Attitude Estimation For A Gravity Gradient Momentum Biased Nanosatellite, Arash Mehrparvar

Master's Theses

Attitude determination and estimation algorithms are developed and implemented in simulation for the Exocube satellite currently under development by PolySat at Cal Poly. A mission requirement of ±5˚ of attitude knowledge has been flowed down from the NASA Goddard developed payload, and this requirement is to be met with a basic sensor suite and the appropriate algorithms. The algorithms selected in this work are TRIAD and an Extended Kalman Filter, both of which are placed in a simulation structure along with models for orbit propagation, spacecraft kinematics and dynamics, and sensor and reference vector models. Errors inherent from sensors, orbit …

Qualitative Methods Used To Develop And Characterize The Circulation Control System On Cal Poly's Amelia, Eric N. Paciano

Master's Theses

The circulation control system onboard Cal Poly's Advanced Model for Extreme Lift and Improved Aeroacoustics was a critical component of a highly complex wind tunnel model produced in order to fulfill the requirements of a NASA Research Announcement awarded to David Marshall of the Aerospace Engineering Department. The model was based on a next generation, 150 passenger, regional, cruise efficient, short take-off and landing concept aircraft that achieved high lift through circulation control wings and over-the-wing mounted engines. The wind tunnel model was 10-ft in span, used turbine propulsion simulators, and had a functioning circulation control system driven from tunnel …

Design, Fabrication And Test Of An Operationally Responsive Aircraft With Niirs Evaluated Imager, Colin Burt

Master's Theses

Unmanned Aerial Systems (UAS) are a growing asset. Currently UAS are on the cutting edge with resources being spent developing the capabilities mostly for military use. This project is intended to create a system for non-defense customers. Specifically, the Operationally Responsive Aircraft (ORA) will appeal to academic institutions, individual consumers, future customers new to the UAS industry, as well as anybody trying to get airtime for custom sensors.

The system developed in this project utilizes dual aluminum external payload bays attached to a ParkZone Radian aircraft. Each external payload bay can contain approximately 500 $\text{cm}^3$, with a height and width …

A Study Of The Collisional Evolution Of Orbital Debris In Geopotential Wells And Geo Disposal Orbits, Christina R. Diaz

Master's Theses

This thesis will present the effects of the orbital debris evolution in two key areas: the geosynchronous disposal orbit regime known as “graveyard” and the two geopotential wells found in 105◦ W and 75◦ E longitude bins. After developing a GEO specific orbit propagator for NASA Johnson Space Center’s Orbital Debris Of- fice, collisions were simulated throughout these regimes using a low velocity breakup model. This model considered the effects of perturbations particularly non-spherical Earth effects (specifically sectorial and zonal harmonics), lunar effects, third body effects and solar radiation pressure effects. The results show that CDPROP does well in simulating …

The Feasibility And Application Of Observing Small Leo Satellites With Amateur Telescopes, Brock Schmalzel

Master's Theses

This thesis demonstrates that any individual can provide relevant observational data to further research efforts within the Aerospace community, through the use of amateur telescopes. A Meade LX200 12 in. telescope and Lumenera Skynyx 2.0 camera were utilized to observe small LEO satellites, using a well-documented point-and-wait staring method. Over a period of three months, a total of 186 observation attempts were made resulting in 97 successful captures. From the gathered data, three possible aerospace applications were analyzed: validation of a satellite brightness prediction model, angles-only orbit determination including extended Kalman filtering, and temporal error growth in TLE-based orbit propagation. …

Thermal Analysis Of A Monopropellant Micropropulsion System For A Cubesat, Erin C. Stearns

Master's Theses

Propulsive capabilities on a CubeSat are the next step in advancement in the Aerospace Industry. This is no longer a quest that is being sought by just university programs, but a challenge that is being taken on by all of the industry due to the low-cost missions that can be accomplished. At this time, all of the proposed micro-thruster systems still require some form of development or testing before being flight-ready. Stellar Exploration, Inc. is developing a monopropellant micropropulsion system designed specifically for CubeSat application.

