Open Access. Powered by Scholars. Published by Universities.®

Aerodynamics and Fluid Mechanics Commons™

Open Access. Powered by Scholars. Published by Universities.®

Theses and Dissertations

Discipline
Institution
Keyword
Publication Year

Articles 121 - 150 of 189

Full-Text Articles in Aerodynamics and Fluid Mechanics

Flow Separation Prevention On A Turbine Blade In Cascade At Low Reynolds Number, James P. Lake Jun 1999

Flow Separation Prevention On A Turbine Blade In Cascade At Low Reynolds Number, James P. Lake

Theses and Dissertations

The problem of flow separation from a low pressure turbine blade was investigated. The operating conditions under which the separation occurred were documented through measurement of surface pressure coefficients, boundary layer velocity and turbulence profiles, total pressure loss coefficient and wake velocity momentum deficit. Three different means for reducing the losses associated with the flow separation were also investigated. A boundary layer trip, dimples, and V-grooves were studied as passive means requiring no additional energy to reduce the separation losses. The boundary layer trip was only successful for an inlet and axial chord Reynolds number of 50k with a reduction …

Go to article

Wind Tunnel Investigation Of Joined Wing Configurations, Jennifer Corneille Jun 1999

Wind Tunnel Investigation Of Joined Wing Configurations, Jennifer Corneille

Theses and Dissertations

The Air Force Research Laboratory's Munitions Directorate is looking to extend the range of its small smart bomb. One proposed idea is to retrofit the bombs with a wing kit, particularly a joined wing configuration. A typical joined wing configuration is one where the wings are positioned in such a way that they form a diamond in both plan and front views. The purpose of this study is to conduct low speed wind tunnel testing of the joined wing configuration to help determine if the joined wing is more beneficial than a single wing configuration. Configurations with differing sweep angles …

Go to article

Wind Tunnel Testing For Drag Reduction Of An Aircraft Laser Turret, Christopher H. Snyder Jun 1998

Wind Tunnel Testing For Drag Reduction Of An Aircraft Laser Turret, Christopher H. Snyder

Theses and Dissertations

This study investigated the use of aft-mounted fairings and splitter plates to reduce the drag of a half-scale aircraft laser turret. Forces, moments, and pressure distributions were measured in the AFIT 1.5-m (5-ft) wind tunnel at Reynolds numbers between 3x105 and 9x105 based on the turret diameter. Oil traces indicated the nature of the flow near the surface of the unmodified turret and the surrounding area. Tufts placed on the turret, fairings, and splitter plates showed changes in separation regions when configurations were changed. The flow around the turret was characterized by dominant vortices shedding from the top …

Go to article

Effect Of High Free Stream Turbulence On Film Cooling Using Double Row Of 30° Slant-Hole Injectors, Lilith I. Sorensen Mar 1998

Effect Of High Free Stream Turbulence On Film Cooling Using Double Row Of 30° Slant-Hole Injectors, Lilith I. Sorensen

Theses and Dissertations

In this study free stream turbulence levels from 7.3% to 17.8% are applied to film cooling over a flat plate with two rows of 30° slant holes using a wall jet as the main stream air supply and source of turbulence. Blowing ratios are varied from 0.25 to 2.0 and free stream velocities at injection range from 10 m/s to 85 m/s. A constant density ratio of 1.07 is kept throughout the experiment. Results show that for different magnitudes of blowing ratio free stream turbulence has a different influence on effectiveness. At the forward stations, where blow off was present …

Go to article

The Influence Of Surface Roughness On Supersonic High Reynolds Number Turbulent Boundary Layer Flow, Robert M. Latin Mar 1998

The Influence Of Surface Roughness On Supersonic High Reynolds Number Turbulent Boundary Layer Flow, Robert M. Latin

Theses and Dissertations

A comprehensive study of rough-wall high speed (M=2.9) high Reynolds number (Re/m = 1.9 x 107) turbulent boundary layer flow was performed consisting of experimental, analytical, and numerical methods. Six wall topologies consisting of a smooth and five rough surfaces (two and three dimensional machined roughness plates; and 80, 36, and 20 grit sand-grain roughened plates) were studied. A confocal laser scan microscope was used to measure the topography of the sand grain roughnesses. The experimental measurement techniques included a convention Pitot pressure probe, laser Doppler velocimetry, hot wire anemometry; color schlieren and laser …

