Open Access. Powered by Scholars. Published by Universities.®

Aerospace Engineering Commons™

Open Access. Powered by Scholars. Published by Universities.®

Air Force Institute of Technology

Discipline
Keyword
Publication Year
Publication
Publication Type

Articles 571 - 600 of 1674

Full-Text Articles in Aerospace Engineering

Dynamic Constellation Tasking And Management, Steven P. Ingraham Mar 2013

Dynamic Constellation Tasking And Management, Steven P. Ingraham

Theses and Dissertations

Responsive orbits have gained much attention in recent years and many AFIT theses have addressed this topic. Specifically, the following topics have been studied: phasing within an orbit, adjusting time of arrival, avoidance, and maneuver detection. This thesis seeks to determine the feasibility of maneuvering satellites from circular (600 km) orbits to eccentric (600 km by 175 km) orbits in order to collect high resolution images for Earth surveillance. Coverage is calculated for multiple 6-satellite constellations. Perturbations for the subject orbits are analyzed and compared to simulation results.

Go to article

Effects Of Temperature On The Performance Of A Small Internal Combustion Engine At Altitude, Travis D. Husaboe Mar 2013

Effects Of Temperature On The Performance Of A Small Internal Combustion Engine At Altitude, Travis D. Husaboe

Theses and Dissertations

The effects of atmospheric pressure and temperature variations on the performance of small internal combustion (IC) engines operating at altitudes significantly above sea level are not widely documented. Using an altitude chamber and fuel-injected twostroke engine, data were collected while varying air temperature along with pressure. The peak engine power was 4.1 kW at roughly sea level standard conditions and dropped to 3.5 kW at the standard conditions for an altitude of 1.5 km. At a combination of pressure and temperature corresponding to an altitude of 3 km, peak power fell further to 2.5 kW. The combined effects of standard …

Go to article

A Study Of The Thermal Environment Developed By A Traveling Slipper At High Velocity, Kathleen H. Le Mar 2013

A Study Of The Thermal Environment Developed By A Traveling Slipper At High Velocity, Kathleen H. Le

Theses and Dissertations

The research presented in this thesis is developed from the relative sliding motion of a traveling slipper and stationary rail at the Holloman High Speed Test Track located at Holloman AFB, NM. The high velocity condition of the slipper traveling down the rail creates a thermal environment that is of interest to the researchers at the Air Force Institute of Technology. The high temperatures coupled with high velocity leads to a non-linear problem known as melt wear. The goal of this research is to characterize the amount of heat flow going into the slipper as it traverses the rail and …

Go to article

Development Of Optimized Piezoelectric Bending Actuators For Use In An Insect Sized Flapping Wing Micro Air Vehicle, Robert K. Lenzen Mar 2013

Development Of Optimized Piezoelectric Bending Actuators For Use In An Insect Sized Flapping Wing Micro Air Vehicle, Robert K. Lenzen

Theses and Dissertations

Piezoelectric bimorph actuators, as opposed to rotary electric motors, have been suggested as an actuation mechanism for flapping wing micro air vehicles (FWMAVs) because they exhibit favorable characteristics such as low weight, rapidly adaptable frequencies, lower acoustic signature, and controllable flapping amplitudes. Research at the Air Force Research Labs and the Air Force Institute of Technology has shown that by using one actuator per wing, up to five degrees of freedom are possible. However, due to the weight constraints on a FWMAV, the piezoelectric bimorph actuators need to be fully optimized to support free flight. This study focused on three …

Go to article

Finite Element Analysis Of A Highly Flexible Flapping Wing, Justin K. Mason Mar 2013

Finite Element Analysis Of A Highly Flexible Flapping Wing, Justin K. Mason

Theses and Dissertations

Small unmanned aerial systems are being designed to emulate the flapping kinematics of insects and birds which show superior control in slow speed regimes compared to fixed wing or rotorcraft aircraft. The flight of flapping wing vehicles is characterized by aeroelastic effects. Most research has been dedicated towards understanding the aerodynamic side of the aeroelastic response with minimal effort spent towards validating the structural response. A finite element model of a wing from a commercial flapping wing vehicle was created to validate the structural response. Vacuum testing allowed the isolation of the inertial response for a direct comparison to the …