The addition of a thruster to a CubeSat would expand the possibilities of what CubeSat …

Microphone-Based Pressure Diagnostics For Boundary Layer Transition, Spencer Everett Lillywhite

Master's Theses

An experimental investigation of the use low-cost microphones for unsteady total pressure measurement to detect transition from laminar to turbulent boundary layer flow has been conducted. Two small electret condenser microphones, the Knowles FG-23629 and the FG-23742, were used to measure the pressure fluctuations and considered for possible integration with an autonomous boundary layer measurement system. Procedures to determine the microphones’ maximum sound pressure levels and frequency response using an acoustic source provided by a speaker and a reference microphone. These studies showed that both microphones possess a very flat frequency response and that the max SPL of the FG-23629 …

A Generic Decision Making Framework For Autonomous Systems, Connor Lange

Master's Theses

With the rising popularity of small satellites, such as CubeSats, many smaller institutions previously incapable of developing and deploying a spacecraft have starting to do so. Institutions with a history of space flight, such as NASA JPL, have begun to put projects on CubeSats that would normally fly on much larger satellites. As a result, the institutions with space flight heritage have begun to port spacecraft software that was previously designed for much larger and more complex satellites to the CubeSat platform. Unfortunately for universities, who are the majority of all institutions devel- oping CubeSats, these ported systems are too …

Feasibility Of Microsatellite Active Debris Removal Systems, Karsten J. James

Master's Theses

Space debris has become an increasingly hazardous obstacle to continued spaceflight operations. In an effort to mitigate this problem an investigation of the feasibility of a microsatellite active debris removal system was conducted. Through proposing a novel concept of operation, utilizing a grapple-and-tug system architecture, and by analyzing each resultant mission phase in the frame of a representative example, it was found that microsatellite scale systems are capable of fulfilling the active debris removal mission. Analysis of rendezvous, docking, control and deorbit mission requirements determined that the design of a grapple-and-tug system will be driven by sizing of the propellant …

Micrometeoroid Fluence Variation In Critical Orbits Due To Asteroid Disruption, Eliot Dan Aretskin-Hariton

Master's Theses

Micrometeoroids and orbital debris (MMOD) is a growing issue with international importance. Micrometeoroids are naturally occurring fragments of rock and dusk that exist throughout the solar system. Orbital debris is human made material like rocket bodies, paint flakes, and the effluent of spacecraft collisions. Even small MMOD particles on the order of 1 cm in diameter have the potential to destroy critical spacecraft systems. Because of this, MMOD is a threat to all spacecraft in orbit. Even governments that most sternly oppose US international policy have a stake when it comes to minimizing MMOD flux. Space-based assets are essential to …

Design, Fabrication, And Testing Of An Emr Based Orbital Debris Impact Testing Platform, Jeffrey J. Maniglia Jr.

Master's Theses

This paper describes the changes made from Cal Poly’s initial railgun system, the Mk. 1 railgun, to the Mk. 1.1 system, as well as the design, fabrication, and testing of a newer and larger Mk. 2 railgun system. The Mk. 1.1 system is developed as a more efficient alteration of the original Mk. 1 system, but is found to be defective due to hardware deficiencies and failure, as well as unforeseen efficiency losses. A Mk. 2 system is developed and built around donated hardware from the Naval Postgraduate School. The Mk. 2 system strove to implement an efficient, augmented, electromagnetic …

Improvement Of Electromagnetic Railgun Barrel Performance And Lifetime By Method Of Interfaces And Augmented Projectiles, Aleksey D. Pavlov

Master's Theses

Several methods of increasing railgun barrel performance and lifetime are investigated. These include two different barrel-projectile interface coatings: a solid graphite coating and a liquid eutectic indium-gallium alloy coating. These coatings are characterized and their usability in a railgun application is evaluated. A new type of projectile, in which the electrical conductivity varies as a function of position in order to condition current flow, is proposed and simulated with FEA software. The graphite coating was found to measurably reduce the forces of friction inside the bore but was so thin that it did not improve contact. The added contact resistance …