Go to article

Analysis Of Turbulence Models As Applied To Two- And Three-Dimensional Injection Flows, Clarence R. Chenault Mar 1998

Analysis Of Turbulence Models As Applied To Two- And Three-Dimensional Injection Flows, Clarence R. Chenault

Theses and Dissertations

A steady state solution of the full, three dimensional Favre averaged Navier Stokes equations, coupled with a second order Reynolds stress turbulence model (RSTM) and an eddy viscosity model were used to numerically simulate oblique injection into supersonic flow. Numerical results were compared to experimental data and the turbulence models were evaluated for accurate prediction of thermomechanical mean flow variables, Reynolds stresses, flowfield shock structure and boundary layer phenomena. The RSTM simulation resulted in physically consistent and accurate predictions for the mean flow and turbulent quantities. Simulations with the eddy viscosity model resulted in non-physical and inconsistent turbulence predictions. RSTM …

Go to article

Experimental Investigation Of The Influence Of Molecular Weight On Mixing And Penetration In Supersonic Dissimilar Gaseous Injection Into A Supersonic Cross-Flow, Troy A. Giese Dec 1997

Experimental Investigation Of The Influence Of Molecular Weight On Mixing And Penetration In Supersonic Dissimilar Gaseous Injection Into A Supersonic Cross-Flow, Troy A. Giese

Theses and Dissertations

In pursuit of a more efficient and effective fuel-air mixing for a SCRAMjet combustor, this study investigated relative near field effects of molecular weight on mixing and penetration of different gaseous injection into a supersonic (M=2.9) cross flow. Helium and argon gas were chosen as injectants because of the large differences in molecular weights. Also, mixing enhancement was observed by injecting the traverse gas jet parallel to the compression face of a ramp. Color schlieren photography was used to identify the shock structures and interactions in the flow field. Measurements of mean flow properties were used to establish the jet …

Go to article

Flow Field And Loading Analysis On A Wrap-Around Fin Missile, Thomas C. Mcintyre Dec 1997

Flow Field And Loading Analysis On A Wrap-Around Fin Missile, Thomas C. Mcintyre

Theses and Dissertations

Wrap-around fin (WAF) missiles offer packaging benefits but experience rolling moments due to the curved fin design. Rolling moments stabilize unguided projectiles, but cause guidance and control problems for future guided applications. Understanding the flow field in the vicinity of the fins is critical to future missiles. Fin pressure profiles were characterized with pressure-sensitive paint. Two rectangular four-fin constructions were tested-one solid and one with a rectangular hole (slotted fin). Static pressure data were divided by free-stream total pressure for presentation. Tests were conducted at Mach numbers of 2.15, 2.28, 2.41, 2.86, 3.25, 3.50 and 3.83. Reynolds numbers based on …

Go to article

Numerical And Experimental Investigation Of The Flowfield Near A Wrap-Around Fin, Carl P. Tilmann Mar 1997

Numerical And Experimental Investigation Of The Flowfield Near A Wrap-Around Fin, Carl P. Tilmann

Theses and Dissertations

A wall-mounted semi-cylindrical model fitted with a single wrap-around fin (WAF) has been investigated both numerically and experimentally, with the objective of characterizing the mean and turbulent flowfield in the vicinity of the fin. Numerical and experimental results are used to determine the nature of the flowfield and quantify the effects of fin curvature on the character of the flow near WAFs. This research has been motivated by the need to identify possible sources of a rolling moment reversal observed at high speeds in sub-scale flight tests. Detailed mean flow and turbulence measurements were obtained in the AFIT Mach 3 …

Go to article

Experimental Investigation Of Compressible Boundary Layers Under The Influence Of Pressure Gradients, Raymond C. Wier Dec 1996

Experimental Investigation Of Compressible Boundary Layers Under The Influence Of Pressure Gradients, Raymond C. Wier

Theses and Dissertations

This study examined the effect of mild pressure gradients on the mean and turbulent flow of high-speed boundary layers. Three Mach numbers (1.7, 3.0 and 5.0) were investigated. Three pressure gradients were examined; a zero pressure gradient (ZPG), a favorable pressure gradient (FPG), and a combined pressure gradient (CPG). The CPG consisted of an adverse pressure gradient followed by a favorable pressure gradient. Conventional pressure probes, hot-wire and particle image velocimetry (PIV) were used to examine the flow. Measurement included mean velocity, velocity turbulence intensity, mass flux turbulence intensity and energy spectra. Instantaneous (10 nsec) Mie scattering flow visualizations were …