Go to article

Experimental Characterization Of The Structural Dynamics And Aero-Structural Sensitivity Of A Hawkmoth Wing Toward The Development Of Design Rules For Flapping Wing Micro Air Vehicles, Aaron G. Norris Mar 2013

Experimental Characterization Of The Structural Dynamics And Aero-Structural Sensitivity Of A Hawkmoth Wing Toward The Development Of Design Rules For Flapping Wing Micro Air Vehicles, Aaron G. Norris

Theses and Dissertations

A case is made for why the structures discipline must take on a more central role in the research and design of flapping-wing micro-air-vehicles, especially if research trends continue toward bio-inspired, insect-sized flexible wing designs. In making the case, the eigenstructure of the wing emerges as a key structural metric for consideration. But with virtually no structural dynamic data available for actual insect wings, both engineered and computational wing models that have been inspired by biological analogs have no structural truth models to which they can be anchored. An experimental framework is therefore developed herein for performing system identification testing …

Go to article

Heat Exchanger Design And Testing For A 6-Inch Rotating Detonation Engine, Scott W. Theuerkauf Mar 2013

Heat Exchanger Design And Testing For A 6-Inch Rotating Detonation Engine, Scott W. Theuerkauf

Theses and Dissertations

This thesis explains the design and testing of a water-cooled rotating detonation engine (RDE) run on hydrogen and air. The change in water temperature as it cooled the engine was used to find the steady heat rate into the containing walls of the detonation channel. The engine successfully ran four times for 20 seconds each. The steady-state heat rate was measured to be 2.5% of the propellant lower heating value (LHV) into the outer wall and 7.1% of LHV into the inner wall. Additionally, a quick-response resistance temperature detector (RTD) was used in an uncooled RDE of similar dimension to …

Go to article

Experimental Analysis Of Dampened Breathing Mode Oscillation On Hall Effect Thruster Performance, Christopher D. Vineski Mar 2013

Experimental Analysis Of Dampened Breathing Mode Oscillation On Hall Effect Thruster Performance, Christopher D. Vineski

Theses and Dissertations

Experiments were performed at AFIT to determine the effect of active control of the magnetic field strength to reduce the breathing mode oscillation on the efficiency of a 200W Hall thruster. The breathing mode oscillation amplitude was measured by the root mean square (RMS) variation in the AC portion of the discharge current. Experiments were run using krypton and xenon propellant. Using the xenon propellant control of the RMS improved the propellant utilization efficiency by approximately 2% in two cases, while reducing the magnet current efficiency by about 10%. Control of the RMS's effect on the divergence angle of the …

Go to article

Training Maneuver Evaluation For Reduced Order Modeling Of Stability & Control Properties Using Computational Fluid Dynamics, Craig C. Porter Mar 2013

Training Maneuver Evaluation For Reduced Order Modeling Of Stability & Control Properties Using Computational Fluid Dynamics, Craig C. Porter

Theses and Dissertations

System identification has long been used as a tool for flight test engineers to characterize systems under test; however, the inputs to these characterization activities have previously been limited to wind tunnel and flight test data. There has been a recent effort to incorporate computational fluid dynamics (CFD) into the system identification process. An integral piece of the process is the simulation of training maneuvers utilizing CFD. Up until now, the suitability of particular training maneuvers has been assessed by comparing the reduced model to known results. This research strives to recommend a set of parameters to be used in …

Go to article

High Frequency Magnetic Field Direction Finding Using Mgl-S8a B-Dot Sensors, Michael D. Archer Mar 2013

High Frequency Magnetic Field Direction Finding Using Mgl-S8a B-Dot Sensors, Michael D. Archer

Theses and Dissertations

Aircraft based direction finding (DF) in the high frequency (HF) band is difficult due to the aircraft's size with respect to wavelength and limited azimuthal resolution. A B-dot sensor is useful for detection of the time varying magnetic field and offers improved integration into an aircraft. What the B-dot sensor gains in integration it gives up in sensitivity because it is designed for frequencies above 5 GHz. Design of an airborne HFDF array using Bdot sensors is based in maximizing the physical extent of the array and eliminating multiple main beams. The goals of this research are to complete a …

