Aerospace Engineering Commons^™

Louver Slot Cooling And Full-Coverage Film Cooling With A Combination Internal Coolant Supply, Austin J. Click, Phillip M. Ligrani, Maggie Hockensmith, Joseph Knox, Chandler Larson, Avery Fairbanks, Federico Liberayore, Rajeshriben Patel

PRC-Affiliated Research

Within the present investigation, a louver slot is employed upstream of an array full-coverage film cooling holes. Cooling air is supplied using a combination arrangement, with cross-flow and impingement together. The louver consists of a row of film cooling holes, contained within a specially designed device that concentrates and directs the coolant from a slot, so that it then advects as a layer downstream along the test surface. This louver-supplied coolant is then supplemented by coolant which emerges from different rows of downstream film cooling holes. The same coolant supply passage is employed for the louver row of holes, as …

Development Of Lifting Line Theory For The Fanwing Propulsion System, Christopher Kaminski

Honors Undergraduate Theses

The FanWing propulsion system is a novel propulsion system which aerodynamically behaves as a hybrid between a helicopter and a fixed wing aircraft, and if the knowledge base with regards to this novel concept can be fully explored, there could be a new class of aircraft developed. In the current research, only 2D CFD studies have been done for the FanWing, hence the 3D lift characteristics of the FanWing have been unknown thus far, at least in the theoretical domain. Therefore, it was proposed to develop a modified Prandtl's Lifting Line Theory numerical solution and a CFD solution, comparing the …

Numerical Analysis Of Aerospike Engine Nozzle Performance At Various Truncation Lengths, Sam Dakka Dr, Oliver Dennison

International Journal of Aviation, Aeronautics, and Aerospace

The aerospike engine was first devised in the early 1960s where it provided new means of reaching orbit in a single stage. The paper aimes to demonstrate the viability of the technology by showcasing the increased nozzle thrust efficiency over the conventional bell nozzle. Various truncations were applied to the nozzle and each was subjected to two conditions, an over-expansion and near optimum condition. The nozzle contour was developed using the simple approximation method and was chosen to replicate that of the XRS-2200. This anchored the data, thereby validating the computational fluid dynamics (CFD) simulation. Simulations were completed for at …

Small Unmanned Aircraft Systems Acoustic Analysis For Noninvasive Marine Mammal Response: An Exploratory Field Study, David Thirtyacre, Gennifer Brookshire, Sarah Callan, Brittany Arvizu, Patrick Sherman

International Journal of Aviation, Aeronautics, and Aerospace

As in countless other fields of human endeavor, small unmanned aircraft systems (sUAS) have the potential to benefit pinniped (Pinnipedia; e.g., Phocidae [seals], Otariidae [sea lions], and Odobenidae [walruses]) response efforts. The employment of sUAS could give responders a close-up look at animals in distress in order to determine their condition as well as develop a response strategy. However, unlike other subjects that are regularly inspected by sUAS (e.g., croplands and civil infrastructure) pinnipeds may respond to the distinctive sound generated by small, multirotor sUAS. This reaction may include retreating into the water en masse, which could put …

Design Of A Laboratory Annular Combustor, Sathish Dharmalingam, Kartik Dolarkumar Kothari

International Journal of Aviation, Aeronautics, and Aerospace

Combustion lies at the heart of gas turbine technology. The combustor is the power source that aids the acceleration of flight. It provides the core functionality of adding heat through the controlled burn of the air-fuel mixture, converted into mechanical energy with the help of turbines. This extracted power has been used to produce thrust in the case of aircraft or to produce electrical energy in the case of industrial gas turbines. Designing an annular combustor involves a rigorous iterative process, and there is no systematic procedure available to design a small-scale laboratory combustor, used for research and academic purposes. …

Liquid Rocket Engine And Test System, Ronnie Wallingford, Grace Ann Phillips, Blake Bowser, Jack Dalton

Williams Honors College, Honors Research Projects

The goal of this project is to design the University of Akron’s first design team built liquid propulsion rocket engine and testing system. The creation of this engine and testing system will create new opportunities for the Akronauts Rocket Design Team moving forward, allowing the team to enter more prestigious competitions, and will also enable students to better pursue opportunities in the space and defense industry by exposing them to more relevant industry experiences.

