Aerospace Engineering Commons^™

The Effect Of The Fastener Of Different Configuration Composite Panels On Failure Analysis, Robert Austin

Master's Theses

This study presents the effect of the stacking sequence and fiber orientation on a composite sandwich panel subjected to static in-plane bolt loading. Six plates were constructed with laminates of unidirectional carbon fiber and cross ply weaves of fiberglass. The orientations that were examined included 0, +/- 45, and 90 degrees. Half of the plates had fiberglass lamina on the outside of the laminate while the other three plates had the carbon fiber on the outside. Experimental and analytical tests were performed to determine the best orientations and stacking sequence.

For the numerical analysis, plates with fibers oriented at +/- …

Shielding Effectiveness Of Superalloy, Aluminum, And Mumetal Shielding Tapes, Cindy Suit Cheung

Master's Theses

Using MIL-HDBK-419A, MATLAB and Nomographs, Shielding Effectiveness for the Magnetic Field, Electric Field, and Plane Wave were calculated over a frequency range from 10 Hz to 1 GHz. The three shielding tapes used included superalloy, aluminum, and mumetal. Calculations for Shielding Effectiveness involve the computation of Absorption Loss, Reflection Loss, and Re-Reflection Correction Factor. From the outcome of the calculations, it was suitable to conclude that all three metals fulfill the 40 dB Shielding Effectiveness requirements for SGEMP fields for frequencies greater or equal to 1 MHz. Accordingly, all three shielding tapes provide at least 40 dB of shielding to …

A System For Measuring The Lift And Drag Forces Of A Spinning Golf Ball Held Fixed Within A Wind Tunnel, Ryan R. Miller

Master's Theses

A system was designed, built and tested in order to test the aerodynamic properties of a standard golf ball in a wind tunnel manufactured by ELD, Inc. model 406(B). The system consists of a rotating shaft, on which the golf ball is attached, connected to a two-axis force transducer. Additionally, an automated data acquisition system was built for enhanced precision of measurements. Data for wind speeds up to 160 ft/s and rotational speeds up to 8,600 rpm were obtained and analyzed. The purpose of the designed apparatus was to allow for studies to better understand the lift and drag coefficients …

Application Of Parent-Child Uav Tasking For Wildfire Detection And Response, Stephen T. Kubik

Master's Theses

In recent years, unmanned aerial vehicles (UAVs) have become a dominant force in the aerospace industry. Recent technological developments have moved these aircraft from remote operation roles to more active response missions. Of particular interest is the possibility of applying UAVs toward solving complex problems in long-endurance missions. Under that belief, the feasibility of utilizing UAVs for wildfire detection and response was investigated in a partnership that included NASA’s Aeronautics Research Mission Directorate and Science Mission Directorate, and the United States Forest Service. Under NASA’s Intelligent Mission Management (IMM) project, research was conducted to develop a mission architecture that would …

Control And Sensor Development On A Four-Wheel Pyramidal Reaction Wheel Platform, Jeffery Jay Logan

Master's Theses

The Pyramidal Reaction Wheel Platform, or PRWP, is used to simulate three-axis controls in a torque free space-like environment. The primary purpose of the system will be to evaluate the effects of conjoining sensors to maximize pointing accuracy. Furthermore, the system will incorporate a star tracker in conjunction with a Simulated Star Field (SSF) to better estimate the PRWP orientation. For the sake of this document, however, the goal is to implement a gyroscope, wheel rate sensors, and a make-shift accelerometer—to the PRWP—and integrate a controls algorithm such that three-axis controls are achieved for the PRWP. Three sensors were either …

Cfd As Applied To The Design Of Short Takeoff And Landing Vehicles Using Circulation Control, Tyler M. Ball

Master's Theses

The ability to predict the distance required for an aircraft to takeoff is an essential component of aircraft design. It involves aspects related to each of the major aircraft systems: aerodynamics, propulsion, configuration, structures, and stability and control. For an aircraft designed for short takeoffs and landings (STOL), designing the aircraft to provide a short takeoff distance, or more precisely the balanced field length (BFL), often leads to the use of a powered lift technique such as circulation control (CC). Although CC has been around for many years, it has never been used on a production aircraft. This is in …