmoy Saha

All Graduate Plan B and other Reports, Spring 1920 to Spring 2023

Composite I-beams are popular for high-strength low-weight applications. Learning the macro-mechanics and designing the composite I-beam properly are necessary. In this report, a design overview of the composite I-beam is discussed which is based on classical lamination theory where it includes the homogenization approach, the plane stress assumption and the Kirchhoff hypothesis. Using these assumptions, a method was developed to come up with the effective material properties of a beam. Formulas to calculate maximum deflection and maximum bending stress and shear stress and the stress concentration at the connection of web-flange are discussed which describe ways for designing and manufacturing …

Fracture Initiation In A Transversely Isotropic Solid: Transient Three Dimensional Analysis, Louis Milton Brock

Mechanical Engineering Faculty Publications

A transversely isotropic solid is at rest, and contains a semi-infinite, plane crack. The axis of rotational material symmetry lies in the crack plane. Application of normal point forces to each face of the crack causes transient 3D growth. The related problem of discontinuities in displacement and traction that exist on regions that exhibit dynamic similarity is first considered. Analytic results are obtained in integral transform space. These lead to equations of the Wiener–Hopf type for the fracture problem. Analytic solutions are again obtained and, upon inversion, subjected to a dynamic energy release rate criterion that includes kinetic energy. A …

Active Vibration Control Of Helicopter Rotor Blade By Using A Linear Quadratic Regulator, Md Mosleh Uddin

LSU New Orleans Theses and Dissertations

Active vibration control is a widely implemented method for the helicopter vibration control. Due to the significant progress in microelectronics, this technique outperforms the traditional passive control technique due to weight penalty and lack of adaptability for the changing flight conditions. In this thesis, an optimal controller is designed to attenuate the rotor blade vibration. The mathematical model of the triply coupled vibration of the rotating cantilever beam is used to develop the state-space model of an isolated rotor blade. The required natural frequencies are determined by the modified Galerkin method and only the principal aerodynamic forces acting on the …

Ultrasonic Nondestructive Evaluation Of Metal Additive Manufacturing., Venkata Karthik Nadimpalli

Electronic Theses and Dissertations

Metal Additive Manufacturing (AM) is increasingly being used to make functional components. One of the barriers for AM components to become mainstream is the difficulty to certify them. AM components can have widely different properties based on process parameters. Improving an AM processes requires an understanding of process-structure-property correlations, which can be gathered in-situ and post-process through nondestructive and destructive methods. In this study, two metal AM processes were studied, the first is Ultrasonic Additive Manufacturing (UAM) and the second is Laser Powder Bed Fusion (L-PBF). The typical problems with UAM components are inter-layer and inter-track defects. To improve the …

Numerical Simulation Of A High Strain Rate Biaxial Compression Apparatus, Michael Lagieski

McKelvey School of Engineering Graduate Student Theses & Dissertations

Few experimental methods today are capable of exploring the strength of materials at high strain rates (10⁵ s^-1). Those that are capable, such as the Split Hopkinson Bar, Taylor Anvil and Plate Impact suffer from instability and are generally limited to one dimensional wave propagation. Of particular interest is material response under biaxial compression, similar to that seen in inertial confinement fusion. Laser fusion fuel pellets typically undergo large strain rates as well as plastic deformation and non-linear behavior. This work briefly outlines an experimental procedure designed to replicate these large strain rates under biaxial compression using …

Determination Of Chemical Notch, KChem On Aluminum And Steel When Subjected Under Slow Strain Rate Test In Corrosive Environment, Joshua Teo Lee Kuok

Masters Theses

When designing for any mechanical components or system, the question would arise as to how the material would react to the loads subjected on it? Would the component survive its service load? How would it react to environmental corrosion? To answer these questions, the technique used in this thesis paper is the Slow Strain Rate Test (SSRT) method. Aluminum and steel were chosen as the material to be tested in this paper. Al 7075-T651, and Al 6061-T651 was chosen due to its wide range of application, high strength to weight ratio and ease of machinability. It is highly used in …

Manufacturing Process Simulation – On Its Way To Industrial Application, Dennis Otten, Tobias A. Weber, Jan-Christoph Arent

International Journal of Aviation, Aeronautics, and Aerospace

Manufacturing process simulation (MPS) has become more and more important for aviation and the automobile industry. A highly competitive market requires the use of high performance metals and composite materials in combination with reduced manufacturing cost and time as well as a minimization of the time to market for a new product. However, the use of such materials is expensive and requires sophisticated manufacturing processes. An experience based process and tooling design followed by a lengthy trial-and-error optimization is just not contemporary anymore. Instead, a tooling design process aided by simulation is used more often. This paper provides an overview …