The liquid rocket engine designed by the team will utilize ethanol and liquid nitrous oxide to generate approximately 500 lbf of thrust. An accompanying test system …

Electric Power Systems And Components For Electric Aircraft, Damien Lawhorn

Theses and Dissertations--Electrical and Computer Engineering

Electric aircraft have gained increasing attention in recent years due to their potential for environmental and economic benefits over conventional airplanes. In order to offer competitive flight times and payload capabilities, electric aircraft power systems (EAPS) must exhibit extremely high efficiencies and power densities. While advancements in enabling technologies have progressed the development of high performance EAPS, further research is required.

One challenge in the design of EAPS is determining the best topology to be employed. This work proposes a new graph theory based method for the optimal design of EAPS. This method takes into account data surveyed from a …

Development Of A Single Emitter Ionic Liquid Ion Source Research Platform, Thomas V. Kerber

Masters Theses

A single emitter ionic liquid ion source using porous borosilicate glass was developed. Two emitters with different radii of curvatures were tested using 1-ethyl-3-methylimidazolium tetrafluoroborate (EMI-BF₄). I-V curves of the currents on the extractor electrode and a collector plate were obtained for potential differences between the emitter and the extractor ranging from 0 V to 3500 V. For the first emitter chip, extraction began near 2400 V. The highest emission current measured on the first chip was 80 µA at 3500 V with an interception current on the extractor of 4.86 µA. An new collector plate was used …

2020 Summer-Fall Graduate Recognition Program, Propulsion Research Center, Robert Frederick

PRC Graduate Recognition

This program includes the graduate recognition program for summer and fall 2020. Includes photographs, upcoming events, recent publications, and student profiles.

Analysis For Hybrid Rocket Fuel Regression Using Stereolithographic Geometry, Michael P. King

Theses and Dissertations

Hybrid Rocket Engines (HRE) have characteristically low fuel regression that limits their performance. Additive manufacturing and rapid prototyping can possibly solve some of the problems with Hybrid propulsion regression by creating geometry not possible with conventional manufacturing. This work is attempting to make geometric regression simulation of HRE easier by using STereoLithography (STL files) as the geometry. This analysis sets flow conditions, boundary conditions, propellant selection, and allows for fuel geometry to be altered to simulate geometry’s effects on regression rate and propellant performance. This model can be used for more advanced geometric analysis to improve and predict performance.

Study Of Control Schemes For Series Hybrid-Electric Powertrain For Unmanned Aerial Systems, Darren A. Dehesa Jr

LSU Master's Theses

Hybrid-Electric aircraft powertrain modeling for Unmanned Aerial Systems (UAS) is a useful tool for predicting powertrain performance of the UAS aircraft. However, for small UAS, potential gains in range and endurance can depend significantly on the aircraft flight profile and powertrain control logic in addition to the subsequent impact on the performance of powertrain components. Small UAS aircraft utilize small-displacement engines with poor thermal efficiency and, therefore, could benefit from a hybridized powertrain by reducing fuel consumption. This study uses a dynamic simulation of a UAS, representative flight profiles, and powertrain control logic approaches to evaluate the performance of a …

Celebrating 90-Orbits Around The Sun, Stafford Air & Space Museum

Programs

In celebration of the 90th birthday of Oklahoma astronaut and aerospace legend, Gen. Thomas P. Stafford, the Stafford Air & Space Museum in Weatherford, Oklahoma is offering free admission on September 17th, 2020.

Unless stated otherwise within this repository collection, all materials are shared under the following Creative Commons license: [Creative Commons Attribution-NonCommercial 4.0 International License].

