Aerospace Engineering Commons^™

Lupa: An Excursion Vehicle For The Moons Of Mars, Shannon Kavanagh, Bo Lewis, Alex Odinamba, Joshua Mulhern

Senior Design Project For Engineers

Our team has designed a spacecraft and mission for exploring the moons of Mars. The Lithological and Ultraviolet Photometry Assessment (LUPA) excursion vehicle is capable of crew habitation, autonomous rendezvous, and in-vacuum sample collection all in support of a parallel Mars surface mission to be carried out in the year 2040. Our project's key focus areas revolve around orbital mechanics, space vehicle propulsion analysis, scientific exploration, and the management of various interconnected spacecraft subsystems.

Project Scrappie (Clear Constellation), Jacob Bertram, Jacob Britt, Bill Ngo, Mike Diesing

Senior Design Project For Engineers

Clear Constellation™ is a nationwide competition hosted by Rubicon® to combat the growing problem of space debris in Low Earth Orbit. Project Scrappie is our team’s solution to this problem. Scrappie is an autonomous apparatus will make use of Whipple shield technology to collide with debris at high velocities and effectively destroy the debris throughout selected orbital paths.

On Mode Transition Phenomenon And Operating Conditions In Rotating Detonation Rocket Engines, Taha Rezzag-Lebza

Electronic Theses and Dissertations, 2020-2023

The work presented herein consist of first studying the instantaneous properties of the detonation waves in a rotating detonation rocket engine by tracking each individual wave and recording its position, velocity, and peak intensity as it travels around the annulus. Results for a steady portion of a test performed on a rotating detonation rocket engine show that the wave properties exhibit oscillatory behavior. Results obtained from the rotating detonation rocket engine show that the properties are highly dependent on the azimuthal position. In an attempt to understanding the cause of such a behavior, similar investigations were performed on an air-breathing …

2021 Summer-Fall Graduate Recognition Program, Propulsion Research Center, Robert Frederick

PRC Graduate Recognition

This program includes the graduate recognition program for summer and fall 2021. Includes photographs, upcoming events, recent publications, and student profiles.

Injection Studies On A Small-Scale Rotating Detonation Engine With Improved Flow Control, Jonathan J. Wyatt

Theses and Dissertations

The Rotating Detonation Engine (RDE) has gained increasing attention in recent years for its potential advantages over typical deflagration combustion. A Micro-RDE design with an outer diameter of 28mm operating on Nitrous Oxide and Ethylene was recently developed, which stretched the limits of small-scale detonation engines. The testing on this rig has shown a stable one wave mode detonation with frequencies reaching 16.8 kHz. Key parameters that influence the detonation wave mode are cell size, fill height, and wave speed, which are heavily influence d by injection schemes. Previous testing utilized a partially premixed jets in crossflow (JIC) injection scheme, …

Optimal Sizing And Control Of Hybrid Rocket Vehicles, Srija Ryakam

Doctoral Dissertations and Master's Theses

In the present work, a genetic algorithm is used to optimize a hybrid rocket engine in order to minimize the propellant required for a specific mission. In a hybrid rocket engine, the mass flow rate of the oxidizer can be throttled to enhance the performance of the rocket. First, an analysis of the internal ballistics and the ascent trajectory has been carried out for different mass flow rates of the oxidizer as a function of time, for a fixed amount of oxidizer, in order to study the effect of throttling. Two equivalent problems are considered: in the first problem the …

Investigations Of The Negative Temperature Coefficient Region Of Sustainable Aviation Fuels For Mitigation Of Global Warming, Richard C. Smith Iii

Honors College Theses

An investigation was led to determine the correlations between the durations of Ignition Delay (ID), Combustion Delay (CD), Derived Cetane Number (DCN), Negative Temperature Coefficient (NTC), Low-Temperature Heat Release (LTHR) regions, ringing intensity, and precent mass burn, and the effect of blending the Fischer-Tropsch (F-T) synthetic aerospace fuel (SAF), iso-paraffinic kerosene (IPK), with petroleum derived Jet-A aerospace fuel on these regions. Neat blends of Jet-A and IPK and three by mass blends of the fuels will be researched. These blends include mass percentages of 75%Jet-A and 25%IPK (75Jet-A25IPK), 50%Jet-A 50%IPK (50Jet-A50IPK), and 25%Jet-A 75%IPK (25Jet-A75IPK). The study will utilize a …

