Aerospace Engineering Commons^™

Increasing Participation In The Pilot Weather Reporting (Pirep) System Through User Interface Design, Stephen M. Casner

Journal of Aviation Technology and Engineering

Although pilots regard pilot weather reports (PIREPs) as valuable flight planning resources, the number of PIREPs that pilots submit is relatively small. In a previous survey, pilots indicated that submitting PIREPs sometimes requires too much effort, and that they are often unable to recall the information fields required to complete a report. Pilots also indicated that the idea of submitting a PIREP often does not occur to them, and that they feel that other pilots are mainly interested in receiving reports about severe weather. In this study the authors attempt to address obstacles to submitting PIREPs by proposing two alternative …

Validation Of New Technology Using Legacy Metrics: Examination Of Surf-Ia Alerting For Runway Incursion Incidents, Robert Joslin

Journal of Aviation Technology and Engineering

This study demonstrated an innovative method of utilizing expert raters and actual high-risk incidents to identify shortcomings of using legacy metrics to measure the effectiveness of new technology designed to mitigate hazardous incidents. Expert raters were used to validate the Enhanced Traffic Situational Awareness on the Airport Surface with Indications and Alerts (SURF-IA) model for providing alerts to pilots to reduce the occurrence of pilot deviation type runway incursion incidents categorized as serious (Category A or B) by the legacy FAA/ICAO Runway Incursion Severity Classification (RISC) model. The study concluded that the SURF-IA model did not yield an outcome of …

Dynamic Analysis Of Granular Battery Assembly, Rohan Dudaney, Waterloo Tsutsui, Weinong Chen

The Summer Undergraduate Research Fellowship (SURF) Symposium

Collisions and impacts are an inevitable reality when it comes to commercial cars and vehicles, but as batteries become more prevalent it is vital to understand how they react dynamically and as a system to better protect both the passengers and toxic chemicals inside of the batteries. One potential solution is to surround these batteries with non-vital tubes that can be sacrificed and help protect the batteries. This study is done to understand the structure of batteries and to test how an assembly of sacrificing cells and batteries reacts in an impact situation to see if there is significant energy …

Fiber Length And Orientation In Long Carbon Fiber Thermoplastic Composites, Imad Hanhan, Connor Sullivan, Bhisham Sharma, Michael Sangid

The Summer Undergraduate Research Fellowship (SURF) Symposium

Carbon fiber composites have become popular in aerospace applications because of their lightweight yet strong material properties. The injection molding process can be used to produce discontinuous fiber composites using less time and resources than traditional methods, thereby broadening carbon fiber composites’ applications in different industries. Utilization of longer fibers offers more load carrying capability and superior strength properties for injected molded composites. Since the fiber length and the orientation distribution in Long Fiber Thermoplastics (LFTs) directly affects LFT composites’ material properties, there is a need to study the microstructure of LFTs and characterize fiber length and orientation distributions. Therefore, …

Noise Source Analysis For Simulated Turbulent Jets, Robert W. Skidmore, Nitin S Dhamankar, Kurt M. Aikens, Gregory Blaisdell

The Summer Undergraduate Research Fellowship (SURF) Symposium

Large Eddy Simulation (LES) is an efficient computational approach to study turbulent flows and has seen increasing application to the study of jet noise. The main challenge of LES has been the realistic simulation of experiments at reasonable cost. Recent LES studies have been realistic enough to gain important insight into jet noise from the large amount of data generated. This study attempts to characterize the sources of noise from a turbulent jet via analysis of the LES results. Three different analysis tools are implemented. The first two are comparable to analyses used on experimental data: two-point cross-correlations between far-field …

Simulation Of Bio-Inspired Porous Battery Electrodes, Raju Gupta, R. Edwin Garcia, Rui Tu

The Summer Undergraduate Research Fellowship (SURF) Symposium

Advancement of technology has led to the increase in use of electronic devices. However, longer life of the rechargeable battery used in electronic devices is one of the biggest issue and demand in the world of electronic devices at present. Battery's performance is affected by the orientation, arrangement, shape and size, and porosity of the materials out of which battery electrodes are made. The goal of this project is to develop a set of numerical libraries that allow developing material micro structures that will allow increasing the performance of rechargeable batteries. We focused on the development of an algorithm that …

