Aerospace Engineering Commons^™

Vortex Generated Rotor Wake Model For Real-Time Simulation, Kenneth S. Graham

Link Foundation Modeling, Simulation and Training Fellowship Reports

The University of Alabama Flight Dynamics Laboratory (UA FDL) has been simulating helicopters since 1981. The real-time, man-in-the-loop, simulator was developed locally and is continuously being upgraded. The hardware, software, architecture and math models are all developed in-house by a team of faculty and graduate students. Since 1994, the UA rotor model has been Bladehelo [2] - a true blade model that numerically integrates the flapping motion of individual blades and the shaft rotation. The approach is physically based. Discrepancies are studied until they are understood. Bladehelo played a key role in the discovery of residual bending [3], [4]. Bladehe!o …

Efficient Dynamic Unstructured Methods And Applications For Transonic Flows And Hypersonic Stage Separation, Xiaobing Luo

Mechanical & Aerospace Engineering Theses & Dissertations

Relative-moving boundary problems have a wide variety of applications. They appear in staging during a launch process, store separation from a military aircraft, rotor-stator interaction in turbomachinery, and dynamic aeroelasticity.

The dynamic unstructured technology (DUT) is potentially a strong approach to simulate unsteady flows around relative-moving bodies, by solving time-dependent governing equations. The dual-time stepping scheme is implemented to improve its efficiency while not compromising the accuracy of solutions. The validation of the implicit scheme is performed on a pitching NACA0012 airfoil and a rectangular wing with low reduced frequencies in transonic flows. All the matured accelerating techniques, including the …

Design Methodology For Low Speed High Altitude Long Endurance Unmanned Aerial Vehicles, Aaron Altman

Mechanical and Aerospace Engineering Faculty Publications

High Altitude Long Endurance (HALE) Unmanned Aerial Vehicles (UAV's) are increasingly being considered to perform a wide range of tasks. Recent years have seen greater value of UAV's in the military reconnaissance arena, first in the Persian Gulf war, with the use of small UAV's, and more recently over Bosnia with medium sized UAV's.

The NASA ERAST program uses HALE UAV's for environmental sensing and monitoring. The military has investigated using HALE UAV's for Theater Ballistic Missile defense, as well as general battlefield reconnaissance. Proposals have been made to use HALE UAV's for communications relay, long term surveillance (with a …

Vortex Wake And Exhaust Plume Interaction, Including Ground Effect, Ihab Gaber Adam

Mechanical & Aerospace Engineering Theses & Dissertations

Computational modeling and studies of the near-field wake-vortex turbulent flows, far-field turbulent wake-vortex/exhaust-plume interaction for subsonic and High Speed Civil Transport (HSCT) airplane, and wake-vortex/exhaust-plume interaction with the ground are carried out. The three-dimensional, compressible Reynolds-Averaged Navier-Stokes (RANS) equations are solved using the implicit, upwind, Roe-flux-differencing, finite-volume scheme. The turbulence models of Baldwin and Lomax, one-equation model of Spalart and Allmaras and two-equation shear stress transport model of Menter are implemented with the RANS solver for turbulent-flow modeling.

For the near-field study, computations are carried out on a fine grid for a rectangular wing with a NACA-0012 airfoil section and …

Wind Tunnel Testing For Drag Reduction Of An Aircraft Laser Turret, Christopher H. Snyder

Theses and Dissertations

This study investigated the use of aft-mounted fairings and splitter plates to reduce the drag of a half-scale aircraft laser turret. Forces, moments, and pressure distributions were measured in the AFIT 1.5-m (5-ft) wind tunnel at Reynolds numbers between 3x10⁵ and 9x10⁵ based on the turret diameter. Oil traces indicated the nature of the flow near the surface of the unmodified turret and the surrounding area. Tufts placed on the turret, fairings, and splitter plates showed changes in separation regions when configurations were changed. The flow around the turret was characterized by dominant vortices shedding from the top …

The Effect Of Nonvertical Shear On Turbulence In A Stably Stratified Medium, Frank G. Jacobitz, Sutanu Sarkar

School of Engineering: Faculty Scholarship

Direct numerical simulations were performed in order to investigate the evolution of turbulence in a stably stratified fluid forced by nonvertical shear. Past research has been focused on vertical shear flow, and the present work is the first systematic study with vertical and horizontal components of shear. The primary objective of this work was to study the effects of a variation of the angle θ between the direction of stratification and the gradient of the mean streamwise velocity from θ=0, corresponding to the well-studied case of purely vertical shear, to θ=π/2,corresponding to purely horizontal shear. It was observed that the …

