Aerospace Engineering Commons^™

Determination Of Aqueous Surfactant Solution Surface Tensions With A Surface Tensiometer, Remelisa Esteves, Birce Dikici Ph.D, Matthew Lehman, Qayyum Mazumder, Nonso Onukwuba

Beyond: Undergraduate Research Journal

Surfactant solutions are applicable to engineering systems for cooling equipment for electronics. Surfactants can be added to water to improve heat transfer. An application of using aqueous surfactant solutions can be through microchannel heat sink. Although it is ideal to redesign these systems to reduce heat, it is a costly method. Surfactant solutions at optimal solution concentration can be able to transfer heat quickly and effectively with minimum expense. The surface tension of surfactant solutions is an important parameter for boiling heat transfer and must be taken into consideration. The purpose of this research is to measure surface tension of …

Determination Of Surfactant Solution Viscosities With A Rotational Viscometer, Remelisa Esteves, Nonso Onukwuba, Birce Dikici Ph.D

Beyond: Undergraduate Research Journal

Aqueous surfactant solutions are used in engineering systems for improving boiling heat transfer. The purpose of this research is to determine the viscosities of surfactant solutions and to investigate the effect of composition on viscosity. The results obtained can possibly be used as reference for further study in the effects of surfactant solution viscosities on nucleate boiling. A rotational viscometer was used to determine the viscosities of three surfactant solutions – SLS, EH-14, and SA-9 – of various compositions at room temperature. It was discovered that the viscosities of SLS, EH-14, and SA-9 had a nearly consistent pattern as their …

Commercial Space Situational Awareness (Ssa) Capabilities And Their Benefits For Civilian Space Traffic Management (Stm), Mark A. Skinner

Space Traffic Management Conference

Paralleling (but lagging) satellite development, SSA, long the sole domain of sophisticated militaries, now includes commercial providers. These commercial capabilities, identified as beneficial to the sustainable use of outer space[1], have demonstrated technical sophistication sufficient to positively contribute to the mitigation of satellite interference and provide actionable SSA information. Utilizing small optical telescopes, these entities are able to determine the orbits of objects in the geosynchronous orbit (GSO) to sizes as small as 1 m², with measured positional uncertainties of 10s of meters, on the order of the size of a modern communications satellite. These techniques …

Spaceways: Airspace In Outer Space, Scott Haeffelin

Space Traffic Management Conference

Forecasted future demand in space travel is driving the need for the development of space traffic management. Currently, orbital space traffic is mostly unregulated with internationally agreed upon best practices and self-interest driving space operators to avoid collisions with other spacecraft. This paper explores the future of space travel by presenting a concept of creating “airspace in space” or spaceways to manage the ever growing volumes of space traffic. Spaceways are analogous to airspace for aircraft with the goal of increasing levels of safety and reducing probabilities of collision. These goals can be achieved by creating traffic rules, defining valuable …

A Novel Approach For Controlled Deorbiting And Reentry Of Small Spacecraft, Larry H. Fineberg, Justin Treptow, Timothy Bass, Scott Clark, Yusef Johnson, Bradley Poffenberger

Space Traffic Management Conference

No abstract provided.

Space Analysis And Research Centers (Sparcs) For Ssa Data And Analytics, Phillip Cunio, Brien Flewelling

Space Traffic Management Conference

Widespread use of massive data and increasing reliance on spaceborne infrastructure are two of the emerging megatrends of the early 21^st century. However, both come with liabilities: movement and processing of large data volumes is very expensive, and reliance on spaceborne infrastructure adds risk that problems in the still incompletely-understood space domain might cause work disruptions.