Dynamic Response Of Textile Material Under Transverse Impact, Yuchen Zheng, Matthew C. Hudspeth, Weinong W. Chen

The Summer Undergraduate Research Fellowship (SURF) Symposium

Textile materials, such as Dyneema and Kevlar, are the major raw materials for state of the art military or personal security armor vests. However, in impact experiments, actual observed penetration speed is much lower than theoretically predicted penetration speed. Each armor vest is composed of high performance yarns which are woven together to form fabrics, which when stacked together form a vest. Understanding penetration behavior of yarns is essential to evaluate the performance of fabric, which will be useful for the design of better vests. The project is composed of three parts: static experiments, dynamic yarn experiments and dynamic fabric …

Microthruster Fabrication And Characterization: In Search Of The Optimal Nozzle Geometry For Microscale Rocket Engines, Katherine L. Fowee, Alina Alexeenko

The Summer Undergraduate Research Fellowship (SURF) Symposium

A major consideration in microsatellite design is the engineering of micropropulsion systems that can deliver the required thrust efficiently with tight restrictions on space, weight, and power. Cold gas thrusters are one solution to the demand for smaller propulsion systems to accommodate the advancements in technology that have allowed for a reduction in the size and thus the cost of satellites. While much research has been done in understanding the flow regimes within these microthrusters, there is a need to understand how different nozzle designs affect microthruster performance. This requires that experimental data be collected on varying nozzles shapes (orifices, …

Development Of A Real Time Bistatic Radar Receiver Using Signals Of Opportunity, Nicholas Rainville

Open Access Theses

Passive bistatic radar remote sensing offers a novel method of monitoring the Earth's surface by observing reflected signals of opportunity. The Global Positioning System (GPS) has been used as a source of signals for these observations and the scattering properties of GPS signals from rough surfaces are well understood. Recent work has extended GPS signal reflection observations and scattering models to include communications signals such as XM radio signals. However the communication signal reflectometry experiments to date have relied on collecting raw, high data-rate signals which are then post-processed after the end of the experiment. This thesis describes the development …

A Small-Scale Experiment Using Microwave Interferometry To Investigate Detonation And Shock-To-Detonation Transition In Pressed Tatb, Peter John Renslow

Open Access Theses

A small-scale characterization test utilizing microwave interferometry was developed to dynamically measure detonation and run to detonation distance in explosives. The technique was demonstrated by conducting two experimental series on the well-characterized explosive triaminotrinitrobenzene (TATB). In the first experiment series, the detonation velocity was observed at varying porosity. The velocity during TATB detonation matched well with predictions made using CHEETAH and an empirical relation from the Los Alamos National Laboratory (LANL). The microwave interferometer also captured unsteady propagation of the reaction when a low density charge was near the failure diameter. In the second experiment series, Pop-plots were produced using …

Experimental Study Of Unsteady Heat Release In An Unstable Single Element Lean Direct Injection (Ldi) Gas Turbine Combustor, Varun S. Lakshmanan

Open Access Theses

In an effort to curb emissions from gas turbine engines, many low emission engine concepts have been developed. Among the most promising of these is the LDI (Lean Direct Injection). These systems operate at relatively low equivalence ratios close to blowout and are prone to instabilities. Combustion instabilities can reduce the life of the combustor by causing large pressure fluctuations and enhanced heat release to the walls of the combustor and reduce the efficiency of the engines. The understanding of combustion instabilities is vital to the implementation of such systems. Combustion instabilities are studied in an self-excited single element gas …

Assessment Of Noise Metrics For Application To Rotorcraft, Andrew L. Mcmullen

Open Access Theses

It is anticipated that the use of rotorcraft passenger vehicles for shorter journeys will increase because their use can reduce the time between boarding and take-off. The characteristics of rotorcraft noise are very different to that of fixed wing aircraft. There can be strong tonal components, fluctuations that can also make the noise sound impulsive, and future rotorcraft may produce proportionally more low frequency noise content. Most metrics that are used today to predict noise impact on communities around airports (e.g., L_dn) are just functions of A-weighted sound pressure level. To build a better noise annoyance model that …

