Other Aerospace Engineering Commons^™

Spaceotter: A Floating Spacecraft Simulator Air Bearing Vehicle For Hardware-In-The-Loop Experiments And Research, Alexander Debartolo

Master's Theses

Growing interest in nanosatellites has increased demand for accessible ground-testing methods, which have historically been expensive and restricted. Floating Spacecraft Simulators (FSS), built around Air Bearing Vehicles (ABVs), address this gap by approximating a zero-gravity, friction-minimized environment suitable for testing spacecraft control systems, robotics, and propulsion on the ground.

This thesis presents the design, realization, and initial performance characterization of the Space Optically Tracked Testbed for Experiments and Research (SpaceOTTER) ABV, developed for the Cal Poly Space Robotics Lab. SpaceOTTER is the first step toward emulating the 3 degree of freedom (3-DOF) planar dynamics of a simulated spacecraft and is …

A Polygon Approach For Satellite Coverage Computation Problems, Caleb I. Arbreton

Master's Theses

During celestial body observation mission planning, predicted sensor coverage is a key analysis tool used by designers to inform concept of operations. It enables trade studies by applying a metric to assess how well different sensor, satellite, and constellation configurations can observe a mission's region of interest. The effectiveness of the studied components is then paramount in determining whether they are justified in the system architecture. Coverage computation becomes more difficult as sensor types and regions of interest (RoIs) deviate from simple shapes, and as problem formulations seek higher-fidelity results. These simplifications include: conical camera sensors, RoIs represented as simple, …

Development And Verification Of An Updated Thermal Model For Cal Poly's Small Thermal Vacuum Chamber, Bryce G. Leonard

Master's Theses

This thesis discusses modifications made to the Small Thermal Vacuum (TVAC) Chamber in the Space Environments Laboratory at California Polytechnic State University, San Luis Obispo, and the development and verification of an updated thermal model reflecting these changes. The chamber was redesigned to improve thermal performance, featuring a homogeneous aluminum platen coated with Aeroglaze Z306 to enhance radiative heat transfer, along with expanded data acquisition capabilities for temperature and pressure measurements.

A new thermal model of the chamber was developed in SolidWorks using a finite element approach. The model incorporates conductive and radiative heat transfer mechanisms and is configured to …

Effects Of Atomic Oxygen Exposure On Stressed Drag Sail Materials For Low Earth Orbit Applications, Nazanin Sadeghian Dezaki

Master's Theses

As low Earth orbit (LEO) has become an increasingly valuable region for satellite operations, it has grown increasingly congested. The Federal Communications Commission (FCC) deorbit regulations require satellites to be deorbited within 5 years of launch, and drag sails represent a practical means of meeting this requirement. An important consideration for drag sail design is the effect of atomic oxygen (AO) on sail materials. To address the gap in the literature regarding the behavior of stressed drag sail materials under AO exposure, a new test plate was manufactured for the California Polytechnic State University minimum atmospheric experimentation (MAX) AO chamber. …

A2s Uplink Latency Minimization For Wildfire Monitoring Systems Using Mbse And Stochastic Modeling, Luis Giovanni Wang

Master's Theses

Wildfire response depends on how quickly a detection reaches the people who act on it, and the slowest remaining step is often the link that carries an alert from a remote sensing platform to a satellite. This thesis models the latency of that link, the Air-to-Space uplink, for a wildfire-monitoring UAV that carries a Starlink terminal and sends an ALERT packet to a serving Low Earth Orbit satellite. The uplink is difficult to predict because both the UAV and the satellite move, and because the wildfire environment degrades the channel at the moment the data matters most.

The thesis uses …

Sal-E: Responsive Space Pathfinder Mission, Adrian Serniak, Kayla Wong

College of Engineering Summer Undergraduate Research Program

The main objective of the SAL-E mission is to grow the Cal Poly CubeSat Lab’s (PolySat) capabilities in rapid spacecraft design and testing, as well as to provide the current generation of students with the opportunity to design, test, integrate, and communicate with a satellite. This summer we will mainly be focusing on aspects of spacecraft test and integration, as we prepare for our satellite handoff in the Fall. Specifically, we will be conducting satellite assembly, Thermal Vacuum Chamber (TVAC) Testing, Vibrations Testing, and software validation and testing on the flight unit satellite. Students participating in this multidisciplinary SURP will …

Hybrid Machine Learning--Finite Element Solvers For Solid And Fluid Mechanics, Victor Alcantara-Arias, Spandan Suthar

College of Engineering Summer Undergraduate Research Program

The goal of this project is to develop a new class of hybrid solvers for partial differential equations (PDEs) encountered in solid and fluid mechanics that blend traditional finite element methods (FEM) with modern machine learning algorithms. While FEM solvers are well developed, they can be computationally expensive for realistic problems. Machine learning algorithms have emerged as possible new solutions to cut down the computational cost associated with expensive FEM simulations, but these are typically not interpretable. Previous work on this topic resulted in a class of fully interpretable machine learning solvers for PDEs that had two primary drawbacks: (i) …