Go to article

Porous Emitter Colloid Thruster Performance Characterization Using Optical Techniques, Eric T. Wolf Mar 2013

Porous Emitter Colloid Thruster Performance Characterization Using Optical Techniques, Eric T. Wolf

Theses and Dissertations

This research focuses on experimentally characterizing the performance parameters of a colloid thruster with porous emitters through optical techniques. Porous emitters are different than traditional needle emitters in how they allow a variation in the number and size of Taylor Cones throughout a range of propellant volumetric flow rate conditions. An algorithm is created to calculate the estimated minimum and maximum number of emitter sites based on magnified images of the porous emitter heads. Theoretical thruster performance parameters are then established from the estimated number of emitter sites. Experimental techniques for measuring the thrust and exhaust exit velocity are proposed. …

Go to article

Creep Of Hi-Nicalon S Fiber Tows At Elevated Temperature In Air And In Steam, Theodore R. Shillig Mar 2013

Creep Of Hi-Nicalon S Fiber Tows At Elevated Temperature In Air And In Steam, Theodore R. Shillig

Theses and Dissertations

Structural aerospace components require materials that have superior long-term mechanical properties and can withstand severe environmental conditions, such as high temperatures, high pressures and moisture. Ceramic-matrix composites (CMCs) are capable of maintaining excellent strength and creep resistance at high temperatures, which makes them attractive candidate materials for aerospace applications, particularly in propulsion components. Silicon Carbide (SiC) ceramic fibers have been used as constituent materials in CMCs, although oxidation of the SiC to SiO2 has been a known fiber degradation mechanism. Recently developed near stoichiometric Hi-Nicalon-S fibers have shown significant improvements in thermo-chemical stability. Creep of the Hi-Nicalon-S fibers at elevated …

Go to article

Real-Time Heading Estimation Using Perspective Features, James W. Dean Mar 2013

Real-Time Heading Estimation Using Perspective Features, James W. Dean

Theses and Dissertations

There are a large number of commercially available quad-rotor helicopters available from various manufacturers. All of these systems rely on a low cost MEMS based inertial measurement system for stabilization and navigation. These low cost inertial systems are all subject to rapid error growth in their attitude and position estimates unless bounded by external measurements. This thesis created real-time algorithm to integrate measurements from visual cues with measurements from onboard sensors to estimate the attitude position and velocity of a quad-rotor helicopter in a local navigation frame, a system model for the ARDrone, and a feed-back controller for the vehicle's …

Go to article

Information Encoding On A Pseudo Random Noise Radar Waveform, Joshua A . Hardin Mar 2013

Information Encoding On A Pseudo Random Noise Radar Waveform, Joshua A . Hardin

Theses and Dissertations

Navigation requires knowledge of current location and a planned destination. This is true with manned vehicles and unmanned vehicles. There are many ways to acquire the current location, including global positioning system (GPS), triangulation, radar, and dead reckoning. Today GPS is the most reliable and accurate navigation technique when there is a clear, unobstructed view of the satellite constellation. Various sensors can be used to perform indoor navigation; however, when the vehicle is autonomous the sensors need to provide the exact location to the system. This research determined if using a template replay strategy has the same RNR performance as …

Go to article

Error Characterization Of Vision-Aided Navigation Systems, Daniel A . Marietta Mar 2013

Error Characterization Of Vision-Aided Navigation Systems, Daniel A . Marietta

Theses and Dissertations

The goal of this work is to characterize the errors committed by an Image Aided Navigation (IAN) algorithm that has been developed for use as a navigation tool in GPS denied areas. The filter under study was developed by the Air Force Institute of Technology's Advanced Navigation Technology center, and has been the focus of numerous research efforts. Unfortunately, these studies have all been based on single runs or simulations, and such results may not be indicative of the true filter performance. This problem extends to IAN publications in general; no analysis of IAN based upon a sizable real world …