Impinging Jet Spray Formation Using Non-Newtonian Liquids, Neil S. Rodrigues

Open Access Theses

Over the past two decades there has been a heightened interest in implementing gelled propellants for rocket propulsion, especially for hypergolic bi-propellants such as monomethylhydrazine (MMH) and nitrogen tetroxide oxidizer (NTO). Due to the very high level of toxicity of hypergolic liquid rocket propellants, increasing safety is an important area of need for continued space exploration and defense operations. Gelled propellants provide an attractive solution to meeting the requirements for safety, while also potentially improving performance. ^ A gelling agent can be added to liquid propellants exhibiting Newtonian behavior to transform the liquid into a non-Newtonian fluid with some solid-like …

A Study To Estimate And Compare The Total Particulate Matter Emission Indices (Ein) Between Traditional Jet Fuel And Two Blends Of Jet A/Camelina Biofuel Used In A High By-Pass Turbofan Engine: A Case Study Of Honeywell Tfe-109 Engine, Jacob Joshua Howard Shila

Open Access Theses

The aviation industry is expected to grow at an annual rate of 5% until the year 2031 according to Boeing Outlook Report of 2012. Although the aerospace manufacturers have introduced new aircraft and engines technologies to reduce the emissions generated by aircraft engines, about 15% of all aircraft in 2032 will be using the older technologies. Therefore, agencies such as the National Aeronautics and Astronautics Administration (NASA), Federal Aviation Administration (FAA), the Environmental Protection Agency (EPA) among others together with some academic institutions have been working to characterize both physical and chemical characteristics of the aircraft particulate matter emissions to …

Catalysts For Portable, Solid State Hydrogen Genration Systems, Jason Robert Gabl

Open Access Theses

Hydrogen and air powered proton exchange membrane fuel cells are a potential alternative to batteries. In portable power systems, the design requirements often focus on cost efficiency, energy density, storability, as well as safety. Ammonia borane (AB), a chemical hydride containing 19.6 wt. % hydrogen, has a high hydrogen capacity and is a stable and non-toxic candidate for storing hydrogen in portable systems.

Throughout this work, Department of Energy guidelines for low power portable hydrogen power systems were used as a baseline and comparison with commercially available systems. In order to make this comparison, the system parameters of a system …

Numerical Simulation Of Hydrogen Plasma In Mpcvd Reactor, Di Huang

Open Access Theses

A numerical study was conducted to build a model able to estimate the plasma properties under different working conditions for pure hydrogen plasma in a MPCVD reactor. A plasma model based on standing wave assumption and a linear estimation of ne and coupled the EM simulation, heat transfer simulation and UDF calculations of plasma properties was built in COMSOL Muitiphysics and tested with six different working conditions. The reliability of COMSOL EM solver was tested through comparing the simulation results with a benchmark EM solver, ANSYS HFSS. The validities of two assumptions made about the electrical field, standing wave assumption …

"Cap" Cornish, Indiana Pilot: Navigating The Century Of Flight, Ruth Ann Ingraham

Purdue University Press Books

Clarence "Cap" Cornish was an Indiana pilot whose life spanned all but five years of the Century of Flight. Born in Canada in 1898, Cornish grew up in Fort Wayne, Indiana. He began flying at the age of nineteen, piloting a "Jenny" aircraft during World War I, and continued to fly for the next seventy-eight years. In 1995, at the age of ninety-seven, he was recognized by Guinness World Records as the world's oldest actively flying pilot. The mid-1920s to the mid-1950s were Cornish's most active years in aviation. During that period, sod runways gave way to asphalt and concrete; …

Effect Of Cellular Phone And Radar Forensics On Search And Rescue Duration For General Aviation Aircraft Accidents In The Contiguous United States, Ryan J. Wallace

