Aerospace Engineering Commons^™

Interaction Of Particles With Plasma And Shock Produced By Pulsed Spark Discharge, Shomik Mukhopadhyay

Dissertations

Interactions of powders with high-temperature plasma and shockwaves occur in diverse scenarios, such as nuclear blasts, accidental industrial dust explosions, solid propellant combustion in explosive charges and when removing contaminants from surfaces. Electrostatic Discharge (ESD), known for generating shock and plasma, is a promising lab-scale technique for simulating these interactions. Studies with ESD involved placing powders near a spark-producing gap between electrodes and observing mechanical and chemical processes like particle motion and ignition. A limited range of spark conditions and material properties have been tested, which facilitated the development and validation of preliminary computational models describing this system. Significant gaps …

A Comprehensive Investigation Of The Influence Of Geometric Structure On The Shape Memory Performance Of Nafion, Jade Thomas

Physics Undergraduate Honors Theses

While perfluorosulfonic acid (PFSA) membranes have primarily been used in fuel cells due to their chemical, thermal, and mechanical stability, one PFSA, Nafion, boasts two unique characteristics: a broad glass transition (~55 °C to 130 °C) and a temperature-persistent electrostatic network. The combination of these two characteristics endows Nafion with exceptional shape memory properties – the ability of a material to morph and transform into pre-programmed shapes when exposed to an external stimulus – with enhanced permanent shape memorization, and a potentially near-infinite number of temporary shape memorization. This study focused on expanding the base of knowledge surrounding Nafion’s shape …

A Comprehensive Investigation Of The Influence Of Geometric Structure On The Shape Memory Performance Of Nafion, Jade Thomas

Mechanical Engineering Undergraduate Honors Theses

While perfluorosulfonic acid (PFSA) membranes have primarily been used in fuel cells due to their chemical, thermal, and mechanical stability, one PFSA, Nafion, boasts two unique characteristics: a broad glass transition (~55 °C to 130 °C) and a temperature-persistent electrostatic network. The combination of these two characteristics endows Nafion with exceptional shape memory properties – the ability of a material to morph and transform into pre-programmed shapes when exposed to an external stimulus – with enhanced permanent shape memorization, and a potentially near-infinite number of temporary shape memorization. This study focused on expanding the base of knowledge surrounding Nafion’s shape …

Starfish: A Compact, Biomimetic, And Adaptive Shape Memory Alloy Orbital Debris Remover, Katelyn Branaman

Doctoral Dissertations and Master's Theses

This thesis aims to turn the tides on the orbital debris issue through the fabrication and demonstration of a compact, biomimetic, and adaptive shape memory alloy actuated orbital debris remover. The design, referred to as Starfish, is discussed in detail along with its fabrication process and object capture ability. A hard skeleton crafted from PETG was combined with shape memory alloy wires and extension springs to create a biomimetic structure that operates similar to the human hand, capable of gripping a wide range of objects. Relevant simulations were performed and discussed, the iterative fabrication process used to create each component …

A Comparison Of Beamforming Characteristics In Isotropic And Composite Plate Structures For Use In Structural Health Monitoring, Sarah Ketchersid

Doctoral Dissertations and Master's Theses

Structural health monitoring in plate-like simple structures using phased array beamsteering of guided Lamb waves is useful in damage detection and evaluation efforts. Lamb waves can be effectively used for beamsteering using a linear array. The experimentation primarily focuses on beamsteering in the aluminum panel, which involves developing a simulation based on extracted data to visualize the dispersion of waves across the panel. By evaluating parameters such as slowness, velocity, and amplitude direction and variation for a specific metallic plate, the wavefront generated by a single wave source can be represented as a function of propagation angle and distance from …

Influence Of Environmental Barrier Coatings On The Overall Effectiveness Of A Film Cooled Ceramic Matrix Composite Plate, Shane P. Lindsay

Theses and Dissertations

Silicon carbide ceramic matrix composites, a promising new potential upgrade over the conventional metals currently used for jet engine turbine blades, have a propensity to oxidize in a combustion environment. Engine manufacturers often apply environmental barrier coatings to prevent the composites from oxidizing. What is unclear, however, is how environmental barrier coatings effect underlying composite temperatures. This research examined the coatings’ effects by first characterizing the influence of environmental barrier coatings on the underlying temperature of a protected ceramic, then evaluating the significance of lateral conduction for cooling a coated ceramic, and finally comparing cooling results for coated and uncoated …

Deep Learning Based Optical Flow Analysis Of High-Speed Flows, Daniel H. Zhang, Zifeng Yang

Mechanical and Materials Engineering Faculty Publications

Two-dimensional Rayleigh scattering imaging is utilized to quantify the high-speed flow velocity by employing deep learning based optical flow analysis, along with density fields from Rayleigh scattering intensity profiles.

