Propulsion and Power Commons^™

Functional Visualizations Of A Hydrogen-Electric Aircraft Propulsion System For Supporting Pilot Decision-Making, Misha M. S. Schweitzer, Ece Üreten, Clark Borst, Olaf Stroosma, Rene Van Paassen

International Symposium on Aviation Psychology - 2025

Cognitive Work Analysis (CWA) and Ecological Interface Design (EID) were used todesign a novel flight deck display for a regional turboprop aircraft that is being retrofitted with aHydrogen Aircraft Powertrain Storage System (HAPSS). This research addresses the challengesof managing cognitive complexity in next-generation aviation systems, focusing on designinginterfaces based on system constraints which are modeled through the Abstraction Hierarchy(AH). Visualizations were discussed in interviews with subject matter experts highlighting theneed for further matching the mental model of the pilot by addressing simplicity, workload, anduse case representations on the display. The iterative process included static and dynamic displaytesting and focused on …

Hydrogen Standards And Aviation Sustainability, Eva Maleviti, Evan Stamoulis, Elen Paraschi

Publications

Standards from ISO, SAE, and ASTM are essential for certification, safety, and sustainability validation.

Hydrogen Readiness In Aviation & Challenges- Technology Meets Regulation And Market Demand, Eva Maleviti

Publications

Where technology meets regulation and market demand.

Simulation-To-Hardware Validation Of Mpc For Binary Thruster 2d Cubesat Control, Aevar Amundinusarson Oefjoerd

Theses and Dissertations--Mechanical and Aerospace Engineering

Small satellites must execute precise, fuel-limited maneuvers under strict actuation and operational constraints. Model Predictive Control (MPC) is a suitable approach because it optimizes future actions while explicitly enforcing these limits. This work evaluates (1) whether MPC can operate in real time using binary (on/off), asymmetric thrusters, and (2) whether a high-fidelity digital twin can be used to tune and validate the controller prior to hardware testing.

An MPC framework was implemented on a planar satellite prototype that floats on air bearings, operates at 16.7 Hz (60 ms period), and uses eight binary thrusters exhibiting up to 13.2% variation in …

Design Of An Active-Control Pressure Regulator For A Rocket, Seth Arkwright

Williams Honors College, Honors Research Projects

An electronically actuated pressure-regulation valve and controller are necessary for maintaining pressure levels in a pressure-fed liquid-fueled rocket engine. Mechanical regulators are too heavy and have unacceptably high-pressure variation throughout the operation of a dynamic system like a rocket. Developing an electronic pressure regulator using a PID controller is a method by which a reliable, accurate, and lightweight flow regulator can be built for use on a rocket vehicle. This work will outline the development of flow simulations, PID controller, physical valve hardware, and initial testing.

Characterization Of Krypton Performance In A Laboratory 300 W Magnetically Shielded Hall-Effect Thruster, Jacob Henry Knott

Dissertations, Master's Theses and Master's Reports

Xenon has long been the propellant of choice in Hall Thrusters; however, significant work has been performed to produce thrusters capable of utilizing alternate propellants due to xenon’s price and scarcity. Krypton is the most similar alternative propellant to xenon. This work examines the performance of a sub-kilowatt magnetically shielded Hall Thruster operating on both xenon and krypton. Krypton produced lower thrust, specific impulse, and was less efficient than xenon. Specifically, the absolute xenon-krypton efficiency gap was 6 to 24 % . Krypton’s inferior efficiency is primarily attributable to differences in mass utilization and beam divergence losses. The impacts of …

Numerical Modelling And Co-Optimization Of Gasoline Fuels For Gasoline Compression Ignition Using Multi Component Approach, Ashwin Karthik Purushothaman

Dissertations, Master's Theses and Master's Reports

Future mobility is expected to rely on a broad spectrum of powertrain technologies, including battery electric vehicles (BEVs), hybrid electric vehicles (HEVs), fuel cell electric vehicles (FCEVs) and traditional internal combustion engine (ICE) vehicles. Despite the shift toward electrification, internal combustion engines are projected to remain a key component of future powertrains, either as the primary power source or as range extenders to generate electricity in hybrid systems. As such, significant research efforts continue to focus on enhancing the efficiency and reducing the emissions of ICEs to meet increasingly stringent regulatory and environmental targets. Gasoline compression ignition (GCI) has been …