Go to article

Experimental Investigation Of Transverse Supersonic Gaseous Injection Enhancement Into Supersonic Flow, Mark P. Wilson Dec 1996

Experimental Investigation Of Transverse Supersonic Gaseous Injection Enhancement Into Supersonic Flow, Mark P. Wilson

Theses and Dissertations

In pursuit of more efficient and effective fuel-air mixing for a SCRAMJET combustor, this study was conducted to investigate relative near field enhancements of penetration and mixing of a discrete low-angled (25°) injected air jet into a supersonic (M=2.9) cross flow. The enhancements were achieved by injecting the transverse air jet parallel to the compression face of eight different ramp geometries. The jet-ramp interactions created collinear shock structures, baroclinic torque vorticity enhancement, ramp spillage enhanced vorticity, magnus effect penetration enhancement, and increased total pressure loss. Shadowgraph photography was used to identify the shock structures and interactions in the flow field. …

Go to article

Direct Measurement Of Skin Friction In High Temperature And Impulsively Started Supersonic Flowfields, David M. Hazelton Jun 1996

Direct Measurement Of Skin Friction In High Temperature And Impulsively Started Supersonic Flowfields, David M. Hazelton

Theses and Dissertations

This study further developed and improved a miniature plastic cantilever floating element gauge for direct measurement of skin friction in shock tunnel tests. Gauge durability and usability were improved, and potential sources of error were quantified. A high frequency 30 kHz gauge (compared to the baseline 10 kHz gauge) was constructed by using an I-beam cantilever rather than a round beam. A directional gauge was developed and demonstrated by measuring the flowfield about a fin in the AFIT shock tunnel. The 10 kHz and 30 kHz gauges were used in two scramjet test sequences conducted at Mach 14 enthalpy (stagnation …

Go to article

Nonlinear Analysis Of Airfoil Flutter At Transonic Speeds, Scott A. Morton May 1996

Nonlinear Analysis Of Airfoil Flutter At Transonic Speeds, Scott A. Morton

Theses and Dissertations

Hopf-bifurcation analysis is used to determine flutter boundaries of a pitch and plunge airfoil (PAPA) at transonic Mach number conditions. The PAPA model is a coupling of the Euler equations and a two-degree-of-freedom structural model composed of linear and torsional springs. The Euler equations are discretized using an upwind total variation diminishing scheme (TVD) of Harten and Yee. Equilibrium solutions of the PAPA model are computed using Newton's method and dynamic solutions are explicitly integrated in time with first-order accuracy. The Hopf-bifurcation point, which models the flutter condition, is computed directly by solving an extended system of equilibrium equations following …

Go to article

An Investigation Into The Effects Of Lateral Aerodynamic Asymmetries, Lateral Weight Asymmetries, And Differential Stabilator Bias On The F-15 Directional Flight Characteristics At High Angles Of Attack, David R. Evans Mar 1996

An Investigation Into The Effects Of Lateral Aerodynamic Asymmetries, Lateral Weight Asymmetries, And Differential Stabilator Bias On The F-15 Directional Flight Characteristics At High Angles Of Attack, David R. Evans

Theses and Dissertations

The F-15 is a stable aircraft throughout most of its flight envelope. However, it still exhibits an uncommanded yawing and rolling tendency at high angles-of-attack. Identified influencing factors of this uncommanded motion are lateral aerodynamic asymmetries, lateral weight asymmetries, and differential stabilator bias. Previous research into the effects of these influencing factors has been qualitative. This thesis quantifies the effects and then identifies a symmetric F-15 configuration. The quantifying metric presented is net yaw acceleration. This thesis used both computer simulation and experimental flight test to quantify these effects. A discussion of each influencing factors effects on the F-15B high …

Go to article

Compressible Turbulence Measurements In A Supersonic Boundary Layer With Impinging Shock Wave Interaction, Michael J. Meyer Mar 1996

Compressible Turbulence Measurements In A Supersonic Boundary Layer With Impinging Shock Wave Interaction, Michael J. Meyer

Theses and Dissertations

No abstract provided.