Journal of Aviation Technology and Engineering

Emergency Locator Transmitters (ELT) are generally the primary tool for locating distressed aircrews following an aircraft accident. In 2009, the International COSPAS-SARSAT organization ordered the cessation of 121.5 MHz ELT satellite monitoring to alleviate systemic false alarms and encourage pilots to upgrade ELTs to modern 406 MHz models. While most nations acquiesced to the mandate, the United States encountered severe resistance from pilot groups. As a result, 121.5 MHz ELTs are still in use in the U.S. but remain unmonitored by satellite systems. This study sought to assess the impact of alternative search methods such as radar and cellular phone …

Multi-Injector Modeling Of Transverse Combustion Instability Experiments, Kevin "James " Shipley

Open Access Theses

Concurrent simulations and experiments are used to study combustion instabilities in a multiple injector element combustion chamber. The experiments employ a linear array of seven coaxial injector elements positioned atop a rectangular chamber. Different levels of instability are driven in the combustor by varying the operating and geometry parameters of the outer driving injector elements located near the chamber end-walls. The objectives of the study are to apply a reduced three-injector model to generate a computational test bed for the evaluation of injector response to transverse instability, to apply a full seven-injector model to investigate the inter-element coupling between injectors …

Experimental Investigation Of A Forced Response Condition In A Multistage Compressor, William Louis Murray

Open Access Theses

The objective of this research is twofold. Firstly, the design, development, and construction of a test facility for a Honeywell APU-style centrifugal compressor was implemented, as well as the design and construction of an inlet flow experiment. Secondly, the aeromechanical response of an embedded stage in the Purdue 3-Stage axial research compressor was analyzed through a suite of different measurement techniques in the fulfillment of the end of the GUIde IV Consortium contract. ^ The purpose of the first phase of Honeywell work was to comprehensively measure the flow field of an APU-style centrifugal compressor inlet through the use of …

Unsteady Forces On A Spherical Particle Accelerating Or Decelerating In An Initially Stagnant Fluid, Yashas Mudlapur Phaneesh Keshav

Open Access Theses

Flows with particles play an important role in a number of engineering applications. These include trajectories of droplets in sprays in fuel-injected-reciprocating-piston and gas-turbine engines, erosion of materials due to particle impact on a surface, and deposition of materials on surfaces by impinging droplets or particles that could solidify or bond on impact. For these applications, it is important to understand the forces that act on the particles so that their trajectories could be predicted.

Considerable work has been done on understanding the forces acting on spherical particles, where the Reynolds numbers (Rep ) based on the particle …

Investigating Surface Performance Trade-Offs Of Unimpeded Taxiways, Tiffany T. Le

Open Access Theses

Optimizing usage of unimpeded taxiways is a near-term operational change to mitigate emission impact on aviation and increase efficiency at airports. An unimpeded taxiway is a path for an aircraft to taxi around an active runway. Unimpeded taxiways provide benefits such as increased departure throughput, increased safety, reduced surface congestion, more efficient taxi-in procedures, and thereby also yield environmental benefits. The goals of this work are to investigate the use of current taxiways, examine surface performance and fuel burn trade-offs, and to develop a decision-support model based on potential fuel savings of unimpeded taxiways. This study analyzes unimpeded taxiway use …

Detecting Air Traffic Controller Interventions In Recorded Air Transportation System Data, Yul Kwon

Open Access Theses

In this study, I propose a systematic method of detecting aircraft deviation due to air traffic controller (ATC) intervention. The aircraft deviations associated with ATC interventions are detected using a heuristic algorithm developed from analyzing the actual positions of an aircraft to its filed flight plan when the aircraft trajectories were identified as having an encounter in a loss-of-separation incident. An actual (closed-loop) flight trajectory of the Cleveland Air Route Traffic Control Center (ZOB ARTCC) was collected from the FlightAware database. This was compared with the corresponding planned (open-loop) trajectory dataset generated by the Microsoft© Flight Simulator X (FSX). I …

Experimental And Numerical Study Of The Air Distribution In An Airliner Cabin, Wei Liu

