Propulsion and Power Commons^™

Thermoacoustic Effects Of A Variable Equivalence Ratio In A Single Element Methane Combustor, Carter Green

Doctoral Dissertations and Master's Theses

Combustion instability is one of the leading factors in limiting the progress and innovations of liquid rocket engines and power plants. Under certain operating conditions, unsteady heat release and acoustic wave interactions can couple and lead to instabilities, such as self-sustaining pressure oscillations, that can lead to reduced combustor performance and potentially hardware damage. In this project, the thermoacoustic effects of controlling the equivalence ratio of a single-element natural gas combustor were modeled and analyzed. The project used Fidelity Pointwise for meshing, ANSYS Fluent for modeling, ERAU VEGA HPC for computing, and MATLAB for acoustic analysis. A numerical model of …

Numerical Investigation Of Rotor-Gust Acoustic Interactions Using The Overflow Cfd Solver, Jordan Mills

Doctoral Dissertations and Master's Theses

The rapid expansion of Urban Air Mobility (UAM) necessitates high-fidelity modeling to predict and mitigate the noise signatures of electric vertical take-off and landing (eVTOL) aircraft within dense urban landscapes. A critical unknown in community-noise certification is the aeroacoustic response of rotors to unsteady inflow conditions. This research addresses this gap by investigating the aerodynamic and acoustic behavior of a representative rotor subjected to time-harmonic inflow disturbances. By establishing a robust numerical framework, this thesis quantifies the relationship between periodic atmospheric gusts and their impact on rotor performance, unsteady blade loading, and subsequent sound radiation. The research consists of a …

Effect Of Nozzle Pressure Ratio On Thrust And Flow Behavior In A Supersonic De Laval Nozzle, Esha Jain

Doctoral Dissertations and Master's Theses

Supersonic nozzles operate across a range of flow regimes. While an ideally expanded condition yields optimal thrust, practical propulsion systems rarely operate at this design point due to variations in altitude and engine operating conditions. As a result, nozzles frequently operate in off-design conditions. In overexpanded regime, where the exit pressure is lower than the ambient pressure, shock-induced separation may occur within the divergent section of the nozzle, potentially degrading nozzle performance. Understanding the aerodynamic behavior of nozzles operating under off-design conditions is therefore important for improving propulsion system performance and stability. In particular, direct thrust measurements provide a key …

Thermal Management With Supercritical Carbon Dioxide Under Extreme Applications, Devon Hardy

Doctoral Dissertations and Master's Theses

A unique challenge in thermal system design is minimizing the power required to operate cooling systems while maintaining effective heat removal. Traditional cooling systems utilize single-phase fluids where the heat transfer mechanisms are well understood. To meet a variety of cooling demands, a range of technologies are available, including microchannel forced convection, jet impingement, porous media, nanofluids, pin fin arrays, and film cooling, each offering distinct advantages and limitations. While the performance of single- or two-phase cooling systems are generally predictable, in extreme thermal environments, new cooling solutions are needed to improve overall system efficiency and reliability.

Supercritical fluids, particularly …

Numerical Study On Flow Separation And Performance Characteristics Of Slot Nozzle, Chase Charpentier

Doctoral Dissertations and Master's Theses

The altitude compensating nozzle (ACN) is a type of rocket nozzle or engine that tries to minimize the negative effects of overexpansion at low altitudes. There are many forms of ACN's but most of them are heavier than traditional bell nozzles, alter the geometry of the nozzle, which requires extensive research into optimizing the new geometry, or require complex systems that can lead to structural, heating, or material problems. Out of the ACN's, the slot nozzle is a passive ACN that builds upon the bell nozzle and requires no additional weight or complex systems.

This slot nozzle is comprised of …

Characterization Of Cooled Turbine Efficiency For Off-Design Performance Models, Alberto Garcia

Doctoral Dissertations and Master's Theses

Gas turbine performance modeling is essential for predicting engine behavior across design and off-design conditions. Yet the treatment of cooling or service flows remains inconsistent, as these streams interact with the main flow in complex ways and their contribution to turbine work depends on how they are represented in performance models. The challenge is especially present in “black-box” approaches, where only inlet and outlet conditions are known and engineers must decide whether to introduce cooling flows upstream (if performing useful work) or downstream (if not). This thesis examines how different definitions of isentropic power and cooling-flow treatment affect the apparent …

