Aerodynamics and Fluid Mechanics Commons^™

Analysis Of Wingtip Vortex Structure Generated By Bio-Inspired Winglets, D'Zahn A. Smith

Doctoral Dissertations and Master's Theses

Bio-inspired winglets were studied with the goal of better understanding the structure of the wingtip vortices they generate. Measurements of the tip vortex were previously carried out using stereoscopic particle image velocimetry (sPIV). The bio-inspired winglet was tested on a rectangular NACA 0012 wing section at a 5-degree angle of attack and at a chord Reynolds number of 900,000. Velocity field measurements were recorded at 0.7 and 2 chord lengths aft of the wing’s trailing edge. Compared to the wing with no attachment and a traditional blended winglet, the bio-inspired winglet’s vortex exhibited significantly less intense flow field properties. These …

Characterization And Analysis Of Supersonic Flow Through De Laval Nozzles At Varied Design Conditions, Sarah Baird

Doctoral Dissertations and Master's Theses

A combined numerical and experimental investigation of supersonic planar nozzles under different design conditions has been conducted. Supersonic planar nozzles are common geometries observed in supersonic wind tunnels and aircraft or rocket engines. For the important role they play in wind tunnel testing and aircraft propulsion, it is important to conduct a thorough numerical and experimental study to characterize their performance at different operating conditions. In this study, a de Laval nozzle was scanned to extract its contours and subsequently modeled to compare analytical and numerical performance expectations under design and off-design conditions. The nozzle was then installed in a …

Modeling Of Rotor Wake Vortex Dynamics And Interactions In Non-Homogenous Vertiport Environments, Garrison P. Shaw

Doctoral Dissertations and Master's Theses

The current research serves to analyze and study the effects ground forces can have on the thrust performance of a propeller in multiple different configurations. The current research utilizes an open source Computational Fluid Dynamics (CFD) software known as OpenFOAM to generate calculate and visualize these runs. The model used for this experiment is a hybrid model that employs both a Unsteady Reynolds-Averaged Navier-Stokes (URANS) and a detached eddy simulation using a hybrid Large Eddy Simulation (LES) via a KomegaSSTDDES model. This model serves to save computational time as well as allow for accurate results. The three cases run are …

Development Of Eagle3d Solver For Wall Modeled Les Of Transonic Flows, Spencer Moore

Doctoral Dissertations and Master's Theses

Wall modeled Large Eddy Simulation (LES) is an area of interest due to its ability to lower computational costs of LES simulation. Even with the application of wall models, LES still proves to have practicality issues when it comes to use in industry, due to the expertise, time, and computational resources required to get results. A case described by an axisymmetric transonic bump is explored utilizing the Embry-Riddle Aeronautical Universities in house unstructured finite volume multi-element CFD code, Eagle3D. Eagle3D, has been brought to the state of the art and validated against current research using this transonic bump case as …

Conceptual Design Methodology For The Fan-In-Wing Vtol Aircraft, Brock Steinfeldt

Doctoral Dissertations and Master's Theses

The Fan-In-Wing (FIW) aircraft concept is one of the most compelling solutions for missions demanding jet-like cruise speeds and Vertical TakeOff and Landing (VTOL) capability. However, despite years of interest and documented improvements in lift-fan technology, there exists little in the way of an adequate theory for conceptual design of a fan-in-wing aircraft. To address this issue, a general conceptual design methodology has been developed as a source of guidance for the FIW designer. Through this work, the top-level requirements ranking the fan-in-wing concept above other VTOL aircraft have been defined, while a cross-comparison between the FIW concept and conventional …

Development Of On-The-Fly Quasi-Steady State Approximation For Chemical Kinetics In Cfd, Abhinav Balamurugan

Doctoral Dissertations and Master's Theses

This study analyzes the feasibility of On-The-Fly Quasi-Steady-State Approximation (OTF-QSSA) application for solving chemical kinetics within Computational Fluid Dynamics (CFD) simulations, aiming to reduce the computational demand of detailed mechanisms. An algorithm that dynamically identifies and designates Quasi-Steady-State (QSS) species at specific grid locations and instances during the simulation was developed. With this information, our method pseudo-delays the advancement of concentrations for these QSS species—effectively setting their rate of concentration change to zero for a set number iteration before updating using the detailed mechanism and thereby omitting the computationally intensive processes typically required for their calculation during those skipped iteration. …