Wave Energy A New Energy Mix To Produce Green Hydrogen : A Potential Future Maritime Shipping Fuel : A Study On The Port Of Ngqura, Southern Africa's "Green Status Port", Zimasa Ntombemveli Macingwane

World Maritime University Dissertations

No abstract provided.

Blade Optimization For Ground Level Low Speed Wind Turbines, Ryan Foster

Symposium of Student Scholars

Low speed wind turbines can provide inexpensive and clean energy in areas where large scale wind power generation is impractical. The purpose of this research is to explore factors that affect the efficiency of low speed wind turbine blades. The factors that were tested include angle of attack, angle of twist, chord length, average thickness, span, and taper ratio. The goal is to determine a combination of these variables to enable maximum power extraction from a low wind speed source. These blade parameters are optimized for the Southeastern region of the United States. NOAA weather data at ground level are …

Small Hall Effect Thruster With 3d Printed Discharge Channel: Design And Thrust Measurements, Ethan P. Hopping, Wensheng Huang, Kunning G. Xu

PRC-Affiliated Research

Citation: Hopping, E.P.; Huang, W.; Xu, K.G. Small Hall Effect Thruster with 3D Printed Discharge Channel: Design and Thrust Measurements. Aerospace 2021, 8, 227. https:// Abstract: This paper presents the design and performance of the UAH-78AM, a low-power small Hall effect thruster. The goal of this work is to assess the feasibility of using low-cost 3D printing to create functioning Hall thrusters, and study how 3D printing can expand the design space. The thruster features a 3D printed discharge channel with embedded propellant distributor. Multiple materials were tested including ABS, ULTEM, and glazed ceramic. Thrust measurements were obtained at the …

Small Hall Effect Thruster With 3d Printed Discharge Channel: Design And Thrust Measurements, Ethan P. Hopping, Wensheng Huang, Kunning G. Xu

PRC-Affiliated Research

Citation: Hopping, E.P.; Huang, W.; Xu, K.G. Small Hall Effect Thruster with 3D Printed Discharge Channel: Design and Thrust Measurements. Aerospace 2021, 8, 227. https:// Abstract: This paper presents the design and performance of the UAH-78AM, a low-power small Hall effect thruster. The goal of this work is to assess the feasibility of using low-cost 3D printing to create functioning Hall thrusters, and study how 3D printing can expand the design space. The thruster features a 3D printed discharge channel with embedded propellant distributor. Multiple materials were tested including ABS, ULTEM, and glazed ceramic. Thrust measurements were obtained at the …

Active Control Of Coherent Structures In An Axisymmetric Jet, Michael Marques Goncalves

Doctoral Dissertations and Master's Theses

The primary objective of this work is to develop high-fidelity simulation model for jet noise control predictions and quantify the sound reduction when an external source frequency mode excitation is imposed on the jet flow. Whereas passive approaches using mixing devices, such as chevrons, have been shown to reduce low-frequency noise in jet engines, such approaches incur a performance penalty since they result in a reduced thrust. To avoid a performance penalty in reducing jet noise, the current work investigates a open-loop active noise control (ANC) system that utilizes a unsteady microjet actuator on the nozzle lip in the downstream …

Design And Flight-Path Simulation Of A Dynamic-Soaring Uav, Gladston Joseph

Doctoral Dissertations and Master's Theses

We address the development of a dynamic-soaring capable unmanned aerial vehicle (UAV) optimized for long-duration flight with no on-board power consumption. The UAV’s aerodynamic properties are captured with the integration of variable fidelity aerodynamic analyses. In addition to this, a 6 degree-of-freedom flight simulation environment is designed to include the effects of atmospheric wind conditions. A simple flight control system aids in the development of the dynamic soaring maneuver. A modular design paradigm is adopted for the aircraft dynamics model, which makes it conducive to use the same environment to simulate other aircraft models. Multiple wind-shear models are synthesized to …