Go to article

Inertial Navigation System Aiding Using Vision, James O. Quarmyne Mar 2013

Inertial Navigation System Aiding Using Vision, James O. Quarmyne

Theses and Dissertations

The aiding of an INS using measurements over time of the line of sight of ground features as they come into view of an onboard camera is investigated. The objective is to quantify the reduction in the navigation states' errors by using bearings-only measurements over time of terrain features in the aircraft's field of view. INS aiding is achieved through the use of a Kalman Filter. The design of the Kalman Filter is presented and it is shown that during a long range, wings level cruising flight at constant velocity and altitude, a 90% reduction in the aided INS-calculated navigation …

Go to article

Adaptations And Analysis Of The Afit Noise Radar Network For Indoor Navigation, Russell D. Wilson Iv Mar 2013

Adaptations And Analysis Of The Afit Noise Radar Network For Indoor Navigation, Russell D. Wilson Iv

Theses and Dissertations

After several years of development, the AFIT Noise Radar Network (NoNET) has proven to be an extremely versatile system for many standard radar functions. This pallet of capabilities includes through the wall target tracking capabilities due to its wide bandwidth and UHF operations. Utilizing White Gaussian Noise as its waveform, the NoNET can operate at much lower power levels than other comparable systems while remaining extremely covert. In an effort to explore new applications, the question arose could the NoNET provide a viable option for navigation capability in GPS denied and indoor environments? This research aims to provide proof of …

Go to article

Pseudolite Architecture And Performance Analysis For The Faa's Nextgen Airspace, Joseph A . Czabaranek Mar 2013

Pseudolite Architecture And Performance Analysis For The Faa's Nextgen Airspace, Joseph A . Czabaranek

Theses and Dissertations

By 2025 the FAA plans to have fully implemented its NextGen Airspace design. NextGen takes advantage of modern positioning technologies as well as automation, data sharing, and display technologies that will allow more efficient use of our ever busier National Airspace (NAS). A key element of NextGen is the transition from surveillance RADAR providing aircraft separation and navigation to the use of the GPS and Automatic Dependent Surveillance Broadcast (ADS-B). ADS-B couples the precision of the GPS with networked ground and airborne receivers to provide precise situational awareness to pilots and controllers. The result is increased safety, capacity, and access …

Go to article

Effects Of Stereoscopic 3d Digital Radar Displays On Air Traffic Controller Performance, Jason G. Russi Mar 2013

Effects Of Stereoscopic 3d Digital Radar Displays On Air Traffic Controller Performance, Jason G. Russi

Theses and Dissertations

Air traffic controllers are responsible for directing air traffic based upon decisions made from traffic activity depicted on 2Dimensional (2D) radar displays. Controllers must identify aircraft and detect potential conflicts while simultaneously developing and executing plans of action to ensure safe separation is maintained. With a nearly 100% increase in traffic expected within the next decade (FAA, 2012a), controllers' abilities to rapidly interpret spacing and maintain awareness for longer durations with increased workload will become increasingly imperative to safety. The current display design spatially depicts an aircraft's position relative to the controller's airspace as well as speed, altitude, and direction …

Go to article

Supplementary Computer Generated Cueing To Enhance Air Traffic Controller Efficiency, Laurienne Cibelle Rodrigues De Assis Santana Mar 2013

Supplementary Computer Generated Cueing To Enhance Air Traffic Controller Efficiency, Laurienne Cibelle Rodrigues De Assis Santana

Theses and Dissertations

Air traffic controllers are often required to simultaneously communicate with several aircraft over multiple radio frequencies. As a result, during peak loading, it is common for the controller to receive multiple concurrent communications, each from a different aircraft, making it difficult to discern audio messages received from multiple pilots simultaneously. To address this problem, a modified air traffic control (ATC) interface was prototyped with the goal of increasing controller-to-pilot communication efficiency. This prototype included supplementary text cueing which was provided by a hypothetical automated text to speech system in an on-screen text box for controller reference in the event of …

Go to article

Development Of Autonomous Optimal Cooperative Control In Relay Rover Configured Small Unmanned Aerial Systems, Timothy J. Shuck Mar 2013