Solar Sailing Adaptive Control Around The Earth-Moon Lagrange Point L4 For Stellar Observations, Luis Mendoza Zambrano

Doctoral Dissertations and Master's Theses

To expand our knowledge about the influence of the Sun in the cislunar region, as well as our understanding of shocks due to Coronal Mass Ejections and large coronal magnetic reconnection, a solar sailing approach is proposed to separately capture lunar occultations and observe the solar corona from L₄ of the Earth-Moon system. Single and multiple shooting techniques are described along with a pseudo arc-length continuation method for preliminary orbit design. Periodic orbits in the vicinity of L₄ are obtained in the context of the Earth-Moon circular restricted three-body problem (CR3BP) and the Sun-Earth-Moon bi-circular restricted four-body problem …

Aeroacoustics Applications To Jets And Rotors, Michael Marques G.

Doctoral Dissertations and Master's Theses

Aeroacoustics plays a critical role in the advancement of propulsion technologies for both conventional and emerging aerial systems. This dissertation investigates two key topics: noise suppression in supersonic rectangular jets and rotor noise characterization in hover and ground effect. Using high-fidelity numerical simulations and theoretical analyses, this research aims to develop effective noise mitigation strategies and improve predictive methodologies.

The first part of this study focuses on the reduction of noise in supersonic rectangular jets through active control techniques. A novel approach utilizing unsteady microjet actuation at the nozzle lip is explored to disrupt the formation of large-scale turbulent structures …

Experimental Investigation Of Heat Transfer To Tightly Packed Cylinder Arrays, Cameron M. Sexsmith

Doctoral Dissertations and Master's Theses

With the increased emphasis on the development of hybrid electric aircraft and other electric driven vehicles, the thermal demand on batteries is increasing. Unique to the aviation sector is the combined need of high battery thermal loads and a light-weight thermal management system. A proposed configuration is an array of batteries directly cooled with a dielectric coolant. The knowledge of heat transfer characteristics of battery cooling is becoming an ever pressing issue due to the need to optimize volume and mass in a safe manner. Tighter spacings between batteries provide higher pack densities, however, at the cost of increased cooling …

Assessing General Propulsion Architectures For Fast Transit Times To Mars For Crewed Missions, Vivek Bhatt

Doctoral Dissertations and Master's Theses

As NASA and commercial contractors, such as SpaceX, continue to develop their programs with Artemis and Starship, respectively, it is becoming more and more apparent that the program developments are ultimately for finding a way to put humans onto Mars. However, when we approach the current timeline of going to Mars, it usually involves a 6-9 month one way trip. Due to this, human spaceflight to Mars becomes more dangerous as exposure to affects such as solar radiation, long exposure to low gravity fields, and isolation. These are some of the many hazards that come with interplanetary space travel for …

Heat Transfer To Arrays Of Oscillating Impingement Jets, Alex Q. Clay

Doctoral Dissertations and Master's Theses

In gas turbine engines, the desire to increase turbine entry temperatures has become more relevant in order to increase engine efficiency. However, materials used in these engines can only withstand temperatures that are so high. Because of this, the ability to cool hot section components will always limit operating temperatures. Impingement cooling jets have become a common way of cooling due to the high rates of heat transfer that can be achieved. However, previous research has shown that the interaction of impingement jets with cylinder wake can improve the intensity and uniformity of heat transfer. The goal of this study …

Modeling Of Rotor Wake Vortex Dynamics And Interactions In Non-Homogenous Vertiport Environments, Garrison P. Shaw

Doctoral Dissertations and Master's Theses

The current research serves to analyze and study the effects ground forces can have on the thrust performance of a propeller in multiple different configurations. The current research utilizes an open source Computational Fluid Dynamics (CFD) software known as OpenFOAM to generate calculate and visualize these runs. The model used for this experiment is a hybrid model that employs both a Unsteady Reynolds-Averaged Navier-Stokes (URANS) and a detached eddy simulation using a hybrid Large Eddy Simulation (LES) via a KomegaSSTDDES model. This model serves to save computational time as well as allow for accurate results. The three cases run are …

Development Of On-The-Fly Quasi-Steady State Approximation For Chemical Kinetics In Cfd, Abhinav Balamurugan