ExoAnalytic proposes the use of Space Analysis and Research Centers (SpARCs) as a way to begin addressing both these issues. A SpARC is a facility which integrates volumes of data collected on satellites, centrally analyzes it, and makes available resulting useful information. The …

Examining Time To Evacuate Dynamically Activated Aircraft Hazard Areas, Zheng Tao, Granghuai Wang, Ashley G. Williams, Jon L. Semanek, Jonathan L. Schwartz

Space Traffic Management Conference

The growth in launch and reentry operations in the National Airspace System (NAS) presents the Federal Aviation Administration (FAA) with the challenge of integrating them more efficiently while also minimizing effects on other NAS users and maintaining safety. Currently, to maintain safety and account for unforeseen events such as vehicle breakup, the FAA segregates large amounts of airspace, called Aircraft Hazard Areas (AHAs), from traditional NAS users during launch and reentry operations. In order to minimize effects on NAS users, some AHAs during reentry are dynamically activated only if an unexpected event occurs. If a dynamic AHA is activated, then …

Air Traffic Impact Analysis Design For A Suborbital Point-To-Point Passenger Transport Concept, Tanja Luchkova, Sven Kaltenhaeuser, Frank Morlang

Space Traffic Management Conference

Space flight activities are growing on an international level, thereby creating an evident need for a safe and efficient integration of space vehicle operations into the air traffic system. For concepts like very high-speed intercontinental passenger transport via suborbital point-2-point flights, as it is proposed by the DLR SpaceLiner, this integration issue is becoming especially relevant. As part of a case study approach to analyse the effects of space vehicle operations on air traffic and to evaluate mitigation strategies and optimized ATM integration, a traffic impact analysis has been prepared and conducted for the SpaceLiner return trajectory towards a European …

A Computer Program For The Coupled Implementation Of Meanline And Throughflow Methods To Simplify The Aerodynamic Design Of Multistage Axial Compressors, Alexander V. Rozendaal

Doctoral Dissertations and Master's Theses

A computer program capable of simplifying the preliminary aerodynamic design process of multistage axial compressors has been developed. This interactive design tool, named C-STAAC, combines the Meanline and Throughflow analysis capabilities of two independent compressor design codes to form one standalone system. The program greatly improves the efficiency of the Preliminary-to-Throughflow stages of compressor design by providing fully coupled interaction between the two platforms. The result enables the user to produce stacked airfoil geometry from only a handful of initial input parameters.

The program additionally offers a wide selection of pre- and post-processing capabilities that were not previously available with …

Automotive-Inspired Inceptors And Control Laws Designed For Simplified Piloted Flight, Kashif Ali

Doctoral Dissertations and Master's Theses

This thesis details the development of a simulator-based experiment in automotive- inspired controls for aircraft. The goal is to fuse the ease of drivability of a car with the flight of an aircraft. A standard automotive control hardware setup coupled with fly-by-wire control laws will allow non-pilots to fly a plane using their familiarity with driving a car. A mathematical description of the control law logic and controller implementation is presented and the human subjects' performance is measured from data collected during experimental testing of the simulator. Preliminary results indicate that non-pilots improve their path-tracking performance and reduce control activity …

Study Of Surface Tension, Natural Evaporation, And Subcooled Boiling Evaporation Of Aqueous Surfactant Solutions, Matthew John Lehman

Doctoral Dissertations and Master's Theses

The relation between surface tension and surfactant concentration and its effect on solution evaporation under natural convection and subcooled pool boiling is examined through experimental methods. Aqueous solutions of sodium lauryl sulfate (SLS), ECOSURFTM EH-14, and ECOSURFTM SA-9 are used in this study. SLS is an anionic surfactant while EH-14 and SA-9 are environmentally-friendly nonionic surfactants.

Surfactants, surface active agents, are known to affect evaporation performance of solutions and are studied in relation to water loss prevention and heat dissipation. Surfactants could be useful under drought conditions which present challenges to water management on a yearly basis in arid areas …

Emerging Business Models For Commercial Spaceports: Current Trends From The Us Perspective, Janet K. Tinoco, Chunyan Yu

Publications

Agenda for Presentation:

• US Commercial/Government Active Launch Sites
• Why Commercial Spaceports?
• Spaceport Business Model Drivers
• Spaceport Multi-Modal Facility and Infrastructure Requirements
• Emerging Spaceport Business Models
• Summary and Concluding Remarks

Heat Transfer Analysis Of An Oblique Jet Impingement Cooling On Cmc Rough Surface, Karthik Krishna