Numerical Study In Wind Energy Extraction From Controlled Limit-Cycle Oscillations In Modified Glauert Airfoil, Ethan L. Deweese

Doctoral Dissertations and Master's Theses

Typically, wind energy harvesting technology employs wind turbines. Towards the goal of meeting increasing energy needs with renewable energy sources a novel wind energy harvesting scheme is considered, utilizing a modified Glauert (MG) airfoil experiencing aeroelastic limit cycle oscillation (LCO) from which energy may be extracted. Synthetic jet actuators (SJA)s are used along with the unique geometry of the MG airfoil to control flow separation and amplify the LCO and energy generation potential of the system. The discussed wind energy harvesting scheme could provide flexibility in allowing installations previously unsuitable to wind turbines due to geometric or low wind velocity …

Mitigating Engine Unstart In Scramjets With Porous Bleeders, Ryan Lindley

Doctoral Dissertations and Master's Theses

The effectiveness of porous bleeders in mitigating unstart phenomena and enhancing isolator effectiveness in a hypersonic scramjet was investigated. Through computational fluid dynamics simulations, the impact of porous bleeder design parameters such as pressure jump coefficient and bleeder size on isolator effectiveness and unstart prevention was evaluated. Results indicated that porous bleeders delayed flow separation and reduced adverse pressure gradients, thereby enhancing isolator performance. Additionally, porous bleeders demonstrated promising capabilities in preventing full unstart events and mitigating oscillatory unstart phenomena.

Adaptive Control Of An Aeroelastic System For Active Flutter Suppression And Disturbance Rejection, Patrick Sterling Downs

Doctoral Dissertations and Master's Theses

The future of aircraft design strives for lighter weight, more aerodynamically efficient structures. These improvements may come with the drawback of increased structural flexibility and elevated aeroelastic effects, often resulting in a lower flutter speed. This motivates the implementation of advanced control methods to control aeroelastic systems over a range of flight conditions, suppress and delay the onset of flutter, and compensate for disturbances, actuator dynamics, and unmodeled nonlinear dynamics.

This dissertation first develops a novel method for constructing time-domain simulation models of two and three-dimensional aeroelastic systems, resulting in models that are suitable for the implementation of state-space control …

The Influence Of Mixing Duct Length And Phase Of Flight On Wall Temperatures Of A Rocket Based Combined Cycle Engine In Ejector And Air-Augmented Modes, Jonathan Grow

Doctoral Dissertations and Master's Theses

Rocket Based Combined Cycle (RBCC) engines have been theorized as a possible means of powering launch vehicles and high-speed atmospheric vehicles. By incorporating aspects of both air-breathing and rocket propulsion, RBCC engines promise up to a 230 % increase in specific impulse over traditional chemical rocket propulsion by entraining a secondary flow of atmospheric air and mixing it with the exhaust of a rocket motor. Students within the Embry-Riddle Future Space Explorers and Developers Society (ERFSEDS) identified a
problem of excessive heating and structural failure of the mixing duct during launch and transonic flight of a student-built flight test vehicle. …

A Simulation Of The Impacts Of Climate Change On Civil Aircraft Takeoff Performance, Thomas D. Pellegrin

Doctoral Dissertations and Master's Theses

Climate change affects the near-surface environmental conditions that prevail at airports worldwide. Among these, air density and headwind speed are major determinants of takeoff performance, and their sensitivity to global warming carries potential operational and economic implications for the commercial air transport industry. Previous archival and prospective research observed a weakening in headwind strength and predicted an increase in near-surface temperatures, respectively, resulting in an increase in takeoff distances and weight restrictions. The main purpose of the present study was to update and generalize the extant prospective research using a more representative sample of worldwide airports, a wider range of …

Understanding The Structure Of Wing Tip Vortices Of Bio-Inspired Winglets, Greeshma C. Daniel

Doctoral Dissertations and Master's Theses

Bio-inspired wing tip devices were investigated with the goal of improving the fuel efficiency of subsonic aircraft. Particularly, the structure of a bio-inspired winglet design based on bird feathers were tested in a low-speed wind tunnel. Particle image velocimetry (PIV), was used to study the flow field at two planes aft of the wing as the wing tip vortices developed downstream. These were time-dependent, stereoscopic particle image velocimetry (sPIV) measurements carried out at two planes located at 0.7 and 2 chord distances downstream from the wing. The structure of the wingtip vortices was compared and contrasted with that formed over …