Kissing Bond Assessment In Adhesive Bonded Carbon Fiber Reinforced Composites Using Dielectric Spectroscopy, Minhazur Rahman

Mechanical and Aerospace Engineering Dissertations - Archive

The widespread use of fiber-reinforced composites in industries such as space, aviation, automobiles, and construction necessitates the formation of robust composite joints between critical structural components. Although adhesive-bonded joints are superior with improved load distribution and reduced weight, they are often overlooked in favor of bolted joints and mechanical fasteners due to the lack of reliable Non-Destructive Evaluation (NDE) techniques for adhesive-bonded composites. The anisotropic nature of the substrate and the intricate interfacial interactions between the adherend and adhesive material present significant challenges for conventional NDE methods. Moreover, weak adhesive bonds can result from uncontrolled manufacturing parameters, such as accidental …

Experimental Investigations And Optimization Of 3d Printed Cellular Structures For Protection Against Traumatic Brain Injury, Aaron R. Jackson

Mechanical and Aerospace Engineering Dissertations - Archive

Traumatic Brain Injury (TBI) disrupts brain function due to head impacts, blast exposures, and ballistic penetrations. It is a significant cause of mental health issues and disability, particularly among military personnel. Historically, combat helmets were designed primarily to protect against fragments. However, recent data highlights the need for helmets that also protect against blast and blunt impacts. Effective TBI prevention requires helmets that address various energy threats while remaining lightweight. A critical metric in this effort is head acceleration, which is closely linked to injury across different scales of brain damage.

Four lattice structures were 3D printed using Digital ABS …

Generating Blood Analog For Laser Induced Fluorescent Particle Image Velocimetry, Chungyiu Ma, Jared Chong, Hang Yi, Zifeng Yang, Luke Bramlage, Bryan Ludwig

Mechanical and Materials Engineering Faculty Publications

To mimic blood non-Newtonian viscosity features under designated temperatures from 305 to 315 K, transparent blood analogs were generated by the mixture of xanthan gum and deionized water with fluorescent particles for laser induced fluorescent particle image velocimetry.

Graphene Reinforced Polymer Composite For Small-Scale Vertical Axis Wind Turbine Rotors, Kunal A. Bachim

Mechanical and Aerospace Engineering Theses - Archive

Polymers have evolved as an indispensable asset in various sectors ranging from packaging and construction to energy and aerospace. However, the accumulation of polymer waste poses a necessity to shift toward sustainable waste management processes. Mechanical recycling is a primary method in establishing a circular economy approach for polymers. However, a fundamental challenge arises in this process: a decrease in the mechanical performance of the recycled product compared to that of its pristine counterpart.

This project addresses the challenge of enhancing the recyclability of polyethylene terephthalate (PET) from discarded polymer material by incorporating graphene nanoparticles into the polymer matrix during …

3d Flow Field Quantification In An Artery Model Using Optical Flow Method Based On Simulated Multi-Angle Angiography, Zifeng Yang, Hang Yi, Luke Bramlage, Bryan Ludwig

Mechanical and Materials Engineering Faculty Publications

3D flow field in a numerically simulated arterial model is quantified using the three-dimensional optical flow method based on simulated simultaneous multi-angle X-ray angiography of the blood flow with contrast agent perfusions.

Restoration Of Strength In Polyamide Woven Glass Fiber Organosheets By Hot Pressing, Mohammad Nazmus Saquib, Edwing Chaparro-Chavez, Christopher Morris, Kuthan Çelebi, Diego Pedrazzoli, Mingfu Zhang, Sergii G. Kravchenko, Oleksandr G. Kravchenko

Mechanical & Aerospace Engineering Faculty Publications

Thermoplastic composite organosheets (OSs) are increasingly recognized as a viable solution for automotive and aerospace structures, offering a range of benefits including cost-effectiveness through high-rate production, lightweight design, impact resistance, formability, and recyclability. This study examines the impact response, post-impact strength evaluation, and hot-pressing repair effectiveness of woven glass fiber nylon composite OSs across varying impact energy levels. Experimental investigations involved subjecting composite specimens to impact at varying energy levels using a drop-tower test rig, followed by compression-after-impact (CAI) tests. The results underscore the exceptional damage tolerance and improved residual compressive strength of the OSs compared to traditional thermoset composites. …

Dual Airfoil Testing System, Zifeng Yang, Collin Charvat, Jack Stafford, Kyle Mathews, Logan Kelly

