Aerospace Engineering Commons^™

Measurement Sensitivity In Tapping-Mode Atomic Force Microscopy Using A Bi-Harmonic Drive Signal, Santosh R. Kodandarama, Douglas A. Bristow

Mechanical and Aerospace Engineering Faculty Research & Creative Works

In tapping mode atomic force microscopy, surface features are measured indirectly via the amplitude of the tapping cantilever. a change in surface profile is detectable only if it results in an amplitude change that is significant enough to be measured by the optics. Previous works have focused on improving sensitivity through the system's Q-factor, either by changing physical cantilever properties or using feedback control, but those approaches undesirably slow down the dynamic response. in this work we take a novel approach to sensitivity amplification by reshaping the tapping trajectory. by shaping the trajectory so that the probe spends a greater …

An Investigation On Pulsing Performance Of Mn Class Bi-Propellant Thrusters, Carlos Francisco Gomez

Open Access Theses & Dissertations

With the advancement of technology and machining methods, considerable attention has been focused in manufacturing micro thrusters for micro spacecraft applications (Yetter et al, 2003). Micro propulsion systems are currently being investigated for Miniature Kill Vehicles (MKV) and Micro Satellite Systems (MSS) with an emphasis in reducing weight and cost but without affecting performance. Reducing the weight seems practical when reducing the size of the propulsion system, but problems are encountered with system design.

In addition, propulsion requirements strongly influence choice in propellant and complexity. A thorough understanding of stabilizing thrust levels and the ability to control the propulsion system …

Studies Of Dynamic Crack Propagation And Crack Branching With Peridynamics, Youn Doh Ha, Florin Bobaru

Department of Engineering Mechanics: Faculty Publications

In this paper we discuss the peridynamic analysis of dynamic crack branching in brittle materials and show results of convergence studies under uniform grid refinement (m-convergence) and under decreasing the peridynamic horizon (δ-convergence). Comparisons with experimentally obtained values are made for the crack-tip propagation speed with three different peridynamic horizons.We also analyze the influence of the particular shape of themicro-modulus function and of different materials (Duran 50 glass and soda-lime glass) on the crack propagation behavior. We show that the peridynamic solution for this problem captures all the main features, observed experimentally, of dynamic crack propagation and branching, as well …

Influence Of Interactions Between Turbulence And Radiation On Transmissivities In Hypersonic Turbulent Boundary Layers, A. M. Feldick, L. (Lian) Duan, M. F. Modest, M. P. Martín, D. A. Levin

Mechanical and Aerospace Engineering Faculty Research & Creative Works

In the current paper, a high-fidelity large eddy simulation solver is coupled to our modified line-by-line radiative transport equation solver to study the effects of absorption turbulence-radiation interations in a hypersonic turbulent boundary layer, representative of the Orion CEV entering Earth's atmosphere, at peak heating condition. The turbulent and radiation fields represent extreme conditions typical of Orion, as the simulated boundary layer represents the region of high turbulence coupled to region of highest incident radiation. A simplification in the calculation of molecular spectra with a single temperature property database in allows for tractable calculation of spectral properties. A comparison of …

Direct Numerical Simulation Of Hypersonic Turbulent Boundary Layers. Part 2. Effect Of Wall Temperature, L. (Lian) Duan, I. Beekman, M. P. Martín

Mechanical and Aerospace Engineering Faculty Research & Creative Works

In this paper, we perform direct numerical simulation (DNS) of turbulent boundary layers at Mach 5 with the ratio of wall-to-edge temperature T w/T ℘ from 1.0 to 5.4 (Cases M5T1 to M5T5). The influence of wall cooling on Morkovin's scaling, Walz's equation, the standard and modified strong Reynolds analogies, turbulent kinetic energy budgets, compressibility effects and near-wall coherent structures is assessed. We find that many of the scaling relations used to express adiabatic compressible boundary-layer statistics in terms of incompressible boundary layers also hold for non-adiabatic cases. Compressibility effects are enhanced by wall cooling but remain insignificant, and the …

Direct Detection Of No Produced By High-Temperature Surface-Catalyzed Atom Recombination, Dušan A. Pejaković, Jochen Marschall, Lian Duan, Maria P. Martin

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The surface-catalytic recombination of oxygen and nitrogen atoms to form nitric oxide was confirmed by the direct detection of product NO molecules, using single-photon laser-induced fluorescence spectroscopy. Experiments were performed from room temperature to 1200 K in a quartz diffusion-tube sidearm reactor enclosed in a high temperature tube furnace. Atomic nitrogen was generated using a microwave discharge, and atomic oxygen was produced via the rapid gas-phase titration reaction N + NO → O + N2. The use of isotopically labeled titration gases 15N16O and 15N18O allowed for the unambiguous identification of nitric oxide produced by the O + N surface …