Investigating Newly Discovered Oscillation Modes In Magnetically Shielded Hall Effect Thrusters Utilizing High Speed Diagnostics, Matthew Joseph Baird

Dissertations

Magnetically shielded Hall effect thrusters (MSHETs) are a variant of Hall effect thrusters (HET) that provide the favorable thrust-to-power ratio and high specific impulse of traditional stationary plasma type (STP) HETs but with an extremely long lifetime. MSHETs exhibit unique discharge plasma oscillations compared to traditional unshielded HETs. In this study, measurements of plasma oscillations in the state-of-the-art 12.5 kW Hall Effect Rocket with Magnetic Shielding (HERMeS) were obtained at various discharge voltages while holding other operation parameters constant. Data were collected using high-speed imaging, voltage, current, and plasma probes. The thruster exhibits two dominant oscillation modes within the discharge …

Development Of High-Density Propulsion System Technologies For Interplanetary Small Satellites And Cubesats, Morgan Andrew Roddy

Graduate Theses and Dissertations

The goal of this research was to support the development of a novel propulsion system for small satellites (<180 kg) and CubeSats. This was pursued by conducting a collection of studies that were designed to provide engineering data that would be critical in designing a functional prototype. The novel propulsion system was conceived by the author to provide best-in-class performance for the small satellite and CubeSat families of spacecraft. This context presents specific design requirements that the presented technology attempts to satisfy. The most critical among these is high density; the propellant was designed to be stored with high density and the thruster was designed to be as compact as possible. The propulsion system is composed of two primary elements, a propellant generator and a thruster. The propellant generator works by sublimating a solid crystal into vapor and then using this vapor to etch a dense metal. The resulting gaseous byproducts of this reaction are the propellant. This dissertation used xenon difluoride (XeF2) vapor to etch tungsten (W) which react to form xenon gas (Xe) and tungsten hexafluoride (WF6). This approach gave a theoretical propellant storage density 5.40 g/cm3; and 5.17 g/cm3 was demonstrated. The sublimation dynamics of the XeF2 were studied as a function of surface area and temperature and it was found to be suitable for the intended application due to its high effluence rate; that is, it sublimates fast enough to be useful. The sublimation rates are on the order of 10’s of µg/s. The etch rate of XeF2 on W was also studied and found to be suitably fast to provide useful amounts of reactants for use as a propellant, again on the order of 1’s of µg/s. The thruster is an electrostatic radio frequency (RF) ion thruster design and is manufactured with Low Temperature Co-Fired Ceramic (LTCC) materials system and manufacturing technology. Manufacturing samples of the thruster were built at the University of Arkansas in July 2015 and tested at NASA’s Marshall Space Flight Center in May 2018. Testing validated the viability of the LTCC thruster and provided valuable information on how to improve the thruster’s design.

Performance Testing Of Aero-Naut Camfolding Propellers, Or D. Dantsker, Robert W. Deters, Marco Caccamo, Michael S. Selig

Publications

The increase in popularity of unmanned aerial vehicles (UAVs) has been driven by their use in civilian, education, government, and military applications. However, limited on-board energy storage significantly limits flight time and ultimately usability. The propulsion system plays a critical part in the overall energy consumption of the UAV; therefore, it is necessary to determine the most optimal combination of possible propulsion system components for a given mission profile, i.e. propellers, motors, and electronic speed controllers (ESC). Hundreds of options are available for the different components with little performance specifications available for most of them. By examining a variety of …

Aerodynamic And Aeroacoustic Performance Of Small Uav Propellers In Static Conditions, William Jordan, Robert W. Deters, Shreyas Narsipur

Publications

The proliferation of small multi-rotor UAVs in commercial, recreational, and surveillance spheres has garnered significant interest in the noise produced by these vehicles. The current research aims to study the relationship between the aerodynamic performance and acoustic characteristics of small-scale UAV propellers. Three commercially available propellers for the DJI Phantom 2/3 UAV were selected for preliminary development and validation of an aeroacoustic experimental test setup and associated data reduction methods. Propeller thrust, torque, and power measurements were recorded at static conditions. Upon successful validation of the test bench, acoustic measurements were taken at the propeller disk’s upstream and in-plane locations. …

Conceptual Design Of A South Pole Carrier Pigeon Uav, Kendrick M. Dlima

Master's Theses

Currently, the South Pole has a large data problem. It is estimated that 1.2 TB of data is being produced every day, but less than 500 GB of that data is being uploaded via aging satellites to researchers in other parts of the world. This requires those at the South Pole to analyze the data and carefully select the parts to send, possibly missing out on vital scientific information. The South Pole Carrier Pigeon will look to bridge this data gap.