Thermally Perfect Augmentation Of A Supersonic Inlet Design Tool That Uses Method Of Characteristics, Mario V. Guardado

Master's Theses

This work is the first in a series to augment a supersonic air inlet design tool based in Python 3 to incorporate new models that increase the range of applicability of the tool. This effort focuses on improving the thermodynamics model by incorporating a thermally perfect gas model. This tool utilizes method of characteristics to solve the governing equations for an inviscid, irrotational, isentropic, steady, supersonic flow field. Multiple test cases are used to assess the accuracy of all new models. A comparison is made between the original code’s test case for a supersonic inlet at low temperatures to verify …

Investigation Into Silicone-Silicate Conversion Due To Atomic Oxygen In The Low Earth Orbit Environment, Justin T. Self

Master's Theses

Silicones have been widely used over the years in spacecraft for a variety of functions, but atomic oxygen (AO) exposure in Low Earth Orbit causes a silicate (SiO₂) surface layer to rapidly develop on the silicone which results in a permanent change in its thermal and optical properties. Although this silicone to silicate conversion is known to occur, statistical predictions of layer formation as a function of time on orbit are not found in literature. This thesis utilized optical and scanning electron microscopy, Fourier-Transform Infrared Spectroscopy, diffuse reflectance spectroscopy, and nonlinear regression statistical techniques after RF plasma asher …

Spacecraft Attitude Control Simulator, Bricen S. Rigby

College of Engineering Summer Undergraduate Research Program

The Spacecraft Attitude Control Simulator is a single-axis attitude control platform which is intended to recreate the frictionless space environment in order to test cold-gas thruster control schemes. The overall goal of this research project was to observe settling data from the platform and compare it to simulated data. In practice, the predicted settling time was only 7% larger than observed settling time.

Cryogenic Fuel Applications To Sustainable Commercial Aircraft, Jack R. Kisling, Lillian Panning

College of Engineering Summer Undergraduate Research Program

Finding a source of clean and renewable energy is one of the greatest challenges humanity will face in the 21st century. With populations expanding, developing countries increasing their use of resources, and the rapid and alarming effects of climate change, a shift to a sustainable future is an existential prospect.

The goal of our project is to take the first steps toward getting safety procedures and lab space established, so mechanical engineering senior projects can quickly begin to experiment with cryogenic fuels. They will explore the application of cryogenic fuels to commercial aviation.

The Pressure Distribution Of Rotating Cylinders Using An Onboard Wireless Data Acquisition System, Nathan Eller

Master's Theses

This thesis presents a novel, cost-effective method for mapping the pressure distribution on a rotating cylinder in cross flow, a phenomenon central to the Magnus effect. Utilizing commercial-off-the-shelf (COTS) micro-electromechanical system (MEMS) pressure sensors, a high-resolution data acquisition system was developed and integrated into a rotating cylinder model. Compared to traditional approaches, such as slip rings or one-off designs, this method proved significantly cheaper and faster while achieving comparable or superior resolution. The experimental setup, including a modified continuous rotation technique and adaptable model design, facilitated rapid testing across a broad range of Reynolds numbers and reduced frequencies, exceeding the …

A Comparison Of Western And Eastern Soft Systems Approaches, John L. Anaya, John L. Anaya, John L. Anaya

Master's Theses

Soft System Approaches have been developed worldwide to help problem-solvers and decision-makers develop solutions to complex problems, such as aerospace systems. Soft System Approaches were designed to help lower the disorder of developing a complex system by increasing understanding of a situation. Four Soft System Approaches were investigated, two from the West and two from the East. Within the context of the paper, the West refers to thought patterns associated with thinkers and scientists in Europe and North America, and the East refers to those from and around China. The two from the West are Peter Checkland’s Soft Systems Methodology …

Development Of Load Measurement Technique For Arbitrary Shapes, Quintin J. Cockrell

Master's Theses

Obtaining aerodynamic forces and moments about all three orthogonal axes for arbitrary shapes at arbitrary orientations in a fast manner via a measurement technique specific to Cal Poly’s low-speed wind tunnel to continually obtain the forces and moments under quasi-steady conditions is explored. A Continuous Rotation Technique (CR) uses a 6-DOF load cell and stepper motor to rotate an object about an axis for a complete rotation. The forces and moments acting upon the object pass through the stepper motor and interface plates and recorded by the load cell as the object is rotated continuously a finite number of rotations. …

Development Of User Interface And Testing Harness, Jacob Amezquita, William Albertini

College of Engineering Summer Undergraduate Research Program

No abstract provided.