Doctoral Dissertations and Master's Theses

This study analyzes the feasibility of On-The-Fly Quasi-Steady-State Approximation (OTF-QSSA) application for solving chemical kinetics within Computational Fluid Dynamics (CFD) simulations, aiming to reduce the computational demand of detailed mechanisms. An algorithm that dynamically identifies and designates Quasi-Steady-State (QSS) species at specific grid locations and instances during the simulation was developed. With this information, our method pseudo-delays the advancement of concentrations for these QSS species—effectively setting their rate of concentration change to zero for a set number iteration before updating using the detailed mechanism and thereby omitting the computationally intensive processes typically required for their calculation during those skipped iteration. …

Mitigating Engine Unstart In Scramjets With Porous Bleeders, Ryan Lindley

Doctoral Dissertations and Master's Theses

The effectiveness of porous bleeders in mitigating unstart phenomena and enhancing isolator effectiveness in a hypersonic scramjet was investigated. Through computational fluid dynamics simulations, the impact of porous bleeder design parameters such as pressure jump coefficient and bleeder size on isolator effectiveness and unstart prevention was evaluated. Results indicated that porous bleeders delayed flow separation and reduced adverse pressure gradients, thereby enhancing isolator performance. Additionally, porous bleeders demonstrated promising capabilities in preventing full unstart events and mitigating oscillatory unstart phenomena.

Benchmarking Of A Sco2 Heat Exchanger Flow Loop, David Velasco

Doctoral Dissertations and Master's Theses

Heat transfer of supercritical carbon dioxide (sCO2) was studied experimentally by commissioning a sCO2 flow loop featuring a horizontal tube-in-tube counterflow heat exchanger with a circular cross section. The main objective was to establish experimental heat transfer research capabilities for sCO2 at Embry-Riddle Aeronautical University’s (ERAU) Thermal Science Lab. sCO2 experiences a drastic change in thermophysical properties near its critical point that results in unique heat transfer characteristics. The high pressures at which sCO2 exists make the large gradients in thermophysical and transport properties difficult to study, experimentally and numerically. However, understanding the heat transfer characteristics and thermophysical behavior of …

Comparative Evaluation Of Propulsive Power Transmission Technologies For High-Speed Vertical Takeoff And Landing (Hsvtol) Cargo Aircraft, Xinyu Yang

Doctoral Dissertations and Master's Theses

Designing High-Speed Vertical Takeoff and Landing (HSVTOL) cargo aircraft capable of both low downwash velocity hovering and high subsonic speed cruising presents a significant engineering challenge. This challenge, stemming from conflicting design requirements, has been substantially influenced by recent technological advancements, which have offered greater flexibility in rotor placement. Consequently, this has led to the emergence of innovative mission-specific designs that hold the potential to outperform traditional concepts. The central objective of this study is to evaluate the benefits of modern technologies for VTOL cargo aircraft and assess their performance relative to baseline VTOL aircraft. The results of this comparative …

The Influence Of Mixing Duct Length And Phase Of Flight On Wall Temperatures Of A Rocket Based Combined Cycle Engine In Ejector And Air-Augmented Modes, Jonathan Grow

Doctoral Dissertations and Master's Theses

Rocket Based Combined Cycle (RBCC) engines have been theorized as a possible means of powering launch vehicles and high-speed atmospheric vehicles. By incorporating aspects of both air-breathing and rocket propulsion, RBCC engines promise up to a 230 % increase in specific impulse over traditional chemical rocket propulsion by entraining a secondary flow of atmospheric air and mixing it with the exhaust of a rocket motor. Students within the Embry-Riddle Future Space Explorers and Developers Society (ERFSEDS) identified a
problem of excessive heating and structural failure of the mixing duct during launch and transonic flight of a student-built flight test vehicle. …

Noise And Propulsive Efficiency Interactions For Rotors And Propellers At Constant Thrust, Riccardo Roiati

Doctoral Dissertations and Master's Theses

In the emerging market of Advanced Air Mobility (AAM), aerospace companies have been designing and prototyping electric and hybrid vehicles to revolutionize travel. These vehicles must have low noise and particulate emissions while also having enough propulsive efficiency to complete the mission. This thesis aims to study the relationship between noise and propulsive efficiency as related to any aircraft equipped with an electric motor and a variable pitch rotor/propeller. The combination of the electric motor with the variable pitch propeller/rotor allows for a decoupled rotational speed and torque generation, meaning that the electric motor can generate the same amount of …