Doctoral Dissertations and Master's Theses

A Ceramic Matrix Composite is high strength and high temperature capability composite, utilized in components like heat shield of space vehicles, flame holders and disc brakes. To be used in both static and dynamic components of a future gas turbine engine and even with high temperature capabilities of these CMC components, convection cooling will still likely be required. The surface of the CMC varies significantly from traditional super-alloy used in a modern engine, with large level of roughness and significant three-dimensional waviness. These complex features will impact the behavior of the near wall flows, and affect the heat transfer rates …

From Xst To F-117a, Alan Brown

ERAU Prescott Aviation History Program

Learn the remarkable story of stealth technology from the man often referred to as “Mr. Stealth.” From 1975-1989 Alan Brown was a member of Lockheed “Skunk Works”, becoming program manager & chief engineer for the F-117A Stealth Fighter from initial concept until the first production aircraft was built, 1978 to 1982. Hear the inside story of the many challenges faced by the stealth program and how they were solved.

2015-2016 Eraudb Aiaa Design/Build/Fly Technical Report, Trevor W. Perrott

Student Works

The economic potential of small unmanned aerial vehicles (SUAVs) has been well documented and reported. According to the Association for Unmanned Vehicle Systems International (AUVSI), there is an associated economic impact from the growth of the UAV industry. The goal of the American Institute of Aeronautics and Astronautics Design/Build/Fly Competition Research Program (AIAA DBF CRP) is to investigate design and manufacturing methods for application to SUAVs within the scope of the AIAA DBF Competition.

Students were engaged in the application of aerospace engineering knowledge for the production of a dual-aircraft system. Through the use of Computational Fluid Dynamics (CFD), Computer …

Detecting Delamination In Carbon Fiber Composites Using Piezoresistive Nanocomposites, Sandeep Chava

Doctoral Dissertations and Master's Theses

Carbon fiber prepreg composites are utilized successfully as structural materials for different lightweight aerospace applications. Delamination is a critical failure mode in these composite materials. As composite plies separate from each other, the composite loses some of its ability for supporting expected loads. Therefore, detection of delamination at right time is a foremost significance. This study presents a new way for detecting delamination in composite plates using piezoresistive nanocomposites. This new procedure is setup and studied through both experimental and computational investigations. In this research, nanocomposites with 5% coarse graphene platelets are fabricated for detecting delamination. 8-ply carbon fiber prepreg …

Vision-Aided Navigation For Autonomous Vehicles Using Tracked Feature Points, Ahmed Saber Soliman Sayem

Doctoral Dissertations and Master's Theses

This thesis discusses the evaluation, implementation, and testing of several navigation algorithms and feature extraction algorithms using an inertial measurement unit (IMU) and an image capture device (camera) mounted on a ground robot and a quadrotor UAV. The vision-aided navigation algorithms are implemented on data-collected from sensors on an unmanned ground vehicle and a quadrotor, and the results are validated by comparison with GPS data. The thesis investigates sensor fusion techniques for integrating measured IMU data with information extracted from image processing algorithms in order to provide accurate vehicle state estimation. This image-based information takes the forms of features, such …

Optimization Of Takeoffs On Unbalanced Fields Using Takeoff Performance Tool, Nihad E. Daidzic

International Journal of Aviation, Aeronautics, and Aerospace

Unbalanced field length exists when ASDA and TODA are not equal. Airport authority may add less expensive substitutes to runway full-strength pavement in the form of stopways and/or clearways to basic TORA to increase operational takeoff weights. Here developed Takeoff Performance Tool is a physics-based total-energy model used to simulate FAR/CS 25 regulated airplane takeoffs. Any aircraft, runway, and environmental conditions can be simulated, while complying with the applicable regulations and maximizing performance takeoff weights. The mathematical model was translated into Matlab, Fortran 95/2003/2008, Basic, and MS Excel computer codes. All existing FAR/CS 25 takeoff regulations are implemented. Average forces …

Suitability Testing For Possum Scientist-Astronaut Candidates Using The Suborbital Space Flight Simulator With An Iva Spacesuit, Pedro J. Llanos, Erik Seedhouse, Ryan L. Kobrick

