Aerospace Engineering Commons^™

Machine Learning To Predict Warhead Fragmentation In-Flight Behavior From Static Data, Katharine Larsen

Doctoral Dissertations and Master's Theses

Accurate characterization of fragment fly-out properties from high-speed warhead detonations is essential for estimation of collateral damage and lethality for a given weapon. Real warhead dynamic detonation tests are rare, costly, and often unrealizable with current technology, leaving fragmentation experiments limited to static arena tests and numerical simulations. Stereoscopic imaging techniques can now provide static arena tests with time-dependent tracks of individual fragments, each with characteristics such as fragment IDs and their respective position vector. Simulation methods can account for the dynamic case but can exclude relevant dynamics experienced in real-life warhead detonations. This research leverages machine learning methodologies to …

Passive, Self-Healable, Dielectric Elastomers For Structural Health Monitoring, Nicholas Smith

Doctoral Dissertations and Master's Theses

NASA maintains the ability to track a large majority of objects in Earth’s orbit, however lack the ability to track objects smaller than five centimeters in diameter. These untrackable objects represent a significant danger to inflatable structures. This work seeks to synthesize and fabricate a self-healable, passive, dielectric elastomer impact sensor for structural health monitoring on inflatable space structures subject to impact by micrometeoroids and orbital debris. In a setting in which impact repairs can be extremely costly, the implementation of such a technology would not only alert personnel of such an event but would also serve to decrease the …

Assessment Of Iso-Ahola’S Theory Of Tourism Motivation On Willingness To Fly As A Point-To-Point Suborbital Space Tourist, Brian T. Musselman

Doctoral Dissertations and Master's Theses

Suborbital space tourism involves flight in an air vehicle to an altitude exceeding 100 kilometers (62 miles). This altitude is referred to as the Karman Line and the edge of space. Point-to-point space travel is transportation in an air vehicle where the vehicle flies around the earth in space to decrease the time to travel from one point on the earth’s surface to another point on the earth’s surface. The commercial space flight industry has a vision for point-to-point space travel.

The study aimed to assess the influence of the four dimensions of Iso-Ahola’s (1982) theory of tourism motivation on …

A Data Driven Modeling Approach For Store Distributed Load And Trajectory Prediction, Nicholas Peters

Doctoral Dissertations and Master's Theses

The task of achieving successful store separation from aircraft and spacecraft has historically been and continues to be, a critical issue for the aerospace industry. Whether it be from store-on-store wake interactions, store-parent body interactions or free stream turbulence, a failed case of store separation poses a serious risk to aircraft operators. Cases of failed store separation do not simply imply missing an intended target, but also bring the risk of collision with, and destruction of, the parent body vehicle. Given this risk, numerous well-tested procedures have been developed to help analyze store separation within the safe confines of wind …

Behavioral Intention Factors For Prescription Deliveries By Small Unmanned Aircraft In Rural Communities, Sarah M. Talley

Doctoral Dissertations and Master's Theses

Nearly half of the U.S. population regularly use and depend on prescription medications; however, pharmacy availability and access to pharmacy services are often lacking, particularly in rural communities. In an effort to meet local healthcare needs, delivery by sUAS is proposed to ensure the nearly 60 million rural residents have access to their prescription medications.

As an emerging technology with little research into home delivery applications, the successful implementation of sUAS for prescription medication delivery requires public acceptance and positive behavioral intention toward its use. At the time of the current research, no prior studies have specifically focused on the …

Experimental Characterization Of Additively Manufactured Multi-Feather Wingtip Devices, Patricio Garzon

Doctoral Dissertations and Master's Theses

Soaring birds have evolved to fly for long periods of time without flapping their wings. Inspired by the flight of these birds, the proposed thesis presents an experimental investigation focused on wingtip devices designed based on biomimicry. The overarching engineering objective was to reduce the induced drag as a means to improve the fuel efficiency via these experimental wingtips. An associated secondary objective was to establish a method for manufacturing complex structures suitable for wing tunnel testing. A manufacturing technique that involved using composite weaves to reinforce additively manufactured structures was developed. This technique has the potential to reduce manufacturing …