The Carrier Pigeon will be a small unmanned aerial vehicle that will carry a 30 TB solid-state hard drive …

Unsteady Internal Ballistics Of A Hybrid Rocket, Naveen Sri Uddanti

Doctoral Dissertations and Master's Theses

With the recent progress made in the field of space tourism, hybrid rocket engines have gained a renewed interest due to their simplicity, low cost, operational flexibility, and safety. The flow in the ports of a hybrid rocket motor involves several coupled unsteady phenomena like moving walls, combustion in a boundary layer flow and mass addition along the port, through the regression of the solid fuel wall. The flow in the combustion chamber of a hybrid rocket is inherently unsteady because the geometry of the port varies as a function of space and time. In the current research, we develop …

Studies Of Oval Tube And Fin Heat Exchangers, Phillip Nielsen

Undergraduate Student Works

Heating Ventilation and air-conditioning (HVAC) is a system which changes the temperature of the surroundings for the purposes of cooling or heating. This system requires energy to maintain a temperature difference from the outside temperature. Optimizing the flow over the evaporator coils is one way to increase the cooling efficiency. This will reduce the power required to have a sustainable system. Optimizing the flow to increase the energy transfer between the fins and the incoming air could result in a greater Coefficient of Performance (COP). This will be achieved by changing the geometry of the tubes for greater interaction with …

2020 Spring Graduate Recognition Program, Propulsion Research Center, Robert Frederick

PRC Graduate Recognition

This program includes the graduate recognition program for spring 2020. Includes photographs, upcoming events, recent publications, and student profiles.

Zenith Propulsion, Bryce Smoldon, Matthew Boban, Maxwell Kauker, Jonathan Noble, Stefan Johnson, Andrew Lucka, Nicholas Wright

Undergraduate Student Works

Launch Vehicle Design for the FAR-Mars Competition The Zenith Propulsion team took on the challenge put forth by the Friends of Amateur Rocketry (FAR), to build and launch a rocket propelled by a liquid rocket engine. In 2018-2019, a capstone team called Tiber Designs successfully designed and tested a 1,000 lbf-thrust rocket engine, named Janus, that uses liquid oxygen and jet-A (aviationgrade kerosene) as propellants. Zenith Propulsion would design a vehicle – 21 ft long, 6 in diameter, 170 lbm loaded – that uses the Janus rocket engine to fly to a target altitude of 30,000 ft above ground level. …

Arizona Hyperloop: The Fifth Mode Of Transportation, Eleanor Pahl, Matthieu Rada

Discovery Day - Prescott

Arizona Hyperloop is a coalition between Embry-Riddle Aeronautical University and Arizona State University students competing in Elon Musk’s annual SpaceX Hyperloop Pod Competition. Hyperloop is the proposed “Fifth Mode of Transportation” - coined “a cross between a Concorde, a rail gun, and an air hockey table.” A hyperloop pod levitates and travels at nearly the speed of sound inside a vacuum tube, which eliminates air resistance. Musk hosts the annual competition to university students to encourage the evolution of urban transportation. The goal is to design, build, and race the fastest prototype pod at SpaceX’s mile-long test track in Hawthorne, …

Sae Aero West Heavy Lift Competition Team - Eaglenautics, Anthony Pirone, Evan Stuart, Jessica Millard, Nathaniel Scott

Discovery Day - Prescott

ERAU’s SAE Aero Design West Competition team encourages students of all majors who have an interest in the design of heavy-lift cargo and passenger aircraft to design, build, and fly a large RC aircraft to meet a new set of regulations each competition year. Since the team, Eaglenautics, was founded in 2017 it has successfully been to competition once in April 2019 in California. The team’s aircraft flew 4 out of 5 flight rounds, passed all technical inspections, and is now on display in ERAU’s Aero-Fab in the AXFAB. The 2020 competition requirements are unique in that the cargo’s weight-to-volume …

Launch Vehicle Design For The Far-Mars Competition, Matthew Boban, Bryce Smoldon, Jonathan Noble, Stefan Johnson, Maxwell Kauker, Nicholas Wright, Andrew Lucka