Publications

This paper evaluates key functional data parameters that must be considered for suborbital spaceflight participants wearing pressurized suits for intravehicular activity (IVA). Data parameters of an analog spacesuit worn in an analog flight environment were obtained from 40 civilian participants using the Suborbital Space Flight Simulator (SSFS) at Embry-Riddle Aeronautical University (ERAU) while donning Final Frontier Design’s (FFD) fully pressurized third-generation spacesuit as part of their training for Project PoSSUM (the Polar Suborbital Science in the Upper Mesosphere Project). The physiological data collected included: blood pressure, electrocardiograms, heart rate, grip strength, and skin temperature. These parameters were measured using a …

Standardization Of Human-Computer-Interface For Geo-Fencing In Small Unmanned Aircraft Systems, David Thirtyacre, Robert Brents, Michael Goldfein, David Hunter, B. Terwilliger

Publications

The use of small unmanned aircraft systems (sUAS) has increased significantly in the past year. Geographic fencing (geo-fencing) is software built into most medium-cost consumer sUAS. This software is typically used to limit the altitude above launch point, the flight distance from the transmitting controller, and/or restrict flight inside a no-fly zone. While the concept of a geo-fence is simplistic, the human-computer-interface (HCI) varies drastically among platforms, and even between software iterations on the same platform. This research examines the HCI of three popular consumer-level sUAS with regard to geo-fencing. The software procedures and human interface for the DJI Inspire-1, …

Impact Of A Reverse Delta Type Add-On Device On The Flap-Tip Vortex Of A Wing, Afaq Altaf, Tan Boon Thong, Ashraf Ali Omar, Waqar Asrar

International Journal of Aviation, Aeronautics, and Aerospace

The effect of interactions of vortices produced by an outboard flap-tip of a half-span wing (NACA 23012 in landing configuration) and a slender reverse delta type add-on device, placed in the proximity of the outboard flap-tip, on the upper surface of the half-span wing is investigated using Particle Image Velocimetry in a closed loop low speed wind tunnel. Specifically the characteristics of the vortex interactions generated downstream in planes perpendicular to the free stream direction and their dependence on angles of attack at a chord-based Reynolds number of Re_c=2.75×10⁵ have been determined. It was found that the …

The Effect Of Generation On Retention Of Women Engineers In Aerospace And Industry, Kristine Maria Kiernan

Doctoral Dissertations and Master's Theses

The purpose of this dissertation was to determine the nature and extent of differences between generational cohorts regarding the effect of family factors on retention of women in engineering, with an emphasis on women in the aerospace industry. While 6% of the aerospace workforce is made up of aeronautical engineers, an additional 11.2% of the aerospace workforce is drawn from other engineering disciplines. Therefore, the analysis included all engineering sub-disciplines. In order to include women who had left the workforce, women in all industries were used as a proxy for women in aerospace.

Exits to other fields were modeled separately …

Multi-Stage Axial Compressor With Counter-Rotation Using Accessory Drive, Vinod Gehlot, Magdy S. Attia

Publications

A multi-stage axial compressor for counter rotation. A first series of rotor blade assemblies are mounted on and rotate with the driveshaft, each rotor blade assembly of the first series comprising a rotating stage of the multi-stage axial compressor. A second series of rotor blade assemblies provide a counter-rotating stage of the multi-stage axial compressor. An accessory drive links the second series of rotor blade assemblies to the driveshaft and causes counter-rotation of the second series of rotor blade assemblies.

Uav As A Service: Providing On-Demand Access And On-The-Fly Retasking Of Multi-Tenant Uavs Using Cloud Services, Justin Yapp

Doctoral Dissertations and Master's Theses

As commercial roles for Unmanned Aerial Vehicles (UAVs) become more well-defined and demand for the services provided by them increases, UAVs rely more on new cloud computing services and co-operative coordination to provide mission planning, control, tracking and data processing. We present UAV as a Service (UAVaaS) framework, which brings features commonly found in traditional cloud services, such as Infrastructure, Platform, and Software as a Service, to the domain of UAVs. Our work aims to conceptualize and design UAVaaS for commercial applications. Specifically, a cloud-provided orchestration framework that allows multi-tenant UAVs to easily serve multiple heterogenous clients at once and …

Safte-Vat Functionality Effects On Flight Instructors' Situation Awareness And Instrument Student Pilots' Performance During Ftd Training, Rafael E. Abreu Vega

