Aerospace Engineering Commons^™

Study Of Hybrid Magneto-Active Propellant Management Device For Slosh Damping, Leander Paul

Doctoral Dissertations and Master's Theses

Sloshing of liquid upon the application of an external force is a natural phenomenon as the free surface is allowed to move without any constraints. Study of slosh is an ongoing research for many decades and many novel inventions in Propellant Management Devices (PMDs) such as the rigid baffles and elastomeric membranes have been implemented to counteract the free surface effect in both passive and active membrane known as Magneto-Active Propellant Management Device (MAPMD) to actively control the free surface effect and reduce fuel slosh is explored in this research. Being a hybrid membrane, it would initially offer passive resistance …

2d Aeroacoustic Analysis Of Flow In The Flame Trench, Meghan Pokorski

Doctoral Dissertations and Master's Theses

We present here a methodology for using the commercial software ANSYSFLUENT to predict the acoustic field associated with Space-Launch System (SLS). We consider a two-dimensional model of flame deflector, and flame trench. The ANSYS code is then used to simulate the internal flow. Both the steady state case is considered along with other cases where the inflow has a harmonic component. A Ffowcs-Williams Hawking (FWH) surface is then constructed within the computational domain to use the computed flow fluctuations to obtain the acoustic field. The acoustic data was then compared to the experimental data.

When using the ANSYS code for …

Analysis Of A Coupled Micro- And Triple-Impingement Cooling Configuration In The C3x Vane, Chase D. Rossman

Doctoral Dissertations and Master's Theses

This study attempts to improve the trailing edge protection of a turbine vane by incorporating two concepts from the literature. These two concepts are optimized near wall cooling passages and a triple-impingement configuration in the vane trailing edge. Finally this study explores a CFD conjugate analysis based on the Shear Stress Transport k(l) turbulence model. The overall goal is to produce a more effective cooling configuration by studying the effects of the flow and heat transfer of the dual configuration, while keeping the integrity of the turbine vane. Star-CCM+ was utilized to carry out the computational data on a 3-D …

Prediction Of Tonal Acoustic Radiation Due To Feedback-Loop Resonant Interactions In Transitional Airfoils, Seyyed Saman Salehian

Doctoral Dissertations and Master's Theses

The objective to this work is to employ the surface integral methods to study the far-field noise propagation from the flow acoustic resonant interactions of the transitional airfoil. The Potential-Theoretic Method (PTM) as an advancement to traditional Kirchhoff methods is presented. The PTM eliminated the need to calculate the normal derivatives of pressure and an arbitrary Kirchhoff surface can be employed. The numerical procedure to implement the PTM is fairly simple. The formulation and physical assumptions of the approach is reviewed, and the numerical procedure is implemented. Furthermore, the two dimensional formulation of the Ffowcs Williams - Hawkings (FW-H) equation …

Investigation Of Pin Fin Cooling Channels For Applications In Gas Turbines, Royce Fernandes

Doctoral Dissertations and Master's Theses

Gas turbine blades are often cooled using internal cooling channels to prevent failure at temperatures beyond material limitations. Pin fin channels are commonly used on the trailing edge of the blades, where they enhance heat transfer and also provide structural support. This study focuses on the validation of several commercially available RANS turbulence models in CFD, that are used to computationally simulate the flow features inside a pin fin cooling channel. Turbulence models investigates are: Menter’s kω SST, realizable k-ε, and a quadratic formulation of the realizable k-ε model. The geometry investigated is a staggered 8 row pin fin channel. …

The Effect Of Axial Spacing Of Constant And Variable Blockages On The Deflagration-To-Detonation Transition In A Pulse Detonation Engine, Nicole Gagnon

Doctoral Dissertations and Master's Theses

An investigation was conducted into the effects of obstacle spacing on the deflagration-to-detonation transition section length in a pulse detonation engine. Testing was conducted with one hundred and ninety-five different obstacle, and spacing configurations. The configurations included constant, as well as variable spacing between obstacles. The goal of this investigation was to correlate the spacing between obstacles and the blockage ratio of the obstacles with the detonation success and the shortening of the DDT section. The ten cases that achieved the highest percentage of detonations were investigated further to determine the distance needed for the deflagration-to-detonation transition. A 33% blockage …

Optical Tracking And Spectral Characterization Of Cubesats For Operational Missions, Forrest Gasdia

Doctoral Dissertations and Master's Theses

Orbital debris in low Earth orbit is of growing concern to operational satellites from the government and commercial sector. With an uptick in worldwide satellite launches and the growing adoption of the CubeSat standard, the number of small objects in orbit are increasing at a faster pace than ever. As a result, a cascading collision event seems inevitable in the near future.