Discovery Day - Prescott

Zenith Propulsion is constructing a launch vehicle, named Altair, to compete in a competition hosted by the Friends of Amateur Rocketry (FAR) and the Mars Society. The objective for Zenith Propulsion is to design, build and launch Altair to a qualifying altitude of 30,000 feet in the FAR-Mars competition. Altair will utilize a rocket engine that has been in development at Embry-Riddle Aeronautical University’s Prescott campus since late 2018. This engine, named Janus, uses liquid oxygen and Jet-A and is designed to deliver 1000 lbf of thrust. Altair will be launched from the FAR launch site, in Mojave, CA, on …

Detonation Confinement In A Radial Rotating Detonation Engine, Kavi Muraleetharan

Theses and Dissertations

Radial Rotating Detonation Engines (RRDE) have provided an opportunity for use of a pressure-gain combustor in a more compact form compared to an axial RDE. A successfully tested RRDE has operated over a wide range of test conditions and produced detonation modes with one, two, and three waves. The presence of multiple waves located the detonation waves to the outer radius, while one wave modes operated closer to the inner radius. Locating the detonation wave closer to the inner diameter resulted in less time for combustion prior to the radial turbine. Subsequently, this tended to decrease efficiency. To attempt to …

Microturbine Turbojets: Experimental Evaluation Of Commercially Available Engines, Richard A. Depaola Iii

Theses and Dissertations

This research assessed the performance of commercial microturbine turbojets and was the first industry-wide investigation into this class of engine by AFRL's SERL. Four commercial engines of the same thrust class were evaluated for overall and component-level performance. In addition to providing an evaluation of existing systems, the maximum performance for a commercial turbojet was predicted based on component evaluations. This analysis indicated that a commercial turbojet could have comparable thrust performance to a similarly sized military-grade engine, but it is unlikely that commercial engines can achieve the SFC of military engines without upgrading the compressors found in commercial microturbines.

Development Of A Small Scale Rotating Detonation Engine, Joseph R. Dechert

Theses and Dissertations

The Rotating Detonation Engine (RDE) has been researched extensively in recent years, but the minimum size limits of an RDE have not been well investigated. The goal of this research was to build an RDE small enough to produce a detonation frequency above 20 kHz with a single detonation wave while also reducing the engine's mass ow rate. An engine with these design characteristics would reduce hazards associated with previous RDE testing. This research objective resulted in the design of an RDE with an outer diameter sized at 28 mm using ethylene and nitrous oxide as a fuel and oxidizer. …

Design And Analysis Of A Compact Combustor For Integration With A Jetcat P90 Rxi, Daniel Holobeny

Theses and Dissertations

Ultra Compact Combustors are a novel approach to modern gas turbine combustor designs that look to reduce the overall combustor length and weight. A previous study integrated an Ultra Compact Combustor into a JetCat P90 RXi turbine engine and achieved self-sustained operation with a length savings of 33% relative to the stock combustor. However, that combustor could not operate across the full stock engine performance range due to flameout at increased mass ow rates as reactions were pushed out of the primary zone. To ensure reactions stayed in the primary zone, a new design with a larger combustor volume was …

Generation Of Premix Laminar Flame Speed Library, Sai Prashanth Kumar

Dissertations, Master's Theses and Master's Reports

The Laminar flame speed is an essential parameter in measuring turbulent premixed combustion applied in Spark ignition engines. Instead of using power-law correlations, which is valid only for particular ranges, the procedure for generating a premixed laminar flame speed library is defined using MTU – Master mechanism for a wide range of charge mixture conditions inside an engine combustion chamber: Temperature (300 – 700 K), Pressure (1 – 70 bar) and reactant mixture composition of equivalence ratio (0.4 – 2.0) Laminar flame speed library is generated for methane. The mechanism's performance was improved by adjusting the pre-exponential factor of the …

Flame Stabilization Of A Premixed Jet In Vitiated Coflow, Tyler Owens

Theses and Dissertations--Mechanical and Aerospace Engineering

Premixed staged combustion in gas turbine engines can reduce emissions by lowering peak flame temperatures but can also lead to different stability characteristics when compared to traditional combustors. High pressure ratio and subsequently high temperatures can lead to conditions suitable for both autoignition and premixed flame propagation in an environment where spatial fuel/air variations are present.

An experimental facility which issues a premixed jet into a coflowing vitiated mixture was studied to examine the stability behavior, resulting in a lifted flame. The effective ignition delay observed flame was much greater than homogeneous ignition delay calculations for the same conditions. It …