Aerodynamics and Fluid Mechanics Commons^™

Design And Optimization Of A Bluff Body For Energy Harvesting Of Transverse Galloping Induced By Low-Speed Wind Using Bernstein Polynomial Equations, Youssef Wael Abdelmoneim

Theses and Dissertations

In this thesis, a computational framework is proposed for optimizing the aerodynamic shape of bluff bodies used in galloping-based wind energy harvesters. The system targets low-wind speed environments, where normal wind turbines are not effective, offering a potential alternative to batteries used for powering small electronic devices such as wireless sensors. The design relies on the galloping effect, where airflow around a bluff body induces transverse oscillations that drive an energy conversion mechanism. To generate efficient bluff body geometry, the Class-Shape Transformation (CST) method is used to define a wide range of candidate shapes with minimal design parameters. These shapes …

Multi-Fidelity Machine Learning Modeling For Aerodynamic Response Prediction Of Aerospace Vehicles, Ethan S. Jackman

Theses and Dissertations

Hypersonic vehicle design requires understanding complex aerodynamic phenomena across the full flight regime. This study presents a novel MF surrogate modeling methodology that enables the prediction the full field response across a vehicle’s surface. A Space-Filling Curve (SFC) is used to convert unstructured data into 1D vectors. The a Convolutional Autoencoder is used with transfer learning to reduce the dimensionality of the data. An Emulator-Embedded Neural Network (E2NN) combines multi-fidelity data for fast, accurate predictions. A benchmark analytical example and hypersonic application are used to evaluate the methodology. Using various numbers of samples and sampling strategies it is found that …

An Investigation Into In-Flight Loss Of Control Accidents Due To Horizontal Stabilizer Changes On The Piper Cherokee, Connor John Geran

Theses and Dissertations

Loss of Control (LOC) while in-flight in General Aviation (GA) has been the subject of intense research by academic institutions and regulatory agencies in recent years [4] [9] [11] [19] [20] [21]. This interest is primarily due to a disproportionate number of all aircraft accidents occurring within the GA category of flight, with 94% of accidents in 2022 occurring within GA, caused primarily by pilot LOC, with 42% of accidents having LOC as the listed cause. Research into this subject at FIT yielded the results that many common GA aircraft tend to experience a strong pitch up response after undergoing …

Experimental And Numerical Analysis Of Laminar And Transitional Flow Through Annular Corrugated Pipes, Joseph Russell Sargent

Theses and Dissertations

This dissertation presents studies on pressure loss through annular corrugated pipes to determine a friction factor coefficient using nitrogen. Ten different corrugated pipes’ geometries were evaluated via testing and experimentation. The ratio of corrugation height to inner diameter varied from 0.233 to 0.333 and the ratio of corrugation pitch to inner diameter varied from 0.181 to 0.446. Nitrogen flow rates between 0.25 to 94.4 standard liters per minute were used, resulting in Reynolds numbers, based on the corrugated pipe inner diameter, from 100 to 23,000. The experimental set-up was validated using smooth-pipe pressure loss measurements and the derived friction factor …

Aerodynamic Investigation Of Naca 0020 Airfoil With Extended And Serrated Trailing Edge At Various Turbulent Intensities, Livya E

Theses and Dissertations

Lift (upward force) is a significant aerodynamic component that directly relates to the aerodynamic efficiency (lift-to-drag ratio) of the airfoil. Enhancement of airfoil lift is important for industries like wind turbines, aircraft, and turbo machinery. The present study investigates the NACA series airfoil by modifying the trailing edge in the form of extension and serration. The angle of attack was changed from 0° to 35° instep of 5°, and the airflow Reynolds number was fixed as 2.14 × 105. To figure out the flow behavior, surface pressure has been collected from the 50 pressure ports provided over the airfoil surface. …

Fluid Flow And Thermal Performance Investigation Of Twisted Elliptical Tubes For Use In High Prandtl Number Systems, Connor F. Donlan

Theses and Dissertations

The development of clean energy systems is paramount to reducing mankind's climate impact. These clean energy systems include solar, wind, and nuclear power where nuclear power shows a reduced lifetime carbon dioxide footprint per kilowatt hour compared to other sources [102]. Advanced nuclear reactors, fusion energy systems, and concentrated solar power designers are looking at using molten salt heat transfer fluids and improved heat exchanger design to increase power production and efficiency of clean energy systems. The improving heat transfer within the main heat transfer components within advanced nuclear reactors will enable increased efficiencies and power production.