Modeling Of A Hybrid-Electric System And Design Of Control Laws For Hybrid-Electric Urban Air Mobility Power Plants, Sohail Bin Salam Lahaji

Doctoral Dissertations and Master's Theses

Advanced Air Mobility (AAM) is an emerging market and technology in the aerospace industry. These systems are being developed to overcome traffic congestion. The current designs make use of Distributed Electric Propulsion (DEP): either fully electric or hybrid electric. The hybrid engine system consists of two power sources: prime movers, such as turbine engines, and batteries. The hybrid systems offer higher range and endurance compared with the existing fully electric systems. Hybrid-electric power generation systems for AAM have different mission requirements when compared to systems used in automobiles. Therefore, there is a particular need to model hybrid-electric systems and the …

Simulation Of A Configurable Hybrid Aircraft, Brandon Bartlett

Master's Theses

As the demand for air transportation is projected to increase, the environmental impacts produced by air travel will also increase. In order to counter the environmental impacts while also meeting the demand for air travel, there are goals and research initiatives that aim to develop more efficient aircraft. An emerging technology that supports these goals is the application of hybrid propulsion to aircraft, but there is a challenge in effectively exploring the performance of hybrid aircraft due to the time and money required for safe flight testing and due to the diverse design space of hybrid architectures and components. Therefore, …

One Dimensional Study Of Magnetoplasmadynamic Thrusters For A Potential New Class Of Heavy Ion Drivers For Plasma Jet Driven Magnetoinertial Fusion, Patrick M. Brown

Theses and Dissertations

Plasma Jet Driven Magnetoinertial Fusion (PJMIF) requires high velocity heavy ion drivers in order to compress a magnetized target to fusion conditions. Previous work with heavy ion drivers has revealed sub-par accelerations due to plasma instabilities; thus, it is necessary to investigate new methods of heavy ion plasma acceleration. One such method is Magnetoplasmadynamic (MPD) thrusters. Past studies of these thrusters have been conducted at an initial temperature at or below the energy of full ionization. Here MPD thrusters are investigated using a Godunov type MHD solver with a Harten-Lax van Leer-D (HLLD) flux solving scheme assuming the plasma is …

Improving The Stability And Operability Of A Small-Scale Rotating Detonation Engine, Nathan T. Fiorino

Theses and Dissertations

A small scale RDE was designed with a channel diameter of 28 mm and channel gap of 2 mm and operated on nitrous oxide (N₂O) and ethylene (C₂H₄) as the oxidizer and fuel respectively. Changes to the original Jets in Crossflow (JIC) injection scheme and spark plug ignition method were implemented to counteract previously observed wave instabilities. Successful detonation was observed over a range of mass flows (0.035-0.068 kg/s) and equivalence ratios (ɸ = 0.6-1.4) and a stable single wave mode with frequency up to 16.8 kHz was observed for the first time. Injection …

Perfromance Improvement Of High Bypass Turbofan Engine Through Optimization Of High-Pressure Compressor Blade – A Case Study, Vlad Mandzyuk

Symposium of Student Scholars

This research determines the relation between the High-Pressure Compressor (HPC) blade characteristics, compressor pressure ratio, and lift-to-drag ratio of a high bypass turbofan engine. Alterations in the HPC blades airfoil, span, chord, taper ratio, twist, aspect ratio, sweep, and angle of incidence are performed and their effect on the engine’s performance is observed. The metrics used to compare engine performance include thrust, specific thrust, exit velocity, fuel/air ratio, power, and efficiency. Parametric cycle analysis and computational fluid dynamics are performed to compare and validate findings. The goal of this study is to optimize the design of HPC to maximize the …

Thermochemistry Of Combustion In Polyvinyl Alcohol + Hydroxylammonium Nitrate, James K. Baird, Robert A. Frederick Jr.