Characterization Of The Effects Of A Sun-Synchronous Orbit Slot Architecture On The Earth's Orbital Debris Environment, Connor David Noyes

Master's Theses

Low Earth orbit represents a valuable limited natural resource. Of particular interest are sun-synchronous orbits; it is estimated that approximately 44% of low Earth satellites are sun-synchronous. A previously developed sun-synchronous orbit slot architecture is considered. An in-depth analysis of the relative motion between satellites and their corresponding slots is performed. The long-term evolution of Earth's orbital environment is modeled by a set of coupled ordinary differential equations. A metric for quantifying the benefit, if any, of implementing a sun-synchronous architecture is developed. The results indicate that the proposed slot architecture would reduce the frequency of collisions between satellites in …

Uav Formation Flight Utilizing A Low Cost, Open Source Configuration, Christian W. Lopez

Master's Theses

The control of multiple unmanned aerial vehicles (UAVs) in a swarm or cooperative team scenario has been a topic of great interest for well over a decade, growing steadily with the advancements in UAV technologies. In the academic community, a majority of the studies conducted rely on simulation to test developed control strategies, with only a few institutions known to have nurtured the infrastructure required to propel multiple UAV control studies beyond simulation and into experimental testing. With the Cal Poly UAV FLOC Project, such an infrastructure was created, paving the way for future experimentation with multiple UAV control systems. …

Analysis And Mitigation Of The Cubesat Dynamic Environment, Steve M. Furger

Master's Theses

A vibration model was developed for CubeSats inside the Poly-Picosatellite Orbital Deployer (P-POD). CubeSats are fixed in the Z axis of deployers, and therefore resonate with deployer peaks. CubeSats generally start fixed in the X and Y axes, and then settle into an isolated position. CubeSats do not resonate with deployers after settling into an isolated position. Experimental data shows that the P-POD amplifies vibration loads when CubeSats are fixed in the deployer, and vibration loads are reduced when the CubeSats settle into an isolated position. A concept for a future deployer was proposed that isolates CubeSats from the deployer …

An Experimental Investigation Of The Stol Performance Of Cal Poly's Amelia In The Nfac, Jonathan Andrew Lichtwardt

Master's Theses

Results from Cal Poly's recent wind tunnel test, during the Winter of 2011-2012, in the 40- by 80-foot test section at the National Full-Scale Aerodynamics Complex (NFAC) at NASA Ames Research Center are presented. AMELIA, the Advanced Model for Extreme Lift and Improved Aeroacoustics, is the first full-span, cruise efficient, short take-off and landing (CESTOL) model incorporating leading- and trailing-edge blowing wing circulation control and over-the-wing mounted turbine propulsion simulators (TPS) to date. Testing of the 10 foot span model proved successful and was the result of a 5 year NASA Fundamental Aeronautics Program Research Announcement. The test generated extensive …

Enabling Rapid Conceptual Design Using Geometry-Based Multi-Fidelity Models In Vsp, Joel Brian Belben

Master's Theses

The purpose of this work is to help bridge the gap between aircraft conceptual design and analysis. Much work is needed, but distilling essential characteristics from a design and collecting them in an easily accessible format that is amenable to use by inexpensive analysis tools is a significant contribution to this goal. Toward that end, four types of reduced-fidelity or degenerate geometric representations have been defined and implemented in VSP, a parametric geometry modeler. The four types are degenerate surface, degenerate plate, degenerate stick, and degenerate point, corresponding to three-, two-, one-, and zero- dimensional representations of underlying geometry, respectively. …

Axisymmetric Air Augmented Methanol/Gox Rocket Mixing Duct Experimental Thrust Study, Kyle Jacob Johnson