Effect Of Spray Rails On Takeoff Performance Of Amphibian Aircraft, Soham Bahulekar

Doctoral Dissertations and Master's Theses

Amphibian aircraft have seen a rise in popularity in the recreational and utility sectors due to their ability to take off and land on both land and water, thus serving a myriad of purposes such as aerobatics, surveillance, and firefighting. The design of such seaplanes requires to be both aerodynamically and hydrodynamically efficient, especially during the takeoff phase. In the past, naval architects have implemented ways to make boats, yachts, and large ships more efficient; one of them being the addition of chine strips and spray rails on the hull. This thesis study explores the possibility of implementing spray rails …

Synthetic Gecko Inspired Dry Adhesive Through Two-Photon Polymerization For Space Applications, Zefu Ren

Doctoral Dissertations and Master's Theses

This work aims to develop an advanced and cost-effective fabrication process to produce a simplified gecko-inspired microstructure with two-photon polymerization and polymer molding, aimed to improve the adhesive properties of microstructures. Such adhesive microstructures can be implemented for multi-purpose adhesive grasping devices, which have recently gained significant interest in the space exploration sector. Previous gecko-inspired microstructures were reviewed, and the new gecko-inspired microstructures have been developed with the adaptation of additive manufacturing methods for facile fabrication. The examined microstructures in this thesis were the tilted mushroom-shaped and wedge-shaped designs, which could both maximize adhesion by shearing the micropillars toward the …

Optimization Of Rover Wheel Geometries For Planetary Missions, Nikita Amberkar

Doctoral Dissertations and Master's Theses

Rovers have been launched into space for exploration of the Moon and Mars to collect samples of rock and soil. To continue the explorations, the rovers need to have reliable wheels to drive around. However, due to the soil being soft, the wheels on the rover start to lose traction and the wheels sink while driving to various locations. Previous work in this field has been done experimentally or with the use of simulations. Only a few references report the effect of uncertainties in grouser simulation on the traction efficiency. The objective of this work was to (a) Understand the …

Quasi-Static Structural Analysis Of An Experimental Aircraft Wing, Scott Bender

Doctoral Dissertations and Master's Theses

In this report, a quasi-static load analysis is conducted on an experimental light sport aircraft wing via a whiffletree bending test. This report will discuss the loads present on the aircraft during straight level flight at a speed of 82 knots equivalent air speed. Flight load calculations are described along with the design of the whiffletree and mounting structures utilized for applying the distributed point loads. Initial finite element analysis is performed on the wing structure to determine critical strain locations and optimal sensor distribution. Subsequent mechanical experimentations are performed using a bending test to measure the strain at critical …

A Patient Risk Minimization Model For Post-Disaster Medical Delivery Using Unmanned Aircraft Systems, Mark J. Simpson

Doctoral Dissertations and Master's Theses

The purpose of this research was to develop a novel routing model for delivery of medical supplies using unmanned aircraft systems, improving existing vehicle routing models by using patient risk as the primary minimization variable.

The vehicle routing problem is a subset of operational research that utilizes mathematical models to identify the most efficient route between sets of points. Routing studies using unmanned aircraft systems frequently minimize time, distance, or cost as the primary objective and are powerful decision-making tools for routine delivery operations. However, the fields of emergency triage and disaster response are focused on identifying patient injury severity …

Vertical Take-Off And Landing Control Via Dual-Quaternions And Sliding Mode, Joshua Sonderegger

Doctoral Dissertations and Master's Theses

The landing and reusability of space vehicles is one of the driving forces into renewed interest in space utilization. For missions to planetary surfaces, this soft landing has been most commonly accomplished with parachutes. However, in spite of their simplicity, they are susceptible to parachute drift. This parachute drift makes it very difficult to predict where the vehicle will land, especially in a dense and windy atmosphere such as Earth. Instead, recent focus has been put into developing a powered landing through gimbaled thrust. This gimbaled thrust output is dependent on robust path planning and controls algorithms. Being able to …

Online Pilot Model Parameter Estimation For Loss-Of-Control Prevention In Aircraft Systems, Frederick Schill

Doctoral Dissertations and Master's Theses

A pilot is a highly nonlinear and incredibly complex controller whose responses are difficult to predict. Many accidents have occurred from pilot error before or after failures and almost always after entering areas of the flight envelope considered as Loss-of-Control regimes. If a pilot's inputs to the flight control system can be predicted, then the introduction of dangerous flight conditions can be readily avoided. Avoidance could take the form of a warning indicator or augmentation of the pilot's inputs. The primary difficulty lies in how to actually predict how the pilot will perform in the future.

