Aerodynamics and Fluid Mechanics Commons^™

Effect Of Slot Span On Wing Performance, Juan F. Granizo

Doctoral Dissertations and Master's Theses

This report presents new numerically-derived correlations to estimate the aerodynamic properties of a three-dimensional wing that features a partial to full span fixed slot. Fixed slots have been thoroughly studied in the past with regards to their operation and the relation between slot geometry and wing performance. There have also been many studies on the advantages and disadvantages of tip-slotted wings and the comparison between these and full-slotted wings. Up to this point however, a study on the effects of slot span on wing performance has not been performed. Effect of slot span on wing performance is evaluated in an …

Effect Of Flow-Acoustic Resonant Interactions On Aerodynamic Response Of Transitional Airfoils, Joseph Hayden

Doctoral Dissertations and Master's Theses

A high-accuracy numerical study is conducted to examine the impact of flow-acoustic resonant interactions on the aerodynamic response of symmetric and cambered airfoils in the realistic transitional flow regimes with Rec=140,000 and M=0.0465 as well as the low Reynolds number flow regime with Rec=10,000 and M=0.2. The symmetric NACA-0012 and the cambered SD7003 airfoils are investigated at various angles of attack that have been found previously to include both the tone and no-tone producing regimes, with specific focus on the aerodynamic lift response. Additional simulations are conducted with a low-intensity synthetic turbulence introduced upstream of the airfoils in order to …

A Computer Program For The Coupled Implementation Of Meanline And Throughflow Methods To Simplify The Aerodynamic Design Of Multistage Axial Compressors, Alexander V. Rozendaal

Doctoral Dissertations and Master's Theses

A computer program capable of simplifying the preliminary aerodynamic design process of multistage axial compressors has been developed. This interactive design tool, named C-STAAC, combines the Meanline and Throughflow analysis capabilities of two independent compressor design codes to form one standalone system. The program greatly improves the efficiency of the Preliminary-to-Throughflow stages of compressor design by providing fully coupled interaction between the two platforms. The result enables the user to produce stacked airfoil geometry from only a handful of initial input parameters.

The program additionally offers a wide selection of pre- and post-processing capabilities that were not previously available with …

Heat Transfer Analysis Of An Oblique Jet Impingement Cooling On Cmc Rough Surface, Karthik Krishna

Doctoral Dissertations and Master's Theses

A Ceramic Matrix Composite is high strength and high temperature capability composite, utilized in components like heat shield of space vehicles, flame holders and disc brakes. To be used in both static and dynamic components of a future gas turbine engine and even with high temperature capabilities of these CMC components, convection cooling will still likely be required. The surface of the CMC varies significantly from traditional super-alloy used in a modern engine, with large level of roughness and significant three-dimensional waviness. These complex features will impact the behavior of the near wall flows, and affect the heat transfer rates …

Computational Investigation Of Impingement Cooling For Regeneratively Cooled Rocket Nozzles, Bianca A. De Angelo

Doctoral Dissertations and Master's Theses

Jet impingement cooling is an internal cooling configuration used in the thermal management of temperature sensitive systems. With rocket engine combustion temperatures rising as high as 3600 K, it is essential for a cooling method to be applied to ensure that the nozzle integrity can be maintained. Therefore, a novel heat transfer study is conducted to investigate if jet impingement cooling is feasible for a regenerative cooling rocket nozzle application. Regenerative cooling for liquid propellant rockets has been widely studied. However, to the best of the author’s knowledge, there is currently no literature describing this method in conjunction with impingement …

Fluidic Jet Turbulence Generators For Deflagration To Detonation Transition In Pulsed Detonation Combustors, Jarrett E. Lowe

Doctoral Dissertations and Master's Theses

The goal of this study is to establish the dominant flow structure required to effectively accelerate the turbulent deflagration flame front to detonation velocity in the shortest possible distance while using a single Jet in Cross Flow (JICF). Jets in crossflow, depending on orientation and momentum ratio, can induce two types of flow structures that propagate downstream; vortex filaments and turbulent eddies. Vortex flow structures are coherent rotating columns that can persist for a considerable distance before diffusing. Turbulent eddies are characterized as random fluctuations in flow velocity or small pockets of rotation. The test rig used for this study …