The United States Strategic Command tracks and determines the orbit of resident space objects using a worldwide network of radar and optical sensors. However, in order to better protect space assets, there has been increased interest in not …

Vibration Analysis Of A Composite Wing Box With Arbitrarily Shaped Spars And Ribs, Rossana R. Fernandes

Doctoral Dissertations and Master's Theses

In this research, the free vibration analysis of composite wing boxes with curvilinear spars and ribs is performed. Modern manufacturing technologies, such as Electron Beam Freeform Fabrication and Friction Stir Welding, have allowed the manufacturing of arbitrarily shaped stiffeners. Curvilinear stiffeners provide flexibility in design as they can assume an infinite number of paths. Curvilinear spars and ribs can in some instances provide a better vibration and static response than their straight counterparts while reducing the overall mass of the structure. An equivalent continuum plate model of a wing box using energy formulations is proposed at the preliminary design stage …

Magneto-Rheological Fluid Device As Artificial Feel Force System On Aircraft Control Stick, Vignesh Manoharan

Doctoral Dissertations and Master's Theses

The conventional feel system in any aircraft occupies large space in the cockpit and has complicated designs. The primary objective of this research is to develop an artificial feel force system that can overcome some drawbacks of the current feel force system. A novel feel system using magneto-rheological (MR) fluid is constructed to precisely control the shear stress under the magnetic field. To validate the functionality of the MR artificial feel system, the final system is fabricated and multiple tests are performed to acquire force-velocity characteristics that are compared to the mathematical model derived. In addition, the reference model of …

Software Defined Multi-Spectral Imaging For Arctic Sensor Networks, Sam B. Siewert, Matthew Demi Vis, Ryan Claus, Vivek Angoth, Karthikeyan Mani, Kenrick Mock, Surjith B. Singh, Saurav Srivistava, Chris Wagner

Publications

Availability of off-the-shelf infrared sensors combined with high definition visible cameras has made possible the construction of a Software Defined Multi-Spectral Imager (SDMSI) combining long-wave, near-infrared and visible imaging. The SDMSI requires a real-time embedded processor to fuse images and to create real-time depth maps for opportunistic uplink in sensor networks. Researchers at Embry Riddle Aeronautical University working with University of Alaska Anchorage at the Arctic Domain Awareness Center and the University of Colorado Boulder have built several versions of a low-cost drop-in-place SDMSI to test alternatives for power efficient image fusion. The SDMSI is intended for use in field …

The Design Of A Racing Simulator: A Three-Phase User Testing Approach, Jakob E. Rouleau, Eric J. Wach

Human Factors and Applied Psychology Student Conference

No abstract provided.

Ergonomics In Space Flight – Past, Present, & Future, Robert Consolo

Human Factors and Applied Psychology Student Conference

From the days of “The Rocket Men” to the uprising of SpaceX, spaceflight has always inspired awe in humanity. If you examine the men that were apart of those first missions, you will find that they were not only the most capable, but won the genetic lottery to become this nations first astronauts. Looking to the times of Mercury, you see the extreme constraints that potential astronaut candidates had to meet in order to go to space. Aside from the rigorous medical testing, potential candidates also had to meet strict height and weight requirements. Early candidates could not be taller …

Designing A Mobile Space Habitat Analog, Victor Kitmanyen, Matthew Burkhard, Timothy Disher

Human Factors and Applied Psychology Student Conference

No abstract provided.