PRC-Affiliated Research

A mixture of polyvinyl alcohol (PVA) and hydroxylammoniun nitrate (HAN) forms a gummy solid known as a plastisol, which is ionically conducting. When an electrostatic potential of 200 V DC is applied across the plastisol, it ignites. Combustion ceases upon removal of the applied voltage. The products of PVA + HAN combustion are known to include the molecular gases carbon monoxide, carbon dioxide, water, nitrogen, and hydrogen. When the electric field within the plastisol is spatially uniform, combustion occurs preferentially at the anode. The fact that HAN is an ionic conductor suggests that the mechanism of combustion is electrolytic in …

Thermochemistry Of Combustion In Polyvinyl Alcohol + Hydroxylammonium Nitrate, James K. Baird, Robert A. Frederick Jr.

PRC-Affiliated Research

A mixture of polyvinyl alcohol (PVA) and hydroxylammoniun nitrate (HAN) forms a gummy solid known as a plastisol, which is ionically conducting. When an electrostatic potential of 200 V DC is applied across the plastisol, it ignites. Combustion ceases upon removal of the applied voltage. The products of PVA + HAN combustion are known to include the molecular gases carbon monoxide, carbon dioxide, water, nitrogen, and hydrogen. When the electric field within the plastisol is spatially uniform, combustion occurs preferentially at the anode. The fact that HAN is an ionic conductor suggests that the mechanism of combustion is electrolytic in …

Computational Investigation Of Perforated Plate Film Cooling Utilizing Conjugate Heat Transfer, Jonathan Sippel

Doctoral Dissertations and Master's Theses

The accuracy of modern state-of-practice computational fluid dynamics approaches in predicting the cooling effectiveness of a perforated plate film-cooling arrangement is evaluated in ANSYS Fluent. A numerical investigation is performed using the Reynolds Averaged Navier Stokes equations and compared to NASA Glenn’s available Turbulent Heat Flux 4 experimental measurements collected as a part of the Transformational Tools and Technologies Project. A multiphysics approach to model heat conduction through the solid geometry is shown to offer significant improvements in wall temperature and film effectiveness prediction accuracy over the standard adiabatic wall approach. Additionally, localized gradient-based grid adaption is analyzed using the …

Improving The Performance Of An Ead Aircraft By Use Of A Retractable Electrode System, Michael Alexander Fredricks

Mechanical Engineering Undergraduate Honors Theses

Electroaerodynamic (EAD) propulsion is a growing area of research for small, low powered aircraft. Recent tests of EAD aircraft have demonstrated low performance in unpowered, gliding flight. The purpose of this paper is to investigate the effect of a retractable electrode system on the flight performance of an EAD aircraft. An analysis of electrode drag contribution on the MIT ionic wind plane’s performance predicts a maximum lift to drag ratio of 22, with the addition of a retractable electrode system, for a similarly sized and modeled EAD aircraft. An experiment is developed using a prototype aircraft, launcher, and retraction system …

Analysis On Fuel Options For Scramjet Engines With The Study To Lower The Starting Mach Number, Sumantra Luitel, Gagan Dangi

Honors Theses

The main objectives of this report were to perform analysis of an ideal scramjet engine, to assess the influence of fuel on endurance factor, and the possibility of lowering the starting Mach Number of the scramjet. In the first part, an ideal cycle parametric analysis was conducted on three different fuels i.e. Liquid Hydrogen (LH2), Jet Propellant 7 (JP-7), and Rocket Propellant (RP-1), taking into account their availability, physical properties, current uses, and potential uses. The detailed analysis is done largely relying on a 9 step Parametric Cycle Analysis technique to study how fuel properties influence the variation of seven …

2021 Spring Graduate Recognition Program, Propulsion Research Center, Robert Frederick

PRC Graduate Recognition

This program includes the graduate recognition program for spring 2021. Includes photographs, upcoming events, recent publications, and student profiles.