Study Of Hybrid Magneto-Active Propellant Management Device For Slosh Damping, Leander Paul

Doctoral Dissertations and Master's Theses

Sloshing of liquid upon the application of an external force is a natural phenomenon as the free surface is allowed to move without any constraints. Study of slosh is an ongoing research for many decades and many novel inventions in Propellant Management Devices (PMDs) such as the rigid baffles and elastomeric membranes have been implemented to counteract the free surface effect in both passive and active membrane known as Magneto-Active Propellant Management Device (MAPMD) to actively control the free surface effect and reduce fuel slosh is explored in this research. Being a hybrid membrane, it would initially offer passive resistance …

2d Aeroacoustic Analysis Of Flow In The Flame Trench, Meghan Pokorski

Doctoral Dissertations and Master's Theses

We present here a methodology for using the commercial software ANSYSFLUENT to predict the acoustic field associated with Space-Launch System (SLS). We consider a two-dimensional model of flame deflector, and flame trench. The ANSYS code is then used to simulate the internal flow. Both the steady state case is considered along with other cases where the inflow has a harmonic component. A Ffowcs-Williams Hawking (FWH) surface is then constructed within the computational domain to use the computed flow fluctuations to obtain the acoustic field. The acoustic data was then compared to the experimental data.

When using the ANSYS code for …

Aerodynamic Trade Study Of Compound Helicopter Concepts, Julian Roche

Doctoral Dissertations and Master's Theses

The relative performance attributes of compound helicopter concepts have been examined, including their potential for meeting the requirements of several challenging mission profiles. For each concept, which included lift and/or propulsive compounding, a suite of aerodynamic performance models was developed using energy methods. In the case of a lift-compounded concept, an aerodynamic model representing the force interaction effects of the main rotor wake with the wing was also developed. Models of a conventional helicopter and of a tiltrotor were implemented as well, and the results used as a datum for comparison. In each case, the predictive capabilities of the model …

Direct Adaptive Control For Stability And Command Augmentation System Of An Air-Breathing Hypersonic Vehicle, Ron Aditya

Doctoral Dissertations and Master's Theses

In this paper we explore a Direct Adaptive Control scheme for stabilizing a non-linear, physics based model of the longitudinal dynamics for an air breathing hypersonic vehicle. The model, derived from first principles, captures the complex interactions between the propulsion system, aerodynamics, and structural dynamics. The linearized aircraft dynamics show unstable and non-minimum phase behavior. It also shows a strong short period coupling with the fuselage-bending mode. The value added by direct adaptive control and the theoretical requirements for stable convergent operation is displayed. One of the main benefits of the Directive Adaptive Control is that it can be implemented …

Numerical Study Of Synthetic-Jet Actuation Effect On Airfoil Trailing Edge Noise, Marco Sansone

Doctoral Dissertations and Master's Theses

The current study conducts numerical simulations to assess the possibility of employing Synthetic Jet Actuators (SJAs) as active noise control devices for reduction of airfoil acoustic radiation. High-accuracy numerical efforts employ a sixth-order accurate Navier-Strokes solver implementing a low-pass filtering of poorly resolved high-frequency solution content to retain numerical accuracy and stability over the range of transitional flow regimes. In the adopted numerical procedure, the actuator is modeled without its resonator cavity through imposing a simple fluctuating-velocity boundary condition at the bottom orifice of the actuator. The orifice cavity with the properly defined boundary condition is embedded into the airfoil …

Similarity Analysis Of A Swirling Counter-Flow, Jitesh Rane

Doctoral Dissertations and Master's Theses

Swirling counter-flows are used in numerous engineering applications, like combustion, heat exchangers, cyclonic separation and mixing, etc. These swirling counter-flows produce complex flow fields. It is important to study these types of flows in order to use them properly in many applications.