Thermal-Fatigue And Thermo-Mechanical Equivalence For Transverse Cracking Evolution In Laminated Composites, Javier Cabrera Barbero

Graduate Theses, Dissertations, and Problem Reports (ETD)

Carbon fiber reinforced plastics (CFRP) are potential materials for many aerospace and aeronautical applications due to their high specif strength/weight and a low coeffcient of thermal expansion (CTE) resulting in a high long-term stability. Among candidate structures, the re-entry reusable launch vehicles (RLV), the fuel oxidant storage and transportation at cryogenic temperature, space satellites, and aircraft structure (frame, wings, etc...) can be highlighted. However, CFRP are prone to internal damage as a result of high residual stresses and thermal fatigue loading. In this study, micro-cracking damage evolution in laminated composites subjected to monotonic cooling and thermal cyclic loads is developed …

Optimal Sintering Temperature Of Ceria-Doped Scandia Stabilized Zirconia For Use In Solid Oxide Fuel Cells, Amanda K. Assuncao

Honors Undergraduate Theses

Carbon emissions are known to cause decay of the Ozone layer in addition to creating pollutant, poisonous air. This has become a growing concern among scientists and engineers across the globe; if this issue is not addressed, it is likely that the Earth will suffer catastrophic consequences. One of the main culprits of these harmful carbon emissions is fuel combustion. Between vehicles, power plants, airplanes, and ships, the world consumes an extraordinary amount of oil and fuel which all contributes to the emissions problem. Therefore, it is crucial to develop alternative energy sources that minimize the impact on the environment. …

Guardian Condor, Kevin Bayonnet

Williams Honors College, Honors Research Projects

Our group has teamed up with Dr. Williams from Discovery Lab Global to research the capabilities of 3D printed Unmanned Aerial Vehicles (UAVs). The goal of our project is to deliver a 3D printed glider prototype which can later be fitted with electronics for controlled flight. The glider must also carry a payload of 2 to 3 pounds in addition to the electronics. These requirements must be met all while using a basic 3D printer with low cost plastic

Throughout the Fall 2017 semester, our group made a significant amount of progress by completing the conceptual design portion of the …

Design Of Shape-Conforming Nosecone For Optimal Fluid Flow From Transonic To Supersonic Range, Anna Tombazzi

Williams Honors College, Honors Research Projects

Modern flight vehicles, such as rockets, missiles, and airplanes, experience a force caused by forebody wave drag during the flight. This drag force is induced when the frontal point of each vehicle breaks the pressure wave during flight. Efforts to reduce this wave drag force to improve flight efficiency include modifying the nosecone profile of the flight vehicles to lower the drag force.

This project revolved around creating a design to make the transformation of nosecone shapes from a ¾ Parabolic profile to a ½ Power Series profile possible, mid-flight. Using a novel nosecone assembly, shape memory alloys (SMAs) and …

Investigation Of 2195 And 2219 Post Weld Heat Treatments For Additive Friction Stir Lap Welds, Matthew Champagne

LSU New Orleans Theses and Dissertations

To evaluate potential uses for friction stir welding in additive manufacturing, two separate parts were fabricated, one of 2195-T84 and the other 2219-T87, utilizing fixed pin techniques and additive lap welds. The parts were cut into samples, artificially aged and subjected to Rockwell hardness (HRB), Vickers hardness, micrographic photography, and metallographic imaging on both pre- and post- heat treatment. Additionally, tensile testing was performed on the heat-treated samples. A comparisons of test results showed a minimal increase in the yield strength of the 2195-T84 samples compared to as-welded tensile results obtained from a previous project. The ultimate tensile strength was …

Design, Manufacture, And Structural Dynamic Analysis Of A Biomimetic Insect-Sized Wing For Micro Air Vehicles, Jose Enrique Rubio

LSU New Orleans Theses and Dissertations

The exceptional flying characteristics of airborne insects motivates the design of biomimetic wing structures that can exhibit a similar structural dynamic behavior. For this purpose, this investigation describes a method for both manufacturing a biomimetic insect-sized wing using the photolithography technique and analyzing its structural dynamic response. The geometry of a crane fly forewing (family Tipulidae) is acquired using a micro-computed tomography scanner. A computer-aided design model is generated from the measurements of the reconstructed scanned model of the insect wing to design the photomasks of the membrane and the venation network required for the photolithography procedure. A composite …

Transient Analysis Of Fracture Initiation In A Coupled Thermoelastic Solid, Louis Milton Brock