Sensitivity And Estimation Of Aerodynamic, Propulsion, And Inertial Parameters For Rudderless Aircraft Using Simulation, Jaden W. Thurgood

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

A technique known as system identification is often used in aircraft design and testing to understand and validate the mathematical parameters that describe the aircrafts stability and handling characteristics. System identification can be thought of as the inverse of simulation. In the world of system identification, we have a physical system that we seek to understand in more detail by monitoring the system with an array of sensors. In short, we conduct tests of an aircraft while recording the inputs and response outputs. Then we take the input and output data and run it through an algorithm that seeks to …

Project Alien, Rebecca Mccallin, Madelyn Hoying, Alex Evans, Matthew Nestler, Karli Rae Sutton, Garett Craig, Lucia Secaia Del Cid, Alexander Guy, Rachel Fernandez, Amanda Trusiak, Paige Aley, Ingabire Gakwerere, Nina Dorfner, Maria Mosbacher, Mary Flavin, Selvin Hernandez, Audrey Steen, Benjamin Kazimer

Undergraduate Research and Scholarship Symposium

Project ALIEN is a comprehensive plan to send humans to Mars to look for life on the Martian surface while exploring the viability and adaptability of terrestrial microbes in Martian atmospheric conditions. ALIEN will use a ballistic capture trajectory to get to Mars and stay in aerostationary orbit for a 30-day surface mission, during which two surface crewmembers will perform a variety of experiments to achieve the mission’s goals of Martian microbial discovery within brines of the Gale Crater and terrestrial microbe adaptability and viability to Martian conditions. Experimentation is based on the presumption that Martian microbes are metabolically similar …

Aircraft Runway Safe Navigation System, David S. Obando Ortegon

Honors College Theses

Aircraft are one of the most used alternatives of traveling long distances and making them safer is a global necessity. For this reason, being able to create a functional prototype where the aircraft would be capable to acquire and process information in real time from the environment generating wingtip collision detection and simulation of a collection of exteroceptive sensors is necessary in progressing air flight safety systems. The aim of this project is to design and build, an electronic aircraft undercarriage composed with multiple exteroceptive sensors that will be able to determine and process digital information of the aircraft envelope, …

Ram Air-Turbine Of Minimum Drag, Raymond Akagi

Master's Theses

The primary motivation for this work was to predict the conditions that would yield minimum drag for a small Ram-Air Turbine used to provide a specified power requirement for a small flight test instrument called the Boundary Layer Data System. Actuator Disk Theory was used to provide an analytical model for this work.

Classic Actuator Disk Theory (CADT) or Froude’s Momentum Theory was initially established for quasi-one-dimensional flows and inviscid fluids to predict the power output, drag, and efficiency of energy-extracting devices as a function of wake and freestream velocities using the laws of Conservations of Mass, Momentum, and Energy. …

Density Measurements Of Neutral Xenon Using Multiphoton Ionization And Microwave Spectroscopy In A Hall Effect Thruster, Taylor J. Foy

Theses and Dissertations

A new dye laser and microwave scattering system for measuring low speed xenon particles was installed to characterize a commercially sourced 600 W Hall effect thruster. The new system uses multiphoton ionization and microwave spectroscopy to determine number density and velocity measurements of neutral xenon atoms in the plume of a Hall thruster. A study was conducted to ensure the new system will be able to accurately measure these neutrals in future work. The ultimate goal of this new system is to isolate and characterize the extra thrust produced in Hall Effect Thrusters due to finite volume vacuum chambers.

Louver Slot Cooling And Full-Coverage Film Cooling With A Combination Internal Coolant Supply, Austin J. Click, Phillip M. Ligrani, Maggie Hockensmith, Joseph Knox, Chandler Larson, Avery Fairbanks, Federico Liberayore, Rajeshriben Patel

PRC-Affiliated Research

Within the present investigation, a louver slot is employed upstream of an array full-coverage film cooling holes. Cooling air is supplied using a combination arrangement, with cross-flow and impingement together. The louver consists of a row of film cooling holes, contained within a specially designed device that concentrates and directs the coolant from a slot, so that it then advects as a layer downstream along the test surface. This louver-supplied coolant is then supplemented by coolant which emerges from different rows of downstream film cooling holes. The same coolant supply passage is employed for the louver row of holes, as …