The present work provides insight into the flowfield inside a swirling counter-flow when the fluid is injected tangentially in a cylindrical container. A semi-analytical solution is developed by starting with the full Navier-Stokes equation and using a similarity analysis. A decaying swirl along the axis of the cylinder is assumed, which reduces the Navier-Stokes equations to first order …

Surface Structure And Its Effect On Reducing Drag, Ragini Ramachandran

Doctoral Dissertations and Master's Theses

A miniature subsonic open return wind tunnel was designed and fabricated to measure drag on small test models at low Reynolds numbers. The wind tunnel featured a sensitive strain gauge type load cell. The average drag coefficient of sphere and cube test models were used to validate the miniature wind tunnel, and the values obtained were consistent with published results over the range of Reynolds numbers tested. These initial results gave confidence that the tunnel could be used to study the effects of surface finish on the drag of various models. Several fabrics with differing ribbed surface structures, including a …

Determination Of A Simplified High-Order Vortex Equation For Radial Equilibrium With Cfd Verification, Travis K. Matsumoto

Doctoral Dissertations and Master's Theses

The goal of this thesis is to determine a flow model that provides a better blade design over current design techniques utilizing a hybrid vortex model. This hybrid vortex model combines the well-established simple radial equilibrium vortex models into a higher order equation that will establish the basis for a more flow-accurate model. In this paper, we will discuss the basis and derivation of these vortex models, the shortcomings of current techniques, and verification of the new vortex model with empirical data via Computational Fluid Dynamic (CFD). The simple radial equilibrium equation set has been known to the scientific community …

Design And Dynamic Analysis Of A Variable-Sweep, Variable-Span Morphing Uav, Nirmit Prabhakar

Doctoral Dissertations and Master's Theses

Morphing wings have the potential to optimize UAV performance for a variety of flight conditions and maneuvers. The ability to vary both the wing sweep and span can enable maximum performance for a diverse range of flight regimes. For example, low-speed missions can be optimized using a wing with high aspect ratio and no wing sweep whereas high-speed missions are optimized with low aspect ratio wings and large wing sweep. Different static morphing wing configurations clearly result in varying aerodynamics and, as a result, varying dynamic modes. Another important consideration, however, is the transient dynamics that occur when transitioning between …

Exploration Of A Computational Fluid Dynamics Integrated Design Methodology For Potential Application To A Wind Turbine Blade, Gaurav Kapoor

Doctoral Dissertations and Master's Theses

The main purpose of this thesis is to conduct a parametric sensitivity study on the blade design of AOC 15/50 wind turbine based on a CFD approach and optimize the blade design for maximizing the power output. The ANSYS® Fluent® flow solver using the k-ω SST turbulence model was validated by simulating the flow over two dimensional airfoils comprising the AOC 15/50 wind turbine blade. The CFD results have shown a considerable agreement with the experimental data for the airfoils. Parametric correlation study and sensitivity analysis were conducted by performing actual flow simulations over the turbine blade using ANSYS® Fluent®. …

A Cfd Investigation Of The Hydrodynamic Characteristics Of Fluid Flow Through An Impeller And Multi-Objective Design Optimization Of A Centrifugal Pump, Mohammed Khammat Sagban

Doctoral Dissertations and Master's Theses

In this thesis, the first part is conducting an investigation of the hydrodynamic characteristics (pressure and velocity) of fluid flow (water) through an impeller of a centrifugal pump. To illustrate a one-dimensional model is used to identify an impeller of a GDM 10 x 12 HD centrifugal pump using Vista CPD design and BladeGen tool. A three-dimensional model is then built with a commercial software package ANSYS Blade Modeler. The structured mesh of the impeller blade is obtained by using TurboGrid system. The volute of the centrifugal pump is built in ANSYS geometry, and an unstructured mesh is accomplished by …

Unsteady Viscous Cavity Flow Using Computational Fluid Dynamics, Chandramouli Vadlamudi

Doctoral Dissertations and Master's Theses

The problem of unsteady viscous incompressible flow in a two-dimensional cavity is treated using the unsteady incompressible Navier-Stokes equations with various initial and boundary conditions. First the case of a square cavity with one inlet and one outlet is treated in steady and unsteady flows. The software package ANSYS FLUENT was used in the CFD simulations. This approach captures the appearance of separation bubbles and vortex formation inside the cavity. Steady state flows are also obtained from the unsteady simulations after convergence of the time dependent solutions. Then the case of a cavity with a synthetic jet and two outlets …