Mechanical Engineering Faculty Publications

An isotropic, thermoelastic solid is initially at rest at uniform (absolute) temperature, and contains a semi-infinite, plane crack. Application of in-plane and normal point forces to each face of the crack causes transient 3D growth. The related problem of discontinuities in temperature and displacement that exist on regions that exhibit dynamic similarity is first considered. Asymptotic expressions, whose inverses are valid near the crack edges for short times, are obtained in integral transform space. These lead to equations of the Wiener–Hopf type for the fracture problem. Analytical solutions are obtained and, upon inversion, subjected to a dynamic energy release rate …

Deployable Antenna For Cubesat, Mackenzie Thomas Lennon, Caleb Andrew Barber, David Matthew Galves

Mechanical Engineering

This project is a proof-of-concept ground model of a large deployable antenna designed for the small space requirements of CubeSats. This small deployment module is designed to fit a 2 m by 1 m reflective antenna inside a storage volume of with the dimensions 20 cm by 20 cm x 40 cm. The reflector will be deployed to a parabolic shape with the goal of modeling the reflector necessary for high frequency communication. Because this module is designed as a proof-of-concept for the deployable parabolic reflector specifically, no electrical components will be incorporated and will just focus on the deployment …

The Effect Of Biocomposite Material In A Composite Structure Under Compression Loading, Benjamin Andrew Sweeney

Master's Theses

While composite structures exhibit exceptional strength and weight saving possibilities for engineering applications, sometimes their overall cost and/or material performance can limit their usage when compared to conventional structural materials. Meanwhile ‘biocomposites’, composite structures consisting of natural fibers (i.e. bamboo fibers), display higher cost efficiency and unique structural benefits such as ‘sustainability’. This analysis will determine if the integration of these two different types of composites are beneficial to the overall structure. Specifically, the structure will consist of a one internal bamboo veneer biocomposite ply; and two external carbon fiber weave composite plies surrounding the bamboo biocomposite. To acquire results …

A Multiscale Model For Damage Progression And Detection In Piezo/Pyroelectric Composite Laminates, Yehia Bahei-El-Din, Amany Micheal

Centre for Advanced Materials

Assessment of damage initiation and progression in composite structures reinforced with electrically active filaments is modelled in a multiscale analysis. The analysis developed is a two-tier, interactive analysis, which involves two length scales; macroscopic, and microscopic. The proposed multiscale analysis provides seamless integration of the mechanics at the two length scales, including piezoelectric and pyroelectric coupling effects and damage under overall thermomechanical loads and an electric field applied to electroactive fibers. The macromechanical analysis is performed for multidirectional, fibrous laminates using the lamination theory, including bending, and the micromechanical analysis is performed using a two-phase model and a periodic array …

Detecting Laminate Damage Using Embedded Electrically Active Plies – An Analytical Approach, Amany Micheal, Yehia Bahei-El-Din

Centre for Advanced Materials

Assessment of damage initiation and progression in composite laminates with embedded electrically active plies is modeled. Utilizing electrically active layers embedded in composite laminates as damage sensors is proposed by several researchers and is mainly assessed experimentally. Sensing damage using embedded electrically active plies is generally preferred over the use of surface mounted PZT wafers since the range of the latter is limited to a very narrow area underneath the surface, while multiple damage mechanisms can generally be found in several plies of the laminate. The solution presented invokes two levels of analysis. Firstly, on the laminate level, applied membrane …

Weather Balloon Payload Box, Shellbie Liberty

All Undergraduate Projects

A payload box holding a self-rotating camera was constructed to go on a weather balloon that will document the upcoming solar eclipse on August 21, 2017. A group of physics students, and the paper’s author, are working under Dr. Darci Snowden on the CWU Near Space Observation Team for research dedicated to the eclipse in Oregon. Various projects, including the payload box, are being designed to go up on a high altitude weather balloon. The payload box was designed and constructed to withstand the impact force of falling from 120,000 ft. This was done so the box could be reusable …

Analytical Strip Method For Thin Cylindrical Shells, John T. Perkins

Theses and Dissertations--Civil Engineering

The Analytical Strip Method (ASM) for the analysis of thin cylindrical shells is presented in this dissertation. The system of three governing differential equations for the cylindrical shell are reduced to a single eighth order partial differential equation (PDE) in terms of a potential function. The PDE is solved as a single series form of the potential function, from which the displacement and force quantities are determined. The solution is applicable to isotropic, generally orthotropic, and laminated shells. Cylinders may have simply supported edges, clamped edges, free edges, or edges supported by isotropic beams. The cylindrical shell can be stiffened …

Finite Element Simulation Of Pzt-Aided Interrogation Of Composite Laminates Exhibiting Damage, Amany Micheal, Yehia Bahei-El-Din

Centre for Advanced Materials

Piezoelectricity has proved effective in capturing changes in structures caused by various damage mechanisms. In one approach, piezoelectric wafer active sensors (PWAS) are mounted on the surface of the host structure and utilized as both actuators and sensors to interrogate the structure and monitor its health. This is achieved by subjecting the PWAS to a transient electric pulse and reading the resulting voltage. Changes in the stiffness of the substrate due to structural damage affect the response of the PWAS, which could be correlated to integrity of the structure. Applying this technique to fibrous composite laminates encounters particular challenges due …

Simulation Investigation Of Temperature Distribution In Large Aluminium Panel During Autoclave Age Forming Process, Yongqian Xu

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.