A Hybrid Vortex Solution For Surge Margin Enhancement In Axial Compressors, Daniel Port

Doctoral Dissertations and Master's Theses

A new vortex solution to the Simple Radial Equilibrium Equation (SREE) is presented that incorporates endwall effects into the preliminary design stage of a single stage, low pressure compressor with a hub-to-tip ratio of 0.4 and non-axial inlet flow. This vortex solution is proposed to overcome the rapidly approaching asymptotic peak in compressor performance in the industry today. The Hybrid Vortex theory incorporates a versatile, higher-order solution to the SREE, resulting in more accurate preliminary designs requiring less manipulation in the final design stages. This new solution results in significant changes in hub geometry with the stagger of the hub …

Nonlinear Control Of A Thermoacoustic System With Multiple Heat Sources And Actuators, Mikael O. Molina Sandoval

Doctoral Dissertations and Master's Theses

Thermoacoustic instabilities can occur in thermal devices when unsteady heat release is coupled with pressure perturbations. This effect results in excitation of Eigen-acoustic modes of the system. These instabilities can lead to unpredictable behavior of the system. Gas-turbine combustion systems are especially prone to this phenomenon reducing their overall efficiency. Additionally, due to the nature of the combustion, the turbines end up releasing undesired amounts of harmful chemicals to the atmosphere, such as Nitrous Oxide (NOX).

A Rijke tube, representing a resonator with a mean flow and a concentrated heat source, is a convenient system to study the thermoacoustic phenomena. …

Improving Damage Tolerance Of Composite Sandwich Structures Subjected To Low Velocity Impact Loading: Experimental And Numerical Analysis, Ravi B. Gondaliya

Doctoral Dissertations and Master's Theses

Sandwich structures with composite facing skins have seen applications in variety of sectors including aerospace and automobile, owing to their high specific mechanical properties. However, there is a need to develop better damage tolerant sandwich structures since conventional composite facing skins exhibit low impact resistance in the transverse direction. Here, composite skin sandwich structures with three different impact resistant core materials were fabricated and tested both experimentally and numerically. Neat CFRP and 2024-T3 aluminum alloy sheets were also investigated. Cores utilizing impact resistant D3O® were found to have very favorable weight specific energy absorbing properties at higher impact velocities as …

Cognitive Loading, Affect Regulation And Aerodynamic Considerations In Uninhabited Aerial Vehicle Systems Refueling Operations, Sam Holley, Ian R. Mcandrew

Publications

Factors influencing aerodynamics involved in aerial refueling illustrate the potential for specialist operators to manage these operations for remotely piloted vehicles. The authors review aerodynamic characteristics of uninhabited aerial systems during refueling, drogue and boom design and associated flight dynamics, cognitive factors associated with control transfer and refueling, and affective components and their influence on decision making and operator performance. Attention is directed to cognitive loading and encoding challenges, with considerations for hippocampal mapping and hemispheric asymmetry. Implications for system state awareness are examined. Advantages for specially trained refueling pilot operators are discussed and recommendations given for areas of concentration.

Hybrid Clutch Assembly For An Aircraft, Richard P. Anderson, Charles N. Eastlake, Matt Gonitzke, Glenn P. Greiner

Publications

A hybrid clutch assembly inserted between an internal com bustion engine and the propeller of an aircraft to provide a hybrid-powered aircraft. The hybrid clutch assembly allows a direct current (DC) electric motor to be attached to the hybrid clutch assembly using drive belts. The hybrid clutch assembly allows the internal combustion engine to transmit power to the aircraft's propeller and freely spin the DC motor. The DC motor can transmit power to the aircraft's propeller without turning the internal combustion engine. The hybrid clutch assembly independently allows either the internal combus tion engine or the DC motor in parallel …

Lift & Drag Reductions On Iced Wings During Take Off And Landing With Unmanned Aerial Vehicles, Ian R. Mcandrew

Publications

This research paper addresses an novel problem that has not been addressed in detail for many decades. Ice formation on aircraft has procedures and protocols to deal with expected and actual problems. Complex modern aircraft are equipped with a variety of techniques to remove Ice formation on an aircraft, especially the wings. The introduction of Unmanned Aerial Vehicles has added an old problem, that of low speed and the lack of power to overcome losses in lift through ice formation. In this research the different types of Ice formation, how they combine and affect Lift and Drag are also addresses …