Separation Bubbles And Vortex Formation In Cavity Flows, Kartheek Ravulapati

Doctoral Dissertations and Master's Theses

This research is a computational fluid dynamic study of the formation of vortices and separation bubbles in a square cavity as well as in a cylindrical cavity. Whereas there has been previous research work on the problem of a free stream over different types of cavities, like open and closed cavities or lid driven cavities, this research on an inlet induced flow inside a square cavity lead to unusual and interesting basic fluid dynamical phenomena. The flow in a square cavity and in a cylindrical cavity is simulated over a range of Reynolds numbers and the appearance of separation bubbles …

Performance Improvement Through Velocity Triangle Optimization-Driven Redesign For Mitigating The Horseshoe Vortex In Axial Turbines, Vladislav Shulman

Doctoral Dissertations and Master's Theses

Momentum differences between the neighboring streamlines at the end wall/primary flow interaction region of an axial turbine stage induce three-dimensional vortical flow structures, such as the leading edge horseshoe vortex, resulting in significant aerodynamic performance deterioration. Reducing the effect of such flow instabilities requires turbine blade modification to discourage boundary layer roll-up, but traditional structural modification design systems can be prohibitively complex and time-intensive.

To address this problem, this study contributes a blade modification method involving airfoil shape optimization, designed to adjust the leading edge airfoil shape in horseshoe vortex-affected turbine applications. The key insight is that airfoil design (treated …

Flow Separation Control Using Synthetic Jets On A Flat Plate, Karunakaran Saambavi

Doctoral Dissertations and Master's Theses

The primary goal of this thesis is to assess the effect of synthetic jets on flow separation. CFD simulation is conducted for laminar flow over a flat plate using the commercial software ANSYS FLUENT. The oscillating zero mass jet flow is simulated by imposing a harmonically varying boundary condition on the wall surface.

In this work, the effect of synthetic jets for different angles of attack and different frequencies ranging from 200 Hz to 800 Hz was assessed. The application of the synthetic jet actuators is based in their ability to energize the boundary layer, thereby providing significant increase in …

3d Aerodynamic Optimization Of Nrel Vi Wind Turbine Blade For Increased Power Output And Visualization Of Flow Characteristics, Tsewang Rabga Shrestha

Doctoral Dissertations and Master's Theses

The thesis focuses on the aspect of optimization of NREL VI wind turbine blade for increased power output using commercial solver ANSYS 14.5. The power curve obtained from BEMT, Baseline NREL VI CFD Simulations and Optimized Blade Simulations are compared with experimental results. Over prediction is observed in the theoretical result while computational analysis under predicts power produced at post stall region. Parameter correlation and sensitivity analysis study relates the effectiveness of design parameters on the objective outcome. Scatter plots and Determination Matrix indicate the problem setup as non-linear quadratic. Adaptive Single Objective Optimization algorithm is used for the optimization …

Slosh Damping With Floating Magnetoactive Micro-Baffles, Vijay Santhanam

Doctoral Dissertations and Master's Theses

Liquid sloshing within propellant tanks of launch vehicles and other major vehicles has been a major concern. Various methods have been utilized for the damping of slosh through Propellant Management Devices (PMD) accomplishing a wide range of results. Exploratory research conducted at the Embry-Riddle Aeronautical University Fuel Slosh Test Facility in development of an innovative PMD is presented. Embedding floating micro-baffles with a magnetoactive material such that the baffle can be manipulated when exposed to a magnetic field preserves the benefits of both floating and static baffle designs. Activated micro-baffles form a rigid layer at the free surface and provide …

Investigation Of Grid Adaptation To Reduce Computational Efforts For A 2-D Hydrogen-Fueled Dual-Mode Scramjet, Kam Keong Foo

Doctoral Dissertations and Master's Theses

A two-dimensional dual-mode scramjet flowpath is developed and evaluated using the ANSYS Fluent density-based flow solver with various computational grids. Results are obtained for fuel-off, fuel-on non-reacting, and fuel-on reacting cases at different equivalence ratios. A one-step global chemical kinetics hydrogen-air model is used in conjunction with the eddy-dissipation model. Coarse, medium and fine computational grids are used to evaluate grid sensitivity and to investigate a lack of grid independence. Different grid adaptation strategies are performed on the coarse grid in an attempt to emulate the solutions obtained from the finer grids. The goal of this study is to investigate …

Fluid-Structure Interaction And Multidisciplinary Design Analysis Optimization Of Composite Wind Turbine Blade, Naishadh G. Vasjaliya