Development Of Autonomous Optimal Cooperative Control In Relay Rover Configured Small Unmanned Aerial Systems, Timothy J. Shuck

Theses and Dissertations

This thesis documents the research effort to develop, integrate and implement the system hardware and the software necessary to validate the Air Force Institute of Technology's theoretical advances in small unmanned aerial systems (SUAS) cooperative control. The end state objective of the research effort was to flight test an autonomous control algorithm on a communication relay unmanned aerial vehicle (UAV) that was actively relaying data to and from a rover UAV. The relay UAV is one part of a SUAS designed to utilize cooperative control to extend the effective line-of-sight operating range for a rover UAV. An algorithm is integrated …

Go to article

Aerial Networking For The Implementation Of Cooperative Control On Small Unmanned Aerial Systems, Scott A . Songer Mar 2013

Aerial Networking For The Implementation Of Cooperative Control On Small Unmanned Aerial Systems, Scott A . Songer

Theses and Dissertations

The employment of Small Unmanned Aerial Systems (SUAS) for reconnaissance and surveillance missions is a vital capability of the United States military. Cooperative control algorithms for SUAS can enable tactical multi-vehicle configurations for communications extension, intelligent navigation, and a multitude of other applications. Past research at AFIT has designed and simulated a cooperative rover-relay algorithm for extended communications and has investigated its implementation through various modem configurations. This research explores aerial networking options for implementing cooperative control and applies them to an actual SUAS. Using Commercial Off-The-Shelf (COTS) hardware, a system was designed and flight tested to implement the rover-relay …

Go to article

Design Of A Control Moment Gyroscope Attitude Actuation System For The Attitude Control Subsystem Proving Ground, Samuel C. Johnson Mar 2013

Design Of A Control Moment Gyroscope Attitude Actuation System For The Attitude Control Subsystem Proving Ground, Samuel C. Johnson

Theses and Dissertations

All spacecraft represent a considerable investment of both time and money. To ensure mission success, testing and validation of all vital systems is crucial to the design process. The attitude control subsystem (ACS) is typically tested thoroughly, to include both hardware and control algorithms. Computer simulations offer a simple and relatively cheap method of predicting the performance of the ACS; however, computer simulations cannot provide the assurances necessary to qualify an ACS hardware configuration or control algorithm spaceworthy. For this reason, physical spacecraft simulators must be used to validate ACS dynamics. Previous research showed there is room for significant improvement …

Go to article

Film Cooling In Fuel Rich Environments, Jacob J. Robertson Mar 2013

Film Cooling In Fuel Rich Environments, Jacob J. Robertson

Theses and Dissertations

The ultra compact combustor is a high performance gas turbine design concept that portends reduced weight for future weapons platforms. A natural outcome of the design is the continual presence of fuel-rich air in the turbine component of the engine. Because modern cooling schemes for hot section turbine blades involve injecting cool, oxygen-rich air adjacent to the surface, the potential arises for reaction with the unconsumed radicals in the mainstream ow and augmented heat transfer to the blade. This outcome is contrary to the purpose of film cooling, and can lead to early life-cycle turbine failure. This study examined the …

Go to article

Design And Testing Of An H2/O2 Predetonator For A Simulated Rotating Detonation Engine Channel, Stephen J. Miller Mar 2013

Design And Testing Of An H2/O2 Predetonator For A Simulated Rotating Detonation Engine Channel, Stephen J. Miller

Theses and Dissertations

A study is presented on the relationship between a pre-detonator and a detonation channel of an RDE. Testing was conducted on a straight narrow channel made of clear polycarbonate windows connected to an H2/O2 pre-detonator to simulate the RDE initiation scheme and allow for flow visualization. A comparison is made on decoupling distance and wave velocities for a range of pre-detonator designs, inclination angles, equivalence ratios and geometries placed within the simulated channel. Regardless of inclination angle or equivalence ratio the detonation wave decoupled within 25 mm from the pre-detonator exit into the channel. A step change …

Go to article

Guided Wave-Based J-Integral Estimation For Dynamic Stress Intensity Factors Using 3d Scanning Laser Doppler Vibrometry, J. Ayers, Christopher Todd Owen, Eric D. Swenson, Anindya Ghoshal, V. Weiss Jan 2013