Direct Numerical Simulation Of Hypersonic Turbulent Boundary Layers With Varying Freestream Mach Number, L. (Lian) Duan, I. Beekman, M. P. Mart́In

Mechanical and Aerospace Engineering Faculty Research & Creative Works

In this paper, the effects of freestream Mach number on the statistics and large-scale structures in compressible turbulent boundary layers are investigated using direct numerical simulations (DNS). DNS of turbulent boundary layers with nominal freestream Mach number ranging from 3 to 8 are performed. The validity of Morkovin's scaling, strong Reynolds analogy, and Walz's equation are assessed. We find that many of the scaling relations used to express compressible boundary layer statistics in terms of incompressible boundary layers still hold for the range of freestream Mach number considered. Compressibility effects are enhanced with increasing freestream Mach number but remain insignificant, …

Guidance And Control For Chase Uav Via Sliding Mode Approach, Takeshi Yamasaki, S. N. Balakrishnan

Mechanical and Aerospace Engineering Faculty Research & Creative Works

This study focuses on integrated guidance and control for a chasing UAV against a maneuvering target. a sliding mode approach is selected to develop the integrated guidance and control using a full model of nonlinear, rigid body, 6 Degree-Of-Freedom equations of motion including nonlinear aerodynamics for the target-following capability and maneuverability enhancement against uncertain target maneuvers. Intermediate control variables for the integrated guidance and control system are carefully selected and approximated time derivatives of a sliding surface are applied such that a sliding surface structure is simple and sufficient to propagate the actuator input to the sliding surface in order …

Development Of An Optical Fiber-Based Corrosion Detection Sensor Based On Laser Light Reflection, Manjunatha Shenoy

Mechanical and Aerospace Engineering Theses - Archive

Corrosion plays a detrimental effect on the structural integrity of many engineering structures. It can compromise the safe operation of these structures by forming corrosion pits that deteriorates the structural surfaces and causes stress concentrations. Therefore, it is critical that corrosions are detected before structural integrity is compromised and repair becomes economically prohibitive. However, corrosions usually occur at intricate places that are hard to inspect visually. Manual inspection of the structures for corrosions requires dismantling the structures, which incurs high maintenance costs and could potentially cause damage to the components. One approach to reduce this cost is to detect and …

An Integration Of A Modern Flight Control System Design Technique Into A Conceptual Design Stability And Controls Tool, Aeromech, Amen Omoragbon

Mechanical and Aerospace Engineering Theses - Archive

The aircraft conceptual design (CD) phase is the most abstract, thus challenging phase of the entire aircraft design process. It is the responsibility of the CD engineer to identify and then to explore various aircraft concepts with the goal of arriving at the most promising concept for further evaluation. During this early design phase, the discipline stability and control tends to be underrepresented due to the lack of non-linear aerodynamic and inertia data. The methodology and software AeroMech is a vehicle configuration independent aircraft conceptual design stability and control tool, developed to help the conceptual designer to address stability and …

Imbalance Response Of A Four Degree Of Freedom Rigid Rotor Supported By Hybrid Three Pad Air Foil Bearing, Prajwal Krishna Shetty

Mechanical and Aerospace Engineering Theses - Archive

Air foil bearings (AFB's) are widely used in small to midsized turbomachinery. They provide safer, cleaner and cheaper bearing operation. They are simple in construction, offer very low drag friction and have very high reliability at high speed operations. A major advantage of air foil bearings compared to conventional rigid surface bearings is their superior dynamic performance in rotor bearing systems. Since there is no contact between the rotor and bearing surface, the air foil bearings have a higher service life compared to rigid surface bearings. Hybrid AFB's operate under both hydrodynamic and hydrostatic condition. The present study is a …

Thermal Performance Of Cryogenic Multilayer Insulation At Various Layer Spacings, Wesley Louis Johnson

Electronic Theses and Dissertations

Multilayer insulation (MLI) has been shown to be the best performing cryogenic insulation system at high vacuum (less than 10-3 torr), and is widely used on spaceflight vehicles. Over the past 50 years, many numerous investigations of MLI have yielded a general understanding of the many variables associated with MLI. MLI has been shown to be a function of variables such as warm boundary temperature, the number of reflector layers, and the spacer material in between reflectors, the interstitial gas pressure and the interstitial gas. Because conduction between reflectors increases with the thickness of the spacer material, and yet the …

Exomedicine Synthesis Paper, Rita Briggs

Robert "Bob" Twiggs STEM Education Collection

A report by Rita Briggs titled "Exomedicine Synthesis Paper" from 2010.