Prediction & Active Control Of Multi-Rotor Noise, Samuel O. Afari

Doctoral Dissertations and Master's Theses

Significant developments have been made in designing and implementation of Advanced Air Mobility Vehicles (AAMV). However, wider applications in urban areas require addressing several challenges, such as safety and quietness. These vehicles differ from conventional helicopter in that they operate at a relatively lower Reynolds number. More chiefly, they operate with multiples of rotors, which may pose some issues aerodynamically, as well as acoustically. The aim of this research is to first investigate the various noise sources in multi-rotor systems. High-fidelity simulations of two in-line counter-rotating propellers in hover, and in forward flight conditions are performed. Near field flow and …

Numerical Modeling Of Synthetic Vortical Disturbance Interactions Using Openfoam, Ahmed Bilal

Doctoral Dissertations and Master's Theses

Nowadays, the number of Advance Air Mobility (AAM) Electic Vertical Take-off and Landing (eVTOL) concepts is rapidly increasing due to their capability of vertical take-off and landing at vertiports located on rooftops of tall urban buildings, which does not require using the ground space in a condensed urban environment. Such flight operations, however, will be greatly affected by the vertiport’s highly unsteady, turbulent flow environment. The goal of this study is to model the turbulent wind interaction with a building to understand the unsteady flow characteristics around vertiports and match the induced unsteady disturbance field to the canonical disturbance forms, …

The Linearized Euler Equations For Predicting Supersonic Jet Noise Of A Rectangular Jet Using Openfoam, Patrick Good

Doctoral Dissertations and Master's Theses

This thesis presents a Linearized Euler Equation (LEE) solver that was developed for OpenFOAM. OpenFOAM is an open-source Computational Fluid Dynamics (CFD) package that is widely used by industry and academia. The LEE’s are a set of equations used in Computational Aeroacoustics (CAA). The LEE’s can solve for the acoustic solution directly and quickly. The solver developed, named leeFoam, was tested against analytical solutions to verify accuracy and then was utilized to predict the acoustics of a heated supersonic rectangular jet. The rectangular jet (RJET) results were compared against experimental data.

The results from this work show that OpenFOAM can …

Noise And Propulsive Efficiency Interactions For Rotors And Propellers At Constant Thrust, Riccardo Roiati

Doctoral Dissertations and Master's Theses

In the emerging market of Advanced Air Mobility (AAM), aerospace companies have been designing and prototyping electric and hybrid vehicles to revolutionize travel. These vehicles must have low noise and particulate emissions while also having enough propulsive efficiency to complete the mission. This thesis aims to study the relationship between noise and propulsive efficiency as related to any aircraft equipped with an electric motor and a variable pitch rotor/propeller. The combination of the electric motor with the variable pitch propeller/rotor allows for a decoupled rotational speed and torque generation, meaning that the electric motor can generate the same amount of …

Development And Deployment Of A Dynamic Soaring Capable Uav Using Reinforcement Learning, Jacob Adamski

Doctoral Dissertations and Master's Theses

Dynamic soaring (DS) is a bio-inspired flight maneuver in which energy can be gained by flying through regions of vertical wind gradient such as the wind shear layer. With reinforcement learning (RL), a fixed wing unmanned aerial vehicle (UAV) can be trained to perform DS maneuvers optimally for a variety of wind shear conditions. To accomplish this task, a 6-degreesof- freedom (6DoF) flight simulation environment in MATLAB and Simulink has been developed which is based upon an off-the-shelf unmanned aerobatic glider. A combination of high-fidelity Reynolds-Averaged Navier-Stokes (RANS) computational fluid dynamics (CFD) in ANSYS Fluent and low-fidelity vortex lattice (VLM) …

Artificial Neural Network For Predicting Heat Transfer Rates In Supercritical Carbon Dioxide, Vinusha Dasarla Giri Babu

Doctoral Dissertations and Master's Theses

Supercritical carbon dioxide as a working fluid in a closed Brayton cycle is proving to be more efficient than a conventional steam-based Rankine engine. Understanding the heat transfer properties of supercritical fluids is important for the design of a working engine cycle. The thermophysical properties of supercritical fluids tend to vary non-linearly near the pseudo-critical region. Traditionally, empirical correlations are used to calculate the heat transfer coefficient. It has been shown in the literature and within our own studies that these correlations provide inaccurate predictions near the pseudo-critical line, where heat transfer may be deteriorated or enhanced, resulting from strong …