Early Afternoon Concurrent Panel Sessions: Commercial Space Industry Snapshot: Presentation: Small Catapult-Assisted Horizontal-Launch Reusable Rbcc Ssto Spaceplane For Economical Short-Duration Leo Access, Nihad E. Daidzic,

Aviation / Aeronautics / Aerospace International Research Conference

This article discusses the conceptual design, flight trajectory calculations, and utilization of the possible future horizontally-launched reusable Single-Stage-to-Orbit (SSTO) spaceplane for small payload short-duration manned/unmanned access to Low-Earth-Orbit (LEO). The 10,000 lb spaceplane would use 5,000 ft catapult-assist horizontal-launch facility and conduct powered approach and landing on conventional horizontal paved runways following the gliding atmospheric re-entry. To increase the economy of operation, the launch facility located at high elevations (4,000+ ft) equatorial region is required, such as, the plateaus in Kenya and Tanzania in Africa and/or Ecuador in South America. A 500-lb payload, including pilot-commander, is envisioned. The propulsion cycle …

Apollo 13: The Longest Hour, Sy Libergot

ERAU Prescott Aviation History Program

The epic story of Apollo 13 is well known, but hear the inside details from the NASA flight controller who was on duty when the unthinkable happened. Author of Apollo EECOM, Journey of a Lifetime, Sy Libergot’s space experience began in 1966 and spanned the entire Apollo Lunar Program; Skylab; the Apollo-Soyuz project; early Shuttle and even the International Space Station, but Apollo 13 would become the unwelcome highlight of his flight controller career. Don’t miss this exciting talk by the man who was at the console when it all happened.

Determination Of Rejected Landing Roll Runway Point-Of-No-Return And Go-Around In Transport Category Airplanes, Nihad E. Daidzic, Ph.D., Sc.D.

International Journal of Aviation, Aeronautics, and Aerospace

The decelerate-accelerate-takeoff maneuver in transport category airplanes has been discussed. Mathematical model based on total energy conservation has been used to calculate the rejected landing point-of-no-return on a runway which will still enable the airplane to safely execute go-around and achieve regulatory screen heights and takeoff safety speeds. After this point has been exceeded or below the point-of-no-return speed no go-around should ever be considered. Landing long and fast and/or decelerating on slippery runways may very well result in an overrun which could be prevented if the go-around is attempted before reaching this critical runway point. The point-of-no-return on the …

A Biomimetic, Energy-Harvesting, Obstacle-Avoiding, Path-Planning Algorithm For Uavs, Snorri Gudmundsson

Doctoral Dissertations and Master's Theses

This dissertation presents two new approaches to energy harvesting for Unmanned Aerial Vehicles (UAV). One method is based on the Potential Flow Method (PFM); the other method seeds a wind-field map based on updraft peak analysis and then applies a variant of the Bellman-Ford algorithm to find the minimum-cost path. Both methods are enhanced by taking into account the performance characteristics of the aircraft using advanced performance theory. The combined approach yields five possible trajectories from which the one with the minimum energy cost is selected. The dissertation concludes by using the developed theory and modeling tools to simulate the …

An Investigation Of Cooling Configurations In Gas Turbine Engines Using Jet Impingement, Bhushan Upalkar

Doctoral Dissertations and Master's Theses

A numerical investigation for predicting the heat transfer effects of turbulence was conducted by making a scaled-up model of a section in a jet impingement channel. Different turbulence models were run and the results were compared to experimental data. Experimental comparisons were made for impingement channels between a baseline case, which is a rectangular array of jets of 20 rows and 3 jets per row, and different hole spacing configurations. The heat transfer was measured using Temperature Sensitive Paint. The turbulence model v²-f gave the most accurate prediction with an error of about 17% with the EB k-E, with an …

Direct Adaptive Control For Stability And Command Augmentation System Of An Air-Breathing Hypersonic Vehicle, Ron Aditya