The Design And Testing Of An Inlet-Airfoil For A High Altitude Remotely Piloted Aircraft, Preston Bradley Martin

Mechanical & Aerospace Engineering Theses & Dissertations

The following work describes and validates a methodology for the aerodynamic design of a low drag, efficient inlet-airfoil to be used on the cooling installations of a high altitude remotely piloted aircraft. Owing to the primary aircraft design requirement of subsonic endurance at high altitude (85,000 ft), the flight conditions present an aerodynamically unfavorable combination of low chord Reynolds number (500,000) and high subsonic Mach number (0.5). At this flight condition, the inlet-airfoil must meet the heat exchanger cooling flow requirements while maintaining the aerodynamic performance of the airfoil. As a result, the design method is closely coupled with not …

The Influence Of Surface Roughness On Supersonic High Reynolds Number Turbulent Boundary Layer Flow, Robert M. Latin

Theses and Dissertations

A comprehensive study of rough-wall high speed (M=2.9) high Reynolds number (R_e/m = 1.9 x 10⁷) turbulent boundary layer flow was performed consisting of experimental, analytical, and numerical methods. Six wall topologies consisting of a smooth and five rough surfaces (two and three dimensional machined roughness plates; and 80, 36, and 20 grit sand-grain roughened plates) were studied. A confocal laser scan microscope was used to measure the topography of the sand grain roughnesses. The experimental measurement techniques included a convention Pitot pressure probe, laser Doppler velocimetry, hot wire anemometry; color schlieren and laser …

Analysis Of Turbulence Models As Applied To Two- And Three-Dimensional Injection Flows, Clarence R. Chenault

Theses and Dissertations

A steady state solution of the full, three dimensional Favre averaged Navier Stokes equations, coupled with a second order Reynolds stress turbulence model (RSTM) and an eddy viscosity model were used to numerically simulate oblique injection into supersonic flow. Numerical results were compared to experimental data and the turbulence models were evaluated for accurate prediction of thermomechanical mean flow variables, Reynolds stresses, flowfield shock structure and boundary layer phenomena. The RSTM simulation resulted in physically consistent and accurate predictions for the mean flow and turbulent quantities. Simulations with the eddy viscosity model resulted in non-physical and inconsistent turbulence predictions. RSTM …

Effect Of High Free Stream Turbulence On Film Cooling Using Double Row Of 30° Slant-Hole Injectors, Lilith I. Sorensen

Theses and Dissertations

In this study free stream turbulence levels from 7.3% to 17.8% are applied to film cooling over a flat plate with two rows of 30° slant holes using a wall jet as the main stream air supply and source of turbulence. Blowing ratios are varied from 0.25 to 2.0 and free stream velocities at injection range from 10 m/s to 85 m/s. A constant density ratio of 1.07 is kept throughout the experiment. Results show that for different magnitudes of blowing ratio free stream turbulence has a different influence on effectiveness. At the forward stations, where blow off was present …

Flow Field And Loading Analysis On A Wrap-Around Fin Missile, Thomas C. Mcintyre

Theses and Dissertations

Wrap-around fin (WAF) missiles offer packaging benefits but experience rolling moments due to the curved fin design. Rolling moments stabilize unguided projectiles, but cause guidance and control problems for future guided applications. Understanding the flow field in the vicinity of the fins is critical to future missiles. Fin pressure profiles were characterized with pressure-sensitive paint. Two rectangular four-fin constructions were tested-one solid and one with a rectangular hole (slotted fin). Static pressure data were divided by free-stream total pressure for presentation. Tests were conducted at Mach numbers of 2.15, 2.28, 2.41, 2.86, 3.25, 3.50 and 3.83. Reynolds numbers based on …

Experimental Investigation Of The Influence Of Molecular Weight On Mixing And Penetration In Supersonic Dissimilar Gaseous Injection Into A Supersonic Cross-Flow, Troy A. Giese