Methods to solve this …

Dynamic Analysis Of Cubesat Impact On Lunar Surface, Dalton C. Korczyk

Doctoral Dissertations and Master's Theses

EagleCam is a pico-satellite (CubeSat) with dimensions of 100 x 100 x 150 mm3 that is going to the moon as a payload of the Intuitive Machines Nova-C lunar lander. The CubeSat’s purpose is to record the lunar landing from a 3rd person view. Unlike other CubeSats, EagleCam is designed to impact the lunar surface and there is no history to build off of. Specifically, EagleCam will need to survive a 30 m drop onto the lunar surface with all internal components fully operational post impact. This thesis is focused on the analytical, numerical, and experimental methods for determining the …

Controller Design For A Swirl Injection Hybrid Launch Vehicle, Ryan Kinzie

Doctoral Dissertations and Master's Theses

This research is focused on the design of controllers for stabilizing a launch vehicle with an internally originating torque. The motivation for this research arises from the new development of rocket engines which swirl combustion gases to gain combustion stability benefits, and in the case of hybrid rocket engines, fuel regression benefits as well. The stability of the launch vehicle dynamics due to the internal torque has not been discussed before. To the author’s knowledge, this is the first research to address the stabilization problem of the launch vehicle with internal torque. Due to the new design/characteristics of these engines, …

Time-Resolved Piv Measurements Of Ship Airwakes With Quartering Winds, Kaijus H. Palm

Doctoral Dissertations and Master's Theses

The unsteady, three-dimensional, turbulent airwake over the Simple Frigate Ship No. 2 (SFS2) with quartering wind flow directions was studied in a low-speed wind tunnel facility. Surface oil flow visualization and time-resolved stereoscopic and planar particle image velocimetry (PIV) measurements were made for three crosswise planes and a single centerline streamwise plane. Measurements included various configurations with the bow of the ship model at two different quartering wind conditions of 10 and 20 degrees, as well as cases with and without the effects of a simulated atmospheric boundary layer (ABL). A comparative analysis of the time-averaged flow structures between the …

Influence Of Wing Planform Shape On The Effectiveness Of A Fixed-Slot, Yuan Zhao

Doctoral Dissertations and Master's Theses

This thesis report explores the effect of the Clark-Y wing geometry on lift and drag to use as a reference during aircraft design stage. The different characteristics investigated are fixed slot span, taper ratio, washout, and sweep angle. Plain wings, half slotted wings, and fully slotted wings were built in CATIA with an aspect ratio of 6 and different taper ratio, washout, and sweep angles. Using the CATIA models to generate the 3-D grids in Pointwise. All the simulations were tested in Ansys-Fluent under sea-level conditions with a Reynold number of 609000. The relationships between the aerodynamic characteristics and the …

Stochastic Model Predictive Control Via Fixed Structure Policies, Elias Wilson

Doctoral Dissertations and Master's Theses

In this work, the model predictive control problem is extended to include not only open-loop control sequences but also state-feedback control laws by directly optimizing parameters of a control policy. Additionally, continuous cost functions are developed to allow training of the control policy in making discrete decisions, which is typically done with model-free learning algorithms. This general control policy encompasses a wide class of functions and allows the optimization to occur both online and offline while adding robustness to unmodelled dynamics and outside disturbances. General formulations regarding nonlinear discrete-time dynamics and abstract cost functions are formed for both deterministic and …

State-Of-The-Art Of Thermal Control Solutions To Establish A Modular, Multi-Orbit Capable Spacecraft Thermal Management System Design Methodology, Robert C. Consolo Jr