Doctoral Dissertations and Master's Theses

In this paper we explore a Direct Adaptive Control scheme for stabilizing a non-linear, physics based model of the longitudinal dynamics for an air breathing hypersonic vehicle. The model, derived from first principles, captures the complex interactions between the propulsion system, aerodynamics, and structural dynamics. The linearized aircraft dynamics show unstable and non-minimum phase behavior. It also shows a strong short period coupling with the fuselage-bending mode. The value added by direct adaptive control and the theoretical requirements for stable convergent operation is displayed. One of the main benefits of the Directive Adaptive Control is that it can be implemented …

Aerodynamic Trade Study Of Compound Helicopter Concepts, Julian Roche

Doctoral Dissertations and Master's Theses

The relative performance attributes of compound helicopter concepts have been examined, including their potential for meeting the requirements of several challenging mission profiles. For each concept, which included lift and/or propulsive compounding, a suite of aerodynamic performance models was developed using energy methods. In the case of a lift-compounded concept, an aerodynamic model representing the force interaction effects of the main rotor wake with the wing was also developed. Models of a conventional helicopter and of a tiltrotor were implemented as well, and the results used as a datum for comparison. In each case, the predictive capabilities of the model …

Experimental And Computational Investigation Of Ribbed Channels For Gas Turbine Thermal Management, Yash T. Mehta

Doctoral Dissertations and Master's Theses

This study focuses on the computational benchmarking as well as validation against experimental results of a rib roughed surface in an internal channel of a stationary turbine blade. STAR-CCM+ was utilized to replace a model from a published article, and to analyze the CFD conjugate heat transfer by determining the turbulence model that best matched the published experimental values. Using those computational conditions and CFD results, an in house experimental rig was validated by comparing convective heat transfer coefficients and pressure profiles. This cooling method, when compared to a smooth channel, enhances turbulent mixing my separating and reattaching the boundary …

Lagrangian Points And Jacobi Constants For A Class Of Asteroids, Tasneem Rashid

Doctoral Dissertations and Master's Theses

Asteroid Gravitational Potentials are difficult to model owing to their irregularity in shape. This thesis focuses on two approaches to model asteroid gravity fields, namely, multiple-body and spherical harmonics modeling. Computation of gravity potential serves as a first step to determine equilibrium points called Lagrangian points for a spacecraft orbiting as an asteroid. Further, Jacobi analysis is carried out to determine zero-velocity regions, i.e., inaccessible regions corresponding to the unstable Lagrangian points. Multiple sphere modeling was studied through analysis of so called Asteroid Restricted Three and Four Body Problems, providing insight into the method of modeling an asteroid as a …

Design, Fabrication, And Testing Of A Proprioceptive Electroadhesion Pad For Space Applications, Walter Saravia

Doctoral Dissertations and Master's Theses

The purpose of this study is to design, analyze, and fabricate an electroadhesion mechanism with the goal of providing controlled electrostatic adhesion to objects with little known surface finish, of varying curvature, and different materials. The main purpose of the mechanism is that of ensuring a soft docking, controlled in closed loop, for attachment to large pieces of orbital debris. Other envisaged purposes for the mechanism are sample collection and manipulation in free-fall and in-situ analysis of cohesive forces in regolith at small bodies, such as asteroids or comets. Electrostatic finite element analysis was performed on various electroadhesion pad designs …

Numerical Study Of Synthetic-Jet Actuation Effect On Airfoil Trailing Edge Noise, Marco Sansone

Doctoral Dissertations and Master's Theses

The current study conducts numerical simulations to assess the possibility of employing Synthetic Jet Actuators (SJAs) as active noise control devices for reduction of airfoil acoustic radiation. High-accuracy numerical efforts employ a sixth-order accurate Navier-Strokes solver implementing a low-pass filtering of poorly resolved high-frequency solution content to retain numerical accuracy and stability over the range of transitional flow regimes. In the adopted numerical procedure, the actuator is modeled without its resonator cavity through imposing a simple fluctuating-velocity boundary condition at the bottom orifice of the actuator. The orifice cavity with the properly defined boundary condition is embedded into the airfoil …