Theses and Dissertations

In pursuit of a more efficient and effective fuel-air mixing for a SCRAMjet combustor, this study investigated relative near field effects of molecular weight on mixing and penetration of different gaseous injection into a supersonic (M=2.9) cross flow. Helium and argon gas were chosen as injectants because of the large differences in molecular weights. Also, mixing enhancement was observed by injecting the traverse gas jet parallel to the compression face of a ramp. Color schlieren photography was used to identify the shock structures and interactions in the flow field. Measurements of mean flow properties were used to establish the jet …

Three-Dimensional Aerodynamic Design Optimization Using Discrete Sensitivity Analysis And Parallel Computing, Amidu Olawale Oloso

Mechanical & Aerospace Engineering Theses & Dissertations

A hybrid automatic differentiation/incremental iterative method was implemented in the general purpose advanced computational fluid dynamics code (CFL3D Version 4.1) to yield a new code (CFL3D.ADII) that is capable of computing consistently discrete first order sensitivity derivatives for complex geometries. With the exception of unsteady problems, the new code retains all the useful features and capabilities of the original CFL3D flow analysis code. The superiority of the new code over a carefully applied method of finite-differences is demonstrated.

A coarse grain, scalable, distributed-memory, parallel version of CFL3D.ADII was developed based on "derivative stripmining". In this data-parallel approach, an identical copy …

Aerodynamic Gradient-Based Optimization Using Computational Fluid Dynamics And Discrete Sensitivities For Practical Problems, Mohagna Jayendrarai Pandya

Mechanical & Aerospace Engineering Theses & Dissertations

A gradient-based shape optimization methodology based on quasi-analytical sensitivities has been developed for practical three-dimensional aerodynamic applications. The flow analysis has been rendered by a fully implicit, finite-volume formulation of the Euler and Thin Layer Navier-Stokes (TLNS) equations. The flow equations and aerodynamic sensitivity equation have been solved using an alternating-direction-implicit (ADI) algorithm for memory efficiency. A wing geometry model based on space-surface and planform parameterization has been utilized. The present methodology and its components have been tested via several comparisons.

Initially, the inviscid flow analysis for a wing has been compared with those obtained using an unfactored, Preconditioned Conjugate …

Numerical And Experimental Investigation Of The Flowfield Near A Wrap-Around Fin, Carl P. Tilmann

Theses and Dissertations

A wall-mounted semi-cylindrical model fitted with a single wrap-around fin (WAF) has been investigated both numerically and experimentally, with the objective of characterizing the mean and turbulent flowfield in the vicinity of the fin. Numerical and experimental results are used to determine the nature of the flowfield and quantify the effects of fin curvature on the character of the flow near WAFs. This research has been motivated by the need to identify possible sources of a rolling moment reversal observed at high speeds in sub-scale flight tests. Detailed mean flow and turbulence measurements were obtained in the AFIT Mach 3 …

A Feasibility Study Of Fuel Cell Cogeneration In Industry, Scott B. Phelps, J. Kelly Kissock

Mechanical and Aerospace Engineering Faculty Publications

Up until now, most of the literature on fuel cell cogeneration describes cogeneration at commercial sites. In this study, a PC25C phosphoric acid fuel cell cogeneration system was designed for an industrial facility and an economic analysis was performed. The US DOE Industrial Assessment Center (IAC) database was examined to determine what industry considers a good investment for energy saving measures. Finally, the results of the cogeneration analysis and database investigation were used to project the conditions in which the PC25C might be accepted by industry.

Analysis of IAC database revealed that energy conservation recommendations with simple paybacks as high …

Experimental Investigation Of Compressible Boundary Layers Under The Influence Of Pressure Gradients, Raymond C. Wier

Theses and Dissertations

This study examined the effect of mild pressure gradients on the mean and turbulent flow of high-speed boundary layers. Three Mach numbers (1.7, 3.0 and 5.0) were investigated. Three pressure gradients were examined; a zero pressure gradient (ZPG), a favorable pressure gradient (FPG), and a combined pressure gradient (CPG). The CPG consisted of an adverse pressure gradient followed by a favorable pressure gradient. Conventional pressure probes, hot-wire and particle image velocimetry (PIV) were used to examine the flow. Measurement included mean velocity, velocity turbulence intensity, mass flux turbulence intensity and energy spectra. Instantaneous (10 nsec) Mie scattering flow visualizations were …

Experimental Investigation Of Transverse Supersonic Gaseous Injection Enhancement Into Supersonic Flow, Mark P. Wilson