Doctoral Dissertations and Master's Theses

Today, the exploration and exploitation of space continues to become a more common occurrence. All types of spacecraft (S/C) utilize various types of thermal management solutions to mitigate the effects of thermal loading from the unforgiving vacuum of space. Without an appropriately designed thermal system, components on-board the S/C can experience failure or malfunction due to fluctuations in temperatures either beyond the designed operational parameters or unstable oscillating temperatures. The purpose of this study is to perform a comprehensive review of technologies available today that are being used for thermal management onboard S/C in addition to investigating the means to …

Numerical Simulation Of A Cryogenic Spray, Neel Kishorkumar Shah

Doctoral Dissertations and Master's Theses

Cryogenic sprays have many applications in modern engineering. Cooling of electronic equipment subject to high heat flows, surgical ablation of gastrointestinal mucosae or orbital maneuvering are a few examples of their versatility. However, the atomization of a cryogenic liquid is a complex process. During such an event, aerodynamic effects associated with secondary atomization are further affected by thermodynamic flashing. A better understanding of the characteristics of cryogenic sprays is then necessary to allow for improved design and optimization in applications. The overarching objective of this study is to document such characteristics. The numerical simulation was performed over cryogenic nitrogen spray …

In-Situ Monitoring Of Additive Manufacturing Using Digital Image Correlation, Martina Jani

Doctoral Dissertations and Master's Theses

Advances in additive manufacturing over the past decade have led to applications in multiple fields. In particular, additive manufacturing answers the need for high flexibility in designing complex structures, however, the rapid thermal fluctuations during processing lead to numerous defects and processing-induced residual stresses. In this research, an in-situ approach using Digital Image Correlation (DIC) is developed to monitor the deformation during the processing, and thereby analyze the formation of defects and residual stresses. DIC is a visual technique that compares the changes in speckle pattern in consecutive images of a specimen to determine the displacements and strains. This research …

Kinematics Of Inter-Ply Interfaces In Composite Manufacturing, Sandeep Chava

Doctoral Dissertations and Master's Theses

The ubiquitous usage of polymer matrix composites in many applications demands a comprehensive understanding of composite interfaces and processing induced residual stresses, which critically affect both the manufacturing processes and the deformation mechanisms. Processing induced residual stresses are often responsible for causing warping, delamination, and dimensional instability in composite structures. This research includes new in-situ experimental approaches, cure cycle design, interface modification, and thermomechanical modeling for developing a fundamental understanding of the cure kinetics during composite manufacturing. Strains, ply-movement, and formation of defects are observed in-situ using digital image correlation (DIC) during the autoclave cure cycle for the first time. …

Trajectory Generation For A Multibody Robotic System: Modern Methods Based On Product Of Exponentials, Aryslan Malik

Doctoral Dissertations and Master's Theses

This work presents several trajectory generation algorithms for multibody robotic systems based on the Product of Exponentials (PoE) formulation, also known as screw theory. A PoE formulation is first developed to model the kinematics and dynamics of a multibody robotic manipulator (Sawyer Robot) with 7 revolute joints and an end-effector.

In the first method, an Inverse Kinematics (IK) algorithm based on the Newton-Raphson iterative method is applied to generate constrained joint-space trajectories corresponding to straight-line and curvilinear motions of the end effector in Cartesian space with finite jerk. The second approach describes Constant Screw Axis (CSA) trajectories which are generated …

Airspace Integration Of New Entrants And Safety Risk Management Models, Fadjimata Issoufou Anaroua

Doctoral Dissertations and Master's Theses

In recent years, the demand for airspace access of Unmanned Aerial Systems (UAS) increased significantly and is continuously increasing for different altitude-types UAS. A similar evolution is expected from Commercial Space Operations (CSO) in the next years. These aviation/aerospace systems will need to be seamlessly integrated into the National Airspace System (NAS), at their operational altitude levels, and accounted for from all perspectives, including proactively addressing their safety hazards. This thesis captures the requirements for the new entrants’ integration, and then identifies and analyzes the safety risks added to the NAS operations by its new entrants, the future omnipresent UAS …