Optimal Sizing And Control Of Hybrid Rocket Vehicles, Srija Ryakam

Doctoral Dissertations and Master's Theses

In the present work, a genetic algorithm is used to optimize a hybrid rocket engine in order to minimize the propellant required for a specific mission. In a hybrid rocket engine, the mass flow rate of the oxidizer can be throttled to enhance the performance of the rocket. First, an analysis of the internal ballistics and the ascent trajectory has been carried out for different mass flow rates of the oxidizer as a function of time, for a fixed amount of oxidizer, in order to study the effect of throttling. Two equivalent problems are considered: in the first problem the …

Active Control Of Coherent Structures In An Axisymmetric Jet, Michael Marques Goncalves

Doctoral Dissertations and Master's Theses

The primary objective of this work is to develop high-fidelity simulation model for jet noise control predictions and quantify the sound reduction when an external source frequency mode excitation is imposed on the jet flow. Whereas passive approaches using mixing devices, such as chevrons, have been shown to reduce low-frequency noise in jet engines, such approaches incur a performance penalty since they result in a reduced thrust. To avoid a performance penalty in reducing jet noise, the current work investigates a open-loop active noise control (ANC) system that utilizes a unsteady microjet actuator on the nozzle lip in the downstream …

Design And Flight-Path Simulation Of A Dynamic-Soaring Uav, Gladston Joseph

Doctoral Dissertations and Master's Theses

We address the development of a dynamic-soaring capable unmanned aerial vehicle (UAV) optimized for long-duration flight with no on-board power consumption. The UAV’s aerodynamic properties are captured with the integration of variable fidelity aerodynamic analyses. In addition to this, a 6 degree-of-freedom flight simulation environment is designed to include the effects of atmospheric wind conditions. A simple flight control system aids in the development of the dynamic soaring maneuver. A modular design paradigm is adopted for the aircraft dynamics model, which makes it conducive to use the same environment to simulate other aircraft models. Multiple wind-shear models are synthesized to …

Modeling Of A Hybrid-Electric System And Design Of Control Laws For Hybrid-Electric Urban Air Mobility Power Plants, Sohail Bin Salam Lahaji

Doctoral Dissertations and Master's Theses

Advanced Air Mobility (AAM) is an emerging market and technology in the aerospace industry. These systems are being developed to overcome traffic congestion. The current designs make use of Distributed Electric Propulsion (DEP): either fully electric or hybrid electric. The hybrid engine system consists of two power sources: prime movers, such as turbine engines, and batteries. The hybrid systems offer higher range and endurance compared with the existing fully electric systems. Hybrid-electric power generation systems for AAM have different mission requirements when compared to systems used in automobiles. Therefore, there is a particular need to model hybrid-electric systems and the …

Computational Investigation Of Perforated Plate Film Cooling Utilizing Conjugate Heat Transfer, Jonathan Sippel

Doctoral Dissertations and Master's Theses

The accuracy of modern state-of-practice computational fluid dynamics approaches in predicting the cooling effectiveness of a perforated plate film-cooling arrangement is evaluated in ANSYS Fluent. A numerical investigation is performed using the Reynolds Averaged Navier Stokes equations and compared to NASA Glenn’s available Turbulent Heat Flux 4 experimental measurements collected as a part of the Transformational Tools and Technologies Project. A multiphysics approach to model heat conduction through the solid geometry is shown to offer significant improvements in wall temperature and film effectiveness prediction accuracy over the standard adiabatic wall approach. Additionally, localized gradient-based grid adaption is analyzed using the …

Unsteady Internal Ballistics Of A Hybrid Rocket, Naveen Sri Uddanti

Doctoral Dissertations and Master's Theses

With the recent progress made in the field of space tourism, hybrid rocket engines have gained a renewed interest due to their simplicity, low cost, operational flexibility, and safety. The flow in the ports of a hybrid rocket motor involves several coupled unsteady phenomena like moving walls, combustion in a boundary layer flow and mass addition along the port, through the regression of the solid fuel wall. The flow in the combustion chamber of a hybrid rocket is inherently unsteady because the geometry of the port varies as a function of space and time. In the current research, we develop …