Theses and Dissertations

In pursuit of more efficient and effective fuel-air mixing for a SCRAMJET combustor, this study was conducted to investigate relative near field enhancements of penetration and mixing of a discrete low-angled (25°) injected air jet into a supersonic (M=2.9) cross flow. The enhancements were achieved by injecting the transverse air jet parallel to the compression face of eight different ramp geometries. The jet-ramp interactions created collinear shock structures, baroclinic torque vorticity enhancement, ramp spillage enhanced vorticity, magnus effect penetration enhancement, and increased total pressure loss. Shadowgraph photography was used to identify the shock structures and interactions in the flow field. …

The Effectiveness Of Film Cooling In A Hypersonic Flowfield With Favorable Pressure Gradients, Julie A. Young

Mechanical & Aerospace Engineering Theses & Dissertations

The impetus of this technical document is to report results of aerothermodynamic cooling of a scramjet nozzle under favorable pressure gradients. The goals of film cooling are to protect the nozzle skin from the high enthalpy combustor flow, reduce regenerative cooling requirements, and decrease nozzle skin friction. A hypersonic nozzle configuration for which experimental data exists was selected as the basis of this numerical study. As a first step, the numerical results of film cooling along a flat plate are compared to previous literature to validate the numerical model. Subsequently, computations are performed to study the effects of varying the …

A Study Of The Numerical Implementation Of Multidisciplinary Design Optimization Strategies, Rodney A. Taylor

Mechanical & Aerospace Engineering Theses & Dissertations

Design optimization provides an organized, systematic, and efficient method for obtaining design improvements based upon a specified measure of design performance. In the multidisciplinary design optimization (MDO) environment efficient optimization techniques allow complex designs to be improved by managing conflicting disciplinary design goals so as to improve the global design. This thesis studies the implementation issues surrounding MDO techniques and strategies. To facilitate this investigation two testbed problems have been selected for study. These problems consider two approaches to the conceptual design of an aeroelastic wing. The first approach is based on an idealized, two-dimensional representation of an airfoil under …

Direct Measurement Of Skin Friction In High Temperature And Impulsively Started Supersonic Flowfields, David M. Hazelton

Theses and Dissertations

This study further developed and improved a miniature plastic cantilever floating element gauge for direct measurement of skin friction in shock tunnel tests. Gauge durability and usability were improved, and potential sources of error were quantified. A high frequency 30 kHz gauge (compared to the baseline 10 kHz gauge) was constructed by using an I-beam cantilever rather than a round beam. A directional gauge was developed and demonstrated by measuring the flowfield about a fin in the AFIT shock tunnel. The 10 kHz and 30 kHz gauges were used in two scramjet test sequences conducted at Mach 14 enthalpy (stagnation …

Nonlinear Analysis Of Airfoil Flutter At Transonic Speeds, Scott A. Morton

Theses and Dissertations

Hopf-bifurcation analysis is used to determine flutter boundaries of a pitch and plunge airfoil (PAPA) at transonic Mach number conditions. The PAPA model is a coupling of the Euler equations and a two-degree-of-freedom structural model composed of linear and torsional springs. The Euler equations are discretized using an upwind total variation diminishing scheme (TVD) of Harten and Yee. Equilibrium solutions of the PAPA model are computed using Newton's method and dynamic solutions are explicitly integrated in time with first-order accuracy. The Hopf-bifurcation point, which models the flutter condition, is computed directly by solving an extended system of equilibrium equations following …

Sensitivity Analysis And Optimization Of Aerodynamic Configurations With Blend Surfaces, Almuttil Mathew Thomas

Mechanical & Aerospace Engineering Theses & Dissertations

A novel (geometrical) parametrization procedure using solutions to a suitably chosen fourth order partial differential equation is used to define a class of airplane configurations. Inclusive in this definition are surface grids, volume grids, and grid sensitivity. The general airplane configuration has wing, fuselage, vertical tail and horizontal tail. The design variables are incorporated into the boundary conditions, and the solution is expressed as a Fourier series. The fuselage has circular cross section, and the radius is an algebraic function of four design parameters and an independent computational variable. Volume grids are obtained through an application of the Control Point …

Study Of Surface Heat Exchangers For High-Altitude Atmospheric Research Aircraft, Te-Kang Wang

Mechanical & Aerospace Engineering Theses & Dissertations

A flush-mounted heat exchanger concept, using the wing surface to dissipate heat, is investigated as a lower drag alternative to conventional ducted plate-fin radiators. A feasibility analysis is made for an unmanned high-altitude aircraft which will reach altitudes up to 25 kilometers. A computer code is used to calculate approximate heat transfer coefficients over the airfoil's surface. A model is tested in the Old Dominion University subsonic wind tunnel to verify the results of the computer code. The results indicate that a flush mounted heat exchanger design is able to provide 20 to 100 percent of the required heat dissipation …

Compressible Turbulence Measurements In A Supersonic Boundary Layer With Impinging Shock Wave Interaction, Michael J. Meyer

Theses and Dissertations

No abstract provided.