Methods Of Variability Reduction In Ramjet Fuel Injection Using Fluid-Structure Interactions, Egan J. Rigney

Honors Undergraduate Theses

The Liquid Jet in Crossflow (LJIC) method of fuel injection in ramjet engines is widely used and well-studied. However, they experience variation in their behavior at different altitudes and flight speeds due to the varied flow conditions following the inlet. This variation becomes more noticeable at high-temperature and high-speed airflow conditions. The optimized and consistent breakup of liquid fuel is a key component in ramjet engine design as there is a minimum surface area requirement of the droplets for combustion to occur. Local equivalence ratios also have a significant influence on the effectiveness of combustion. As such, researchers at the …

Novel Design And Fabrication Of A High-Speed Transient Heat Flux Sensor For Application To Rotating Detonation Engines, Zachary Todd Tallman

Graduate Theses, Dissertations, and Problem Reports (ETD)

Rotating detonation engine (RDE) combustion systems have been a topic of interest in the pressure gain combustion community for their benefits over traditional gas turbine engine combustors. However, cooling requirements for these engines are significantly higher and less predictable than those of non-detonating engines. To understand and quantify the high-speed heat transfer dynamics within an RDE, a novel high-frequency heat flux sensor is presented. This study aims to design a robust, single-sided sensor that can withstand the high temperature and harsh environment of an RDE for extended durations. Screen printing is used to deposit a layered, platinum-yttria-stabilized zirconia (YSZ) film …

Optimizing Hypersonic Scramjets: A Numerical Study Of Fuel Type And Cavity Flameholder Design Impacts On Supersonic Combustion, Delaney Baumberger

Electronic Theses and Dissertations

This thesis presents recommendations for optimizing hypersonic scramjets via a numerical study focusing on fuel type and cavity flameholder design and the impacts they have on supersonic combustion. The research is divided into two main investigations aimed at improving scramjet engine efficiency using two distinct geometrical configurations, a square cavity engine and an axisymmetric cavity engine. Each configuration is examined under Mach 2 inflow conditions to assess the role of geometric variation and fuel selection on combustion stability, flameholding, and overall performance. The first study focuses on a comparative assessment of hydrogen and ethylene as scramjet fuels to evaluate their …

Hybrid Rans-Les Analysis Of Turbulent Flame Under Near Blow-Off Condition In A Multi-Stage Swirl Combustor, Brandon O'Brien

College of Graduate Studies: Theses & Dissertations

Advances in computational resources are making computational fluid dynamics (CFD) increasingly accessible for a variety of engineering applications. However, certain complex problems, such as simulating detailed flame kinetics, remain computationally prohibitive for many users. Developing cost-effective methods to simulate these challenges would greatly benefit applications involving flame dynamics, such as turbine engines or industrial burners. This study investigates the effect of main stage swirler intensity on near lean blow-off characteristics in a multi-staged swirl combustor using Ansys Fluent. The hybrid RANS-LES turbulence model, Stress Blended Eddy Simulation (SBES) coupled with Flamelet Generated Manifold (FGM) combustion model was selected to model …

Flame Boundary Effects Of Hydrogen-Air Premixing, Alecson L. De Lima Junior

Honors Undergraduate Theses

The objective of this research was to investigate the reaction of hydrogen and heated air premixing when injected into a combusting ethylene-air crossflow, and to study the flame stabilization location with varying premixing levels. The main parameter of this investigation was the flame stabilization diagnosed through chemiluminescence, based on recorded equivalence ratio, temperature, and flame boundaries, and maintaining a constant air temperature, hydrogen and air mass flow, and momentum flux ratios. Testing was conducted at different ratios of hydrogen and air premixing achieved through alternating the distance between the point where hydrogen and air are mixed and the combusting crossflow. …

The Space Rescue Professional: Operationalizing Guardians For The Future, Benjamin Johnis, Robert Bettinger, James Dean

Faculty Publications

The escalating competition in space exploration demands a dedicated space rescue capability. This article argues for the establishment of a space rescue professional (SRP) career field within the Department of Defense and the US Space Force. By harnessing existing US Air Force combat rescue expertise and partnering with the National Aeronautics and Space Administration, the Space Force can rapidly develop a robust SRP program with the warrant officer corps as its backbone. This article addresses a critical gap in national space policy to outline a cost-effective dual-service training pipeline and SRP operational roles. Such an investment safeguards astronauts, bolsters US …