Master's Theses

A hot-flow axisymmetric Air Augmented Rocket (AAR) test apparatus was constructed to test various mixing duct configurations at static conditions. Primary flow for the AAR was provided through a liquid methanol-gaseous oxygen bipropellant rocket. Experimental thrust measurements were recorded and propellant mass flow rates and chamber conditions were calculated using an iterative solver dependant on recorded propellant line stagnation pressures. Primary rocket flow produced thrust ranging from 14 to 17.9lbf. Primary mass flow rate through testing ranged from 0.071 to 0.085lbm/s with calculated chamber pressures between 298-362psia. Calculated primary flow velocity ranged from 6,600ft/s to 8,000ft/s depending on propellant pressure …

A Gravity Gradient, Momentum-Biased Attitude Control System For A Cubesat, Ryan J. Sellers

Master's Theses

ExoCube is the latest National Science Foundation (NSF) funded space weather CubeSat and is a collaboration between PolySat, Scientific Solutions Inc. (SSI), the University of Wisconsin, NASA Goddard and SRI International. The 3U will carry a mass spectrometer sensor suite, EXOS, in to low earth orbit (LEO) to measure neutral and ionized particles in the exosphere and thermosphere. Measurements of neutral and ion particles are directly impacted by the angle at which they enter EXOS and which leads to pointing requirements. A combination of a gravity gradient system with a momentum bias wheel is proposed to meet pointing requirements while …

Ad-Hoc Regional Coverage Constellations Of Cubesats Using Secondary Launches, Guy G. Zohar

Master's Theses

As development of CubeSat based architectures increase, methods of deploying constellations of CubeSats are required to increase functionality of future systems. Given their low cost and quickly increasing launch opportunities, large numbers of CubeSats can easily be developed and deployed in orbit. However, as secondary payloads, CubeSats are severely limited in their options for deployment into appropriate constellation geometries.

This thesis examines the current methods for deploying cubes and proposes new and efficient geometries using secondary launch opportunities. Due to the current deployment hardware architecture, only the use of different launch opportunities, deployment direction, and deployment timing for individual cubes …

Design And Performance Of Circulation Control Geometries, Rory Martin Golden

Master's Theses

With the pursuit of more advanced and environmentally-friendly technologies of today’s society, the airline industry has been pushed further to investigate solutions that will reduce airport noise and congestion, cut down on emissions, and improve the overall performance of aircraft. These items directly influence airport size (runway length), flight patterns in the community surrounding the airport, cruise speed, and many other aircraft design considerations which are setting the requirements for next generation aircraft. Leading the research in this movement is NASA, which has set specific goals for the next generation regional airliners and has categorized the designs that meet the …

Investigation Of Astm E 238 Bearing Pin Properties For Various Aerospace Alloys, Trevor J. Lee

Master's Theses

Aircraft are often designed with numbers determined by testing in a lab, rather than by repeatedly building prototypes. These lab tests conform to testing specifications so that the numbers can be compared between manufacturers, suppliers, and lab technicians. One such specification is ASTM specification E238 – 84(08), and it is used to determine important properties of a bearing pin joint like hinges, bolt holes, and rivet joints. The properties determined from this fastener-through-plate method are bearing strength, bearing yield strength, and bearing stiffness.

Adhering to the methods outlined in ASTM E238, a study was performed, looking at the effects that …

The Effect Of Sensor Mass, Sensor Location, And Delamination Location Of Different Composite Structures Under Dynamic Loading, Albert Darien Liu

Master's Theses

This study investigated the effect of sensor mass, sensor location, and delamination location of different composite structures under dynamic loading. The study pertains to research of the use of accelerometers and dynamic response as a cost-effective and reliable method of structural health monitoring in composite structures. The composite structures in this research included carbon fiber plates, carbon fiber-foam sandwich panels, and carbon-fiber honeycomb sandwich panels. The composite structures were manufactured with the use of a Tetrahedron MTP-8 heat press. All work was conducted in the Cal Poly Aerospace Structures/Composites Laboratory. Initial delaminations were placed at several locations along the specimen, …

Distributed Forcing On A 3d Bluff Body With A Blunt Base, An Experimental Active Drag Control Approach, Ethan Bruce Erlhoff