Mechanical and Materials Engineering Faculty Publications

A dual airfoil testing system includes a platform including a frame defining a chamber that is configured to receive a horizontal flow of air for testing a first airfoil and a second airfoil contained in the chamber and a control system including a controller to control a first attack angle stepper motor, a second attack angle stepper motor, at least one gap stepper motor, and at least one stagger stepper motor. The controller is configured to automatically control and adjust the stepper motors to control and adjust the attack angle of the first airfoil, the attack angle of the second …

A Concept Of Producing Aluminum In-Situ On The Moon Through Molten Salt Electrolysis, Jacob N. Ortega, Jeffrey Smith, Fateme Rezaei, David Bayless, William Schonberg, Daniel Stutts, Daoru Han

Materials Science and Engineering Faculty Research & Creative Works

This paper presents a concept of producing aluminum in-situ on the lunar surface, namely, the Lunar In-Situ Aluminum Production through Molten Salt Electrolysis (LISAP-MSE) method developed at Missouri University of Science and Technology. This paper aims to demonstrate the use of electro-deoxidation to reduce aluminum oxide (i.e., alumina) into aluminum and oxygen gas via electrolysis in a molten salt bath for the production of aluminum on the Moon. It is shown that with a steady supply of hydrogen chloride, this in-situ resource utilization (ISRU) method could supply several necessary materials consumed in the electro-deoxidation process except hydrogen chloride to produce …

Effect Of Post-Cured Through Thickness Reinforcement On Disbonding Behavior In Skin-Stringer Configuration, Jimesh D. Bhagatji, Christopher Morris, Yogaraja Sridhar, Bodhisatwa Bhattacharjee, Krishnanand N. Kaipa, Oleksandr G. Kravchenko

Mechanical & Aerospace Engineering Faculty Publications

An experimental investigation of interlaminar toughness for post-cured through-thickness reinforcement (PTTR) skin-stringer sub-element is presented. The improvement in the crack resistance capability of skin-stringer samples was shown through experimental testing and finite element analysis (FEA) modeling. The performance of PTTR was evaluated on a pristine and initial-disbond of the skin-stringer specimen. A macro-scale pin-spring modeling approach was employed in FEA using a non-linear spring to capture the pin failure under the mixed-mode load. The experimental results showed a 15.5% and 20.9% increase in strength for the pristine-PTTR and initial-disbond PTTR specimens, respectively. The modeling approach accurately represents the overall structural …

Control Of Flow Instabilities With Acoustic Metamaterials, Jensen E. Mctighe

Open Access Master's Theses

Acoustic metamaterials (AMs) have been proposed for uses in flow control, as they offer a passive control method and can be engineered independently, without needing complex fluid structure interactions simulations. For example, AMs embedded into flat plate surfaces have been demonstrated to delay (or speed up) the onset of laminar-to-turbulent boundary layer transition by attenuating (or strengthening) Tollmein-Schlicting waves through numerical simulation. However, as of present, no experimental research has been conducted to study or demonstrate the behaviors of AMs designed to interact with flow structures. An experiment was performed in which an AM was embedded into a flat plate …

Electrostatic Sorting Of Lunar Regolith Simulants For Sustainable Resource Utilization: Modeling And Characterization Of Particle Size Distribution, Abdullah Al Moinee, Peter Bachle, Kyle Newport, William Schonberg, David Bayless, Jeffrey Smith, Daoru Han, Fateme Rezaei

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

In pursuit of sustainable resource utilization on the Moon, this paper delves into modeling and characterization of particle size distribution (PSD) of lunar regolith simulants in an electrostatic system. A prototype electrostatic sieve was built and tested with four sample simulants mirroring properties of lunar mare and highland regolith. An alternating four-phase (90 degrees, 180 degrees, 270 degrees, 360 degrees) traveling square-wave was utilized for particle-directed transport to model the diverse trajectories of the particles. Numerically, we scrutinized how the distribution functions of the particles are manifested as the electrostatic field propagates, with a focus on three distinct particle ranges …

Molecular Modeling Of Phenolic Resin For Carbon-Carbon Composites, Ivan Gallegos

Dissertations, Master's Theses and Master's Reports

One of the most difficult challenges associated with space exploration is terrestrial atmospheric reentry due to the high thermal loads generated. Carbon carbon (C/C) composites have been used as heat shielding materials due to their high strengthto- weight ratio and thermal properties and their applications include heat shielding for various high temperature environments. C/C composites are manufactured by polymer-infiltration pyrolysis (PIP) via cycles of curing and pyrolysis of a prepreg which can be costly and take up to several days. Thus, C/C composites ideal candidates for computationally-driven optimization techniques, such as a multiscale Integrated Computational Materials Engineering (ICME) approach, by …