A Study Of Ship Airwakes Using Dual Plane Stereoscopic Piv, Guillermo Mazzilli

Doctoral Dissertations and Master's Theses

The airwake of a model Simple Frigate Shape 2 (SFS2) was studied in a low-speed wind tunnel. This airwake was measured using a novel time-dependent, dual plane, stereoscopic particle image velocimetry approach. Two flow planes over the flight deck, one parallel and one perpendicular to the free-stream were simultaneously measured. Measurements were carried out over four such pairs of streamwise-spanwise plane combinations. Additionally, the airwake with and without a simulated atmospheric boundary layer (sABL) was studied. The synchronicity of the measurements were taken advantage of to carry out conditional averages of the flow field to isolate and study certain flow …

Understanding Unsteady Corner Separation Within Wing-Body Junction Flows, Paul G. Winner

Doctoral Dissertations and Master's Theses

Wing-body junction flows, formed at the interface between a wing and fuselage surface, are a complex, coupled, three-dimensional, turbulent flow field. This thesis focused on the unsteady corner separation that develops at the trailing edge of this wing-body junction under certain conditions. A NACA 0015 wing mounted on a flat plate at an angle of attack of 13°was used as the model junction flow field. The wing had an aspect ratio of 8 with a linear washout twist of 15°. The Reynolds number based on the wing chord was Re_c = 4.5 × 10⁵. Time-dependent stereoscopic particle …

A Data Driven Modeling Approach For Store Distributed Load And Trajectory Prediction, Nicholas Peters

Doctoral Dissertations and Master's Theses

The task of achieving successful store separation from aircraft and spacecraft has historically been and continues to be, a critical issue for the aerospace industry. Whether it be from store-on-store wake interactions, store-parent body interactions or free stream turbulence, a failed case of store separation poses a serious risk to aircraft operators. Cases of failed store separation do not simply imply missing an intended target, but also bring the risk of collision with, and destruction of, the parent body vehicle. Given this risk, numerous well-tested procedures have been developed to help analyze store separation within the safe confines of wind …

Experimental Characterization Of Additively Manufactured Multi-Feather Wingtip Devices, Patricio Garzon

Doctoral Dissertations and Master's Theses

Soaring birds have evolved to fly for long periods of time without flapping their wings. Inspired by the flight of these birds, the proposed thesis presents an experimental investigation focused on wingtip devices designed based on biomimicry. The overarching engineering objective was to reduce the induced drag as a means to improve the fuel efficiency via these experimental wingtips. An associated secondary objective was to establish a method for manufacturing complex structures suitable for wing tunnel testing. A manufacturing technique that involved using composite weaves to reinforce additively manufactured structures was developed. This technique has the potential to reduce manufacturing …

Effect Of Spray Rails On Takeoff Performance Of Amphibian Aircraft, Soham Bahulekar

Doctoral Dissertations and Master's Theses

Amphibian aircraft have seen a rise in popularity in the recreational and utility sectors due to their ability to take off and land on both land and water, thus serving a myriad of purposes such as aerobatics, surveillance, and firefighting. The design of such seaplanes requires to be both aerodynamically and hydrodynamically efficient, especially during the takeoff phase. In the past, naval architects have implemented ways to make boats, yachts, and large ships more efficient; one of them being the addition of chine strips and spray rails on the hull. This thesis study explores the possibility of implementing spray rails …

Time-Resolved Piv Measurements Of Ship Airwakes With Quartering Winds, Kaijus H. Palm

Doctoral Dissertations and Master's Theses

The unsteady, three-dimensional, turbulent airwake over the Simple Frigate Ship No. 2 (SFS2) with quartering wind flow directions was studied in a low-speed wind tunnel facility. Surface oil flow visualization and time-resolved stereoscopic and planar particle image velocimetry (PIV) measurements were made for three crosswise planes and a single centerline streamwise plane. Measurements included various configurations with the bow of the ship model at two different quartering wind conditions of 10 and 20 degrees, as well as cases with and without the effects of a simulated atmospheric boundary layer (ABL). A comparative analysis of the time-averaged flow structures between the …

