Aeronautical Vehicles Commons^™

Numerical Simulation Of Turbulent Flows Past Three-Dimensional Cavities, Shivakumar Srinivasan

Mechanical & Aerospace Engineering Theses & Dissertations

Computations have been performed to simulate turbulent supersonic, transonic, and subsonic flows past three-dimensional deep, transitional, and shallow cavities. Simulation of these self sustained oscillatory flows has been generated through time accurate solutions of Reynolds averaged full Navier-Stokes equations using the explicit MacCormack scheme. The Reynolds stresses have been modeled, using the Baldwin-Lomax algebraic turbulence model with certain modifications. The computational results include instantaneous and time averaged flow properties everywhere in the computational domain. Time series analyses have been performed for the instantaneous pressure values on the cavity floor. Comparison with experimental data is made in terms of the mean …

Studies On The Interference Of Wings And Propeller Slipstreams, Ramadas K. Prabhu

Mechanical & Aerospace Engineering Theses & Dissertations

The small disturbance potential flow theory is applied to determine the lift of an airfoil in a nonuniform parallel stream. The given stream is replaced by an equivalent stream with a certain number of velocity discontinuities, and the influence of these discontinuities is obtained by the method of images. Next, this method is extended to the problem of an airfoil in a nonuniform stream of smooth velocity profile. This model allows perturbation velocity potential in a rotational undisturbed stream. A comparison of these results with numerical solutions of Euler equations indicates that, although approximate, the present method provides useful information …

An Analytical Design Procedure For The Determination Of Effective Leading Edge Extensions On Thick Delta Wings, Farhad Ghaffari

Mechanical & Aerospace Engineering Theses & Dissertations

An analyt1cal des1gn procedure for Lead1ng-Edge Extensions (LEE) has been developed for thick delta wings. This LFE device is des1gned to be mounted to a w1ng along the pseudo-stagnation stream surface associated w1th the attached flow design lift coeff1cient of greater than zero. The intended purpose of the device is to improve the aerodynamic performance of high subsonic and low super son1c aircraft at incidences above that of attached flow design lift coefficient, by us1ng a vortex system emanating along the leading edges of the device. The low pressure assoc1ated with these vort1ces would act on the LEE upper surface …

Interaction Of A Two-Dimensional Transverse Jet With A Supersonic Mainstream, Gilbert Otto Kraemer

Mechanical & Aerospace Engineering Theses & Dissertations

A experimental investigation of the interaction of a twodimensional sonic jet injected transversely into a confined main flow has been conducted. The main flow consisted of air at a Mach number of 2.9. The effects of varying the jet parameters on the flow field were examined using surface pressure and composition data. Also, the downstream flow field was examined using static pressure, pitot pressure, and composition profile data. The jet parameters varied were gapwidth, jet static pressure, and injectant species of either helium or nitrogen. The values of the jet parameters used were 0.039, 0.056,and 0.109 cm for the gapwidth …

Low Speed Handling Characteristics Of A Supersonic Transport By Eigenstructure Assignment, Michael Peter Lazar

Mechanical & Aerospace Engineering Theses & Dissertations

A synthesis procedure, based upon optimal regulator theory and eigenvalue/eigenvector assignment technique, was used in the design of a low-speed lateral control system for the SCAT-15F supersonic transport. Emphasis was placed on reducing the lateral acceleration at the pilot's station. Control laws were designed to make the aircraft handling characteristics acceptable with the exception of the lateral acceleration. It was found that a compromise between the roll performance requirements and the peak lateral acceleration requirement is needed for a successful SCAT-15F design.

Experimental Study Of Delta Wing Leading-Edge Devices For Drag Reduction At High Lift, Thomas Dwight Johnson Jr.

Mechanical & Aerospace Engineering Theses & Dissertations

Future fighter aircraft requirements specify efficient supersonic cruise and high-g maneuverability at high lift. The slender delta wing meets the first requirement but has large lift induced drag increments at high lift. One method to alleviate the drag is to control the flow at the wing leading edge (LE) by means of small LE devices, so as to maintain locally attached flow to higher angles of attack and thus increase the level of aerodynamic thrust.

The devices selected for evaluation were the fence, slot, pylon-type vortex generator (VG), and sharp leading-edge extension (SLEE). These devices were tested on a 60° …

Analytic And Experimental Studies Of A True Airspeed Sensor, Joseph Yao-Cheng Shen

Mechanical & Aerospace Engineering Theses & Dissertations

The objective of this study was to analyze and design a true airspeed sensor which will replace the conventional pitot-static pressure transducer. This sensor should have the following characteristics: the flow phenomenon is vortex procession, or the "vortex whistle", it should have no moving parts, and also is to be independent of temperature, density, altitude or humidity changes. This sensor has been designed mainly for small commercial aircraft with the airspeed up to 321.9 km/hr (200 mph).

In an attempt to model the complicated fluid mechanics of the vortex precession, three-dimensional, inviscid, unsteady, incompressible fluid flow was studied by using …

Computer-Aided Design Of Light Aircraft To Meet Certain Aerodynamic And Structural Requirements, Joanne Lynn Walsh

Mechanical & Aerospace Engineering Theses & Dissertations

Nonlinear mathematical programming techniques are applied to a particular aircraft design problem, that of determining the maximum range design for light aircraft subject to certain aerodynamic and structural requirements. Search techniques available in an existing nonlinear optimization computer program, AESOP, are applied to the design problem. Seven design variables are used to define the wing dimensions, the wing skin thickness, the cruise velocity, the amount of fuel carried, and the engine horsepower. The influence of different design requirements on the range is observed and discussed.

The Analysis Of A Subsonic Jet Issuing Perpendicular To A Freestream Flow From A Flat Plate And A Body Of Revolution, Donald R. Haberman

Mechanical & Aerospace Engineering Theses & Dissertations

An investigation was undertaken to determine the nature of the pressure region around a jet issuing perpendicular to a free stream flow from a flat plate and a cylindrical surface, and to determine the forces which resulted from such a pressure region. It was also attempted to develop an empirical relation to enable the prediction of surface pressure regions from known physical parameters.

The jet was exhausted from a 0.375 inch nozzle perpendicular to a free stream flow of about 90 ft./sec. The flow rate of the jet was then varied to give three free stream to jet velocity ratios …