Fabrication & Mechanical Properties Of Hastelloy-X Matrix Ceramic Composite, Sultan Stewart

Doctoral Dissertations and Master's Theses

In the aerospace industry, there is a desire for increased thermal and mechanical properties of sealing materials. In this thesis, porous Hastelloy-X alloy scaffolds with 80% porosity, currently used for fabricating seals in turbine applications, were used as the base material. The microstructure of the porous Hastelloy-X scaffolds was infiltrated using a room temperature curing silicate colloid (trade name -Dichtol HTWG Hydro #2506) and a novel zirconia based colloid to fabricate the metal matrix composites. Various fabrication processes, some using vacuum and pressure to assist the flow were utilized to infiltrate the scaffolds. The green composites were then cured at …

Satellite Deceleration Using Gravity Assist From Asteroid, Nicolas M. Prulhiere

Doctoral Dissertations and Master's Theses

Satellites have used gravity assists to increase their speed when exploring the solar system. This same maneuver can be done but with the objective to slow down the satellites. This has been theorized to slow down asteroids using the moon to capture them in earth’s orbit. My goal is to determine if asteroids can be used to provide a change in speed great enough to the point that after multiple of these maneuvers the satellite can come to a stop. By being able to slow down and stop a satellite without having to use thrusters will allow the mass allocated …

High Fidelity Studies In Closed-Loop Control Of Unsteady Aerodynamics, Miriam Theobald-Deschine

Doctoral Dissertations and Master's Theses

We implement and explore the success of a nonlinear, closed loop flow control strategy based on POD-ROM focusing on boundary-layer transitional flow in high-fidelity computational studies involving FDL3DI ILES code. Controlling the boundary-layer transition from laminar to turbulent allows the laminar boundary-layer to be lengthened, decreasing skin-friction drag on an airfoil. Analyses are conducted on a flat plate with an elliptical leading edge, later to be implemented in future studies with real airfoil geometry. The feedback control design employs strategically placed synthetic-jet micro actuators and pressure sensors. The efficiency of the closed-loop flow control strategies is examined in comparison with …

The Effect Of Part Curvature On The Formation Of Residual Stresses In Carbon Fiber Prepreg Laminates, Bradley Rogan

Doctoral Dissertations and Master's Theses

The formation of residual stresses during the processing of composite parts can lead to undesired defects such as delamination which can reduce the overall strength of a completed component. Furthermore, the addition of curvature to the part geometry tends to result in wrinkle formation which leads to stress concentrations developing throughout the curing process in the areas near these wrinkles. In this work, Digital Image Correlation (DIC) will be used to monitor the development of stresses throughout the cure cycle of carbon fiber prepreg in several different lay-ups and across tool plates with varying curvatures to determine what effect the …

Optimal Sizing And Control Of Hybrid Rocket Vehicles, Srija Ryakam

Doctoral Dissertations and Master's Theses

In the present work, a genetic algorithm is used to optimize a hybrid rocket engine in order to minimize the propellant required for a specific mission. In a hybrid rocket engine, the mass flow rate of the oxidizer can be throttled to enhance the performance of the rocket. First, an analysis of the internal ballistics and the ascent trajectory has been carried out for different mass flow rates of the oxidizer as a function of time, for a fixed amount of oxidizer, in order to study the effect of throttling. Two equivalent problems are considered: in the first problem the …

Relative Pose Uncertainty Quantification Using Lie Group Variational Filtering, Christopher W. Hays

Doctoral Dissertations and Master's Theses

The applications of visual sensing techniques have revolutionized the way autonomous systems perceive their environment on Earth. In space, the challenge of accurate perception has proven to be a difficult task. Due to adverse lighting conditions, high-noise images are common and degrade the performance of traditional feature-based estimation and perception algorithms. This work explores the applications of a variational filtering scheme founded in Lie Group theory to an autonomous rendezvous, proximity operations and docking problem. Two methodologies, a Monte Carlo approach and an Unscented Transform, for propagating uncertainty using a Lie Group Variational Filter are introduced and developed.