Open Access Theses

Nowadays, more people, including those with impaired health or who are otherwise potentially sensitive to the cabin environment, are traveling by air than ever before. The flying public demands a higher comfort level and a cleaner environment because they encounter a combination of environmental factors including low humidity, low air pressure, and sometimes, exposure to air contaminants such as ozone, carbon monoxide, various organic chemicals, and biological agents. Moreover, international air travel has increased the potential risks associated with airborne disease transmission and the release, whether accidentally or intentionally, of noxious substances during flight. Many studies suggest that the risk …

Effects Of Crossflow In An Internal-Cooling Channel On Film Cooling Of A Flat Plate Through Compound-Angle Holes, Zachary Taylor Stratton

Open Access Theses

The film-cooling holes in turbine blades are fed from an internal cooling channel. This channel imposes a crossflow at the entrance of the holes that can significantly affect the performance of the cooling jets that emanate from those holes. In this study, CFD simulations based on steady RANS with the shear-stress transport (SST) and the realizable k -ε turbulence models were performed to study film cooling of a flat plate with cooling jets issuing from eight round holes with a compound angle of 45 degrees, where the coolant channel that fed the cooling jets was oriented perpendicular to the direction …

Biaxial Shear/Tension Failure Criteria Of Spectra Single Fibers, Jianzhuo Sun

Open Access Theses

An experimental study was conducted to develop the biaxial failure surface criteria of single Spectra 130d and 100d filaments in a torsion-tension environment. The cross-sectional profiles of single Spectra fibers were investigated using scanning electron microscopy and X-ray computed tomography. A pin-gripping method to fix the ends of a polyethylene single fiber was developed. Effects of pin diameter on failure stress for both Spectra 130d and 100d were characterized. It was found that the perturbed stress field effect can be neglected when the pin diameter is larger than 0.8 mm. Additionally, the effect of the sample's gage length on fiber …

Feasibility Analysis Of Large Length-Scale Thermocapillary Flow Experiment For The International Space Station, Samantha Jean Alberts

Open Access Theses

The investigation of microgravity fluid dynamics emerged out of necessity with the advent of space exploration. In particular, capillary research took a leap forward in the 1960s with regards to liquid settling and interfacial dynamics. Due to inherent temperature variations in large spacecraft liquid systems, such as fuel tanks, forces develop on gas-liquid interfaces which induce thermocapillary flows. To date, thermocapillary flows have been studied in small, idealized research geometries usually under terrestrial conditions. The 1 to 3m lengths in current and future large tanks and hardware are designed based on hardware rather than research, which leaves spaceflight systems designers …

Blast Energy Mitigation In Porous Rocks, Brittany Corinne Essink

Open Access Theses

Geo-materials are commonly used and sought after for blast mitigation applications due to their wide availability and low cost compared to industry trademarked materials. Characterization of these natural geo-materials such as volcanic rocks is of paramount importance in determining their blast mitigation capabilities. While there is a large amount of information available for materials such as concrete or sand blasts, information on the properties of volcanic rocks is far more scarce. This lack of data is due to the wide range of existing natural volcanic rocks and the variation in the minerals and pore structures of the rocks.

In this …

Post-Fracture Capacity Of Railroad Flat Car Bridges, Teresa L. Washeleski

Purdue Road School

Railroad flatcars (RRFCs) are a convenient option to replace existing deteriorating bridge structures on low-volume roads. They are typically used as the bridge superstructure by placing two or more flatcars side-by-side to achieve the desired bridge width. Utilizing RRFCs as a bridge allows for rapid construction and greater cost savings compared to traditional practices. These benefits make them an attractive solution for rural communities in Indiana, as well as other states.

Uncertainty remains about the response under higher loads than could be easily achieved in the field and the level of redundancy of railroad flatcar bridges. Using RRFCs as bridges …

Post-Failure Capacity Of Built-Up Steel Members, Matthew H. Hebdon

Purdue Road School

Mechanically fastened built-up steel members have long been known to possess internal member redundancy and, as a result, multiple load paths which can be exploited to increase their functional life. Internal redundancy provides the ability to resist total member failure in the event of a fracture of an individual component. However, there is little experimental data in the literature regarding post-fracture capacity in terms of strength and subsequent fatigue life. The experimental study currently underway will provide needed information on parameters that affect the ability of built- up members to arrest a fracture as well as the available remaining fatigue …