Analysis Of The Theta-D Filter As Applied To Hit-To-Kill Interceptors And Satellite Orbit Determination, Michael W. Dancer

Masters Theses

"When designing feedback control systems, there is often a need for estimation methods that provide system information that is not readily available via sensors placed within the system. In many cases a sensor that measures a particular system state either does not exist or is prohibitively expensive. In addition, all realistic systems contain some degree of nonlinearity. This thesis focuses on two such cases: missile guidance with bearings-only measurements and GPS satellite orbit determination. In each case, a new nonlinear filter, the [theta]-D method, is used and evaluated for its performance in providing the necessary estimation. To aid the filter …

Management Of A University Satellite Program With Focus On A Refrigerant-Based Propulsion System, Shawn W. Miller

Masters Theses

"The Missouri University of Science and Technology Satellite (M-SAT) design team has established a satellite program to develop a pair of satellites to perform an autonomous formation flight mission. The resulting configuration was assembled for the Air Force Research Lab University Nanosat Program. This document, written by the Program Manager and former member of the Propulsion subsystem, is a description of the management process used by the team to develop a satellite configuration. Included in the document is a discussion of team organization, techniques for managing a program, and lessons learned during the 2007 to 2008 timeframe. The managing techniques …

A Numerical Investigation Of Flowfield Modification In High-Speed Airbreathing Inlets Using Energy Deposition, Matthew Flynn Rohweder

Masters Theses

"Energy deposition in front of dual-mode ram/scramjet engines is numerically investigated utilizing two-dimensional CFD for its potential to modify inlet/isolator flow-fields for engine start/unstart control and for its general potential for generating large-scale flow-field modification in such flows. A simplified (high Mach number) constant-area duct geometry is initially defined in order to test the feasibility of the concept; the results from this initial investigation demonstrates possible beneficial effects of depositing energy upstream of a thermally choked duct in terms of causing massive changes in flow patterns, including the reestablishment of supersonic flow throughout the duct. This study is followed by …

Integration And Test Of A Refrigerant-Based Cold-Gas Propulsion System For Small Satellites, Ryan Alan Pahl

Masters Theses

"Due to the launch safety constraints placed on university-built small satellites, designing a low-cost propulsion system to meet mission requirements presents a significant challenge to aspiring student engineers. The Missouri University of Science and Technology is currently developing a low-cost, two-phase propulsion system using the refrigerant R-134a as the propellant that can be stored at low pressures while still providing sufficient performance to meet mission goals. The purpose of this study is to present the testing results of a refrigerant-based cold gas system utilizing R-134a as a saturated liquid propellant and the ability to design this system to be portable …

Quantification Of Uncertainty In Aerodynamic Heating Of A Reentry Vehicle Due To Uncertain Wall And Freestream Conditions, Benjamin R. Bettis

Masters Theses

"The primary focus of this study is to demonstrate an efficient approach for uncertainty quantification of surface heat flux to the spherical non-ablating heatshield of a generic reentry vehicle due to epistemic and aleatory uncertainties that may exist in various parameters used in the numerical solution of hypersonic, viscous, laminar blunt-body flows with thermo-chemical non-equilibrium. Two main uncertainty sources were treated in the computational fluid dynamics (CFD) simulations: (1) aleatory uncertainty in the freestream velocity and (2) epistemic uncertainty in the recombination efficiency for a partially catalytic wall boundary condition. The Second-Order Probability utilizing a stochastic response surface obtained with …

Thrust Measurement Of Dielectric Barrier Discharge Plasma Actuators And Power Requirements For Aerodynamic Control, Joseph William Ferry

Masters Theses

"Plasma-based aerodynamic actuators are of interest to researchers because they do not require moving control surfaces or a source of pressurized air to modify a flow field. Dielectric barrier discharge (DBD) plasma actuators have the added advantages of simple installation and low power consumption.