Materials Testing For Large Format 3d Printing, William Jenkins

Williams Honors College, Honors Research Projects

An ABS Carbon Fiber blend was printed into single walled hexagons at a variety of settings on a Cincinnati BAAM large format 3D printer. These hexagons were then cut down into sheets and had tensile and flexural test samples cut out of them, in order for materials testing to be performed. Tensile strength, tensile strain, young’s modulus, flexural strength, deflection and elastic modulus were all determined. A desktop CNC machine and a planer were purchased for the manufacturing of these samples, and an efficient cutting procedure was designed and optimized. After all data collection concluded, this data was thoroughly analyzed, …

Short Strand Carbon Fiber Reinforced Polylactic Acid Filament For Additive Manufacturing, Dale Chenoweth, Lukas Seggi, Luke Phillips

Williams Honors College, Honors Research Projects

In this design project, the additive manufacturing filament of short strand carbon fiber (SSCF) reinforced polylactic acid (PLA) composite was developed. The micro-size, precision cut SSCFs were mixed with the PLA pellets through a melting homogenization process. Through this process the composite material block is cut and divided into pieces for ease of pelletizing. The material block pieces are then pelletized to be fed through the single screw extruder to develop the SSCF-PLA composite filament. The SSCF-PLA filaments were manufactured with a varying amount of SSCF ranging from 0.5% to 10% of the material block's weight. Development of a 1% …

Ambient Temperature Strength Degradation Of A Ceramic Matrix Composite Due To Solid Particle Erosion, Jonathan Clawson

Williams Honors College, Honors Research Projects

Solid particle erosion (SPE) is an issue for aircraft exposed to hard, fine particles, such as sand or dust, that can be ingested into the engine at a high velocity without reaching their melting point, resulting in material removal. SPE can be attributed to the intake of particulate debris from the runway or from airborne particulates. The cumulative mass loss from SPE damage affects the structural integrity and performance of the engine; however, its effects on ceramic matrix composites (CMCs), that are being employed in the aerospace industry, are not well understood in literature. The limited SPE research studies that …

Electrostatic Sorting Of Lunar Regolith Simulants For Sustainable Resource Utilization: Modeling And Characterization Of Particle Size Distribution, Abdullah Al Moinee, Peter Bachle, Kyle Newport, William Schonberg, David Bayless, Jeffrey Smith, Daoru Han, Fateme Rezaei

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

In pursuit of sustainable resource utilization on the Moon, this paper delves into modeling and characterization of particle size distribution (PSD) of lunar regolith simulants in an electrostatic system. a prototype electrostatic sieve was built and tested with four sample simulants mirroring properties of lunar mare and highland regolith. an alternating four-phase (90 degrees, 180 degrees, 270 degrees, 360 degrees) traveling square-wave was utilized for particle-directed transport to model the diverse trajectories of the particles. Numerically, we scrutinized how the distribution functions of the particles are manifested as the electrostatic field propagates, with a focus on three distinct particle ranges …

Bioprinting With Adipose Stem Cells And Hydrogel Modified With Bioactive Glass, Krishna C.R. Kolan, Apurv Saxena, Bradley A. Bromet, Lesa B. Steen, August T. Bindbeutel, Julie A. Semon, Delbert E. Day, Ming C. Leu

Biological Sciences Faculty Research & Creative Works

Bioprinting research is focused on utilizing growth factors and multiple cell types to create clinically relevant three-dimensional (3D) tissue models using hydrogels. Rheological and biological challenges are two main factors that limit the creation of extrudable bioactive hydrogels. In this study, we investigate incorporation of fast dissolving and bioactive borate glass in different weight to volume percentages (0.075 to 0.6%) to alginate-gelatin (1:1) hydrogel to improve rheological properties and enable bioprinting with bioactive glass. The addition of glass improved the stiffness of the hydrogel. Human adipose-derived mesenchymal stem cells (ASCs) were uniformly mixed in this bioink at 1 x 106 …

Experimental Characterization And Quantification Of Deformation Behavior In A Porous Carbon Fiber Network, Robert N Quammen

Theses and Dissertations--Chemical and Materials Engineering

Due to their wide range of attractive functional properties (such as low thermal conductivity and low density) porous materials are utilized in a variety of applications. In order to characterize these properties and others, the intrinsically heterogeneous microstructures of these materials need to be taken into account. These microstructures result in interactions across multiple length scales spanning several orders of magnitude. This makes the creation of robust computational models and straight-forward predictions of mechanical properties difficult for porous materials. With this in mind, this dissertation aims to provide experimental mechanical and deformation information spanning the length scales of interest for …