Doctoral Dissertations and Master's Theses

A multidisciplinary design analysis optimization (MDAO) process is defined for a composite wind turbine blade to optimize its aerodynamic and structural performance by developing a fluid-structural interaction (FSI) system. The objectives are to maximize aerodynamic efficiency and structural robustness while reducing blade mass and total cost. In the previous research, a MDO process of a composite wind turbine blade has been pioneered as an effective process to develop structurally optimized blade design. Present MDAO process is defined in conjunction with structural and aerodynamic performance of the blade which is divided into three steps and the design variables considered are related …

Investigation Of Pulse Detonation Engines; Theory, Design And Analysis, Jeff Vizcaino

Doctoral Dissertations and Master's Theses

Detonation and constant volume combustion has been known to the scientific community for some time but only recently has active research been done into its applications. Detonation based engines have received much attention in the last two decades because of its simple design and potential benefits to the aerospace industry. It is then the goal of this study to provide a background into detonation theory and application and establish the basis for future detonation based research at Embry-Riddle Aeronautical University. In this paper we will discuss the experimental aspects of building, testing, and analysis of a pulsed detonation tube …

Novel Airframe Design For The Dual-Aircraft Atmospheric Platform Flight Concept, Eric Michael Mckee

Doctoral Dissertations and Master's Theses

A high-altitude, long-endurance unmanned aerial airframe was designed for the innovative Dual-Aircraft Atmospheric Platform flight concept that exploits stratospheric wind velocity gradients to remain aloft indefinitely. Classical aircraft preliminary design techniques and high-fidelity tools were used to establish a baseline configuration.

Performance characteristics of numerous airfoil profiles were evaluated with two-dimensional flow software in an effort to determine the best-candidate airfoil for the unique application. Vortex-Lattice method tools were used to investigate the sensitivity of three-dimensional design parameters upon overall vehicle aerodynamic performance and determine both static and dynamic stability characteristics of the airframe. Performance capabilities of the finalized airframe …

High-Fidelity Modeling Of Airfoil Interaction With Upstream Turbulence, Jacob Brodnick

Doctoral Dissertations and Master's Theses

To supplement past research on low speed unsteady airfoil responses to upstream disturbances, this work proposes and investigates a method to generate a turbulent momentum source to be convected downstream and interact with an SD7003 airfoil in a high-fidelity numerical simulation. A perturbation velocity field is generated from a summation of Fourier harmonics and applied to the forcing function in the momentum terms of the Navier Stokes Equations. The result is a three-dimensional, divergence-free, convected turbulent gust with applied statistical parameters. A parametric study has been done in 2D and 3D comparing the resultant flow fields and airfoil interactions for …

Numerical Analysis Of Gun Barrel Pressure Blast Using Dynamic Mesh Adaption, Sathish Xavier

Doctoral Dissertations and Master's Theses

A Computational Fluid Dynamics (CFD) method has been applied to simulate the pressure blast of the projectile which is launched from a barrel and to investigate the pressure distribution and sound pressure level (dB) along different positions away from the gun axis and towards the fuselage of the aircraft. Fluent was employed to simulate the unsteady flow using dynamic mesh with moving boundary. Most CFD based ballistics-model requires additional thermodynamic functions which must be derived from the Noble-Abel equation of state. The unsteady, axisymmetric Navier Stokes equation systems were numerically solved using the Advection Upstream Splitting Method (AUSM) scheme; with …

Development Of A Higher-Order Navier-Stokes Solver For Transient Compressible Flows, Arjun Vijayanarayanan

Doctoral Dissertations and Master's Theses

A higher‐order density based Navier‐Stokes solver was developed for 2‐Dimensional flows using the finite volume approach. The Van leer flux‐splitting technique was used to calculate the fluxes. The second‐order spatial accuracy was achieved using the variable extrapolation method developed by Van leer called the Montone Upstream Centered Scheme for Conservation Laws (MUSCL) approach. The code development was done using Matlab. The code was verified using two validation cases. Firstly, subsonic, transonic, and supersonic flows over the 2‐D bump were simulated, and the results of the code were compared to the results from Fluent. Secondly, the shock‐tube problem was chosen, and …