DBD plasma actuators are AC devices. This work measured actuator power consumption and thrust production for driving frequencies between 1 and 18 kHz, and for driving voltages of 6 and 9 kV peak to peak. The actuator consumed between 3 and 22 W of power and produced thrust levels between 0.05 and 0.2 mN per meter …

Laminar-Turbulent Transition For Attached And Separated Flow, Qian Zhang

University of Kentucky Doctoral Dissertations

A major challenge in the design of turbomachinery components for aircraft gas turbine engines is high cycle fatigue failures due to flutter. Of particular concern is the subsonic/transonic stall flutter boundary which occurs at part speed near the stall line. At these operating conditions the incidence angle is large and the relative Mach number is high subsonic or transonic. Viscous effects dominate for high incidence angles.

In order to predict the flutter phenomena, accurate calculation of the steady and unsteady aerodynamic loading on the turbomachinery airfoils is necessary. The development of unsteady aerodynamic models to predict the unsteady forces and …

Fusion Of Imprecise Qualitative Information, Florentin Smarandache, Xinde Li, Xianzhong Dai, Jean Dezert

Branch Mathematics and Statistics Faculty and Staff Publications

In this paper, we present a new 2-tuple linguistic representation model, i.e. Distribution Function Model (DFM), for combining imprecise qualitative information using fusion rules drawn from Dezert-Smarandache Theory (DSmT) framework. Such new approach allows to preserve the precision and efficiency of the combination of linguistic information in the case of either equidistant or unbalanced label model. Some basic operators on imprecise 2-tuple labels are presented together with their extensions for imprecise 2-tuple labels. We also give simple examples to show how precise and imprecise qualitative information can be combined for reasoning under uncertainty. It is concluded that DSmT can deal …

Fusion Of Sources Of Evidence With Different Importances And Reliabilities, Florentin Smarandache, Jean Dezert, J.M. Tacnet

Branch Mathematics and Statistics Faculty and Staff Publications

This paper presents a new approach for combining sources of evidences with different importances and reliabilities. Usually, the combination of sources of evidences with different reliabilities is done by the classical Shafer’s discounting approach. Therefore, to consider unequal importances of sources, if any, a similar reliability discounting process is generally used, making no difference between the notion of importance and reliability. In fact, in multicriteria decision context, these notions should be clearly distinguished. This paper shows how this can be done and we provide simple examples to show the differences between both solutions for managing importances and reliabilities of sources. …

Processing Of Zrb2-Zrc-Zrxsiy Ceramic By Reactive Metal Penetration, Nischel B. Maheswaraiah

Open Access Theses & Dissertations

The processing of ZrB2-ZrC-ZrxSiy composite by reactive metal penetration was investigated as a successor to the ZrB2-SiC composites for hypersonic vehicles application, which cannot be used for extended time at temperatures greater than 1600C due to formation of SiO and CO gases. Zirconium (Zr), zirconium disilicide (ZrSi2), and boron carbide (B4C) were reacted in graphite crucibles for 60, 120, 180, and 240 minutes. Microscopy and x-ray diffraction (XRD) deduced the formation of a heterogeneous microstructure of ZrB2-ZrC-ZrxSiy precipitates surrounded by a solidified Zr-Si melt. Unreacted boron carbide was observed in samples held at 1860C for 60 minutes and 120 minutes, …

Microstructure Investigation Of Al-Rich Titanium Aluminum Alloys, David Pham

Open Access Theses & Dissertations

The microstructures of Ti-Al alloys with 70-80 wt% Al were investigated. Aluminum wire (99.999%) and TiH₂ powder (99.7%) were used to produce the sample compositions inside a vertical tube furnace at 1600^oC in an Ar atmosphere. Argon is purified through a dehumidification and deoxidation system. Magnesium perchlorate Mg(ClO₄)₂ acts as a desiccant and titanium sponge pulls oxygen from the Ar in furnaces operating at 800^oC and 750^oC. X-ray diffraction and an optical microscope are used to identify phases and compositions

Development Of A Micro-Catbed For Miniature Thrusters, Chance Paul Garcia

Open Access Theses & Dissertations

The goal of this work is to develop a micro catalytic bed for miniature thrusters. A test bed was constructed for experimental testing to characterize several parts of the micro catalytic bed. The reactant fluid studied is 90% Hydrogen Peroxide (H2O2) by weight. Three different cross sectional area designs were tested to determine decomposition efficiency, temperature reaction propensity, optimum flow rate, and temperature distribution across each bed. The products of decomposition were condensed to measure the oxygen released from decomposition. The results will be used to develop the basis for a micro catalytic bed design to implement into future miniature …

Black Carbon Over Mexico: The Effect Of Atmospheric Transport On Mixing State, Mass Absorption Cross-Section, And Bc/Co Ratios, R. Subramanian, G. L. Kok, D. Baumgardner, A. Clarke, Y. Shinozuka, T. L. Campos, C. G. Heizer, B. B. Stephens, B. De Foy, Paul B. Voss, R. A. Zaveri