Multi-Dome Forming Of A Ti–Al–Mn Alloy, Sergey Aksenov, Aleksey Kolesnikov, Ivan Zakhariev

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.

Improving Damage Tolerance Of Composite Sandwich Structures Subjected To Low Velocity Impact Loading: Experimental And Numerical Analysis, Ravi B. Gondaliya

Doctoral Dissertations and Master's Theses

Sandwich structures with composite facing skins have seen applications in variety of sectors including aerospace and automobile, owing to their high specific mechanical properties. However, there is a need to develop better damage tolerant sandwich structures since conventional composite facing skins exhibit low impact resistance in the transverse direction. Here, composite skin sandwich structures with three different impact resistant core materials were fabricated and tested both experimentally and numerically. Neat CFRP and 2024-T3 aluminum alloy sheets were also investigated. Cores utilizing impact resistant D3O® were found to have very favorable weight specific energy absorbing properties at higher impact velocities as …

Cryogenic Processing Of Al 7050-T7451 Alloy For Improved Surface Integrity, Bo Huang

Theses and Dissertations--Mechanical and Aerospace Engineering

Al 7050-T7451 alloy with good combinations of strength, stress corrosion cracking resistance and toughness, is used broadly in the aerospace/aviation industry for fatigue-critical airframe structural components. However, it is also considered as a highly anisotropic alloy as the crack growth behavior along the short transverse direction is very different from the one in the long transverse direction, due to the inhomogeneous microstructure with the elongated grains distributed in the work material used in the sheet/plate applications. Further processes on these materials are needed to improve its mechanical and material properties and broaden its applications.

The material with ultra-fine or nano …

Constructal Alkaline Membrane Fuel Cell (Amfc) Design, E. M. Sommer, J. V. C. Vargas, Lauber De Souza Martins, J. C. Ordonez

Faculty Publications

This paper introduces a structured procedure to optimize the internal structure (relative sizes, spacing) and external shape (aspect ratios) of a single alkaline membrane fuel cell so that net power is maximized. The optimization of flow geometry is conducted for the smallest (elemental) level of a fuel cell stack, i.e., the single alkaline membrane fuel cell, which is modeled as a unidirectional flow system. The polarization curve, total and net power, and efficiency are obtained as functions of temperature, pressure, electrolyte solution concentration (KOH), geometry and operating parameters. The optimization is subjected to fixed total volume. There are two levels …

Suborbital Spaceflight: A Student Team’S Plan To Send A Rocket To Space, Bryce Chanes, William Carpenter, Julio Benavides, Matthew Haslam, Brenda Haven

Aviation / Aeronautics / Aerospace International Research Conference

The Eagle Space Flight Team was created with the goal of becoming the first undergraduate team to design, build, and launch a rocket capable of suborbital spaceflight. In order to achieve this goal, the team will have to design a rocket capable of atmospheric flight at speeds over Mach 5 and launch it on one of the largest amateur rocket motors ever made. Over the next three years, the team will progress towards accomplishing this feat through a series of incremental test flights. Before the space flight, the team will build three sub-scale rockets designed to reach altitudes of 30,000’, …

Shape Memory Behavior Of Single Crystal And Polycrystalline Ni-Rich Nitihf High Temperature Shape Memory Alloys, Sayed M. Saghaian

Theses and Dissertations--Mechanical and Aerospace Engineering

NiTiHf shape memory alloys have been receiving considerable attention for high temperature and high strength applications since they could have transformation temperatures above 100 °C, shape memory effect under high stress (above 500 MPa) and superelasticity at high temperatures. Moreover, their shape memory properties can be tailored by microstructural engineering. However, NiTiHf alloys have some drawbacks such as low ductility and high work hardening in stress induced martensite transformation region. In order to overcome these limitations, studies have been focused on microstructural engineering by aging, alloying and processing.

Shape memory properties and microstructure of four Ni-rich NiTiHf alloys (Ni50.3Ti29.7Hf20, Ni50.7Ti29.3Hf20, …