Go to article

Riblet Effects On Gortler Vortex Development Over A Concave Surface, James A. Rothenflue Feb 1996

Riblet Effects On Gortler Vortex Development Over A Concave Surface, James A. Rothenflue

Theses and Dissertations

Riblet effects on Goertler vortex development in laminar and transitional flows were measured using three-dimensional laser-Doppler anemometry. Three freestream velocities were tested such that riblet spacing corresponded to Goertler vortex (GV) wavelengths which presumably would be either strongly amplified, weakly amplified, or attenuated by centrifugal forces on a curved surface. Experiments revealed the development of paired, counterrotating vortices within the riblet valleys over both flat and concave surfaces. For riblet spacings equivalent to weakly or non-amplified GV wavelengths, GV development on a curved surface was above the riblets and was delayed by the addition of riblets. The GV wavelength was …

Go to article

An Experimental Investigation Of A Sting-Mounted Finite Circulation Control Wing, Lorenzo C. Bradley Iii Dec 1995

An Experimental Investigation Of A Sting-Mounted Finite Circulation Control Wing, Lorenzo C. Bradley Iii

Theses and Dissertations

This study investigated the lift, drag and pitching moment performance of a circulation control wing in the AFIT 5-ft wind tunnel. The experimental wing model was a 20 percent thick, 8.5 percent camber, partial elliptical cross-section, single blowing slot, rectangular planform wing. The aspect ratios tested were 3.99, 3.77 and 3.75. The variables in the investigation included the slot blowing rate and model configuration. The model was modified by adding a leading edge nose droop, a trailing edge splitter plate and wing tip fences to improve flow at the leading edge, reduce separation effects, and encourage attached flow on the …

Go to article

Influence Of A Moving Endwall On The Tip Clearance Vortex In An Axial Compressor Cascade, Lawrence J. Peter Dec 1995

Influence Of A Moving Endwall On The Tip Clearance Vortex In An Axial Compressor Cascade, Lawrence J. Peter

Theses and Dissertations

This experiment involved the design, construction, validation and testing of a new facility for the investigation of vortices generated by compressor rotor blade tip clearance with a moving endwall. A five-tube pressure rake placed downstream of the trailing edge of a cascade of blades measured the pressure field for flow coefficients ranging from 20 to 1.66 and tip clearances of 0.33, 1.0, 1.7 and 2.4 percent chord. Contour plots of mass averaged pressure loss coefficient appear to show the no-flow tip vortex becomes entrained and diffused by the moving wall boundary layer. The high loss region near the moving wall …

Go to article

Investigation Of Aerodynamic Alterations For Improving The Kc-135 Boom Performance During Aerial Refueling, Debra A. Nawrocki Dec 1995

Investigation Of Aerodynamic Alterations For Improving The Kc-135 Boom Performance During Aerial Refueling, Debra A. Nawrocki

Theses and Dissertations

This study investigated the eligibility of the KC-135 air refueling boom for improved capabilities in the areas of control and performance. By using a thick airfoil cross-section for the boom tube, rather than the current circular cross-section, the ability to increase the lift characteristics was verified Prior compiled test data was used for comparison against analytical computer solutions. The possibility and effects of control frequency oscillations were also examined due to the unstable nature of the flow at test conditions. Additionally, the effect of other cross-section shapes, such as the blunt fairing, on the size of the flyable envelope for …

Go to article

Experimental Investigation Of Non-Adiabatic Supersonic Slot Injection Into A Supersonic Cross-Flow, Kelly C. Tucker Dec 1995

Experimental Investigation Of Non-Adiabatic Supersonic Slot Injection Into A Supersonic Cross-Flow, Kelly C. Tucker

Theses and Dissertations

Turbulence and mean flow measurements were acquired downstream of a normal, supersonic (M=1.6), two-dimensional, slot injection into Mach 3.0 flow (Re/m = 15x106). Two non-adiabatic cases Ti/T∞ = 1.11 and Ti/T∞ = 0.93) were studied. Multiple overheat anemometry and conventional mean flow analysis, as well as shadowgraph and schlieren photography, were utilized to study the turbulent mixing layer. The mean flow data included the Pitot, cone-static, and Mach number profiles. The measured turbulence data included shear stresses, mass flux, total temperature turbulence intensities, and turbulent heat fluxes. The temperature and density variation …

Go to article

Numerical Simulation Of Supersonic Turbulent Boundary Layer Flow Under The Influence Of Mild Pressure Gradients, Eric T. Fick Dec 1995

Numerical Simulation Of Supersonic Turbulent Boundary Layer Flow Under The Influence Of Mild Pressure Gradients, Eric T. Fick

