Aerospace Engineering Commons^™

Analysis And Design Of A Propulsion System Trade Study Tool For A Boeing 376 Series Communications Satellite, Kevin Dunk

Aerospace Engineering

No abstract provided.

Design, Fabrication, And Testing Of An Automotive Turbocharger-Based Gas Turbine Engine, John Kyle Thoma, Daniel Shehan, Benjamin Naravage, Jacob Melvin

Aerospace Engineering

A fully-functioning, self-sustaining gas turbine engine was designed and built. The engine was constructed around a Holset HE351 VGT automobile turbocharger, containing compressor and turbine assemblies on a common shaft. Other components of the engine were either purchased or designed and fabricated in-house. During initial testing of the completed engine, the turbocharger, however, was found to have extensive damage to the internal oil seals, and so the project could not be completed as planned. Instead, the combustor design and fabrication was completed for stand-alone testing. The combustion chamber was designed so that the flame tube could be easily changed out …

Numerical Examination Of Flow Field Characteristics And Fabri Choking Of 2d Supersonic Ejectors, Brett G. Morham

Master's Theses

An automated computer simulation of the two-dimensional planar Cal Poly Supersonic Ejector test rig is developed. The purpose of the simulation is to identify the operating conditions which produce the saturated, Fabri choke and Fabri block aerodynamic flow patterns. The effect of primary to secondary stagnation pressure ratio on the efficiency of the ejector operation is measured using the entrainment ratio which is the secondary to primary mass flow ratio.

The primary flow of the ejector is supersonic and the secondary (entrained) stream enters the ejector at various velocities at or below Mach 1. The primary and secondary streams are …

Smore Phase 2: An Upgrade In Valve Systems & Startup Procedure For A Small Methanol Oxygen Liquid Rocket Engine, Christian Soria

Aerospace Engineering

A Methanol-Oxygen liquid rocket engine was designed and manufactured under the California Polytechnic State University Aerospace Department by students in a graduate level rocket propulsion class. The SMORE, previously known as the KORE, is now in an ongoing testing and developing stage with plans to incorporate it into the aerospace undergraduate propulsion lab. Phase 2 of the liquid rocket engine development is to produce a start-up procedure that will improve the safety due to manual operation and poor ignition conditions. A propane ignition system along with the implementation of electrically operated solenoid valves to control the fuels and oxidizer were …

An Investigation On Pulsing Performance Of Mn Class Bi-Propellant Thrusters, Carlos Francisco Gomez

Open Access Theses & Dissertations

With the advancement of technology and machining methods, considerable attention has been focused in manufacturing micro thrusters for micro spacecraft applications (Yetter et al, 2003). Micro propulsion systems are currently being investigated for Miniature Kill Vehicles (MKV) and Micro Satellite Systems (MSS) with an emphasis in reducing weight and cost but without affecting performance. Reducing the weight seems practical when reducing the size of the propulsion system, but problems are encountered with system design.

In addition, propulsion requirements strongly influence choice in propellant and complexity. A thorough understanding of stabilizing thrust levels and the ability to control the propulsion system …

Unmanned Aircraft System Propulsion Systems Technology Survey, Christopher Griffis, Timothy Wilson, Jeffrey Schneider, Peter Pierpont

Publications

This technology survey is an investigation of various propulsion systems used in Unmanned Aircraft Systems (UAS). Discussed are existing and near-future propulsion mechanisms of UAS, such as reciprocating piston engines, Wankel rotary engines, gas turbine engines, rocket-powered systems, electric motors, and battery-based systems. Also discussed are systems that use proton exchange membrane fuel cells, photovoltaics, ultracapacitors, and propellers. Each system is described in reference to a larger conceptual framework, with instances and profiles of existing UAS employing the system being described. Advantages and disadvantages of each type of propulsion system are identified along with associated technical issues and their respective …

Propulsion Enhancement Contributions To The Performance Of Space Launch Vehicles, Russell H. Edwards

Mechanical & Aerospace Engineering Theses & Dissertations

A research effort has been undertaken to investigate critical aspects of launch vehicle performance as affected by variations in specific launch vehicle parameters. The major portion of the study involves liquid propellant systems. However, since solid propellant systems also play a role in today's launch systems, a representative solid-propellant launch vehicle has also been analyzed. The research undertaken determined that the payload capability of a space launch vehicle, or, conversely, the vehicle total liftoff mass, is highly sensitive to the manner in which the space launch vehicle is staged. The research has led to the development and programming of a …

Solid State Aircraft Concept Overview, M. Shahinpoor, P. Jenkins, C. Smith, Kakkattukuzhy M. Isaac, T. Dalbello, Anthony Colozza

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Due to recent advances in polymers, photovoltaics, and batteries a unique type of aircraft may be feasible. This is a "solid-state" aircraft, with no conventional mechanical moving parts. Airfoil, propulsion, energy production, energy storage and control are combined in an integrated structure. The key material of this concept is an ionic polymeric-metal composite (IPMC) that provides source of control and propulsion. This material has the unique capability of deforming in an electric field and returning to its original shape when the field is removed. Combining the IPMC with thin-film batteries and thin-film photovoltaics provides both energy source and storage in …