Heat transfer improvements …

Investigation And Control Of Görtler Vortices In High-Speed Flows, Omar Es-Sahli

Theses and Dissertations

High-amplitude freestream turbulence and surface roughness elements can excite a laminar boundary-layer flow sufficiently enough to cause streamwise-oriented vortices to develop. These vortices resemble elongated streaks having alternate spanwise variations of the streamwise velocity. Following the transient growth phase, the fully developed vortex structures downstream undergo an inviscid secondary instability mechanism and, ultimately, transition to turbulence. This mechanism becomes much more complicated in high-speed boundary layer flows due to compressibility and thermal effects, which become more significant for higher Mach numbers. In this research, we formulate and test an optimal control algorithm to suppress the growth rate of the aforementioned …

Investigation Of Hypersonic Near-Wake Relaminarization Over A 7 Degree Half-Angle Cone, Jesse L. Roberts

Theses and Dissertations

To investigate the potential for relaminarization in the near-wake of a 7-degree half-angle cone, a series of hypersonic wake experiments were conducted in the Air Force Research Laboratory Mach 6.1 Ludwieg tube. Relaminarization is a spatial phenomenon that occurs when a turbulent flow reverts to a laminar-like state at a downstream location, where turbulent fluctuations negligibly contribute to average flow properties. Although relaminarization has been documented in subsonic and supersonic flows, the current body of knowledge related to the occurrence of, and mechanisms that drive, relaminarization at hypersonic speeds is sparse. Measurements were obtained across a range of freestream unit …

Quasi 1d Modelling Of A Scramjet Engine Cycle Using Heiser-Pratt Approach, Asmaa Chakir

Theses and Dissertations

Scramjet engines are key for sustained hypersonic flights. Analytic models play a critical role in the preliminary design of a scramjet engine configuration. The objective of this research is to develop and validate a quasi-1D model for the scramjet engine encompassing inlet, isolator and combustor, to evaluate the impact of flight conditions and design parameters on the engine functionality. The model is developed assuming isentropic flow in the inlet with a single turn; modified Fanno-flow equations in the isolator that account for the area change of the core flow; and the combustor is modeled using Heiser-Pratt equations accounting for the …

Experiments To Mitigate Flow Recirculation In A Closed Anechoic Chamber Using Mesh Screens As Turbulence Suppressors, Tori Kay Wolverton

Theses and Dissertations

The desire to gather acoustic data of a propeller in simulated hover without environmental effects is met with the challenge of recirculating flow in a closed anechoic chamber. Flow recirculation in an anechoic chamber is not ideal because the effects of it being ingested by the rotor cause unsteady loadings on the propeller. This unsteady loading causes vortex noise from the turbulence introduced by the recirculation of the flow. The aim is to study the acoustic signature of a propeller separate from external factors and engine noise. Two different propellers with three different screen combinations were tested in a closed …

Direct Simulation And Reduced-Order Modeling Of Premixed Flame Response To Acoustic Modulation, Zheng Qiao

Theses and Dissertations

This dissertation introduces a general, predictive and cost-efficient reduced-order modeling (ROM) technique for characterization of flame response under acoustic modulation. The model is built upon the kinematic flame model–G-equation to describe the flame topology and dynamics, and the novelties of the ROM lie in i) a procedure to create the compatible base flow that can reproduce the correct flame geometry and ii) the use of a physically-consistent acoustic modulation field for the characterization of flame response. This ROM addresses the significant limitations of the classical kinematic model, which is only applicable to simple flame configurations and relies on ad-hoc models …

Exploratory Measurement Of Recession Rates Of Low Temperature Ablators Subjected To Mach 6 Flow, Ross H. Kellet

Theses and Dissertations

The high speed/high-temperature effect of heat shield ablation was simulated in the low-enthalpy AFRL Mach 6 Ludwieg Tube using solid dry ice as a low-temperature sublimator. The experiments utilized both 21 half-angle cones and bi-conic models with a 7 ° half-angle leading edge followed by a 26° half-angle base contained within a cryogenic-cooled stainless steel holder. A method of fabricating dry ice test articles was developed using commercially procured dry ice and custom-made aluminum molds. Tests were performed at Mach 6.1 with a stagnation temperature of 490 K and stagnation pressures ranging from 40 - 500 psi. Unit Reynolds number …