Disc Golf Throwing Robot, Nevada S. Schultz, Sydney M. Lewis, Erick Edmundo Daza, Rachel Alysse Greenberg, Peter M. Kean

Mechanical Engineering

Disc golf companies need better methods to test disc flight. The scope of this project is to create a disc throwing robot that can throw a disc golf driver 450-500 feet, with control over the speed, spin, and release angle. Research shows that multiple disc-throwing products exist; however, none meet the full requirements of this project. The Cal Poly senior project design team created a proof-of-concept machine. This prototype started as a two-wheel mechanism. Eventually, a third wheel was added, allowing for complete control over disc spin. The three-wheel prototype reached 62 mph when perfectly calibrated. The prototype is accurate, …

Structural Loads And Preliminary Structural Design For A World Speed Record-Breaking Turbo-Prop Racing Airplane, Matthew G. Slymen

Master's Theses

The Cal Poly SLO Turbo-Prop Racer project aims to design a world speed record-breaking aircraft, capable of flying more than 550 miles per hour on a 3-kilometer closed course. To further this endeavor, this thesis presents the calculations of load distributions across the aircraft’s wing and tail and preliminary structural estimates of primary structural components for verification of the loads calculations and for use in a future finite element model. The aircraft’s fundamental design characteristics effect on the structure of the aircraft, namely the unique Y-tail design, are first examined. Then, loads are calculated in accordance with the regulation dictated …

Developing A Light Curve Simulation Tool For Ground And Space-Based Observations Of Spacecraft And Debris, Andrew T. Ochoa

Master's Theses

A light curve is a plot of brightness versus time of an object. Light curves are dependent on orbit, attitude, surface area, size, and shape of the observed object. Using light curve data, several analysis methods have been developed to derive these parameters. These parameters can be used for tracking orbital debris, monitoring satellite health, and determining the mission of an unknown spacecraft.

This paper discusses the development, verification, and utilization of a tool that simulates light curve data. This tool models ground-based observations, space-based observations, self-shadowing geometry, tumbling debris, and controlled spacecraft. The main output from the tool is …

Soarnet, Deep Learning Thermal Detection For Free Flight, Jake T. Tallman

Master's Theses

Thermals are regions of rising hot air formed on the ground through the warming of the surface by the sun. Thermals are commonly used by birds and glider pilots to extend flight duration, increase cross-country distance, and conserve energy. This kind of powerless flight using natural sources of lift is called soaring. Once a thermal is encountered, the pilot flies in circles to keep within the thermal, so gaining altitude before flying off to the next thermal and towards the destination. A single thermal can net a pilot thousands of feet of elevation gain, however estimating thermal locations is not …

Development Of A Hybrid Particle Continuum Solver, Anthony J. Gay

Master's Theses

When simulating complex flows, there are some physical situations that exhibit large fluctuations in particle density such as: planetary reentry, ablation due to arcing, rocket exhaust plumes, etc. When simulating these events, a high level of physical accuracy can be achieved with kinetic methods otherwise known as particle methods. However, this high level of physical accuracy requires large amounts of computation time. If the simulated flow is in collisional equilibrium, then less computationally intensive continuum methods, otherwise known as fluid methods, can be utilized. Hybrid Particle-Continuum (HPC) codes attempt to blend particle and fluid solutions in order to reduce computation …

Comparing Radiation Shielding Potential Of Liquid Propellants To Water For Application In Space, John Czaplewski

Master's Theses

The radiation environment in space is a threat that engineers and astronauts need to mitigate as exploration into the solar system expands. Passive shielding involves placing as much material between critical components and the radiation environment as possible. However, with mass and size budgets, it is important to select efficient materials to provide shielding. Currently, NASA and other space agencies plan on using water as a shield against radiation since it is already necessary for human missions. Water has been tested thoroughly and has been proven to be effective. Liquid propellants are needed for every mission and also share similar …

Design And Validation Of An Led-Based Solar Simulator For Solar Cell And Thermal Testing, Matthew Gunther

Master's Theses

An LED-based solar simulator has been designed, constructed, and qualified under ASTM standards for use in the Cal Poly Space Environments Laboratory. The availability of this simulator will enhance the capability of undergraduate students to evaluate solar cell and thermal coating performance, and offers further research opportunities. The requirements of ASTM E927-19 for solar simulators intended for photovoltaic cell testing were used primarily, supplemented by information from ASTM E491-73 for solar simulators intended for spacecraft thermal vacuum testing. Three main criteria were identified as design goals - spectral match ratio, spatial non-uniformity, and temporal instability. An electrical design for an …