An Investigation Into The Effects Of Lateral Aerodynamic Asymmetries, Lateral Weight Asymmetries, And Differential Stabilator Bias On The F-15 Directional Flight Characteristics At High Angles Of Attack, David R. Evans

Theses and Dissertations

The F-15 is a stable aircraft throughout most of its flight envelope. However, it still exhibits an uncommanded yawing and rolling tendency at high angles-of-attack. Identified influencing factors of this uncommanded motion are lateral aerodynamic asymmetries, lateral weight asymmetries, and differential stabilator bias. Previous research into the effects of these influencing factors has been qualitative. This thesis quantifies the effects and then identifies a symmetric F-15 configuration. The quantifying metric presented is net yaw acceleration. This thesis used both computer simulation and experimental flight test to quantify these effects. A discussion of each influencing factors effects on the F-15B high …

Riblet Effects On Gortler Vortex Development Over A Concave Surface, James A. Rothenflue

Theses and Dissertations

Riblet effects on Goertler vortex development in laminar and transitional flows were measured using three-dimensional laser-Doppler anemometry. Three freestream velocities were tested such that riblet spacing corresponded to Goertler vortex (GV) wavelengths which presumably would be either strongly amplified, weakly amplified, or attenuated by centrifugal forces on a curved surface. Experiments revealed the development of paired, counterrotating vortices within the riblet valleys over both flat and concave surfaces. For riblet spacings equivalent to weakly or non-amplified GV wavelengths, GV development on a curved surface was above the riblets and was delayed by the addition of riblets. The GV wavelength was …

An Experimental Investigation Of A Sting-Mounted Finite Circulation Control Wing, Lorenzo C. Bradley Iii

Theses and Dissertations

This study investigated the lift, drag and pitching moment performance of a circulation control wing in the AFIT 5-ft wind tunnel. The experimental wing model was a 20 percent thick, 8.5 percent camber, partial elliptical cross-section, single blowing slot, rectangular planform wing. The aspect ratios tested were 3.99, 3.77 and 3.75. The variables in the investigation included the slot blowing rate and model configuration. The model was modified by adding a leading edge nose droop, a trailing edge splitter plate and wing tip fences to improve flow at the leading edge, reduce separation effects, and encourage attached flow on the …

Numerical Simulation Of Supersonic Turbulent Boundary Layer Flow Under The Influence Of Mild Pressure Gradients, Eric T. Fick

Theses and Dissertations

Mach 2.9 boundary layer flow (R_e/m ≈ 1.75x10⁷) under the influence of mild pressure gradients is studied numerically. Baldwin-Lomax and k - ω turbulence models are incorporated into a cell centered finite volume flow solver and the results are compared with hot wire anemometry and Laser Doppler Velocimetry (LDV) measurements obtained for the same geometries in the AFIT Mach 2.9 wind tunnel. Agreement between the present simulations obtained with the k - ω turbulence model and experimental velocity profiles is excellent in all test sections. Nondimensional turbulent shear stress predictions closely match experimental data in the …

Experimental Investigation Of A Supersonic Turbulent Boundary Layer With Adverse Pressure Gradient, Chad S. Hale

Theses and Dissertations

Laser Doppler Velocimetry (LDV) measurements were made to quantify the effect of adverse pressure gradient on the compressible turbulent flow structure in a Mach 2.9 boundary layer (Re/m= 1.75 x 10⁷). Measurements included profiles of 2-D mean velocities, turbulence intensities, Reynolds shear stresses, intermittency, flatness and skewness. In addition, mean strain rates were also measured. The boundary layer measurements were acquired for both flat plate and compression ramp models. LDV measurements were made at two locations on the compression ramp model at 68 cm and 71 cm downstream of the nozzle throat. At these locations, Β …