A Concept Of Producing Aluminum In-Situ On The Moon Through Molten Salt Electrolysis, Jacob N. Ortega, Jeffrey Smith, Fateme Rezaei, David Bayless, William Schonberg, Daniel Stutts, Daoru Han

Materials Science and Engineering Faculty Research & Creative Works

This paper presents a concept of producing aluminum in-situ on the lunar surface, namely, the Lunar In-Situ Aluminum Production through Molten Salt Electrolysis (LISAP-MSE) method developed at Missouri University of Science and Technology. This paper aims to demonstrate the use of electro-deoxidation to reduce aluminum oxide (i.e., alumina) into aluminum and oxygen gas via electrolysis in a molten salt bath for the production of aluminum on the Moon. It is shown that with a steady supply of hydrogen chloride, this in-situ resource utilization (ISRU) method could supply several necessary materials consumed in the electro-deoxidation process except hydrogen chloride to produce …

Progress Of Lisap-Mse: A Concept Of Producing Aluminum In-Situ On The Moon Through Molten Salt Electrolysis, Jacob N. Ortega, David Bayless, Daniel Stutts, Daoru Han, Todd P. Sander, Jeffrey Smith, Fateme Rezaei, William Schonberg

Mechanical and Aerospace Engineering Faculty Research & Creative Works

This paper presents a concept of producing aluminum in-situ on the lunar surface, namely, the Lunar In-Situ Aluminum Production through Molten Salt Electrolysis (LISAP-MSE) method developed at Missouri University of Science and Technology. This paper aims to demonstrate the use of electro-deoxidation to reduce aluminum oxide (i.e., alumina) into aluminum and oxygen gas via electrolysis in a molten salt bath for the production of aluminum on the Moon. It is shown that with a steady supply of hydrogen chloride, this in-situ resource utilization (ISRU) method could supply several necessary materials consumed in the electro-deoxidation process except hydrogen chloride to produce …

Magnetic Separation Of Lunar Regolith Simulants With Applications To In Situ Resource Utilization On The Moon, Peter Bachle, Jeffrey Smith, Fateme Rezaei, David Bayless, William Schonberg, Daoru Han

Materials Science and Engineering Faculty Research & Creative Works

The development of in situ resource utilization (ISRU) for metal extraction is imperative as a steppingstone for habitation construction in lunar and non-terrestrial environments. Separation of minerals by chemical composition is important to optimize metal and oxygen liberation from lunar ore. to this effect, devices capable of separating aluminum bearing minerals from iron-bearing minerals from the lunar regolith simulants have been developed. Twenty-eight different simulants have been used in this study. a dual-belt separator was designed to reduce middlings. Para-magnetic minerals were reliably separated using a neodymium N52-magnet-separator system. Effective separation of aluminum-bearing minerals from iron-bearing minerals was greater than …

Beneficiation Of Lunar Regolith Simulants Through Electrostatic Sieving And Magnetic Separation, Peter Bachle, Jeffrey Smith, Fateme Rezaei, David Bayless, William Schonberg, Daoru Han

Materials Science and Engineering Faculty Research & Creative Works

In the light of future development of lunar structures, in-situ feldspar beneficiation is imperative for metal extraction. This research incorporates the tandem use of electrostatic sieving and magnetic separation for collecting a specific size range and mineral composition from lunar soil that optimizes subsequent chemical processing. While earlier works focused on silt-sized particles, this work expands that range up to medium-grained sand with a greater variety of potential lunar regolith compositions. This work shows that a 2.5 kV, 7 Hz to 30Hz frequency, single-phase square wave can lift silt and fine sand for collection. This lifting is successful directly from …

Kinetic Modeling Of Electrostatic Sieving For Lunar Regolith Beneficiation: Case Studies, Easton Ingram, Emmanuela Amen Eze, Jeffrey Smith, Fateme Rezaei, David Bayless, William Schonberg, Daoru Han

Materials Science and Engineering Faculty Research & Creative Works

A new kinetic particle modeling framework was developed to investigate electrostatic transport of lunar regolith particles with applications to the concept of electrostatic sieving. The new approach is based on kinetic particle dynamics and includes major modules of sampling the particle size distribution, solving electric fields, and tracking motion of charged dust grains. Case studies for a concept of electrostatic sieving were chosen to validate the new model. The simulation achieved similar yields reported in previous works, which served as validation of the model. The new model is computationally efficient and could serve as a design, analysis, and optimization tool.