Theses and Dissertations

Mach 2.9 boundary layer flow (Re/m ≈ 1.75x107) under the influence of mild pressure gradients is studied numerically. Baldwin-Lomax and k - ω turbulence models are incorporated into a cell centered finite volume flow solver and the results are compared with hot wire anemometry and Laser Doppler Velocimetry (LDV) measurements obtained for the same geometries in the AFIT Mach 2.9 wind tunnel. Agreement between the present simulations obtained with the k - ω turbulence model and experimental velocity profiles is excellent in all test sections. Nondimensional turbulent shear stress predictions closely match experimental data in the …

Go to article

Experimental Investigation Of A Supersonic Turbulent Boundary Layer With Adverse Pressure Gradient, Chad S. Hale Dec 1995

Experimental Investigation Of A Supersonic Turbulent Boundary Layer With Adverse Pressure Gradient, Chad S. Hale

Theses and Dissertations

Laser Doppler Velocimetry (LDV) measurements were made to quantify the effect of adverse pressure gradient on the compressible turbulent flow structure in a Mach 2.9 boundary layer (Re/m= 1.75 x 107). Measurements included profiles of 2-D mean velocities, turbulence intensities, Reynolds shear stresses, intermittency, flatness and skewness. In addition, mean strain rates were also measured. The boundary layer measurements were acquired for both flat plate and compression ramp models. LDV measurements were made at two locations on the compression ramp model at 68 cm and 71 cm downstream of the nozzle throat. At these locations, Β …

Go to article

Mach 2.9 Investigation Into The Flow Structure In The Vicinity Of A Wrap-Around Fin, Richard E. Huffman Jr. Dec 1995

Mach 2.9 Investigation Into The Flow Structure In The Vicinity Of A Wrap-Around Fin, Richard E. Huffman Jr.

Theses and Dissertations

A ceiling-mounted semi-cylindrical model containing a single wrap-around fin (WAF) was tested in the AFIT Mach 2.9 test facility. Flow visualization using oil- low streaklines, schlieren images and shadowgraph photography revealed a A-shock at the fin-body juncture and the development of an asymmetric bow-shock about the fin. Quantitative measurements were taken with a 100 cone-static pressure probe, a Pitot pressure probe and two cross-wire hot-film probes (u-v and u-w components, respectively). Measurements were made at cutting-planes from the inlet of the test section to aft of the model, with emphasis placed in the vicinity of the WAF. Results include cutting-plane …

Go to article

Compressible Turbulence Measurement In The Mixing Layer Of An Adiabatic Normal Slot Injection Into Supersonic Flow, Christopher D. Whitcomb Dec 1995

Compressible Turbulence Measurement In The Mixing Layer Of An Adiabatic Normal Slot Injection Into Supersonic Flow, Christopher D. Whitcomb

Theses and Dissertations

In this study mean flow and compressible turbulence measurements were taken at a station x = 72W downstream of the injection, where W is the injector throat width, of an adiabatic 2-D Mach 1.6 normal slot injection into a Mach 2.9 flow. Data were collected using a conventional Pitot probe, a cone-static probe, and multiple overheat cross-wire anemometry. In addition, schlieren and shadowgraph flow visualization was used to investigate the flow structure at both the injection point and at the downstream data collection point. From these measurements, mass flux component turbulence intensities of 8% to 10% were seen. The total …

Go to article

Development And Testing Of A New Optimum Design Code For Hypersonic Wind Tunnel Nozzles, Including Boundary Layer, Turbulence, And Real Gas Effects, Ralph C. Tolle Nov 1995

Development And Testing Of A New Optimum Design Code For Hypersonic Wind Tunnel Nozzles, Including Boundary Layer, Turbulence, And Real Gas Effects, Ralph C. Tolle

Theses and Dissertations

A robust and efficient optimization code is developed and validated. The code is used to redesign an existing Mach 12 wind tunnel nozzle and utilizes response surface methodology (RSM) techniques. Explicit, globally second-order, flux-difference-splitting algorithms are used to solve the Navier-Stokes (NS) and Parabolized Navier-Stokes (PNS) flow solvers incorporated into the optimizer code. Either the Baldwin-Lomax or the Yang-Shih k-s turbulence model may be employed in the optimization code. First, 2-D/axisymmetric NS and PNS flow solvers are developed/modified and account for perfect gas/nonequilibrium chemically reacting flows. All solvers are validated against Computational Fluid Dynamics (CFD) and experimental data. The optimization …