Guided Wave-Based J-Integral Estimation For Dynamic Stress Intensity Factors Using 3d Scanning Laser Doppler Vibrometry, J. Ayers, Christopher Todd Owen, Eric D. Swenson, Anindya Ghoshal, V. Weiss

Faculty Publications

The application of guided waves to interrogate remote areas of structural components has been researched extensively in characterizing damage. However, there exists a sparsity of work in using piezoelectric transducer-generated guided waves as a method of assessing stress intensity factors (SIF). This quantitative information enables accurate estimation of the remaining life of metallic structures exhibiting cracks, such as military and commercial transport vehicles. The proposed full wavefield approach, based on 3D laser vibrometry and piezoelectric transducer-generated guided waves, provides a practical means for estimation of dynamic stress intensity factors (DSIF) through local strain energy mapping via the J-integral. Strain energies …

Go to article

Radar Based Navigation In Unknown Terrain, Kyle J. Kauffman Dec 2012

Radar Based Navigation In Unknown Terrain, Kyle J. Kauffman

Theses and Dissertations

There is a great need to develop non-GPS based methods for positioning and navigation in situations where GPS is not available. This research focuses on the development of an Ultra-Wideband Orthogonal Frequency Division Multiplexed (UWB-OFDM) radar as a navigation sensor in GPS-denied environments. A side-looking vehicle-fixed UWB-OFDM radar is mounted to a ground or aerial vehicle continuously collecting data. A set of signal processing algorithms and methods are developed which use the raw radar data to aide in calculating the vehicle position and velocity via a simultaneous localization and mapping (SLAM) approach. The radar processing algorithms detect strong, persistent, and …

Go to article

The Effects Of Observations And Maneuvers On Orbit Solutions, Christine M. Schudrowitz Dec 2012

The Effects Of Observations And Maneuvers On Orbit Solutions, Christine M. Schudrowitz

Theses and Dissertations

The purpose of this research is to characterize the performance of the optimal sequential filter used in ODTK with a maneuvering satellite. Specifically, this thesis sought to characterize the performance using two scenarios: performance with a maneuver in between passes and performance with a limited number of measurements. The performance of the filter is evaluated by analyzing the covariance values generated during the orbit estimation process. Larger covariance values signify reduced performance of the filter. Several variables for the maneuvering satellite are used, including the maneuver direction and the maneuver magnitude. The time of the maneuver is also varied, which …

Go to article

Predicting The Wear Of High Speed Rocket Sleds, Lauren B. Wuertemberger Dec 2012

Predicting The Wear Of High Speed Rocket Sleds, Lauren B. Wuertemberger

Theses and Dissertations

Holloman Air Force Base houses the 10 mile long Holloman High Speed Test Track (HHSTT) in New Mexico and can run hypersonic experiments at speeds up to 10,000m/s. Tested objects are loaded onto sleds, which are connected to the track by slippers that slide along the rails. The payload sled is propelled down the track by a series of rocket sleds. The ability to predict the wear that will occur on the slippers during these experiments is important for slipper design and preventing catastrophic failure. However, high speeds complicate wear prediction as there additional contributing factors, including inconsistent surface contact, …

Go to article

Empirically Bounding Of Space Booms With Tape Spring Hinges, Alan L. Jennings, Jonathan T. Black, Chris Allen Nov 2012

Empirically Bounding Of Space Booms With Tape Spring Hinges, Alan L. Jennings, Jonathan T. Black, Chris Allen

Faculty Publications

Self-deploying structures seek to provide a compact launch package for large, lightweight satellite booms. One self-deploying method is a foldable tape spring. This paper examines the large scale behavior of a boom attached by a tape spring hinge during mock deployments. A boom attached by tape spring to a rigid stand was released and the boom bounced up to 60° before coming to rest (as opposed to snap-through behavior). These large amplitude bounces can cause the boom to collide with sensors, other booms or arrays causing damage or preventing full deployment. Results show the first bounce of deployment is nearly …

Go to article

First Prev Next Last