Master's Theses

This paper seeks to explore the effects of an active drag control method known as distributed forcing on a 3D bluff body with a blunt base. The 9.5 x 15.25 x 3 inch aluminum model constructed for this experiment has an elliptically shaped nose and rectangular aft section. The model is fitted with four, 12 Volt fans, forcing the freestream air into and out of 1 mm thick slots on the upper and lower trailing edges. The forcing is steady in time, held at a constant forcing velocity though all Reynolds numbers, but varies roughly sinusoidally in the spanwise direction …

Space Vehicle Testing, Charlotte Ann Belsick

Master's Theses

Requirement verification and validation is a critical component of building and delivering space vehicles with testing as the preferred method. This Master’s Project presents the space vehicle test process from planning through test design and execution. It starts with an overview of the requirements, validation, and verification. The four different verification methods are explained including examples as to what can go wrong if the verification is done incorrectly. Since the focus of this project is on test, test verification is emphasized. The philosophy behind testing, including the “why” and the methods, is presented. The different levels of testing, the test …

The Application Of Systems Engineering Principles To Model Lithium Ion Battery Voltage, George Gibbs

Master's Theses

The objective of this project is to present a Lithium Ion battery voltage model derived using systems engineering principles. This paper will describe the details of the model and the implementation of the model in practical use in a power system. Additionally, the model code is described and results of the model output are compared to battery cell test data. Finally, recommendations for increased model fidelity and capability are summarized.

The modeling theory has been previously documented in the literature but detailed implementation and application of the modeling theory is shown. The detailed battery cell test voltage profiles are proprietary; …

Confined Mixing Of Multiple Transverse Jets, Allen J. Bishop

Master's Theses

The mixing performance of multiple transverse jets has been evaluated experimentally. Measurement techniques included laser Doppler velocimetry and planar laser induced fluorescence. Basic findings are consistent with results presented in literature for single jet mixing behavior. Mixing performance has been compared to literature for the single jet case and the Holdeman parameter has been re-evaluated for effectiveness at low jet numbers. A single jet in a confined crossflow was found to have a local minimum at B(d⁄D) = 0.721. Results for two jets indicate monotonically decreasing unmixedness for the range of conditions tested, with no local optimum apparent. Data for …

Effects Of Seawater On The Mechanical Behavior Of Composite Sandwich Panels Under Monotonic Shear Loading, Thomas Robert Woo

Master's Theses

Abstract

Salt water environments are very harsh on materials that are used within them. Many issues are caused by either corrosion and/or internal degradation to the materials themselves. Composites are better suited for this environment due to their high strength to weight ratios and their corrosion resistance, but very little is known about the fracture mechanics of composites. The goal of this study is to gain a better understanding for the behavior of a composite boat hull under a shear loading, similar to the force water applies on the hull as the boat moves through the water; then attempt to …

Calibration And Characterization Of Cubesat Magnetic Sensors Using A Helmholtz Cage, Justin Dean Foley

Master's Theses

Small satellites, and CubeSats in particular, have quickly become a hot topic in the aerospace industry. Attitude determination is currently one of the most intense areas of development for these miniaturized systems and future Cal Poly satellite missions will depend heavily on magnetometers. In order to utilize magnetometers as a viable source of attitude knowledge, precise calibration is required to ensure the greatest accuracy achievable. This paper outlines a procedure for calibrating and testing magnetometers on the next generation of Cal Poly CubeSates, utilizing a Helmholtz cage to simulate any desired orbital magnetic field that would be experienced by a …

Determination Of Human Powered Helicopter Stability Characteristics Using Multi-Body System Simulation Techniques, Sean M. Brown

Master's Theses

Multi-Body System Simulation combined with System Identification was developed as a method for determining the stability characteristics of a human powered helicopter(HPH) configurations. HPH stability remains a key component for meeting competition requirements, but has not been properly treated. Traditional helicopter dynamic analysis is not suited to the HPH due to its low rotation speeds and light weight. Multi-Body System Simulation is able to generate dynamic response data for any HPH configuration. System identification and linear stability theory are used to determine the stability characteristics from the dynamic response. This thesis focuses on the method development and doesn't present any …