Characterizing Wake Roll-Up And Vortex Structure For Delta Wing Configuations Featuring Flow Control Devices At Low Reynolds Number, Jeffrey M. Layng

Theses and Dissertations

Various configurations of a cropped delta wing featuring a NACA 0012 wing-section were evaluated experimentally at a Reynolds number of 5.0 x 10⁵ in the Air Force Institute of Technology Low-Speed Wind Tunnel facility. The effects of active flow control (AFC) and passive boundary-layer fences (BLF) were shown to improve high angle of attack delta wing performance. The AFC BLFs were shown to replicate the performance enhancements found in passive BLFs without incurring a drag penalty. An experimental characterization of the wake region is presented to compare the wake roll-up and leading edge vortices for these baseline, passive BLF, …

Fluid-Structure Interaction Of Nrel 5-Mw Wind Turbine, Mohamed Sayed Elkady Abd-Elhay

Theses and Dissertations

Wind energy is considered one of the major sources of renewable energy. Nowadays, wind turbine blades could exceed 100 m to maximize the generated power and minimize produced energy cost. Due to the enormous size of the wind turbines, the blades are subjected to failure by aerodynamics loads or instability issues. Also, the gravitational and centrifugal loads affect the wind turbine design because of the huge mass of the blades. Accordingly, wind turbine simulation became efficient in blade design to reduce the cost of its manufacturing. The fluid-structure interaction (FSI) is considered an effective way to study the turbine's behavior …

Optimizing Design Parameters For Active Flow Control Boundary-Layer Fence Performance Enhancement On A Delta Wing, Nathan L. Tedder

Theses and Dissertations

Utilizing computational fluid dynamic (CFD) simulations, the presented study is able to further the investigation of replicating and improving upon the performance of a NACA 0012 cropped half-span delta-wing at high angles-of-attack with an active flow control fluidic fence via wall-normal, steady blowing from an optimized single chordwise slot located at z/b = 70%,. The data is generated using CREATE-AV Kestrel v10.1rc5 CFD software on the Department of Defense High Performance Computing systems. The flight regime is held constant at a Mach number of 0.18 and a Reynolds number (Re) of 5.0 x 10⁵, based on the root …

Nebulizer-Based Systems To Improve Pharmaceutical Aerosol Delivery To The Lungs, Benjamin M. Spence

Theses and Dissertations

Combining vibrating mesh nebulizers with additional new technologies leads to substantial improvements in pharmaceutical aerosol delivery to the lungs across therapeutic administration methods. In this dissertation, streamlined components, aerosol administration synchronization, and/or Excipient Enhanced Growth (EEG) technologies were utilized to develop and test several novel devices and aerosol delivery systems. The first focus of this work was to improve the poor delivery efficiency, e.g., 3.6% of nominal dose (Dugernier et al. 2017), of aerosolized medication administration to adult human subjects concurrent with high flow nasal cannula (HFNC) therapy, a form of continuous-flow non-invasive ventilation (NIV). The developed Low-Volume Mixer-Heater (LVMH) …

The Effect Of Passive And Active Boundary-Layer Fences On Delta Wing Performance At Low Reynolds Number, Anna C. Demoret

Theses and Dissertations

The effect of passive and active boundary-layer fences (BLFs) on performance is evaluated on a NACA 0012 delta wing (c_root = 14in, c_tip = 2.8in, Λ = 45°, b = 23.5in) at a Reynolds number (Re) of 5.0 x 10⁵ based on the root chord. The performance improvements of a passive BLF are replicated and improved upon using an active flow control (AFC) fluidic fence created by a wall-normal steady-blowing jet from a slot. The application of a passive BLF at a spanwise location of 70% z/b resulted in an 8.7% increase in C_Lmax compared to …

Investigation Of Endwall Vortex Manipulation In High Lift Turbines Caused By Active Endwall Forcing, Horatio J. Babcock

Theses and Dissertations

With the increased demand for lighter, more fuel efficient and smaller gas turbine engines, the impetus to reduce the weight and size of the turbine has become apparent. One approach to reduce this weight is to reduce the number of blades in the turbine. However, to maintain power output, each blade must be capable of supporting a greater amount of lift. While several high-lift turbine profiles have been detailed in literature, most of these profiles have increased endwall losses, despite their desirable mid-span characteristics. To mitigate this endwall loss, a number of active and passive flow approaches have been studied …