Prediction Of Noise Associated With An Isolated Uav Propeller, Samuel O. Afari

Doctoral Dissertations and Master's Theses

The emergent field of interest in the Urban Air Mobility community is geared towards a world where aerial vehicles are commonplace. This poses the problem of the effects of the radiated noise. The present research presents an in-depth analysis of the noise generation mechanism of a propeller as a mode of propulsion of the said aerial vehicles. Numerical simulation utilizing a Hybrid Large-Eddy Simulation (LES) coupled with Unsteady Reynolds-Averaged Navier-Stokes (RANS) solver, is adopted on an isolated propeller modeled from the commercial DJI Phantom II 9450 propeller. The Spalart-Allmaras one equation turbulence model with rotation/curvature correction is used. The Farassat’s …

Optimal Battery Weight Fraction For Serial Hybrid Propulsion System In Aircraft Design, Tsz Him Yeung

Doctoral Dissertations and Master's Theses

This thesis focuses on electric propulsion technology associated with serial hybrid power plants most commonly associated with urban air mobility vehicles. While closed form analytical solutions for parallel hybrid aviation cases have been determined, optimized serial hybrid power plants have not seen the same degree of fidelity. Presented here are the analytical relationships between several preliminary aircraft design objectives and the battery weight fraction. These design objectives include aircraft weight, range, operation cost, and carbon emissions. The relationships are based on a serial hybrid electric propulsion architecture from an energy standpoint, and can be applied to hybrid aircraft of different …

Propulsive Battery Packs Sizing For Aviation Applications, Tianyuan Zhao

Doctoral Dissertations and Master's Theses

This thesis derives analytical methods for sizing the propulsive battery packs for designing an electric-driven aircraft. Lithium-Ion (Li-Ion) battery is the primary choice of battery cell chemistry in this thesis research due to its superior specific energy and market availability. The characteristics of Lithium-Ion battery cells are first determined and studied using experimental test results and manufacturers published data. Based on the design requirement to the battery system, the battery sizing will fall into one of the two sizing categories. The first category is power sizing, which requires the battery’s ability to deliver full power demanded by the electric motor. …

Optimized Thruster Allocation Utilizing Dual Quaternions For The Asteroid Sample Return Mission (Osiris-Rex), Asher Smith

Doctoral Dissertations and Master's Theses

As spacecraft require higher positional accuracy from the attitude control systems, new algorithm developments, along with sensor and actuator resolution and range improvements are necessary to achieve the desired science accuracies. For agile 6-Degrees of freedom (6-DOF) spacecraft with redundancy, the actuators are usually oversized or overpopulated to meet the desired slew requirements. Currently, most spacecraft utilize an over-actuated thruster system to produce 6-DOF control. This thesis presents a simulation of the OSIRIS-REx mission during the descent phase to the asteroid Bennu, with a focus on utilizing dual quaternion dynamics and a newly developed thruster allocation method. The dual quaternion …

Aviation Propulsive Lithium-Ion Battery Packs State-Of-Charge And State-Of-Health Estimations And Propulsive Battery System Weight Analysis, Jingsi Lilly

Doctoral Dissertations and Master's Theses

Aviation propulsive battery pack research is in high demand with the development of electric and hybrid aircraft. Accurate inflight state-of-charge and state-of-health estimations of aviation battery packs still remain challenging. This thesis puts efforts on estimating the state-of-charge, state-of-health, and remaining energy of a lithium- ion propulsive battery pack with a recursive least squares based adaptive estimator. By reading the system measurements (discharging currents and terminal voltages) with persistent excitation, the proposed estimator can determine the present internal parameters of the battery cells and further interpolate them into state-of-charge, state-of-health, and the remaining energy information. The validation results indicate that …

Variable Structure Feedback Control With Application To Spacecraft With Small Thrust Propulsion Systems, Samuel J. Kitchen-Mckinley

Doctoral Dissertations and Master's Theses

Small spacecrafts requiring small propulsion systems are becoming more popular for low Earth orbit. It is important for these research satellites to have accurate guidance and control systems. Small propulsion systems will also be beneficial for multiple small spacecrafts used future exploration expeditions beyond low Earth orbit. These small spacecrafts benefit from the simplicity of low thrust cold gas propulsion systems. Additionally, large spacecrafts using low thrust, high specific impulse propellants for main propulsion systems, such as ion engines, allow longer and more flexible missions, including Earth orbiting spacecraft and interplanetary spacecraft.

In order to extend the life of future …