Engineering: Faculty Publications

A single particle soot photometer (SP2) was operated on the NCAR C-130 during the MIRAGE campaign (part of MILAGRO), sampling black carbon (BC) over Mexico. The highest BC concentrations were measured over Mexico City (sometimes as much as 2μg/m3) and over hillfires to the south of the city. The age of plumes outside of Mexico City was determined using a combination of HYSPLIT trajectories, WRF-FLEXPART modeling and CMET balloon tracks. As expected, older, diluted air masses had lower BC concentrations. A comparison of carbon monoxide (CO) and BC suggests a CO background of around 65 ppbv, and a background-corrected BC/COnet …

Compact Survey And Inspection Day/Night Image Sensor Suite For Small Unmanned Aircraft Systems (Eyepod), Alan Bird, Scott A. Anderson, Dale Linne Von Berg, Morgan Davidson, Niel Holt, Melvin Kruer, Michael L. Wilson

Space Dynamics Laboratory Publications

EyePod is a compact survey and inspection day/night imaging sensor suite for small unmanned aircraft systems (UAS). EyePod generates georeferenced image products in real-time from visible near infrared (VNIR) and long wave infrared (LWIR) imaging sensors and was developed under the ONR funded FEATHAR (Fusion, Exploitation, Algorithms, and Targeting for High-Altitude Reconnaissance) program. FEATHAR is being directed and executed by the Naval Research Laboratory (NRL) in conjunction with the Space Dynamics Laboratory (SDL) and FEATHAR’s goal is to develop and test new tactical sensor systems specifically designed for small manned and unmanned platforms (payload weight < 50 lbs). The EyePod suite consists of two VNIR/LWIR (day/night) gimbaled sensors that, combined, provide broad area survey and focused inspection capabilities. Each EyePod sensor pairs an HD visible EO sensor with a LWIR bolometric imager providing precision geo-referenced and fully digital EO/IR NITFS output imagery. The LWIR sensor is mounted to a patent-pending jitter-reduction stage to correct for the high-frequency motion typically found on small aircraft and unmanned systems. Details will be presented on both the wide-area and inspection EyePod sensor systems, their modes of operation, and results from recent flight demonstrations.

Pilot Source Study: An Analysis Of Pilot Backgrounds And Subsequent Success In Us Regional Airline Training Programs, Guy M. Smith, David A. Newmyer, Elizabeth Bjerke, Mary Niemczyk, Raymond A. Hamilton

Applied Aviation Sciences - Daytona Beach

The 2010 Pilot Source Study, commissioned to research the success of pilots in initial training for Part 121 operations, analyzed the training performance of 2,156 new-hire pilots in the years 2005-2009. Six regional airlines provided data that was mined from human resource and pilot training files. Five university researchers independently analyzed the data and integrated their results. The study expressed success in terms of fewer extra training events and fewer non-completions in regional airline training. Statistically, the best performing pilots were those who had flight instructor certificates, graduated from collegiate accredited flight programs, received advanced (post-Private) pilot training in college, …

Analysis Of Wake Vortices Of A Medium Range Twin-Propeller Military Cargo Aircraft Using Statistically Designed Experiments, Burhan Sahin

Mechanical & Aerospace Engineering Theses & Dissertations

An experimental study was initiated to analyze the trajectories of the streamwise vortices behind the wing tip and flap of a medium range and propeller driven twin-engine military cargo aircraft. The model used for the experimental study was a generic, high wing and half model of a propeller driven aircraft and mounted within Old Dominion University's Low Speed Wind Tunnel where the wind tunnel flow speed was set to constant value of 9 m/sec. The main purpose of the study was to reach regression models for the motion and vorticity strength of both vortices under varying factors such as angle …

Active Control Of Shocks And Sonic Boom Ground Signal, Bedri Yagiz

Mechanical & Aerospace Engineering Theses & Dissertations

The manipulation of a flow field to obtain a desired change is a much heightened subject. Active flow control has been the subject of the major research areas in fluid mechanics for the past two decades. It offers new solutions for mitigation of shock strength, sonic boom alleviation, drag minimization, reducing blade-vortex interaction noise in helicopters, stall control and the performance maximization of existing designs to meet the increasing requirements of the aircraft industries. Despite the wide variety of the potential applications of active flow control, the majority of studies have been performed at subsonic speeds. The active flow control …