Secondary Uses Of Ballutes After Aerocapture, Josiah Shelton

Master's Theses

Aerocapture is a method for spacecraft orbital insertion that is currently being assessed for use in interplanetary missions. This method would use a low periapsis hyperbolic entry orbit to induce drag allowing the spacecraft to slow down without the use of a propulsion system. This is accomplished by using a ballute (balloon parachute), which is released after the appropriate change in velocity necessary to achieve the desired planetary orbit. Once released, the ballute could deploy a secondary mission vehicle. A MATLAB simulation was run to understand the environment a secondary payload would undergo, such as heating and deceleration, as well …

Thermal Modeling And Testing Of The Blue Thermal Vacuum Chamber, Madeline R. Jensma

Master's Theses

The Blue Thermal Vacuum Chamber (TVAC) located in the Space Environments Laboratory at California Polytechnic State University, San Luis Obispo (Cal Poly), may be used for thermal vacuum testing of test articles that fit with in the semi cylindrical test section that has a radius of approximately 18 cm and a length of 61 cm. The potential test articles include CubeSat systems and subsystem. The Blue TVAC can also be used for educational and research purposes. The goal of this thesis project is to develop a thermal model of the Blue TVAC to predict and analyze the thermal response of …

Safran Seat Attachment System, Craig John Kimball, Tyler Bragg, Lynette Cox

Mechanical Engineering

This final design review (FDR) document outlines the senior design project being carried out by a team of mechanical engineering undergraduate students attending California Polytechnic State University, San Luis Obispo for Safran Seats in Santa Maria, CA. The project originally was to design, build, and test a universal attachment to secure a widebody business class seat to seven aircraft models with different seat track geometry. The goal was to design, document, and create a finished product that fits design, weight, and manufacturing requirements, as well as passes static 9G FWD testing. Structural analysis, manufacturing analysis, FEA, and CAD assemblies will …

A System Architecture For Phased Development Of Remote Suas Operation, Eric Ashley

Master's Theses

Current airspace regulations require the remote pilot-in-command of an unmanned aircraft systems (UAS) to maintain visual line of sight with the vehicle for situational awareness. The future of UAS will not have these constraints as technology improves and regulations are changed. An operational model for the future of UAS is proposed where a remote operator will monitor remote vehicles with the capability to intervene if needed. One challenge facing this future operational concept is the ability for a flight data system to effectively communicate flight status to the remote operator. A system architecture has been developed to facilitate the implementation …

Performance Enhancement And Characterization Of An Electromagnetic Railgun, Paul M. Gilles

Master's Theses

Collision with orbital debris poses a serious threat to spacecraft and astronauts. Hypervelocity impacts resulting from collisions mean that objects with a mass less than 1g can cause mission-ending damage to spacecraft. A means of shielding spacecraft against collisions is necessary. A means of testing candidate shielding methods for their efficacy in mitigating hypervelocity impacts is therefore also necessary. Cal Poly’s Electromagnetic Railgun was designed with the goal of creating a laboratory system capable of simulating hypervelocity (≥ 3 km/s) impacts. Due to several factors, the system was not previously capable of high-velocity (≥ 1 km/s) tests. A deficient projectile …

Development Of A Tailored Flight Test Approach For Small Unmanned Aircraft Systems, Neil A. Wolfe

Master's Theses

This document contains the details of a study conducted to determine an effective performance flight test approach specifically for small Unmanned Aircraft Systems (sUAS). This was done by taking proven procedures and documentation from the FAA and the Air Force for manned aircraft and tailoring them specifically for use with sUAS flight test programs. A ‘sUAS Flight Testing Handbook’ was created from the proceedings to aid commercial organizations and recreational developers conducting sUAS research without access to flight test experience. A performance flight test program was conducted with the AeroVironment RQ-20 Puma sUAS using the developed approach to verify that …

Nanosatellite Launch Data-Logger (Sync), Christopher Martin Gerdom

Master's Theses

CubeSat designers are increasingly looking to incorporate delicate structures and optics into their payloads. These delicate payloads, however, may not survive the required absolute-worst-case launch vibration testing needed for flight certification. To help address this problem, and to better match testing conditions to real-world launch environments, this thesis introduces Sync, a compact 1/4U CubeSat payload designed to collect data on the vibrations and thermal environments CubeSats experience inside a deployer on the way to orbit. This data can be used to better understand the launch environment for different vehicles, and help develop new, more realistic testing guidelines that could enable …

Techedsat 7 And 8-Nasa Missions For Earth Observation, Andrew Pham

STAR Program Research Presentations

Big results can come from small satellites, and Technology Educational Satellite 8 or TES-8 is the latest small satellite in the TechEdSat series from NASA Ames Research Center. TechEdSat is a collaborative program, in which advanced university students have a chance to work directly with researchers on NASA Space Projects. Thanks to the assistance of students from several universities around the country every year, TechEdSat has helped NASA develop Nano-satellite technologies and evaluate new ideas for future spacecraft. TES-8 is the eighth satellite of the continuing TechEdSat series. On December 01, 2018 TES-8 followed a Commercial Resupply Service mission to …