Influence Of Wing Planform Shape On The Effectiveness Of A Fixed-Slot, Yuan Zhao

Doctoral Dissertations and Master's Theses

This thesis report explores the effect of the Clark-Y wing geometry on lift and drag to use as a reference during aircraft design stage. The different characteristics investigated are fixed slot span, taper ratio, washout, and sweep angle. Plain wings, half slotted wings, and fully slotted wings were built in CATIA with an aspect ratio of 6 and different taper ratio, washout, and sweep angles. Using the CATIA models to generate the 3-D grids in Pointwise. All the simulations were tested in Ansys-Fluent under sea-level conditions with a Reynold number of 609000. The relationships between the aerodynamic characteristics and the …

Numerical Simulation Of A Cryogenic Spray, Neel Kishorkumar Shah

Doctoral Dissertations and Master's Theses

Cryogenic sprays have many applications in modern engineering. Cooling of electronic equipment subject to high heat flows, surgical ablation of gastrointestinal mucosae or orbital maneuvering are a few examples of their versatility. However, the atomization of a cryogenic liquid is a complex process. During such an event, aerodynamic effects associated with secondary atomization are further affected by thermodynamic flashing. A better understanding of the characteristics of cryogenic sprays is then necessary to allow for improved design and optimization in applications. The overarching objective of this study is to document such characteristics. The numerical simulation was performed over cryogenic nitrogen spray …

Background Flow Influence On Impulsive Jet-Driven Micro Droplet Dispersal, Vaishak Thiruvenkitam

Doctoral Dissertations and Master's Theses

Accurately predicting the airborne spread of infectious diseases is crucial in controlling the COVID­19 pandemic today. Studies have shown the spread of expiratory droplets depends on ambient thermodynamic conditions and flow properties of the jet emitted by the activity. However, the droplet spread in conditions of background flow is not yet comprehensively understood. This study uses the Eulerian­-Lagrangian model with k−ω turbulence modelling to simulate spread of particles and study the factors affecting it in a closed environment with a background flow. Respiratory activities are modeled as a non-­isothermal jet of air with droplets suspended in them in a predetermined …

Active Control Of Coherent Structures In An Axisymmetric Jet, Michael Marques Goncalves

Doctoral Dissertations and Master's Theses

The primary objective of this work is to develop high-fidelity simulation model for jet noise control predictions and quantify the sound reduction when an external source frequency mode excitation is imposed on the jet flow. Whereas passive approaches using mixing devices, such as chevrons, have been shown to reduce low-frequency noise in jet engines, such approaches incur a performance penalty since they result in a reduced thrust. To avoid a performance penalty in reducing jet noise, the current work investigates a open-loop active noise control (ANC) system that utilizes a unsteady microjet actuator on the nozzle lip in the downstream …

Design And Flight-Path Simulation Of A Dynamic-Soaring Uav, Gladston Joseph

Doctoral Dissertations and Master's Theses

We address the development of a dynamic-soaring capable unmanned aerial vehicle (UAV) optimized for long-duration flight with no on-board power consumption. The UAV’s aerodynamic properties are captured with the integration of variable fidelity aerodynamic analyses. In addition to this, a 6 degree-of-freedom flight simulation environment is designed to include the effects of atmospheric wind conditions. A simple flight control system aids in the development of the dynamic soaring maneuver. A modular design paradigm is adopted for the aircraft dynamics model, which makes it conducive to use the same environment to simulate other aircraft models. Multiple wind-shear models are synthesized to …

On The Local Heat Transfer Behavior Of Supercritical Carbon Dioxide, Neil Sullivan

Doctoral Dissertations and Master's Theses

A detailed study of the local heat transfer behavior of supercritical carbon dioxide (sCO2) is performed. Flows relevant to heat transfer devices, such as sCO2 heaters, recuperators, and internally cooled turbine blades are studied, with particular attention paid to data reduction methodology, and the use of appropriate reference quantities, nondimensionalizations, and correlations. Additionally, a semi-intrusive temperature measurement technique capable of obtaining highly spatially resolved temperature distributions is adapted for use in the challenging conditions of supercritical (SC) flow. SC fluids have proven difficult to study both experimentally and numerically due to dramatically changing thermodynamic and transport properties near the critical …