Go to article

Compressible Turbulence Measurement In Low-Angle Injection Into A Supersonic Flow, Gregory J. Mccann Mar 1995

Compressible Turbulence Measurement In Low-Angle Injection Into A Supersonic Flow, Gregory J. Mccann

Theses and Dissertations

Mean flow and compressible turbulence measurements have been obtained at two stations downstream of low-angle supersonic injection into a Mach 3.0 flow (Re/m = 15 x 106). Data were collected using conventional Pitot and cone-static probes, single and multiple overheat cross-wire anemometry, and flow visualization techniques (shadowgraphs and schlierens). A direct measure of total Reynolds shear stress was accomplished using a turbulence transformation of the Reynolds-averaged Navier-Stokes equations. Results show compressibility effects, indicated by density fluctuations, to be large relative to the velocity fluctuations and on the same order in all three components. Compressibility appears to account for …

Go to article

Compressible Turbulence Measurements In A Supersonic Flow With Adverse Pressure Gradient, Jon W. Dotter Dec 1994

Compressible Turbulence Measurements In A Supersonic Flow With Adverse Pressure Gradient, Jon W. Dotter

Theses and Dissertations

Mean flow and compressible turbulence measurements have been obtained upstream and within a shock boundary interaction and a compression ramp in Mach 3 flow. Compressible turbulence models have met with little success in the accurate prediction of high-speed flows involving complicated shock boundary interactions and adverse pressure gradients because of a crucial lack of experimental data. Data were collected using conventional Pitot and cone static probes, single overheat cross-wire anemometry, multiple overheat cross-wire anemometry, and flow visualization techniques. Direct measurements of the total Reynolds shear stress were obtained using a turbulence transformation. Results indicate that compressibility effects, as evidenced by …

Go to article

Investigation Of Boundary Layer And Performance Effects Of Transpiration Cooling Through A Porous Plate In A Rocket Nozzle, David N. Keener Dec 1994

Investigation Of Boundary Layer And Performance Effects Of Transpiration Cooling Through A Porous Plate In A Rocket Nozzle, David N. Keener

Theses and Dissertations

This study used a range of low blowing ratios with air through an area of porous material in a Mach 2.0 nozzle to quantity the change in boundary layer thickness as a function of blowing ratio. Also, exit and wall Mach number profiles at each blowing ratio were collected to characterize performance losses as a result of blowing. Performance in terms of specific impulse was also studied. As expected, the boundary layer thickness increased and nozzle performance in terms of exit Mach number decreased with increasing blowing ratio.

Go to article

The Design And Development Of A Low-Speed, Low-Force Wind Tunnel Data Acquisition System With An Application To Bicycle Front Fork Spacing, Alan W. Elledge Dec 1994

The Design And Development Of A Low-Speed, Low-Force Wind Tunnel Data Acquisition System With An Application To Bicycle Front Fork Spacing, Alan W. Elledge

Theses and Dissertations

This thesis encompassed the design, development, and application of a low-speed, low-force data acquisition system for the AFIT 5-ft Wind Tunnel. The new data acquisition system was designed and developed to measure approximately 0.045 N (about 0.01 lbf) at nearly 64.4 km/h (40 mph). Verification of the capability was obtained through testing of a cylindrical model. As part of a technology transition program with Wright Laboratory, this new system was used to investigate bicycle front fork blade spacing in order to determine the optimal spacing for minimum drag. As for the minimum drag of a bicycle with an …

Go to article

An Experimental Study Of Planar Heterogeneous Supersonic Confined Jets, Frederick J. Tanis Jr. Dec 1994

An Experimental Study Of Planar Heterogeneous Supersonic Confined Jets, Frederick J. Tanis Jr.

Theses and Dissertations

The effects of varying the exit pressure of a supersonic helium jet exhausting coaxially with two parallel supersonic air streams into a constant area duct were investigated. The method used to evaluate the mass entrainment rate was to measure helium molar concentration profiles and mass flux across the duct using a binary gas probe then calculate the mass entrainment into the helium jet. In order to conduct this study a novel binary gas probe was developed which allowed helium concentration and mass flux data to be obtained during continuous traverses across the supersonic flowfield. High exit pressure ratio (EPR) led …

Go to article

First Prev Next Last