Tracking Shock Movement On The Surface Of An Oscillating, Straked Semispan Delta Wing, Justin A. Pung

Theses and Dissertations

A recent research effort, sponsored by the Air Force Office of Scientific Research, numerically investigated the unsteady aerodynamic flow field around an oscillating, straked, delta wing. The study was centered on determining the importance of the unsteady aerodynamic forces acting as a driver for a nonlinear motion known as limit cycle oscillations. The current effort focused on creating a computational model to compare to the results of previous tests and modeling efforts and discover new information regarding the onset of LCO. The computational model was constructed using the Cartesian overset capabilities of the CREATE-AV™ fixed wing fluid dynamics solver Kestrel. …

Influence Of Leading Edge Oscillatory Blowing On Time-Accurate Dynamic Store Separation, Ryan G. Saunders

Theses and Dissertations

The primary objective of this research is to support the static and dynamic characterization and the time-accurate dynamic load data acquisition of store separation from a cavity with leading edge oscillatory blowing. Developing an understanding of, and potentially controlling, pitch bifurcation of a store release is a motivation for this research. The apparatus and data acquisition system was used in a two-part experiment to collect both static and dynamic testing data in the AFIT low speed wind tunnel in speeds of 60, 100, and 120 mph, from Reynolds numbers varying from 5.5x10⁴ to 4.6x10⁵, depending on reference …

Analytical Models And Control Design Approaches For A 6 Dof Motion Test Apparatus, Kyra L. Schmidt

Theses and Dissertations

Wind tunnels play an indispensable role in the process of aircraft design, providing a test bed to produce valuable, accurate data that can be extrapolated to actual flight conditions. Historically, time-averaged data has made up the bulk of wind tunnel research, but modern flight design necessitates the use of dynamic wind tunnel testing to provide time-accurate data for high frequency motion. This research explores the use of a 6 degree of freedom (DOF) motion test apparatus (MTA) in the form of a robotic arm to allow models inside a subsonic wind tunnel to track prescribed trajectories to obtain time-accurate force …

Wall Model Large Eddy Simulation Of A Diffusing Serpentine Inlet Duct, Ryan J. Thompson

Theses and Dissertations

The modeling focus on serpentine inlet ducts (S-duct), as with any inlet, is to quantify the total pressure recovery and ow distortion after the inlet, which directly impacts the performance of a turbine engine fed by the inlet. Accurate prediction of S-duct ow has yet to be achieved amongst the computational fluid dynamics (CFD) community to improve the reliance on modeling reducing costly testing. While direct numerical simulation of the turbulent ow in an S-duct is too cost prohibitive due to grid scaling with Reynolds number, wall-modeled large eddy simulation (WM-LES) serves as a tractable alternative. US3D, a hypersonic research …

Initial Stage Of Fluid-Structure Interaction Of A Celestial Icosahedron Shaped Vacuum Lighter Than Air Vehicle, Dustin P. Graves

Theses and Dissertations

The analysis of a celestial icosahedron geometry is considered as a potential design for a Vacuum Lighter than Air Vehicle (VLTAV). The goal of the analysis is ultimately to understand the initial fluid-structure interaction of the VLTAV and the surrounding airflow. Up to this point, previous research analyzed the celestial icosahedron VLTAV in relation to withstanding a symmetric sea-level pressure applied to the membrane of the structure. This scenario simulates an internal vacuum being applied in the worst-case atmospheric environmental condition. The next step in analysis is to determine the aerodynamic effects of the geometry. The experimental setup for obtaining …

Thermochemical Non-Equilibrium Models For Weakly Ionized Hypersonic Flows With Application To Slender-Body Wakes, Matthew P. Clarey

Theses and Dissertations

The current resurgence of interest in hypersonic technologies has warranted an inquiry into the commonly employed thermochemical non-equilibrium models within computational fluid dynamic (CFD) simulations. Additionally, research has historically focused on forebody flowfields, while studies of the complex wake structure have remained elusive. Although the forebody is of significance for vehicle analysis, the wake presents many exploitative characteristics. This dissertation aimed to address these two deficits. First, two three-temperature non-equilibrium models were developed, increasing the fidelity of hypersonic solutions above that of the legacy two-temperature model. The models were then investigated via zero-dimensional simulations, to detail the non-equilibrium processes, and …