Doctoral Dissertations and Master's Theses

SAFTE-VAT is a virtual air traffic control systems that adds the capability to integrate automated air traffic control functionality and generate semiautonomous and autonomous air traffic to the Frasca 172S level 6 plus FTD to improve behavioral fidelity and to facilitate flight instructors the capacity to focus more on instructing student pilots instead of role-playing ATC duties. While SAFTE-VAT may offer a more realistic ATC interaction experience onboard the FTD that may result in a positive transfer of training increase, the effects on flight instructors’ situation awareness and overall student pilot performance are uncertain. In this small study, flight instructors …

An Experimental Study Of Momentum-Driven Unsteady Jets, Sravan Kumar Artham

Doctoral Dissertations and Master's Theses

Jets are seen commonly in nature and engineering and can be broadly classified into steady and unsteady jets. The study of unsteady jets has received little attention when compared to its steady counterpart. A type of unsteady jet is the turbulent puff which is a momentum driven jet in which fluid is ejected from a jet orifice intermittently. Common examples of turbulent puff like jets are coughs and volcanoes. The studies on momentum driven unsteady jets have primarily focused on single ejection events (single puffs) where an instantaneous supply of momentum drives the source fluid downstream of a nozzle. This …

Computational Investigation Of Impingement Cooling For Regeneratively Cooled Rocket Nozzles, Bianca A. De Angelo

Doctoral Dissertations and Master's Theses

Jet impingement cooling is an internal cooling configuration used in the thermal management of temperature sensitive systems. With rocket engine combustion temperatures rising as high as 3600 K, it is essential for a cooling method to be applied to ensure that the nozzle integrity can be maintained. Therefore, a novel heat transfer study is conducted to investigate if jet impingement cooling is feasible for a regenerative cooling rocket nozzle application. Regenerative cooling for liquid propellant rockets has been widely studied. However, to the best of the author’s knowledge, there is currently no literature describing this method in conjunction with impingement …

An Experimental Study Of Synthetic Jet Actuators With Application In Airfoil Lco Control, Sanjay Krishnappa

Doctoral Dissertations and Master's Theses

An experimental study on the development and implementation of Synthetic Jet Actuators (SJAs) is conducted for eliminating aeroelastic phenomenon such as Limit Cycle Oscillations (LCO). One of the biggest challenges involved in the design of UAVs operating in unsteady atmosphere conditions is the susceptibility of the airframe to aeroelastic instabilities, such as flutter or LCO. Suppression of such instabilities can be achieved through the implementation of Active Flow Control (AFC) techniques, however to this day, a limited amount of experimental studies exist. Thus, the focus of this work is to develop a new AFC method consisting of an actuator that …

Mechanical And Electrical Characterization Of Hybrid Carbon Nanotube Sheet-Graphene Nanocomposites For Sensing Applications, Jiukun Li

Doctoral Dissertations and Master's Theses

The unique mechanical and electrical properties of carbon nanotubes and graphitic structures have drawn extensive attention from researchers over the past two decades. The electro-mechanical behavior of these structures and their composites, in which electrical resistance changes when mechanical deformation is applied facilitates their use in sensing applications.

In this work, carbon nanotube sheet- epoxy nanocomposites with the matrix modified with various contents of coarse and fine graphene nanoplatelets are fabricated. The addition of a secondary filler results in improvements of both electrical and mechanical properties. In addition, with the inclusion of the second filler, change in resistivity with mechanical …

Fluidic Jet Turbulence Generators For Deflagration To Detonation Transition In Pulsed Detonation Combustors, Jarrett E. Lowe

Doctoral Dissertations and Master's Theses

The goal of this study is to establish the dominant flow structure required to effectively accelerate the turbulent deflagration flame front to detonation velocity in the shortest possible distance while using a single Jet in Cross Flow (JICF). Jets in crossflow, depending on orientation and momentum ratio, can induce two types of flow structures that propagate downstream; vortex filaments and turbulent eddies. Vortex flow structures are coherent rotating columns that can persist for a considerable distance before diffusing. Turbulent eddies are characterized as random fluctuations in flow velocity or small pockets of rotation. The test rig used for this study …