Wall-Modeled Large Eddy Simulation Of A Three-Dimensional Shock-Boundary Layer Interaction, Nicholas J. Marco

Theses and Dissertations

The direct simulation of turbulent flows is prohibitive at high Reynolds numbers; thus, methods such as RANS and LES are used. However, these methods still require a large number of cells near a solid boundary. To circumvent this issue, a Wall-Modeled Large Eddy Simulation (WM-LES) can be used. Of interest is how these wall models perform in comparison to a Wall-Resolved Large Eddy Simulation (WR-LES) and experimental results of a shock turbulent boundary layer interactions (STBLI) and specifically, whether equilibrium wall models are sufficient to resolve the oscillatory and hence non-equilibrium nature of these flows or whether a non-equilibrium model …

An Efficient Euler Method To Predict Shock Migration On A Straked Delta Wing Design, Dylan N. Hope

Theses and Dissertations

In support of the Air Force Office of Scientific Research, this project sought to identify the significance of nonlinear aerodynamic phenomena in regards to LCO of a straked delta wing design. Previous works include unsteady Navier-Stokes aeroelastic analysis of various wing designs and flight test of F-16 transonic LCO with interest focused on oscillatory SITES behavior. The research presented within this investigation further expanded the understanding of unsteady aerodynamics by performing aeroelastic analysis of a wing oscillated in pitch with an Euler-based, boundary layer coupled numerical method (ZEUS). The wing was tested for a multitude of LCO parameters such as …

Investigation Of Dynamic Store Separation Out Of A Weapons Bay Cavity Utilizing A Low Speed Wind Tunnel, Andrew D. Bower

Theses and Dissertations

Characterizing mission store trajectories as they separate from a weapons bay cavity is highly relevant to the Air Force mission. The flow around a weapons bay is unsteady. The unsteady flow can cause a mission store separation trajectory to be unpredictable, and such is the case for what some have termed a pitch bifurcation. Traditional wind tunnel testing is incapable of detecting a bifurcation because traditional wind tunnel testing records time-averaged data. In this study, an experimental testing system was developed and refined in order to support the time-accurate characterization of dynamic mission store separation events. A Motion Test Apparatus …

Time-Dependent Validation Of Finite Element Strain Distribution Of A Plastically-Deformed Plate Via Digital Image Correlation, Kevin R. Knapp

Theses and Dissertations

Generation of residual stress is an essential step in the generation of Goodman data via Air Force Research Laboratory's vibration-based fatigue test. Conventional Goodman data is constructed through uniaxial fatigue testing at a rate of 40 Hz, while the vibration-based testing excites stresses at 1,600 Hz in a stress state that is similar to those seen in gas turbine engine airfoils. A pre-strain procedure is conducted to form residual tensile stress, which serves as a steady stress when the specimen is subjected to fully-reversed vibration-based fatigue loads. This steady tensile stress is desired at the fatigue zone of the test …

Cavity Geometric Features And Entrainment Characterization Resulting From A Ballistically Induced Hydrodynamic Ram Event, Andrew J. Lingenfelter

Theses and Dissertations

Hydrodynamic Ram can cause damage to industrial and aircraft systems. The resulting transient spray increases the probability of fire. To better understand the driving mechanisms behind transient spray, internal, and external measurements of the cavity geometry, and entrained flow field were accomplished. Research determined cavity contraction and separation are pre-cursors to the initiation of the transient spray phases. The entrained flow measurement required development of a new and novel technique using a continuous wave laser and atomized water particles. The peak mass flow correlated well with cavity geometric features, such as cavity contraction. Using the mass flow, cavity diameter at …

Force And Moment Measurements Applicable To A Flexible Weapons System, James B. Sellers

Theses and Dissertations

Continuing the development of the 6-DOF Motion Test Apparatus (MTA) for performing dynamic wind tunnel tests revealed the importance of a capable data acquisition (DAQ) system for collecting and analyzing data. Assembling and testing the DAQ system in conjunction with the MTA, AFIT Low-Speed Wind Tunnel, and a selection of high-performance sensors was the primary focus of this research. Specifically, acquiring time-accurate aerodynamic force and moment measurements on a variety of test models was of high importance. With the established real-time DAQ system hardware, a National Instruments (NI) LabVIEW program was created to acquire data from an ATI Nano25-E force …